Search Documents

By J. W. Richards

Plating iron with copper has received great attention from practical and scientific men, but, aside from the deposit secured by immersion of iron in copper salts, by electro-plating, or by welding together thin sheets of iron and copper, these efforts have met with no success. Failure of these efforts, in the production of copper plating, has been due to the fact that the conditions normally and necessarily present in the plating operation are antagonistic to the production of copper-plated iron. In most, if not quite all of them, a bath of molten copper has been used. The temperature of a molten copper bath is so high that the iron becomes oxidized before it can be immersed in the molten copper, and unless a protective flux for the molten copper is used, the surface of the copper will become oxidized, and, in any event, the plated iron will oxidize immediately on its being withdrawn from the molten bath. I recently had the pleasure of visiting the works of The Metals Plating Co. at Elizabeth, N. J., where I witnessed the plating of iron sheets with copper by a new process.l The plating metal is applied to the sheet in the form of a liquid mixture by means of rolls, such as inking rolls. The sheet, after being coated with the mixture, is automatically carried forward and deposited on a link-belt conveyor, which carries it through a furnace maintained at a temperature well above that of molten copper. The basic principle involved in this method lies in the application of the plating metal to the sheet while the sheet is cold and then melting the metal in place on the sheet under conditions which are favorable to the formation of the plating. Plating Mixture The liquid plating mixture is composed of either copper oxide or finely divided copper, or a mixture of both, ground to the consistency of a light varnish in a crude oil having an asphaltic base, of a specific gravity of from 14" to 16' Be. The plating mixture which gives the best results

Jan 1, 1919

By A. Sutulov

The segregation process, an alternative to benefi-ciation of oxidized and mixed sulfide-oxide copper ores, is studied here with particular emphasis placed on time, temperature, and coke and salt percentage factors. The results show that in a segregated charge, the copper assay of the coarsest fractions normally is of the same order as the copper assay of the tails obtained from grinding and flotation of the same charge. This observation suggests the possibility of limiting or even eliminating the grinding step from the flowsheet of a segregation plant. The segregation process, which offers an alternative to beneficiation of oxidized and mixed sulfide-oxide copper ores, was discovered in 1923 by Moulden and Taplin1,2 who were attempting to apply the Perkins process3'4 to a Chilean ore from the Sagasca mine. After a number of investigations and pilot plant tests,'-' the segregation process became a successful industrial operation.'r9 The process aroused considerable interest in Chile because of the existance of large reserves of oxidized copper minerals which could not be treated by conventional hydrometallurgical methods because of the high consumption and prohibitive cost of sulfuric acid. During the last two years, the Mineral Dressing Dept. of the Institute de Investigaciones Tecnology cas of University of concepci6n (Chile) has carried out a test program on 23 different ore samples representative of the national territory. These tests were carried out on a semi-continuous and batch scale with a rotary, automatically controlled and gas-fired furnace (supplied by Bartlett and Snow, Fig. 1). The results of these tests indicate that out of the 23 samples 20 can be successfully treated by this process with recoveries of copper ranging from 85 to 95%.10,11 The purpose of this paper is to treat some specific problems related to the segregation process. TIME AND TEMPERATURE FACTORS Time and temperature of calcination play an important role in the segregation process. When moderate salt and coke conditions were maintained (each of reagents was added in the quantity of 1 — % wt), systematic testing easily demonstrated the influence of these two factors on segregation and flotation recovery. The pertinent results are summarized in Fig. 2. To determine what specific changes the segregation process made on the ore, the samples, segregated at 700°C for different periods of time and under standard conditions, were granulometrically analysed and

Jan 1, 1963

By Lyall Zickrick

As a result of the studies on recrystallization and crystal growth made in this laboratory, certain theories have been developed. These are expressed briefly in a paper by Dean and Hudson.1 One of the principal points brought out in that paper is that in the deformation of a crystal, the energy supplied is distributed to the atoms of the lattice, probably by the forced formation of molecules. It is found that a Maxwellian distribution of the energy among these atoms will account for the grain growth at various temperatures. According to such a distribution the number of atoms with energy above a certain critical value, E, necessary for recrystallization at the absolute temperature T is given by n Ne(-E/kT) where N is the total number of atoms. It is apparent that if this line of reasoning is correct, a metal which has been cold-worked and reheated to a temperature below that of complete annealing will have the atoms with the higher energy recrystallized, that is, reduced to normal energy and there will remain only atoms below a certain energy. If this metal is again cold-worked the peak in the number-energy distribution curve will be displaced toward the regions of lower energies, that is, higher temperature of recrystallization. By a repetition of this process the position of this maximum and hence the recrystallization temperature of the metal could be raised considerably. In order to' check this theory, experiments have been made on copper wire. The wire was drawn from 1/4-in. rod to 22 B & S gage and then sample lots were annealed at 400 and 220° C., respectively. The wire annealed at 400° C. gave an elongation of 34 per cent., whereas that annealed at 220° C. gave only 23 per cent. These wires were then drawn by identical practice to 34 B & S gage and the elongation determined after an anneal of 3 mm. in an oil bath held at various temperatures.

Jan 1, 1927

By J. H. Smith, H. W. Paxton

ALTHOUGH many structural and kinetic investigations have been made for alloys of iron and nickel, only meager data exist from thermodynamic investigations. The purpose of this note is to estimate the free energy of the Fe-Ni solid solutions from thermodynamic data available for ternary alloys containing iron and nickel. The lack of a description of the thermodynamic behavior for the Fe-Ni system has required the structural and kinetic analyses of the system to assume some form of solution behavior, usually regular, e.g., the mar-tensite transformation analysis of Kaufman and Cohen, 1 consistent with the limited thermodynamic data. Indications that this system could exhibit ideal solution departures might have been suggested by the large deviations from additivity rules observed in the density and lattice-parameter measurements of Jette and Foote2 who interpreted this in terms of possible solute-solvent interactions. Later Turkdogan et al. 3 and more recently Ward and wright 4 found a minimum in the graphite solubility in liquid Fe-Ni solutions near the concentration of FeNi3 with deviations from linearity persisting at all concentrations. This was interpreted by Ward and wright4 to indicate negative heats of solution and was suggestive of short-range ordering. The infinitely dilute activity coefficient of carbon (?oC) was also observed by smith5 to pass through a maximum near the FeNi3 concentration in Fe-Ni solid solutions. Recent investigations of the liquid solutions over the entire concentration range by Zellars et a1.' and Speiser et a1.," using vapor-pressure determinations, revealed both negative departures from Raoult's law and a nonregular solution behavior. The solid alloys have been studied by Oriani 8 and Kubaschew-ski and von Goldbeck6 employing gaseous H2/H2O equilibria with Fe and FeO. Both investigations were in substantial agreement, indicating very small departures from ideality. However, Oriani observed the formation of Fe3O4 (instead of FeO) at XFe= 0.441 which severed the equilibrium and precluded experimental investigation of the nickel-rich alloys. Heat-capacity and heat-content measurements have been evaluated by Montgomery10 and found generally unsatisfactory for gleaning thermodynamic information. This is due to the unknown final states of the alloys caused by the interference of the martensite transformation on cooling iron-rich concentrations and superlattice formation, magnetic transformation, and the varied heat treatments used by investigators of nickel-rich concentrations. As an alternative to the experimental difficulties, indirect estimates of the solid-solution behavior have been made by Fleischer and Elliott11 and Smith et a1.12 From their measurements of the solubility of Fe-Ni alloys in liquid lead, Fleischer and Elliott calculated the nickel activity (aNi) (and integrated for aFe) by assuming: 1) liquid lead has no solubility in solid Fe-Ni alloys, 2) Henry's law is obeyed throughout the liquid lead-rich phase (0— 12 at. pct Nil, and 3) Henry's law constant is independent of relative iron and nickel concentrations. The estimate of Smith et a1.12 was obtained

Jan 1, 1964

By W. J. Taylor

It is, perhaps, more important to put on record the particulars of experiments that are derided failures than those that are successful, as those of the latter class are certain to live, while the former may be lost sight of in a short time, and repeated by others. TO this end, I propose to give the particulars of a straight or no-bosh furnace just tried at the Chester (New Jersey) works, which was such a decided failure as to leave no doubt of the plan being wrong, and determining the necessity of a bosh of some kind, as of old. Some experiences during the past year led me to suppose that the bosh or belly of a furnace was unnecessary, and that the contraction of the walls toward the bottom for the stock to wedge in, in its descent, facilitated dirty walls and scaffolding; hence, irregularity and high fuel. I concluded, however, that a very shallow bosh for a skew-back support to the stock would be necessary, and that the proper place for this was in the tuyere-section, beginning just below the tuyeres and ending just above them, where there is nothing in the solid state but fuel, which is consuming, and no slipping or travel of stock takes place. The cubical capacity of a furnace of this design would necessarily be much less than in the old style, unless it was made very much higher. But I assumed that the loss of room for reduction could be overcome by making the size of the ore and stone charged much smaller, so that the gases would act more quickly. The next point was, what should be the size of the shaft, crucible, tuyere-circle, and tunnel-head for a given quantity of air? My first design was 12 feet diameter of shaft for 7000 feet of air, with a 9-foot crucible and 8-foot toyere-circle. This I soon reduced to 8-foot shaft diameter, which I concluded was large enongh for economical work, if regular travel of the stock on the walls could be maintained. I consulted with a number of experienced furnacemen and furnace-engineers, and the plan was well thought of by many of them; and, as I had also some offers of financial aid from them toward the risk of trying the experiment, my firm concluded

Jan 1, 1885

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By D. E. Wolfson, D. A. Reynolds, F. W. Smith

IN 1948 the U. S. Bureau of Mines began a three-phase program to evaluate the extent and quality of U. S. coking coal: 1) a factual appraisal of known recoverable reserves in beds of mineable thickness, 2) a study of preparation characteristics, and 3) a study of carbonization properties. A previous paper presented the methods used in assessing reserves.' Although this investigation is only partly completed, data on coking properties of the Pittsburgh district coals are now available. The results are presented in this article. When coals are selected for manufacture of metallurgical coke more factors must be considered than for any other major use, as no basic industry requires coal of such high quality and uniformity. This is particularly true in the Pittsburgh district, where blast furnace practice is based on use of cokes from high quality coals. Although it is true that inferior coals are carbonized in other industrial areas, both here and abroad, the Pittsburgh coals are the best economically obtainable in the required tonnages, even though they are not the most desirable for metallurgical use. In the general evaluation of suitability of coals for coke making, particular attention is given to: 1) reserve, 2) ash and sulfur content, 3) inherent properties of forming strong, well fused coke, 4) expanding characteristics, and 5) blending properties. Items 1 and 2 are covered in detail in the first two phases of the survey, and coking behavior is considered in items 3 through 5. Problems is Coal Evaluation: Although not all coal beds of immediate or potential use to the coking industry in the Pittsburgh area have been tested for their coking properties, enough tests have been made to permit certain generalized statements. Virtually all the coals that will be used in this district are from the Appalachian region, and except for high oxygen coals from outcrops or stripping operations, they are coking coals. Hence the evaluation problem is not so much that of distinguishing between coking and noncoking coals as attempting to measure quantitatively differences in the coking and expanding properties of the better coking coals. Quantitative differentiation between good coking coals, is complex, since differences in their coking abilities are frequently of about the same magnitude as the precision of the test. Small-scale tests are generally unsuitable for measuring these slight differences, and there has been gradual acceptance of pilot-scale tests. Test Methods Employed: All the data reported here were obtained in two units known as the Bureau of Mines-American Gas Association (BM-AGA) carbonization apparatus and the sole-heated expansion oven. The BM-AGA unit, which consists essentially of a cylindrical steel retort about 18 in. diam and 26 in. high, carbonizes enough coal (180 lb) to allow evaluation of the coke by standard methods of the American Society for Testing Materials. The BM-AGA carbonization procedure and methods of testing the gas, liquid, and solid products have been described.' Expanding characteristics of the coals were determined in the sole-heated expansion oven," wherein the coal charge, heated from the bottom only, is carbonized under a constant applied force and the linear expansion or contraction is measured. Although results in this oven have never been quantitatively correlated with the expansion behavior of coals in conventional slot ovens, they are useful in assessing expansion behavior. In this report discussion will be confined to results obtained from these pilot-scale units, although the following data are available for most coals: proximate and ultimate analyses, free swelling index, agglutinating value, and plasticity. Sources of Coals Tested: In selection of coals for coke manufacture, economic considerations are as important as quality, and each coke plant balances these two factors to meet requirements of the most satisfactory coke at lowest price. Although these economic factors may in some instances outbalance small differences in coke quality, they are usually specific to each coke plant and cannot be given in any general statement. Recognizing that coal and plant operating costs are beyond the scope of the survey, the USBM evaluates the coking quality of various coals without regard to their competitive economic status. For the purpose of this article, coals of interest to the Pittsburgh district are arbitrarily defined as

Jan 1, 1958

The primary purpose of the Institute is to advance the technologic and engineering arts embraced by it through interchange of knowledge. This can best be clone by the presentation and discussion of technical papers by its members. Short practical papers are especially welcome. An author should always satisfy himself that his material is of a quality that will he a credit to him and to the Institute. The preparation of a good paper frequently leads to a reorientation of the author's thoughts, and publication contributes much to the professional standing of the author. Members are urged to submit papers presenting the results of their work. Attention to the following suggestions will greatly further the prompt and efficient handling of manuscripts. 1. SUBJECTS: The subject must be within the field of the Institute. Original work, the results of field, plant, laboratory or theoretical investigations, new views on old but important problems and occasionally reviews of timely and important subjects of wide interest to our members may constitute the basis of a paper. The mere fact that the work is original does not necessarily justify publication: it must be of a substantial nature, of value to a reasonable number of our members and worthy of permanent record. It is seldom desirable to subdivide the results of a single research for publication in a variety of journals. Previous publication is usually a bar to acceptance. If any part of your paper has been published elsewhere and you regard repetition as absolutely necessary please so state in your covering letter. 2. CONSTRUCTION: Papers should be clearly and concisely written in good English. Care in this regard ensures wider reading and the saving in space permits the Institute to publish more papers. It is the experience of the Papers and Publications Committee that most papers can he improved by condensation. "Readers" who are asked to recommend acceptance or nonacceptance put particular emphasis on the length of the paper and the elimination of unnecessary or any extraneous material. The terminology and units employed should be those current in the particular field. An examination of Institute publications will afford useful guidance in such matters. Webster's New International Dictionary, 1935 edition, is the Institute's authority for spelling and style. Various abbreviations are used habitually; for instance, lb., pound; bbl., barrel or barrels; ft., foot or feet; hr., hour or hours; in., inch or inches; Fig. 1 but Figs. 2 and 3.

Jan 1, 1946

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By P. K. Currie, J. V. Walters

Solution mining of magnesium salts (Carnallite and Bischofite) is taking place near Veendam, in the northeast Netherlands. The magnesium salts are used for the production of magnesia sinter, used as a base material for the manufacture of refractory bricks for furnaces. This paper gives, first, an introduction to the operational procedure followed in Veendam, with the emphasis on some of the unique aspects, and then discusses rock-mechanical aspects of the cavity behaviour. The creep behaviour of magnesium salts is described, and Finite Element calculations on cavity stability and potential surface subsidence are discussed.

Jan 1, 1985

By R. H. Tien

This paper presents an analytical solution of the problem of freezing of a semi-infinite slab with constant surface temperature; in this analysis accoz~nt is taken of the heat evolution during the solid-state transformations in the frozen skin. The regions where transformations occur are treated as plane isothermal heat sources; i.e., the rates of transformations are assumed to be infinite. In the model considered, three plane heat sources are assumed to be present in the frozen solid. The solution yields the temperature distribution in the solid, the rates of movement of the heat sources , and the rate of movement of the solidification front. It is shown that, although the sum of the heats of transformations in the solid is about 20 or 43 pct of the heat of fusion of iron or manganese, respectively, the effect of the heat evolution in solid-state transformations on the rate of solidification is insignzficant. IN several recent mathematical studies of solidification of liquid metals'-3 no account was taken of the heat evolution accompanying the solid-state transformations. In the case of, for example, steel, there are several phase transformations 6 -y, y -a, and the magnetic transformation. Whether or not a significant error is introduced into the mathematical simulation of solidification processes by the omission of the heat effects associated with these phase transformations is not known. The purpose of the present study is to investigate the effect of these phase transformations on the temperature distribution and the rate of solidification based solely on the heat transfer point of view. That is, for the sake of simplicity, freezing of a pure metal with solid-state transformations will be considered. The mathematical model which represents the present problem includes four moving heat sources representing freezing and phase transformations, 6— y — a — ferromagnetic. The thermal properties such as conductivity and specific heat, and so forth, are different from one phase to the other. But they are considered to be uniform over any particular phase. The usual Fourier heat flow law is employed. The concept of conservation of energy is applied at every heat source in order to estimate their rate of movement. The temperature distribution in the solid and the positions where transformations occur are expressed analytically in terms of error function solutions and four coefficients which are determined from four nonlinear algebraic equations. These coefficients can be calculated either by trial and error or by any numerical method. MATHEMATICAL ANALYSIS Fig. 1 is a schematic diagram showing the zones of different phases 1, 2, 3, and 4 in the solidified portion of a semi-infinite pure liquid metal. The heat is subtracted from the system at x = 0 which is maintained

Jan 1, 1968

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By Brahm Prakash, R. Schuhmann

Maurice Rey—It may be interesting to note that depressing effects can also be obtained from cyclic compounds other than dyes. One such compound which is a dispersing agent for carbon, pigments and other compounds is known in France by the trade name "dispergine" and in the United States by the name of Lomar P W (Jacques Wolf & Co.) Dr. Rey admits that the compound is not very selective and is similar in its action to starch and dextrin.

Jan 1, 1951

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By E. A. Anderson

IN another paper1 the writer has shown that the low permissible maximum fiber stress in a loaded zinc sheet demands a much closer support spacing than is used for steel. The limiting fiber stress in 13-gage (0.032 in.) sheets having a 1-in. depth of corrugation was found to be about 5000 lb. per sq. in. on a 37-in. span under a load of 40 lb. per sq. ft. Corrugated steel sheets are commonly laid with spans varying from 48 to 60 in. In order to increase the span in 13-gage zinc to 54 in. (a common spacing) the metal must be capable of withstanding, under long-continued loading, a maximum fiber stress of about 10,000 lb. per sq. in. This is known to be impossible with unalloyed zinc. In this paper the writer describes a series of experiments leading up to the development of an alloy capable of safely sustaining this fiber stress. The effect of alloying on the slow creep of zinc was studied by means of static tensile tests, accurate determinations of apparent elastic limits and finally by means of loading tests on full-size roof sections. Two industrial buildings roofed with alloyed zinc sheets on spans involving fiber stresses in excess of 10,000 lb. per sq. in. have been under observation for over two years without signs of sagging.

Jan 1, 1929

By W. D. Robertson

A considerable quantity of experimental data is available on the effect of time, temperature, work-hardening and composition on the mechanical properties and corrosion resistance of aluminum alloys. There is, however, little unity of purpose or generality in most of the studies and, because the number of variables is large, the results often are not applicable to the problems that arise in practice. Furthermore, the customary expression of the effect of different variables as separate curves or as three-dimensional diagrams with time, temperature and the dependent variables as coordinates, renders the task of selecting the optimum time and temperature of precipitation treatment, with respect to their simultaneous but unequal effect on the various properties, exceedingly difficult. The introduction of precipitation treatments to raise the yield strength of 24S-type alloys has created a need for a method of correlating and summarizing the effect of time and temperature on the mechanical properties and susceptibility to intercrystalline corrosion. Correlation is particularly desirable because the choice of time and temperature is of necessity a compromise to achieve the best possible combination of properties, and the optimum conditions cannot be accurately specified unless the data are in a form in which the alternatives can be readily compared. Therefore, the work described here was undertaken to find a common relationship that would be capable of expressing the effect of precipitation time and temperature on the various properties and by means of which the relative effects could be correlated and their interpretation facilitated. REVIEW OF PREVIOUS WORK In connection with an investigation of the interrelation of age-hardening and creep performance of nickel-silicon-copper alloys, Jenkins and Bucknall1 demonstrated that the time required to attain maximum hardness and tensile strength could be expressed by a relationship of the form: t = K. 10m/T (I) where t is the time in hours and T the temperature of aging, expressed in degrees absolute, and m and K are constants. They also pointed out that this expression is analogous to that which describes the change of the diffusion coefficient D with temperature; namely, D = Ae-Q/RT (2) Later, Cohen used this relationship in studies of the mechanism of age-hardening of a silver- rich copper alloy2 and of duralumin. 3

Jan 1, 1945

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By W. O. Hotchkiss

Rock exposures are usually a very small part of the surface area in any mining district and the prospector and geologist must base their deductions as to the area, extent, and structure of various formations upon exposures that seldom form 5 per cent. of the area studied. Most often, outcrops form less than 1 per cent. of an area, so that exploration for mineralized contacts or mineral-bearing formations necessitates drilling, test pitting or tunneling, shaft sinking, and other underground work. In these days of high costs any method that will give definite facts regarding rock? obscured by soil or other material should be used to the greatest possible extent. In the early days of the Lake Superior iron districts, mines were located in the few places where ore was present in outcrops. Later, larger orebodies have been found, in depressions, obscured by soil and other foreign material. Mineralized rocks are oftentimes more weathered, softer, and more easily eroded than unmineralized rocks. It is quite natural, therefore, to expect that such orebodies (particularly where large enough to influence erosion in former physiographic conditions) should lie in depressions and be obscured by later debris. It is not difficult to believe that the history of the development of Lake Superior iron mining may be duplicated in other mining districts, that even larger orebodies than those first mined may be found in areas where the rock exposures, which led to original discoveries, are few or lacking. The chief properties of rocks that can manifest themselves through an obscuring cover are magnetism, electrical effects, radio-activity, gravity, and sound transmission. All of these have been used, to a small extent, to tell us a few things about what lies below the surface that we could not otherwise determine, but none has been used so long and so widely as

Jan 1, 1923

By J. C. Humbert, J. F. Elliott

The solubility of nitrogen in liquid pure Fe, Cr, and Ni, in liquid Fe-Ni, Fe-Cr, and Ni-Cr alloys and Fe-Cr-Ni alloys, has been measured by the Sieverts' type apparatus between 1500° and 1800°C. Tabulations and graphs of the solubility data and activity coefficients are shown. Heats of solution are reported. Interaction coefficients of the several elements in Fe. Cr, and Ni ave also reported. THE solubility of a gas in a liquid metal is usually measured by either the quenching technique or the so-called Sieverts' method. In the quenching method, 1-3 the melt is equilibrated at the desired temperature and pressure with the gas phase having a known fugacity of the gas being studied. The melt is sampled and the sample is quenched and analyzed chemically for its gas content. In Sieverts' method the melt is contained in a closed chamber. The apparent volume of this chamber, i.e. the "hot volume," is usually determined by introducing a known quantity of an inert gas having very closely the same physical characteristics as does the experimental gas. Alternatively, the experimental gas is used with an inert specimen having the same general physical characteristics as does the experimental melt. Subsequently, the experimental melt is equilibrated with the experimental gas by introducing a known quantity of the gas into the calibrated chamber. The solubility of the gas is obtained from P-V-T relationships. The quenching method suffers from' the limitation that some gas may be gained (as in the case of Cr-Fe alloys) or lost (as in the case of Fe-Ni alloys) during solidification and cooling of the sample. With Sieverts' method sampling and analysis are unnecessary. However, errors can result from the difficulty of determining accurately the "hot volume,"

Jan 1, 1961

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970