Search Documents

By M.A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By M. A. Hunter

This paper gives the results of an investigation of the specific resistance and temperature coefficient of the electrical resistance of nickel and its important alloy, monel metal. For most of the pure metals, the temperature coefficient of resistance is approximately 0.004 per degree centigrade at 20" C. Nickel and iron, however, are exceptions. This property is important as it gives us good material for the construction of thermometers and other instruments involving electrical control. A summary of information on this subject has been publishcd by the Bureau of Standards.l The present experiments antedate this publication by several years and as the information obtained is not contained in it, the results of the experiments arc published as additional information. Electrical Properties of Pure Nickel It is generally conceded that the lowest values for electrical resistance are obtained in the purest metal. In the case of nickel, the best material obtainable is electrolytic nickel, which contains approximately 99.80 per cent. nickel, 0.15 per cent. iron, and 0.05 per cent. copper. Any cobalt that may be present is included in the nickel figure. If the elcctrolStic sheet has been deposited without intermission, it is possible to cut a section from the sheet and roll it into wire without melting. By this means a nickel wire may be obtained that is uncontaminated by any of the impurities always taken up by nickel during melting. Two samples of nickel wire obtained from different electrolytic nickels had the follolving electrical resistance and temperature coefficient of electrical resistance: Specific Temp. CofEE. Sample MateRial ReSISTance peR Deg. C. NO. 1 Electrolytic nickel.................... 7.55 0.00550 NO. 2 Electrolytic nickcl ................... 7.60 0.00553 * Rensselacr Polytechnic Institute. Director of Research, Driver-Harris Co. Russell Sage Laboratory, Rensselaer Polyt,ecllnic Institute. 1 U. S. Bureau of Standards, Circular 100 (March, 1921).

Jan 1, 1923

By Henry E. Armitage

The object of this paper is to give a few useful hints on the concentration of low-grade ores. The machines that I shall speak of are, Cornish rolls, revolving screens, Hartz jigs, spitz-lutte, and the Linkenbach buddle (or Roberts's patent buddle, as it is called in Colorado). I think the reason why some of them have been discarded in favor of more recent inventions is that they have not been given a fair chance to do their work in a satisfactory manner. Cornish rolls are usually looked upon as a machine designed simply to crush the ore as a preliminary to sending it to the sizingscreens, beyond which they have nothing to do with dressing the ore. On the contrary, the rolls give the key-note to the whole process. It is well known that one class of rock will crush differently from another, and from the result obtained by passing the ore through the rolls the size of the first revolving screen and the surface required on the jig-screens must be determined. If it is found that the mineral crushes clear from the quartz, a large mesh can be used on the first sizing-screen, and the tailings will not require recrushing ; but if it is found that some of the tailings from the first jig are ragged (that is, are carrying off particles of mineral sticking on the quartz), it will be necessary to recrush them. Again, if a large percentage of the tailings carry off mineral, it will be more economical to commence with a finer mesh screen than to recrush the tailings. Having determined the best mesh to use on the first sizing-screen, the different sizes on the other screens can be determined from it. I have found for practical purposes that, commencing with a 6-mesh, the next should be 8, then 12, and finally 18. The holes in the jig-screens should be a trifle larger than in the revolving screens. For instance, if the revolving screen is made of No. 14 wire, the corresponding jig-screeus should be of No. 16 wire. The jig-screen surface required for each size made depends on the may

Jan 1, 1890

By Hannu Penttila, Harrison R. Cooper, Olli Mattila

Two approaches to automated operation in metallurgical processes involve the conventional analog control or, more recently, digital control. The expanding use of digital controls applied to process automation is a comparatively new development. Several current technical reports describe digital control systems in concentrator grinding control, 1, 2, flotation, 3 and smelter operations. 4,5 The principle factors influencing trends to digital control are:

Jan 10, 1976

By A. Ojanen, T-L. Huggare, A. Kuivala

An electrolytic zinc plant with a capacity of 90,000 tons/year went on stream in Kokkola, Finland, in late 1969. It is a standard electrolytic zinc process plant; however, it has been subjected to several process improvements and enlargements during its time of operation. A fluidized bed roaster treats 500 tons/day of zinc concentrates which also contain mercury. Since the mercury evaporates completely in the roasting process, a mercury removal unit has been added to prevent, contamination of sulphuric acid produced in the neighbouring acid plant. The same unit also removes selenium from the roaster gases. In a separate unit, about 6 tons a year of metallic 99.999% mercury is recovered. The neutral leaching, originally a batch process, has been converted to a continuous operation, and a residue treatment system comprising hot acid leaching and jarosite precipitation has been added. Purification comprises a "hot arsenic-zinc dust" step and a cadmium removal step with zinc dust, both operated batchwise. Purification residues are used to make about 200 tons/ year of 99.99570 cadmium in a process developed by Outokumpu Oy. The electrolytic precipitation of zinc carried out at medium current density gives zinc of 99. 995% purity.

Jan 1, 1973

In Mr. Weed's interesting paper, frequent reference is made to the Cananea copper-deposits, which are said to have been so vigorously exploited that they produced 14,000,000 Ib. of copper in 1901. The ore-bodies which yielded this large quantity of metal are described as a product of contact-metamorphism, and in Mr. Weed's genetic classification of such deposits, they receive a place under the sub-heading, "Deposits impregnating and replacing beds of contact-zone."* They are considered by Mr. Weed to represent a special type under this head, and are further classified as: " l. Chalcopyrite deposits: (a) Pyrrhotite ores; (6) Magnetite ores, Cananea type." In condensing much information into a comparatively small space, the presentation of a subject may be so abbreviated as to detract from its clearness. The situation at La Cananea, considering its importance from an economic as well as scientific standpoint, may he worthy of more detailed description. As Mr. Weed rightly remarks, " structural differences are so important, and have SO marked a bearing, not alone on the theory of their genesis, hut also on the working of the deposits and a determination of their value as mines, that they merit a full discussion."† It is my present purpose: (1) to show that it is doubtful whether the copper of La Cananea is mined, except to a limited

Jan 1, 1903

By Francis P. Sinn

IN the zinc smelting industry the year 1947 seems to have been one of putting one's house in order rather than one of any material technical development or radical change in operating conditions. Labor generally has been in better supply but several plants report a scarcity of skilled workmen. Some plants continue to operate on the basis of a six-day week and will probably continue to do so until labor is more plentiful. Only one plant is known to have operated on a curtailed basis because of labor shortage, but here the difficulty was lack of proper housing facilities. Necessary materials and equipment for much-needed maintenance and modernization have been in short supply so these programs have often been delayed. Laborsaving devices of the "Payloader" type have been more generally used for handling materials. Slab zinc production was discontinued during the last months of the year at Danville, 111. and at Langeloth, Pa. Both of these plants used the Hegeler type of furnaces fired with producer gas. It is understood that the rolling mill and possibly the acid plant at Danville will continue to operate. At Langeloth acid will be produced from

Jan 1, 1948

By Clarence W. Dunham

BECAUSE of the earthquakes that occur at Chuquicamata, the design of the smelter stacks constituted the most difficult structural problem of the entire sulphide ore project. Slight tremors occur almost daily and shocks of moderate magnitude are not uncommon. Naturally, the operation of the smelter depends upon the safety of these stacks, and their resistance to earthquakes was the critical feature of their design. Adequate data of the magnitudes of past shocks at Chuquicamata were not available. However, considering the information that was obtained from experiences in other parts of Chile, a period of one to two seconds was adopted as a basis for the design. To complicate the problem further, the stacks had to provide for operations under a wide variety of conditions ranging from the possibility of running one reverberatory furnace and two converters initially to perhaps five or six furnaces and eight or ten converters simultaneously in the completed plant. No one could tell for certain just what the ultimate capacity might have to be because the plans permitted a large extension beyond the first installation if this became necessary. Studies of the stacks were made for many conditions. At first it was thought that one stack 600 or 650 ft high should be used initially for both the furnaces and converters, with a second similar stack to be built for the future extension. This height would provide adequate draft in the rarified atmosphere at the plant's elevation of 10,000 ft. It would also disperse the gases high in the air. Preliminary studies of this large stack showed that such a structure was possible if made of steel but it would be exceedingly costly. Furthermore, the effects of the tendency for the top to whip under the action of earthquakes might be serious, and the design had to be based upon assumptions which might not be trustworthy. Such a tall stack was finally abandoned in favor of a larger number of smaller ones. Initially, one stack will service the first three or four furnaces. Another will handle the gases from four or five converters. The smelter has been located in such a position that the prevailing winds carry the fumes away from the remainder of the plant. A height of 300 ft for the stacks was finally selected. The top diameter is approximately 24 ft 9 in. clear inside of the lining. The converter stack is located upon a hill alongside the smelter. This provides an effective increase in height because its base is approximately 66 ft above the yard level. The base of the reverberatory stack is at the latter elevation. Stacks made of reinforced concrete or of steel were investigated, and so were many shapes for them. As these studies progressed, the lightness of a steel structure, and the ductility of the metal itself, led to the decision to use steel for the main part of the stacks. The fact that serious damage to one of the stacks would cause the plant to shut down, caused special studies to be made of the stress conditions that might exist around the breeching which had to be nearly 15 ft wide and 40 ft or more high where it joined the stack. This height was necessary in order to provide adequate transition from the horizontal flow of the gases to the vertical direction without undue eddies. This opening constituted a serious source of weakness in the structure. If made with sufficiently strong reinforcement around its edges, there would be a hard spot in the structure that might cause trouble because of shaft vibrations.

Jan 1, 1952

By Geoffrey Purcell

For anyone contemplating flotation research with only a very limited amount of mineral available for testing, the choice of suitable experimental equipment is by no means obvious. Hallimond's original and delightfully simple cell1 has been modified by subsequent investigators2to give quantitative and reproducible results on small samples. However, the modifications have necessarily compromised its simplicity, and the services of a skilled glass blower are required to duplicate the cell. Vacuum flotation tests3 at best qualitative and may, under certain conditions4, be quite impracticable. A hundred years ago, Thoreau observed that "our life is frittered away by detail," and his advice was to "simplify, simplify," The success of the simple cell described below, which was developed by the author and differs somewhat from Hallimond's original, suggests that Thoreau's advice still has merit a century later. CELL CONSTRUCTION The cell [Fig. 1 (a) and 1 (b)] consists essentially of a 25-ml pipet from which has been cut the con- stricted top. The length cut off is not critical since this merely determines the final volume of the cell. Cell volume may be varied in this way from 20 to 50 cc. A pyrex extension tube, equal in diameter and approximately half the length of the cut pipet, is attached to the top of the pipet by means of 2 ½ in. of close-fitting tygon tubing. When assembled, the two pyrex tubes should be spaced about ½ in. apart. Another length of tygon tubing is added to the extension piece for sealing purposes. A ¾ -in. disc of porous material (teflon cloth is ideal), secured in place over the pipet tip with another piece of shaped tygon tubing, completes the cell assembly. Tygon tubing may be shaped by pushing it over the pipet tip or some similar form and heating carefully over a low flame. For flotation [Fig. 1 (c) 1, the pyrex extension tube is rotated approximately 70º from the vertical and held in position by a wire hook and eye. Floated material, after reaching the free surface, falls and rests on this inclined plane. The barrier formed by the bent tygon tubing ensures that floated material does not slide back and return to the vertical portion of the cell.

Jan 11, 1965

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By E. L. Fisk

First discovered and claimed in 1929, the Cordero cinnabar deposit lies 11 road miles southwest of McDermitt, Nev., near the Nevada-Oregon boundary. The name "Cordero" means "little lamb" in the Basque language and is symbolic of the fact that the first ore specimen was found during the lambing season. The Bradley Mining Co. held the property for several years during the early thirties, but it was not until 1939 that Cordero Mining Co., a subsidiary of Sun Oil Co., entered the picture. The company, then known as Horse Heaven Mines, Inc. conducted preliminary work in 1940 which proved enough near-surface ore to warrant the construction of a mill during the following year. By 1943, Cordero was being rapidly depleted when deeper churn drilling intersected the large underground orebody that is still being mined today.

Jan 11, 1961

R. F. McELVENNY.- Mr. Oldright has just given me a letter to read to you, which I think it may be of interest. It is headed, "Silver Meeting Dinner". The letter is as follows: "To Members of the A. I. M. & M E.: The annual business meeting and election of officers will take place at the University Club, Wednesday, May 28th, 1930 at 7 p.m., at the Silver Meeting Dinner. The Nominating. Committee for next year's officers have proposed the following names: Chairman, Robert Wallace; Vice-Chairman, G. W. Crane; secretary, C. T. Van Winkle, Other nominations can be made at the meeting. Utah being the leading silver producer of the United States, constructive suggestions regarding the silver situation will be made at this meeting which are new and of general interest to the members. The speak¬ers will be followed by a Round Table discussion of the silver situation and proposed remedies. Speakers will be - W. M. Ferry, President of the Silver Producers' Association, 'Recent developments in the Silver Question'.. Senator Frank J. Cannon, 'The Cannon Plan'. George W. Snyder, 'The Manufacture of Sterling Silver.' Discussion by J. J. Beason, G. W. Crane, J. 0. Elton, J. W. Wade and others. Members of the Conference on Copper Reverberatory Smelting are invited to be present. Chairman J. A. Norden will preside. C. T. Van Winkle, Secretary. Dinner will be $1.50 per plate." The next subject is "Boilers: Proper construction of, so as to secure best utilization of heat from gases, and facility in removing dust and clinker with minimum losses in operation." Who is particularly interested in that subject? The type of boilers is practically a standard practice now. I do not know of anybody that is using the tandem system now. No one is building a plant with a tandem system in it.

Jan 1, 1930

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position in sales department is open for a mining engineer with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions. No. 2. A large company manufacturing mining machinery has an opening in one of its Western agencies for a young mechanical engineer who has had some experience in designing along general machine shop lines, and who is familiar with cost systems. No. 3. A large university desires to secure a prominent metallurgist for a vacant professorship in metallurgy. No. 4. Opening at a mine in New Jersey for a technical graduate to begin work as chairman on the surveying squad. Salary $50 per month to start. No. 5.

Jan 11, 1913

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,' an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,' an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

Since the composition and structure of the beach sand concentrates correspond so closely to what would be expected of ilmenites that have been altered by oxidation and leaching, there is no reason to postulate the existence of the hypothetical compound, arizonite, to account for the composition of titaniferous beach sand concentrates. The four concentrates studied are examples of the different products that can result from various degrees of alteration of primary ilmenite. CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO², as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilrnenite.: It has also been referred to as arizonite because in chemical composition it resembles an Occurrence in in which was described by Palmer' in 1909. The chemical composition of Palmer's arizonite corresponded closely to the formula Fe²O³ . 3TiOs. From approximate measurements of crystal angles on a large imperfect crystal with rounded faces, the

Jan 1, 1955

By E. A. Nesbitt

THE important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent- magnet properties. In recent years great, advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,l an alloy of iron, cobalt, and molybdenum, the various iron- nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be .rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat- treatment, and at this time the ductility A of the alloy disappears. If the cast alloy is heat-treated without cold-working the magnetic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X l06. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold- worked in such a manner as to improve its energy product substantially, it is called Vicalloy II. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone In a variety of forms Vicalloy I or II is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age- hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of com- position are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. PREPARATION AND PROPERTIES OF VICALLY I The alloys were usually cast in graphite molds into bars ¾ in. in diameter and

Jan 1, 1946

By T. Sterry Hunt

I have in a previous communication called the attention of the Institute to the geognostical relations of the crystalline iron ores belonging to the Eozoic racks of North America, at which time I noticed (1) those associated with the gneisses of the Laurentian series, (2) those of the crystalline schists of the Huronian, as seen in Northern Michigan and in many localities along the Appalachians; (3) those of Southeastern Missouri associated with petrosilex porphyries and schistose rocks, and presumed to be nearly of the same age with those of the Huronian schists; and (4) the highly titaniferous ores of the Norian or Labradorian series from Essex County, N. Y., and from various parts of Canada. It may here be remarked that, although the presence of titanium is most marked in the Norian ores, this objectionable element is sometimes found in the schistose ores of the Huronian, and to a lesser extent in certain Laurentian magnetites. The ores of each of these geological divisions have their individual peculiarities, which serve to distinguish them to such a degree that the magnetites and specular ores of the Laurentian are as dissimilar to those of the Huronian as are the crystalline silicated rocks of the two series. As it happens that these mineralogical dissimilarities correspond to diflerences in composition and in adaptability to different processes of manufacture, which, in the present condition of the iron industry, are objects of special consideration to metallurgists, it will be seen that these geognostical distinctions become of great practical importance. During the past year I was desired by the Geological Commissioners of Pennsylvania to devote a few weeks to certain geological studies in the eastern part of the State, in the course of which I was enabled to make, with regard to its crystalline iron ores, some observations to which I desire to call the attention of the Institute. I may mention, in passing, that the great South Mountain belt, from the Schuylkill to the Delaware, is composed of Laurentian rocks, in which are found the characteristic ores of the series like those of the Highlands of New Jersey and New York, and of the Adiron-