Search Documents

By Edward Keller

In order to conduct intelligently the sampling of copper of various forms and grades, solid or in molten furnace-charges, a knowledge of this subject is essential. Yet figures and tests have been persistently withheld from publication, and the books at our command give us little or no information in this regard. This gap in our copper-literature has led to a series of experiments, the results of which are given below. Nearly all gold- and silver-bearing copper, destined for shipment, is cast into the form of bars or pigs. For the sampler, the question arises, Does copper, so cast, remain homogeneous ? If it does, sampling should present no difficulties; but, from experience, we know that this is not the case, and we are thus led to study the behavior of the precious metals arid impurities in copper when the latter changes from the molten to the solid state. For the purpose of the experiments here described, all available grades of copper were selected, and all of them mere subjected to the same conditions, an important requisite for proper comparison. The molten copper obtained directly from reverberatory- and blast-furnaces was cast in a cast-iron mould, the sides and bottom of which were 1 inch thick, and would, therefore, give the copper a fair length of time to chill. The inside dimensions of the mould, and, consequently, of the block of copper obtained, were: length, 10 inches; width, 9 inches; and depth, 5 inches. Fig. 1 illustrates the method employed to obtain samples from these blocks. A was cut away, and the face so produced BALTIMORE COPPER WORKS,

Jan 1, 1898

By Philip D. Wilson

OF all the metals in the war program the demand for and the production of magnesium have increased percentagewise the most. In the prewar year 1939 the production was 3350 tons. The war program, twice expanded, now provides for nearly one hundred times that amount annually. The goal announced by the War Production Board in February 1942 was 362,500 tons per year. Be- cause of the development during the year of satisfactory types of incendiary bombs other than magnesium this objective has been somewhat reduced but the capacity of the plants already built or under construction will be huge. The Aluminum and Magnesium Division of the W.P.B. has had the responsibility of planning and implementing this expansion and of providing fabricating facilities as well for this greatly increased tonnage of magnesium ingot.

Jan 1, 1943

By Frank Marotta, Louis B. Lesem, Frank Greytok, John J. McKetta

Although one of the primary variables in the calculation of the flowing bottom-hole pressure in gas wells from surface measurements is the temperature at any point and its distribution in the flow-string, only few experimental data are available in the literature and little attention has been given to analysis of the problem. Virtually all of the recently published methods of calculating flowing bottom-hole pressures depend on the assumption that either the temperature is constant at some average value or that the variation is linear with depth. The purposes of this work are to analyze the problem theoretically and to verify the analysis by comparison with experimental data so that practical problems in the analysis of the behavior of gas wells can be solved with greater accuracy, reliability, and ease. MATHEMATICAL OUTLINE OF PROBLEM Assuming that: 1. The mass velocity and chemical composition of the gas stream are constant and in normal gas well operations, the change in linear velocity in the entire flow-string is trivial, 2. The product of the density and heat capacity of the gas is constant, 3. No horizontal temperature gradient exists in the gas stream, 4. Net flow of heat by conduction within the formation and in the gas stream in the vertical direction is trivial in magnitude and can be neglected, 5. The regional vertical geothermal gradient is constant, and 6. The temperature of the gas entering the borehole is constant, and equal to that of the reservoir, a set of two simultaneous, linear partial differential equations with appropriate boundary conditions was derived to describe the temperature distribution in the gas stream and the surrounding formation. These equations were solved by operational techniques for the distribution of temperature in the gas stream. The resulting integrals were evaluated numerically on an IBM 604 at the Machine Accounting Div. of the Railroad Commission of Texas. DERIVATION OF FUNCTIONS FOR THE DISTRIBUTION OF TEMPERATURE The physical system is a circular hole of radius a in an infinite medium with thermal conductivity K, density p8, and heat capacity c,. Under shut-in conditions the well is in thermal equilibrium with the surroundings and the increment in temperature is given by - ?T3/L x. Gas of density pg and heat capacity c.. flows upwardly through this hole in the direction of increasing x with a linear velocity W. Writing a heat balance on an element of gas ?x in thickness, convective heat transfer + conductive heat transfer + energy required to lift a unit mass of fluid = change in energy content. pa2W po Co To - pa2Wpo Co To x+xx - 2apK?x ?T8/?r r=a - Wpa2 po?x/778 = CoPopa2?x?To/?t... Dividing by (copopa2?x) and taking the limit as ?x tends to zero, -W (?To/?x + 1/778Co) + 2 K/a Po Co ?T3/?r r=u = ?To/?t

Jan 1, 1958

By T. R. Braithwaite

The brief comments made in this chapter deal mainly with shaft sinking, but don't assume that freezing techniques apply only to shaft sinking. They can be used on tunnel work, on such things as liquid gas storage in sediment, and I think you will probably see other applications for it as we go along. The method was first developed in 1883 and was used to sink shallow shafts through water-bearing overburden in Germany and in England. One of the early shafts was in Germany and was sunk by freezing to 310-ft depth. The project required 17 months for drilling, roughly 5 1/2 months for freezing, and another 7 months for sinking, giving an average progress of 10 ½ fpm. Fortunately there have been numerous improvements and new developments in this technique through the years. With equipment and techniques available today, we can take a 20-ft-diam shaft down through 2000 ft of water-saturated overburden and the time schedule runs roughly 4 months for site preparation, freeze-hole drilling, installing the casings, and setting up the plant; 4 ½ months for freezing; and 6 months for excavating and installing permanent linings. This gives a progress rate of about 140 fpm, on average. I might qualify that a little in that the special linings that are required for some formations can affect the time. If it's straightforward sinking where one can use a heavy concrete lining, up to 630-640 fpm may be achieved in a shaft; but with special cast-iron tubbing or types like that, 5 fpd is pretty good progress, so the lining does affect the time. The freezing method is used mainly for sinking shafts through unstable water-bearing formations which cannot be grouted either effectively or economically and which are too deep to enclose in pile casing. Even with overburden, grouting methods available today can handle roughly 100 lb water pressure; in the range of, say, 100 to 150 ft from the surface, it's very often best to grout 40 or 50 ft. You normally drive a pile casing and go through it. Below that range, freezing is very often the economical

Jan 1, 1970

By AIME AIME

SOME 65 members of the Institute, including most of the Local Section delegates and several Directors and officers, were on hand for the Annual Business Meeting of the Institute held in the Engineering Societies Building on Monday, Feb. 21, at 4:30 p.m., immediately following the second session of the Local Section Delegates Conference. President Mathewson presided. The meeting was largely taken up with the presentation of committee re- ports, discussion of which was invited. F. E. Wormser presented the report of the Admissions Committee ; Philip Kraft, Papers and Publications Com-

Jan 1, 1944

By J. D. Bateman

At Giant Yellowknife, where high grade gold-bearing orebodies are highly irregular in shape, geology has been applied extensively to the mining of ore. The classical functions of the mine geologist in the fields of exploration and mine development have been extended to guide ore extraction, ensuring "clean" mining and effectively reducing waste dilution. THE property of Giant Yellowknife Gold M.ines Ltd. is situated west of Yellowknife Bay on the north shore of Great Slave Lake, a distance of 600 air miles north of Edmonton, Alberta. The Giant claims were staked in 1935, the company was formed in 1937, and the main orebody system was disclosed by diamond drilling in 1944 following a geological study of the property by A. S. Dadson,* Consulting Geologist for the company. Production began in 1948 at the rate of 200 tons per day and, during 1950, reached a daily rate of 425 tons. During the first 3 years of operation a total of 366,000 tons was milled with an average grade of 0.79 oz of gold per ton. Work is in progress with an expansion to 700 tons per day in view. A descriptive account of the geology and gold-bearing shear zone has appeared previously.* The rock formations in the vicinity of Yellowknife Bay have been subjected to protracted pre-Cambrian tectonic deformation culminating in a series of late faults having a cumulative horizontal displacement exceeding 11 miles. The Giant property is underlain by part of an Archean sequence, several miles thick, consisting of basic volcanic flows and minor intercalated tuffs. The volcanic succession forms the west limb of a major syncline, the flows facing east, but overturned on Giant property to dip west at 65" to 75". Orebodies are confined to shear zones up to 200 ft in width, which were formed along early thrust faults. The shear zones assume fold-like attitudes, the larger of which have an amplitude of several hundred feet. The rock formations beyond the limits of the zone of shearing do not reflect the simulated folds, the axes of which are within a few degrees of the strike of the flows. The schistosity and most of the planar elements in both the shear zones and the orebodies dip west • A. S. Dadson and J. D. Bateman: Structural Geology of Camdian Ore Deposits, Can. Inst. Min. Met. Jubilee Volume (1948), PP 273-283. at angles between 65" and 75", generally corresponding to the dip of the flows. The planar elements within the shear zone system thus dip more or less constantly west whether the shear zone is flat, vertical, or expressed as east or west dipping limbs. The shear zones reflect the deformation and alteration of the basic volcanic flows into chlorite schists which, in most places, have undergone metasomatic replacement to form chlorite-sericite-carbonate schists or sericite schists. The boundaries between the shear zones and country rock, although often gradational, usually can be defined within a few feet or even inches as they are expressed by the limits of metasomatic alteration. Orebodies may occupy a small or large proportion of the shear zone and, although they generally conform to the shape of the zone, their morphology is much more complex. Ore boundaries in some instances are sharp and can be delineated with a chalk line; but more generally, a large proportion of the ore boundaries is not visually obvious and can be determined only by the perception acquired by the geological mapping of ore or study of drill cores. Ore shoots in fold-like attitudes may transect the planar elements of the shear zone at any angle; yet the schistosity within the ore shoot may be coincident with that in the enclosing shear zone. Thus it is clear that problems may arise in the delineation of mining boundaries. Ore generally consists of 20 pct or more quartz with ferruginous carbonates in sericite schist deposited in two dominant stages. The earlier stage limits of quartz with carbonate, pyrite, and very fine-grained arsenopyrite in lenses and bands. The later stage consists of quartz-carbonate lodes, in

Jan 1, 1952

By Edwin A. Sperry

At the request of some of my engineering acquaintances, to whom the results became known, I submit the following description of the survey made by me for the underground tunnel-connection between the Riverside and Home coal-shafts, at Leavenworth, Kansas. The State law requires an escape-shaft; and as neither of the shafts had one, the two companies decided to make this connection in order to comply with the law and still escape the great expense of sinking

Jan 1, 1895

By R. E. Ogilvie, A. R. Kaufmann, S. H. Gelles

The solid-solubility limits of iron in beryllium were determined between 850o and 1200oC by analysis of differential type multiphase diffusion couples, using an X-ray absorption technique. The maximum value of the solubility limit was found to be 0.92 ± 0.02 at. pct (5.46 wt pet) at the eutectic temperature 1225°C. The solubilities of nickel and beryllium were determined between 900°and 1200°C by the same technique and the maximum solubility was found to be 4.93 + 0.01 at. pct (25.2 wt pet) at the eutectoid temperature, 1065°C. A previously unreported high-temperature phase which decomposes eutectoidally at 1065 °C was found to exist in the beryllium-nickel system at a composition of approximately 8 at. pct Ni (36 wt pet) by diffision-couple analysis. The presence of this phase was confirmed by thermal analysis and metallo-graphic analysis of the structure resulting from the eutectoid decomposition. G. V. Raynor1 has treated the solid solubilities of some of the elements in beryllium on the basis of the "Hume-Rothery" rules2 which have been modified to include ionic size and ionic distortion effects. It was predicted that the solubility of iron and nickel in beryllium should be slightly less than that of copper. The lowering of the solubility, according to Raynor, is due to a more unfavorable relative valency effect and an ionic size effect. Kaufmann and corzine3 have compiled data on the solubilities of elements in beryllium and have discussed them in the light of the Raynor paper. These authors feel that, because the elements having the greatest solubility in beryllium systematically fall in the Group VIII and IB Columns of the periodic table, the electronic structure greatly influences the maximum solid solubility of elements in beryllium. The solubility of iron in beryllium was determined by Teitel and cohen4 as part of the study of the beryllium-iron phase diagram. The determination was carried out by X-ray and thermal analysis and according to the phase diagram presented, the maximum solubility of iron in beryllium is 0.41 at. pct (2.5 wt pct) at 1225oC. However, it is estimated that the uncertainty in the position of the a-beryllium primary solid-solution boundary is about 0.5 at. pct (3wtpct). Losana and Goria3 in studying the beryllium-nickel phase diagram, determined the solid solubility of nickel in beryllium by thermal analysis. They found the maximum solubility to be between 1.65 and 2.65 at. pct (10 to 15 wt pct) at 1240°C. This value decreased rapidly with decreasing temperature. In determining approximate ranges of solubilities for different elements in beryllium, Kaufmann, et al,8 reported a value of between 1.3 and 1.7 at. pct (7.9 to 10.1 wt pct) for the solubility of nickel in beryllium. The value was obtained by metallographic examination of quenched alloys and lattice-parameter measurements. However, the authors also noted a single-phase structure for a 1.7 at. pct Ni alloy (10 wt pct) on cooling from the liquid. This would indicate a higher solubility range than was reported. ~isch,' in his X-ray studies of beryllium-copper, beryllium-nickel, and beryllium-iron intermetallic compounds, reports the disappearance of a second phase (Ni,Be2) in the beryllium primary solid solution at approximately 4 at. pct (20 wt pct). THEORY The analysis of concentration gradients in diffusion couples has proven to be a useful tool in determining phase equilibria.8-14 In this particular study the diffusion couples were chosen to straddle the expected composition range of the phase boundary, then heat treated at a given temperature and the concentration gradient evaluated. The composition of the phase boundary for a given temperature appears at a point of discontinuity of the composition gradient. Examples of typical phase diagrams and the concentration gradients which should be found in such systems are shown in Fig. 1. In the present work, gradients of the form of Fig. l(c) were obtained in diffusion couples made of pure beryllium and two-phase alloys of beryllium with either iron or nickel. The composition at the point where the gradient becomes discontinuous, Cs, corresponds to the solubility limit of either iron or nickel in beryllium. The analysis of the concentration gradients was carried out by an X-ra absorption method developed and applied by Ogilvie and later used by Moll13 and Hilliard.l4 It depends on the fact that the absorption of X-rays by matter is determined by the concentration and type of the various atomic species present. The relationship for the intensity, I, of a monochro-

Jan 1, 1960

By J. J. Egan, A. B. Kinzel

Much work has been done recently in an attempt to analyze the physicochemical mechanism involved in the production of steel by the open-hearth process. This has resulted in reducing the process to a series of interrelated phenomena obeying the usual laws of mass action and diffusion. Of these, the reaction of the iron oxide and carbon in the molten steel is of most interest from a technical point of view as it constitutes the main action in the usual steelmaking processes. A. L. Feild' has formulated a basic differential equation expressing the open-hearth reactions and Herty has done considerable experimental work on the determination of a number of constants involved in the basic open-hearth reaction. In considering the application of the law of mass action to the reaction FeO + C + CO + Fe, the iron will be taken as constant, as is the case in the open hearth and the carbon monoxide pressure will be assumed constant at one atmosphere. From this xy = m at equilibrium, where x is the percentage weight of carbon, y percentage weight of iron oxide and m the weight-concentration equilibrium constant. While it is customary for physical chemists to express equilibrium constants in terms of molar concentrations, the constant is here expressed as the product of the percentage-weight concentrations for ease of comparison with the constants quoted by Herty and by Beild, and for more ready applicability to the open-hearth reactions. Herty and his associates have attempted to calculate the value of this constant from data on open-hearth heats. So many variables affect these results that an adequate calculation presents very great difficulties. A value of 4 X lop2 was first arrived at, but this was later changed to 1.6 X 10-2. Feild, in order-to illustrate the operation of the differential equation of the open hearth, has assumed a value considerably lower than Herty's, namely, 1.0 X 10-2, the largest value consistent with certain theoretical

Jan 1, 1929

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By C. E. Sims

The carbon-oxygen reaction without doubt is the basic reaction in steelmaking. It is important on several counts: In the first place, carbon is the element that distinguishes steel from iron. It is the principal element controlling properties, and its control is of prime concern. Although the principal objective of the carbon-oxygen reaction is to oxidize excess carbon, the accompanying boil should not be underrated. The mechanical agitation, stirring, and mixing resulting from the boil are so useful in the distribution of heat and in promoting uniformity of composition in the bath that, were it not a natural accompaniment of the carbon-oxygen reaction, it is probable that something would have to be invented to replace it. The open-hearth operation, for example, with the bath heated from above by radiation, would be impracticable without the carbon boil. The electric-arc furnace is somewhat less dependent on it, but every melter knows how much easier it is to gain temperature with minimum damage to refractories during the boil than with a dead bath The motor action of the induced current of the induction furnace makes the carbon boil unnecessary but even there a severe oxidation has been found useful in giving greater freedom from porosity in certain steels. The quantitative aspects of the carbon-oxygen reaction have been given considerable attention by a large number of investigators, and the principles of physical chemistry have played an important part in these studies. Physical chemistry is the science of the mechanics and mathematics of chemical reactions. It is possible to study the mechanisms of reactions in a qualitative manner writhout reference to mathematics and thus obtain valuable concepts as to the manner in which the wheels go around. When it is desired to express quantitative relations in these reactions, however, resort to mathematics is not only convenient but necessary. Mathematics may also be regarded as the shorthand language of physical chemistry. A basic relation whose description requires numerous words may be expressed very simply by a mathematical formula or equation. A good example of this is the equilibrium constant for a chemical reaction. Expressed verbally, it is: When a chemical reaction has reached a condition of equilibrium, the Product of the concentration of the reacting substances on one side of the equation, divided by the product of the concentration of the reacting substances on the other side, gives a quotient that is a constant at constant temperature For the carbon-oxygen reaction C + O ^ CO this is expressed simply as % C X % O -%co where K (from the German Konstant) is the equilibrium constant for the reaction. Although mathematics is such a necessary and useful tool, it is also a potential pitfall. Mathematics in itself is an abstract science, which is not inhibited by consideration of mechanisms or materials.

Jan 1, 1948

By C. W. Binckley, F. R. Burgess, E. R. Haymaker

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By E. R. Haymaker, C. W. Binckley, F. R. Burgess

A method of establishing stabilized back-pressure curves for gas wells producing from formations of extremely low permeability is presented. Actual well performance under many different operating conditions is shown by the stabilized back-pressure curve. By use of the method. it is possible to conduct back-pressure tests with a critical-flow prover on wells that stabilize slowly, and save approximately 88% of the gas ordinarily vented to obtain satisfactory test data, with a great reduction in time required for testing. INTRODUCTION The reasons for establishing dependable back-pressure curves on gas wells have been pointed out by previous publications. The publication most referred to. of course, is the United States Bureau of Mines Monograph 7, titled "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices". The technique generally established therein has been accepted and used by many engineers; and, when proper tests are conducted, the results can be used for the analysis and solution of several practical problems concerning field operation and development. Even where formations of low specific permeability are encountered, the determination of a well's actual performance by the back-pressure test method permits the engineer to analyze many problems in individual well operation and also to predict necessary future field development. Such problems as the determination of the ability of a well to produce into a pipe line at a predetermined line pressure, the design of gas gathering systems and meter settings, and the determination of the time and the number of wells required to be drilled to meet future market obligations, can be solved, in part., by the use of a reliable back-~ressure curve. In addition, the computed well delivery rates determined by data from backpressure tests ordered by state regtilatory bodies, when compared with the true back-Pressure curve, permit the operator to ascertain whether such data represent unstable or relatively stabilized delivery rates for given pressure conditions of the well. The technique of back-pressure testing, as described in this report, was developed by Phillips Petroleum Company engineers from data obtained during a testing program that started in 1944 and has been continued to date. Three hundred and eleven back-pressure tests were conducted on 299 wells located in the southern part of the Hugoton Field. The gas-bearing zone is composed of several dolomitic formations of the Permian Age; the important ones are the Herington, Upper Krider, Lower Krider, and Winfield. The average bottom-hole temperature is approximately 91 °F.. and the initial wellhead shut-in pressures range from 400 to 440 psig. The spacing pattern is 640 acres per well with each well located near the center of the section. The range of back-pressure potentials on wells tested was from 500 to 23,000 Mcfd. All gas wells were acidized, and the quantity of acid used, expressed in 1574 hydrocloric acid, varied from 12,000 to 22,000 gallons per well. The quantity and concentration of each treatment depended on the stage, the formation being treated, and experience gained from previously completed wells. The gas in the Hugoton Feld is a "dry" gas. It has a gasoline content of approximately 0.25 gallons per thousand cubic feet, as determined by charcoal test, and its specific gravity averages about 0.71 as compared to air (air = 1.00 at 60°F.). Of the wells tested, 71 were completed with 7" casing, 3 with 9 5/8" casing, and 1 with 6%" casing set on top of the upper producing formation with the well bore through the gas bearing formations being open hole. Two hundred and twenty-four were completed with 5 1/2'' O.D. casing set through the gas bearing formations and perforated. For the purpose of establishing reliable back-pressure curves in the area, Phillips Petroleum Company personnel has computed data on the basis of 24-hour flows per point. Early in the program, many tests were actually permitted to flow 24 hours to obtain data for each plotting point, at great expense in man power and time. Presently, however, such tests have been replaced by tests of short duration flows which can be made to effect results that correspond to the tests obtained by flows of much longer duration. METHOD When a gas well producing from a reservoir of low permeability is opened for production through a constant size orifice, both the rate of flow and working pressure decline. first at a high rate and later at a lower rate until after several hours the decline becomes difficult to ascertain. In this paper the rae of flow and working pressure are considered to be stabilized when it becomes difficult to observe changes in working pressure during a period of three hours by the use of a deadweight pressure gage. Stalibization of pressure in the literal sense is never obtained in a producing gas well. In formations of low permeability. such as those in the Hugo-ton Field, most wellhead working pressures approach stabilization closely enough to be used satisfactorily in the determination of a back-Pressure potential curve after flow periods of 24 hours. We shall therefore describe the backpressure curve calculated from ohserved rates of flow and working pressure at the end of 24-hour flow periods.

Jan 1, 1949

By C. H. Frick

Before presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. Introduction The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accumulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3/16-in. round-hole screen and over a 3/32-in. or a 1/16-in. round-hole screen. Use of Smaller Sizes The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced—a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1949

By C. H. Frick

BEFORE presenting the main topic, as indicated by the title, this paper will give some of the high-spot history of the anthracite industry. INTRODUCTION The earliest recorded use of anthracite was in the year 1762, when a company of Connecticut pioneers discovered anthracite near the present city of Wilkes-Barre, Pennsylvania. In the early days of the industry, the coal was used only in large pieces, the smaller pieces being discarded to waste piles. As the output of the industry increased during the nineteenth century, uses were developed for somewhat smaller sizes down to and including pea coal. Early in the twentieth century, sizes smaller than pea, such as No. I and No. 2 buckwheat, were developed and used. Accu¬mulations of piles from current mining operations were still increasing; that is, the smaller sizes were still being discarded. It was not until after World War I that preparation of the so-called steam sizes began commercially. This was largely No. 3 buckwheat, which is screened through a 3f 6-in. round-hole screen and over a 332-in. or a M 6-in. round-hole screen. USE OF SMALLER SIZES The earliest recorded experience in burning the small sizes of anthracite for steam production, other than in a previous small experiment, was in the year 1913, when a size known as "boiler fuel" was introduced-a mixture of rice and barley (No. 2 and No. 3 buckwheat). At that time, there was still no method known for burning the still smaller sizes. TABLE I.-Screen Sizes Used for Small Sizes of Anthracite [ ] At the present time, various sizes down to and including No. 5 buckwheat are being prepared (Table I) from current mining and bank-reclaiming operations. The sizes of No. 4 and No. 5 buckwheat and smaller are generally being used for steam production in large boilers. The Pennsylvania Power and Light Co., following World War I, used 680,000 tons of anthracite per year, burned largely on stokers for production of steam, whereas for the year 1943 it used 1,940,000 tons of stoker sizes and 400,000 tons of smaller sizes for grinding and burning in pulverized form. This company has taken a very large part in the research and development of ways and means of burning these smaller sizes of anthracite, including the grinding of the very small sizes. This paper is particularly concerned with the latter feature.

Jan 1, 1946

By Wallace Ralston

DuRing the year of 1937, the East Texas district produced 211,194,467 hbl. of oil and marketed more than 22,329 million cu. ft. of gas; 3377 oil and gas wells were completed. During this same period 106 exploratory wells were drilled, discovering three new oil fields and one gas-distillate field. Fields East Texas Field.—The East Texas field again led the district as to production and number of wells completed. During the year, 2420 oil wells were completed, making a total of 24,382 producing wells, which produced 171,336,854 bbl. of oil, for a total of 1,156,352,834 bbl. since the beginning. During the year the average bottom-hole pressure dropped 49 lb., making the average bottom-hole pressure 1119 lb. Approximately 3500 wells are making salt water, 20 per cent of them making over 80 per cent of the water. During the month of December, the daily average production of salt water was 119,000 barrels. Talco Field, Titus and Franklin Counties.—The Talco field produced 9,780,948 bbl. of oil during the year, from 637 wells. During the year 472 wells were completed. All of the wells are pumping and 241 are making salt water. This field has followed a normal development and did not exceed the estimated number of acres reported last year. Rodessa Field, Cuss and Marion Counties.—The Rodessa field was extended about 13 miles southwest into Marion County, which added approximately 4000 acres to the field. During the year 260 wells were completed, making a total of 416 producing wells, which produced 12,646,-970 bbl. of oil. The author was unable to obtain figures for the amount of gas produced. The field has two gasoline plants, which had a daily average of 16,558,000 cu. ft. of gas during December, averaging 0.83 gal. per M cu. ft. As of Jan. 1, 31 wells were making salt water. The bottom-hole pressure varies greatly, depending upon the pay from which the well is producing. The average bottom-hole pressure from the Young

Jan 1, 1938

By F. N. Rhines, A. S. Nemy

The mode of high-temperature tertiary creep of 523-0 aluminum alloy was found to be strongly stress dependent. The occurrence of necking and/or fissures during tertiary creep exhibited a sequence with varying stress, wherein fissures with no necking occur at a minimum stress and necking with no fissures occur at a maximum stress. At an intermediate stress, tertiary creep begins without necking but with fissures in a region just beneath the external surface, followed by necking and the development of fissures along the axis of the specimen. The results are interpreted in terms of grain boundary gliding and the hydrostatic stresses produced by restraints to grain boundary gliding. THERE appear to be two possible reasons for the existence of a period of accelerating elongation prior to rupture during high-temperature creep in metals; namely, 1) a change in the structure of the metal itself, leading to a change in its response to loading, and 2) a reduction in the cross section of the metal resulting in a higher unit loading. Howe,' by annealing and retesting broken low-temperature creep specimens, found that irreparable damage is done once a metal is subjected to creep. Andrade2 first pointed out the association between the reduction in cross section and the increase in creep rate. The present research was designed to investigate both of these factors by retesting specimens machined from material which had been subjected to high-temperature creep testing short of rupture. EXPERIMENTAL METHOD An aluminum alloy, 52s-0, was selected for these studies because it is constitutionally simple, is strong enough to be relatively insensitive to mechanical damage during machining,3 and undergoes accelerating creep in a convenient temperature range. This alloy is hardened by 2.6 wt pct Mg in solid solution and is not subject to overaging effects; it has a very small quantity of an insoluble impurity phase, Mg2Si, finely dispersed throughout its micro-structure. Creep specimens, similar in design to ASTM 0.252-in. tensile specimens, were machined from 3/4-in. round stock and the surfaces were electro-polished. A 24-hr anneal at 500°C was then applied to stabilize the grain size to an average diameier of 0.27 mm. Subsequent heating for as long as 700 hr at the intended test temperatures produced no change in the tensile properties, indicating a well-stabilized state of the material. Corresponding to each of the typical testing conditions listed in Table I, one creep specimen was tested to destruction and this test was employed as a guide in the selection of times for subsequent tests. Duplicate creep tests were then run to various points along the creep curve to produce specimens which were used to determine changes in mechanical properties and microstructures. The latter were examined at the midsections of the specimens. Other specimens were tested to various stages of tertiary creep, after which they were remachined to new cylindrical test specimens, electropolished and re-tested in creep. RESULTS The major findings of this investigation may be illustrated by a comparison of the results of three sets of creep tests. These were run at 400°C at three stress levels, namely 750, 1000, and 1500 psi. In presenting these results in Figs. 1, 5, and 8, the creep curves are given in pairs: That curve of each pair which is drawn through filled circles corresponds to the initial test, and the curve drawn through open circles (and designated by - R) represents the result of retesting the same specimen after machining to a new cylindrical surface. The load was readjusted to the original unit stress at the beginning of each retest.

Jan 1, 1960

IN GATHERING material for this chapter on Yerington and the one to follow on Silver Bell, the A.S.& R. project near Tucson, Arizona, I was fascinated at the way the two stories paralleled each other. For example, here are a few instances: (1) The first copper mining in the Yerington district of Nevada was in the late 1860's; the first in the Silver Bell area in 1873. (2) Each district was served by a branch railroad about 25 miles long from a main line of the Southern Pacific (by quizzical coincidence); and, in each instance, the railroad was later abandoned and torn up. (3) Each district had a sizable blast-furnace smelter ten or fifteen miles from the principal mines, and in each instance the smelter was later dismantled for junk. (4) Up to 1954, the Yerington district was credited with a production of 100,000,000 lb of copper; the Silver Bell district with 80,000,000 lb. (5) In each district the entire production had come from deposits other than the low-grade ore bodies now being exploited. (6) In each instance, existence of the low-grade deposits of the Porphyry type was recognized in the period circa1910-1914 and a substantial amount of exploratory drilling had been done, on one deposit at Yerington and on two at Silver Bell. (7) In each instance, the properties containing the Porphyry ore were acquired by a strong company (Anaconda Copper Mining Company at Yerington and American Smelt-

Jan 1, 1957

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By R. G. Knickerbocker

A STURDY and consistent expansion of the metal industry occurred in 1947 exemplified by an increase of approximately 30 per cent in steel consumption over 1946. For this major reason, ferroalloy metals have seen their most useful and important peace-time year. The current domestic rate of consumption of high-grade ferroalloy ores, together with added consumption of new foreign producers as well as for eign nationals' restrictions on high-grade exports, makes very evident the increasing difficulties of obtaining sufficient high-grade ores. This accentuates the need for new and less expensive methods of production of ferro-alloy metals of higher purity from lower-grade domestic resources. As an important factor in preparedness, procurement of these high-grade, -critical ferroalloy minerals and metals for our nation's stock piles is a most important task. Also, this stock-piling can be the means of supplying incentive for the industrial development of the new metallurgical processes and plants necessary for the recovery of ferroalloy metals from our domestic low-grade deposits.

Jan 1, 1948