Search Documents

By Ernest A. Hersam

The advantages of the tri-axial diagram in representing the composition of slags and silicates are well appreciated by many metallurgists. Prof. H. M. Howe* has pointed out the application of a fourth variable, in connection with the diagram, and has called attention to the usefulness of the general systern of tri-axial representation. In the discussion of Prof. Howe's paper, Mr. Firmstone† indicated how certain distances could be measured directly by projection. Prof. R. H. Thurston,‡ as early as 1877, had made use of a typtic model and of triangular diagrams, with contour-lines, rekrresenting varying physical properties corresponding to varying chemical composition. Still earlier, Prof. J. Willard Gibbs§ had used the diagram in similar work; and other scientists were thought by him to have preceded him in its use. During the period of nearly a quarter-century, following these early publications, there has been an ever-increasing use of graphic methods in numerous branches of scientific work, stimulated, in part, by the possibility of representation by three co-ordinates upon plane-surfaces. Yet the number of possible co-ordinates for graphic representation has always been, and always must be, insufficient to express many facts which are shown mathematically; while, without graphic representation, the involved nature of mathematical expression often fails to facilitate and promote research. The coming into use, therefore, of the fourth co-ordinate, permitting representation by four variables, marks but the beginning of some lines of research which could not well advance without this aid.

Jan 1, 1902

By Howard Smith

OF late considerable experimental and, theoretical interest has been shown in the rates of transformation from a single phase, usually a supercooled solid solution, into one or more phases. Such reactions may involve both diffusion and transformation of the major constituent, as in iron alloys, or it may simply involve diffusion, as in superstructure forma-tion and in age-hardening systems. Most of the work has been confined to ferrous alloys1-9t although two investigations have been made on copper alloys10,11. That such work may be of considerable, practical importance has been demonstrated by Bain12, by the workers at the Kaiser Wilhelm Institut fur Eisen-forschung13,14, and by the everyday use of precipitation and age-harden-inn principles15. Experiments in this country have generally followed Davenport and Bain's technique of rapid supercooling followed by isothermal treatment. In Germany16,17 the work has been extended to the study of the influence of accurately controlled and measured rates of cooling. The work on steel indicates that there are two subcritical temperature ranges where reaction starts sooner after quenching and proceeds at a more rapid rate than at other temperatures. At subcritical temperatures above Ar" where reaction is dependent upon atomic migration there is a period of time of which the length depends upon the alloy content and the temperature, before which no reaction has been detected. Daven-port and Bain1 find that different sorts of atoms in solid solution in gamma iron affect the length of this "prereaction" period differently, manganese

Jan 1, 1935

A mine that staggers the imagination is Chuquicamata, the granddaddy of them all. In 1968 production exceeded 300,000 tons of copper. Production began in 1915 and mining proceeded solely on oxide ores until 1953 when the first treatment of sulfides began. Today the company has mined about 1.2 billion tons of all types of material since inception. The accelerating rate of output can be gauged by the comparable 1946 figure of production-to-date which was 350 million tons. No single mine comes close to touching Chuqui for productivity at its high annual metal yield mining only 90,000 tpd of ore at the luxurious waste-to-ore ratio of 0.6 to 1. However, the complexity of the operation is enormous and the experience required to synchronize the various processes is masked by normal operations and only becomes apparent in times of emergency such as when the slide took place in the pit in February.

Jan 11, 1969

By Wilbur Jurden

THE writer's first experience with a nonferrous reduction plant of great magnitude was at the Washoe reduction works of Anaconda some 35 years ago. Here was a plant which had been planned with remarkable skill and foresight considering the time and the state of development of copper-plant practice in the year 1902. The designer utilized topography to fullest extent to provide proper sequence of operations and, what is most remarkable, to leave adequate space for future developments, most of which at that time were unknown. However, the practice then was to locate the various units of the reduction works at the most advantageous points of the existing terrain with little regard for tramming or other auxiliaries and then connect these various units by the essential trackage, conveyor systems, piping, etc., as the need developed. This occasionally led to undesirable track arrangements, sharp curves, and steep grades, especially when it became necessary to extend various portions of the plant. Conveyor systems also became rather complicated, running as they did at various angles, and such items as piping and electrical distribution were often found to be in the wrong place, entirely inadequate in size, or awkwardly arranged for any kind of extension. This condition was not peculiar to Anaconda, for all copper plants at that time were built in the same manner and it was the constant association with these difficulties which, in the year 1925, influenced the layout of the Andes Copper Mining Co. plant. In that plant all trackage was laid out straight and level, all conveyors at right angles to each other with minimum length and number of transfers. All buildings were placed parallel and the main structures were complete for all purposes so that auxiliary buildings and dog houses would not be added later. Piping and electrical work was provided for in the original layout and carefully designed to avoid additions and alterations, and careful study given to every movement of material throughout the entire plant so that it would be accomplished with the least possible effort. Naturally it was hardly expected to attain all these objectives perfectly but our efforts did succeed in creating a plant which was unique and outstanding for its time-1927. It was also most gratifying to find that these design principles contributed to considerable savings starting right in the drafting room, carrying through the construction and ultimately yielding savings in operations and manpower. Not only that, but such a plant gives the observer an impression of symmetry and order, is more attractive to the workmen, and unquestionably eliminates many accident hazards. However, the Andes plant buildings were fitted to the existing terrain instead of having terrain created to fit the buildings-an item which we found advantageous to correct on the next large plant. At Morenci in 1939, all of the desirable features of the Andes plant such as parallel buildings, etc., were incorporated; but we went one step further-power shovels were brought in to make the terrain fit the reduction works. The result at Morenci is well-known and needs no elaboration here, but the success achieved by the design methods used for this and previous plants naturally influenced and guided the layout of the Chuquicamata sulphide plant which is the largest yet conceived. Chuquicamata Plant Design At Chuquicamata several factors not encountered previously complicated the problem to a great extent. The most desirable location for the smelter would allow smelter gases to blow directly into the open-pit mine already producing 60,000 tons of oxide ore per day and employing 1550 men. This, of course, would be a serious condition and, therefore, we were forced to move the smelter to a less desirable location but followed our previous experience at Morenci and made the terrain fit the job. The most difficult problem, however, was the provision for receiving various types of ore both by rail and conveyor. These consisted of: 1-Sulphide-bearing residue from the stockpile from which oxide copper had previously been leached. 2-Sulphide-bearing residue coming direct from the leaching vats. 3-Sulphide ore crushed at the existing crushing plants and hauled to the concentrator in cars. 4-Sulphide ore from the new crushing plant adjacent to the concentrator. 5-Sulphide ore obtained

Jan 1, 1952

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.'" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase 'Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By J. K. Gustafson

MEASURED in terms of ore tonnage, the New Quebec and Labrador iron ore fields promise to rank with the greatest iron ore districts of the world. -- Over 400 million tons of high-grade ore for direct shipping have been discovered to date. Much greater amounts of lower-grade beneficiating ores are indicated by outcrops. Many hundreds of square miles of iron formation await testing.

Jan 6, 1953

"Power is transmitted to Butte, a distance of 130 miles, over two separate lines running parallel on the same right of way.The transmission line embodies the most approved ideas in construction. The conductors are No. O. B. & S. gauge, hard drawn copper strand. The insulators are of the suspension type, each insulator consisting of six units, 10 inches in diameter. The insulators will stand a wet test of over 300,000 volts, and were selected after long and careful tests by the company's engineers. The wires are carried on steel towers of four-legged, single crossarm type, manufactured by Milliken Bros. The three conductors are suspended in a horizontal row from the crossarm, and there are no transpositions in either line. Above the power wires and symmetrically located are two galvanized steel strands, Vs-inch in diameter, grounded at each tower, which serve as a protection against lightning.The distance between towers in level country is 600 feet. In mountainous country, however, the spans are irregular in length and spans of 1,500 or 2,000 feet are common. The longest one in the line is that crossing- the Missouri River and is equal to 3,034 feet. The length of this span is such that a person standing at one end of it can sec the wires go off and vanish into space, while the tower at the other end is barely visible to the naked eye on a clear day. The towers at one end of this span arc shown in the accompanying photograph. The line starts at an elevation of 3,200 feet, rises to an elevation of 8,200 feet as it crosses the Continental Divide, and again descends to 6,100 feet, the elevation at Butte.Quantity of coppc1· in transmission line, 1,330,000 pounds.Number of towers, 2,-1-00.Steel used in construction, approximately, 2,-1-00 tons."

Jan 1, 1913

By I. N. Zavarine

The present paper is a continuation of the work on the relationship between the magnetic and the phase transformations in carbon steels during quenching. An account was given by the author in a previous paperl† of an investigation of this relationship during a continuous quench. The experimental difficulties then encountered prevented a conclusive proof of the existence or absence of such a relationship. The conclusions of the previous paper were derived indirectly. The present paper deals with the same problem, but the method of attack is modified. The technique developed by Davenport and Bain2 in their well-known study of austenite transformation at subcritical temperature was adopted in the present investigation. They have shown that the austenite to martensite transformation can be caused to proceed at a relatively slow rate by quenching steels into a hot metal bath. Slowing down of the rate of transformation, together with an observation by Lewis3 that a eutectoid steel can be preserved in the nonmagnetic state by such quenching, pointed out a possibility of a study of both transformations under more favorable conditions than previously described. The preliminary steps were connected with the technique of the hot bath quench. To study this phase of the present work a modification of the apparatus previously described' was used. The modification consisted in the use of a hot quenching bath instead of brine, and in fixing the secondary and the primary coils of the apparatus in a stationary position in and around the bath. Tubular specimens, as in the previous investigation, were heated in a suitable furnace to a temperature in the austenitic range for the given steel and then were dropped into the quenching apparatus. The quenching bath was heated to a series of temperatures within the probable range at which the austenite to martensite transformation was expected to proceed at the slowest rate. Observations

Jan 1, 1936

By I. N. Zavarine

The present paper is a continuation of the work on the relationship between the magnetic and the phase transformations in carbon steels during quenching. An account was given by the author in a previous paperl† of an investigation of this relationship during a continuous quench. The experimental difficulties then encountered prevented a conclusive proof of the existence or absence of such a relationship. The conclusions of the previous paper were derived indirectly. The present paper deals with the same problem, but the method of attack is modified. The technique developed by Davenport and Bain2 in their well-known study of austenite transformation at subcritical temperature was adopted in the present investigation. They have shown that the austenite to martensite transformation can be caused to proceed at a relatively slow rate by quenching steels into a hot metal bath. Slowing down of the rate of transformation, together with an observation by Lewis3 that a eutectoid steel can be preserved in the nonmagnetic state by such quenching, pointed out a possibility of a study of both transformations under more favorable conditions than previously described. The preliminary steps were connected with the technique of the hot bath quench. To study this phase of the present work a modification of the apparatus previously described' was used. The modification consisted in the use of a hot quenching bath instead of brine, and in fixing the secondary and the primary coils of the apparatus in a stationary position in and around the bath. Tubular specimens, as in the previous investigation, were heated in a suitable furnace to a temperature in the austenitic range for the given steel and then were dropped into the quenching apparatus. The quenching bath was heated to a series of temperatures within the probable range at which the austenite to martensite transformation was expected to proceed at the slowest rate. Observations

Jan 1, 1936

By AIME AIME

AT the Morenci branch of the Phelps Dodge Corporation, of which Frank Ayer is manager, several new types of machines that have been developed by Charles Mitchell, shop foreman in the drill steel shop, invite comment for their time and labor-saving qualities. Foremost of these is an adjustable gage-block and gaging device for attachment to drill-sharpening machines, developed and patent applied for by Mr. Mitchell. It replaces the blocks on the standard Ingersoll-Leyner drill steel sharpener No. 5. Features of the device are gage blocks with a flat surface which can readily be removed when worn and planed in any flat planer; blocks that can be adjusted with a templet to give a far more accurate gage than was formerly possible; and a center stop that is adjustable and can be accurately set to center any standard size drill steel.

Jan 1, 1930

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

By G. D. Tranter

The importance of ladle and teeming practice and its relationship to the yield and quality of the product has focused considerable attention on this phase of open-hearth operation. Inherently bad steel cannot be perfected by manipulation during teeming, but through the proper handling of "off heats" serious losses, which in many cases arise, can be greatly minimized. Conversely, good steel can be ruined as a result of poor workmanship in the pit, and rendered unsuitable for application to orders where exacting surface and physical requirements are essential. Sufficient evidence has been secured to warrant careful investigation of pit operations when an abnormal number of basic defects develop in the semifinished product or are found on the inspection table. This paper is written from the standpoint of the problems involved in making satisfactory ingots for sheet rolling. Furthermore, since rimming steel is almost universally used for manufacture of sheet, the data presented herein refer particularly to that type of steel. Going back some 30 years in open-hearth history, the word "pit" properly described the hole into which the ladle was lowered to receive the metal tapped from the furnace. The working space was necessarily limited, and the disposal of slag and metal overflowing the ladle or lost because of breakouts presented a serious problem. The equipment, of course, was rather crude in the light of present-day development. Often no ladle stands were provided, the ladle being hung on the crane beneath the runner. When delayed taps occurred, the ladle was often held in position for many hours, thus tying up pit operations and causing delays to adjacent furnaces. Because of crowded conditions, slag thimbles were not used and a network of cast-steel triangles and old tapping bars, placed before the heat was tapped, was the means for removing slag from the hole. Furnaces of different capacities were used

Jan 1, 1935

William H. BLAUVELT, Anaconda, Mont.: Mr. Stetefeldt's comparison of the producer-plants at Aspen, Colorado, and Park City, Utah, is of special interest at this time, when the attention of all western metallurgists is so forcibly drawn to the necessity of reducing expenses and losses. The fact that wood was used at Park City before gas was introduced, for firing the Stetefeldt furnace and dryer, offered an excellent opportunity for showing the economies resulting from the adoption of gas in place of wood, as well as a comparison between the two gas-plants. Some time ago Mr. Stetefeldt contributed an article to one of the technical journals, in which the economy obtained by the substitution of gas for wood at this plant was shown quite in detail. I regret not being able to quote from his article at length, but, remember that the total saving effected would pay for the producer-plant in about one month. This is a striking instance of the advantages to be secured by the adoption of the best methods of using fuel in our metallurgical works. In comparing the figures from the Park City and Aspen plants, the difference of over 20 per cent. in the fuel used in the Stetefeldt furnaces, seems remarkable, even considering the larger amount of sulphur in the Aspen ore, and the greater rapidity with which it was roasted. It would be interesting to have Mr. Stetefeldt's, opinion as to the cause of so great a difference. The inferior economy of the revolving dryers at Park City might be overcome by lengthening them, or so arranging a second one above

Jan 1, 1894

By J. S. Pascover, S. V. Radcliffe

The structures and transformation temperatures of high-purity Fe-Cr alloys have been investigated as functions of composition (0 to 10 wt pct Cr) and rate of quenching from the high-temperature Y phase field (up to 40,000°C sec-1). The structures were chmacterized by transmission electron microscopy. The transformation temperatures for each alloy exhibited the progressive decrease to a constant value with increasing cooling rate which has been shown to be characteristic of several iron binary systems. The corresponding structures were found to become increasingly finer in scale with increasing cooling rate and solute content, but to remain essentially equiaxed in character. In all the materials except the high-purity iron and one of the alloys, an additional and lower transformation temperature than the constant value for the equiaxed structures was observed. The structures of specimens which transformed at these lower temperatures (only single thermal wrests were observed in any given run) were martensitic and consisted of arrays of fine ferrite laths which varied in size and morphology with changing solute content. The factors controlling the nature of these transformations are discussed. The composition dependence of the martensitic transformation temperature, ME, in Fe-Cr alloys together with those reported for other iron binary systems indicate that MB for pure iron is some 700°c, rather than the values of 550° and 760°C reported previously. This conclusion is further supported by the results of a compmison of the thermodynamics of mmtensite formation in several systems. ThE extensive investigations of the structures formed on athermal transformation in iron and its alloys have led to the characterization of several forms of martensitic or "military"1,2 transformations and, in addition, a "civilian7' transformation to ferrite or "equiaxed a"* which occurs athermally and at a very high rate.374

Jan 1, 1969

By F. C. Noyes

DAME Nature was in a generous mood when she distributed widely over the face of the globe numerous deposits of phosphate rock from which man can make phosphatic festiIizer to replace the phosphate re- moved from the soil by crops. The principal deposits are readily accessible to the world's greatest consuming areas and most of them are such that mining operations can be carried on at relatively low cost. The world's known reserves shown in Table 1 are sufficient to last well over 2000 gears at the present rate of consumption. Before giving a brief outline of the phosphate rock industry of foreign countries let us try to get a picture of the movement of phosphate rock throughout the world in 1938, the last full normal calendar year where it came from and where it was consumed. Table 2 shows the origin and finial destination of world shipments in 1938 by grand divisions. Table 3 (p. 499) shows shipment9 of phosphte rock to each country in Europe. Europe is seen to be by far the world's greatest market and the French North African mines the world's most important producers outside of the U. S. A.

Jan 1, 1944

By R. H. Edsal, G. Horvay

The transient one-dimensional heat-conduction equation is solved for two semi-infinite media, at different initial temperatures, brought into (poor) thermal contact. It is shown that the two interface temperatures gradually approach the well-known, instantaneously assumed, common interface temperature of the case of zero contact resistance. The present analysis, with slight modifications, may be used in fair approximation also for the class of problems involving a change of phase. One particular application of the boundary value problem solved in this paper concerns the determination of the temerature distribution in metal castings and molds.P This problem has been treated extensively by analytical methods (see e.g., the literature listed in Refs. 1 to 4) by electrical analogs (see e.g., Refs. 11 to 14) and also by experimental methods (see the literature listed in Refs. 4, 5), but prior to the work of Pellini and Ruddle the experimental results were rather unreliable. Immediate motivation for the work described in this paper was to better understand the results of Pellini,' which are typified by the curves of Fig. 1. Pellini cast 20-in. high, 7-in. sq steel ingots into cast-iron molds of various thicknesses. He measured the temperatures at mid-height, at a number of stations in the casting and the mold, and obtained the cooling curves shown in Fig. 1. The most conspicuous thing about Fig. 1 is the large temperature discontinuity at the interface between casting and mold, due presumably to the shrinking away of the casting from the wall and the attendant creation of an airgap, as the casting cools. Such a contact resistance slows down the anticipated freezing rate; an analytical prediction of this is of much interest in foundry practice. The determination of the effect of contact resistance in the presence of a change of phase will be dealt with, by an approximate method, in a separate paper.' In the present paper the much simpler problem is considered in which there is contact resistance but no change of phase. This problem frequently arises in the analysis of aircraft structures.+ It can initial temperature, and may be regarded as semi-infinite. We suppose the thermal properties in the two media to be time, temperature, and space independent; there are no sources or sinks within the media. In Fig. 2(a) we illustrate, schematically, the case of no contact resistance. The semi-infinite media "0" and "2:' initially at temperatures 8 (- m) and 8(+ -), respectively, are brought into contact at time t =0. A common interface temperature 8,i = is instantaneously established, and thereafter remains constant. Temperature curves are drawn for three instants of time. When there is contact resistance between the two media, the temperature equalization occurs as sketched in Fig. 2(b). Fig. 2(c) illustrates a temperature curve, using the dimension-less notation Barber-Weiner-Boley6 have stated the equations [23a, b] given below, which govern the heat transfer in the two media, and solved them for a rather complicated special case. In their example both media "O" and "2" are finite, are insulated at their far ends, and there is steady heat input into medium 2. In Eq. [27] we give the general solution of the most important special case, where the two media are semi-infinite and there are no sources or sinks. In this case the results may be stated in simple closed form. In Fig. 3, to be discussed in the next section, we illustrate the variation of the interface temperature when steel at 2760" is brought into contact with iron at 100". This example, if we disregard the effect of the heat of fusion, is comparable to Pellini's experimental results, Fig. 1. (Unfortunately, however, experimental determination of the interface temperatures was difficult to carry out, and hence Fig. 1 is not very accurate near the interface.) In Figs. 4 and 5 of the following section, we similarly compare Pellini's sandcasting tests with analytical results for the case where steel at 2760" is brought into contact with sand at 100". It will be pointed out that, insofar as the interface temperatures are concerned, heat of fusion has a minor effect, and so the present approximation, with small modifications, may be

Jan 1, 1961

By J. Paces, E. Miller, K. L. Komarek

The resistivity was determined as a function of temperature over the composition range from pure cadmium to 40 at. pct Cd. Melts with cadmium contents less than 85 at. pct had negative temperature coefficients of resistinity. On cooling below a transition temperature close to the liquidus temperature, the slope of the resistivity-temperature curve changed sharply. The activation energy calculated from the slope was 0.07 ev above the transition temperature and 0.14 ev below. The resistivity vs composition curve shows two maxima corresponding in composition approximately to CdSb and Cd3Sb2. THE relationship between the structure of a liquid and that of the crystal formed on solidification is at present not well-under stood. Various experimental determinations of the properties of liquids indicate that deviations from random atomic arrangements in liquids occur and that the properties of a solid and of its melt are closely related. Thermody-namic activities of liquids usually show negative deviations in systems where compound formation occurs in the solid,' and X-ray data indicate that close-packed solids and their melts frequently have nearly the same coordination number. Electrical resistivities and viscosities of liquids frequently exhibit maxima at compositions corresponding to compounds in the solid state. It should be of interest to study systems which have both stable and metastable compounds in the solid, and to determine if the short-range order in the liquid is affected by the existence of the metastable solid phase. The Cd-Sb system exhibits such a metastable phase. The phase diagram is shown in Fig. 1.3 The stable system has one intermetallic compound, CdSb, crystallizing in the orthorhombic crystal structure, with a melting point of 456°C. The metastable system also has one compound, Cd3Sb2, melting at 420°C and crystallizing in the monoclinic structure. Metastable alloys transform to the stable crystal structure in the temperature range from 250o to 350°C. Several distinct indications of very strong short-range order in the liquid phase have been reported in this system, with a close relation between the ordering in the liquid and the existence of both the stable and metastable solid phases. Scheil and Baach4 have observed distinctly different vapor pressures for liquid Cd-Sb alloys depending on whether the liquid solidified to the metastable- or stable-phase configuration. They observed an unusually sharp increase of the activity in a limited temperature interval immediately above the liquidus temperature of stable alloys, followed by a sudden decrease in slope to what they considered normal values. On cooling, the activity data reproduced the values in the normal range but then deviated from the values obtained on heating. They also observed that specimens of the stable phase upon melting and resolidifying always crystallized in the stable crystal structure as long as the melt was not heated to more than 485° to 525°C; otherwise solidification to the metastable phase occurred. However, in a later investigation, these results were not reproduced (13). The resistivity of liquid Cd-Sb alloys has been investigated by Matuyama 5, Oleari and Fioram, 8 and Belaschenko (141, but only above 500°C, the temperature region where Scheil and Baach observed no vapor-pressure anomalies. The data of Matuyama and of Oleari and Fiorani are reproduced in Fig. 5 and show a maximum in resistivity at 50 at. pct Cd. The data of Oleari and Fiorani, however, show the maximum as being rounded, and their values in general are slightly higher than those of Matuyama.

Jan 1, 1964

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949