Search Documents

By Walter Harvey Weed

Introductory.............449 Summary oF Types............452 I. The Virgilina Type...........452 The Virgilina mines...........452 Location.............452 History.............453 The rocks of the district..........453 The veins.............454 Notes on the mines.... 458 The Holloway. 458; Yancey and Durgy. 465 ; Copper World. 467 ; Frazier. 467 ; Thomas. 467 ; Anaconda. 468; Blue Wing. 468; High Hill. 472; Dorothy.......474 II. The Gold Hill Type...........474 The Gold Hill mine...........475 Location.............475 History............• 475 Surface improvements.......... 476 The rocks............478 Vein.phenomena...........478 Character of the ore..........481 Origin of the ore...........481 Notes on the mine.workings.........482 Other occurrences of ore-deposits of the Gold Hill type.. .. 483 III. The Ducktown Type..........484 The Ducktown mines...........485 Other examples of the Ducktown type....... 494 Alabama mines...........494 North Carolina examples : Ore Knob.......496 Virginia examples..........497 IV. The Catoctin Type.. ......... 498 General characteristics,......... 498 The Linden district...........499 General distribution of the Catoctin type.......503 Introductory. In the early history of this country the existence of copper in the Appalachian region was well known. but no mining mas attempted until the discovery of the Ducktown deposits in

Jan 1, 1901

By R. J. Wysor

MORE than two years ago, in making efficiency tests on our hot-blast stoves, I was surprised to discover a marked difference in temperature as indicated by a pyrometer inserted near a stove on blast, and the regular recording instrument situated near the bustle pipe. A special hole was then provided at the junction of the hot-blast main and the bustle pipe, and portable pyrometers with bare fire ends were used, both at this point and in the stove necks. I had occasion to make a number of such tests on various stoves on the same furnace, the difference in temperature as shown by the two pyrometers varying chiefly with the temperature of the blast, and the distance of the stove from the furnace. However, this difference was always great, often averaging above 100° F., for the entire period of a stove on blast. Later, experiments were made with similar results on another group of stoves. The pyrometers used were properly standardized and checked against each other before and after each test. However, there was still a slight doubt as to the accuracy of the results obtained, as subsequently explained. But I have obtained corroboration of the magnitude of heat losses from blast-furnace hot-blast mains from two independent sources. I have learned from H. A. Brassert, Superintendent of Blast Furnaces, South Works, Illinois Steel Co., that he has recently clone some experimental work similar to my own, and found temperature drops of the same order of magnitude. Also, C. R.. Lyle, of the Armstrong Cork Co., has made some interesting theoretical calculations, based oil the thermal conductivity of fire brick, for the particular conditions of several of our tests; and his theoretical interpolations, all facts being considered, check our actual observations fairly well. I understand that Mr. Lyle expects to publish the results of his investigations.

Jan 10, 1915

By N. A. Parlee, A. E. Lord

Measurements of the solubility of lead in liquid iron were made at 1550°, 1600°, 1650°, and 1700°C using two different methods, i.e., 1) liquid iron-liquid lead equilibration and 2) liquid iron-lead vapor equilibration. LEAD was long considered insoluble in liquid iron1. Today steels containing 0.15 to 0.35 pct Pb are used. One laboratory has found a solubility of about 0.5 pet in the 1600°C range. Recently Miller and Elliott2 gave 0.60 pct as the result of one determillation at 1540°C. Because these findings resulted from the

Jan 1, 1961

By Thomas M. Drown

IN a communication to this Institute at the Baltimore meeting, February, 1879,* on the "Determination of Silicon in Pig Iron and Steel," the method recommended was the treatment of the metal with nitric acid until action had ceased, and then evaporating with sulphuric acid until the nitric acid was nearly or quite driven off After filtration of the siliceous and carbonaceous residue, and washing with hot water and hydrochloric acid, a silica was obtained, on ignition, which was quite pure. Since this paper was read before the Institute, we have had large experience with the method, and * Transactions, vol. vii, p. 346.

Jan 1, 1880

By D. B. McDyre

THE object of this study was to compare variations in slag volumes with tap changes while maintaining all other factors constant. This meant: 1. Same type of heat (Spec. SAE 1030). 2. Same charging material (3500 lb foundry, 4000 lb bought scrap). 3. Same amount of sand by weight to fix slag line. 4. Same method of melting with the exception of tap changes. 5. Same method of weighing slag after each test. The equipment of the Dodge Steel Co. consists of a 132-ton Heroult furnace lined with silica brick, using three 8-in. electrodes and a 2000-kva transformer, with four tap changes. In the melting practice we use a Fischer Carbanalyzer and a Herty viscosimeter and try to standardize all heats by making necessary carbon and slag adjustment before boil to keep all heats as uniform as possible.

Jan 1, 1947

By Alex G. McKenna, Thomas M. Drown

The unsatisfactory character of most, if not all, of the processes for the direct determination of alumina in the presence of iron and phosphoric acid, and the sharpness with which both the iron and phosphoric acid can be determined, have led chemists to rely mainly

Jan 1, 1892

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By F. F. Schmidt, H. R. Ogden, E. S. Bartlett

ThE solubility of carbon in tantalum has been reported to be very low at temperatures below 1500 C,1'2 increasing to at least 0.02 wt pctl at the eutectic temperature of 2800°C. The solubility limits at low temperatures were based on metallo-

Jan 1, 1963

By Charles A. Schaeffer

IN the early part of last year I received a small amount of powdered mineral from Williamson County, Texas, to be examined for silver. The specimen proved to be limestone, slightly colored

Jan 1, 1883

By John W. Rushton

This month's article concludes the series with maintenance design considerations in secondary crushing, grinding, and flotation circuits.

Jan 4, 1978

By Peter F. Weiss

INTRODUCTION Austro-American Magnesite Co. of Radenthein, Carinthia, Austria, is a wholly owned subsidiary of General Refractories Company, Bala Cynwyd, USA, and has been incorporated since 1908. The raw material basis is the magnesite mine on Millstatt Alp, located in the mountains near Radenthein at an altitude of 1500 m above sea level. The mined crude magnesite is crushed in a surface crushing plant to minus 35 mm and consequently hauled to the processing plant in the valley by means of a cable conveyor of 7.5 km length. The annual production of 350,000 mt is accomplished with 20 supervisors and 122 workers (of those 60 are in the mine). The labor requirement for block caving is 0.2 man hr/mt, corresponding to an output of 40 mt/man/ shift. GEOLOGY The rock in this area mainly consists of crystalline type schist. There are mostly coarse crystalline garnet mica schists with varying mineral concentrations, and to a lesser degree, some deposits of amphibolite and marble. This petrographically rather homogeneous rock is divided into numerous different tectonic units (covers and scales). The magnesite deposit itself is a foreign body that also has been tectonically inserted. The ore body has a length of 600 m, is 450 m deep, and has a thickness of 60 m on average, varying substantially however, The contact with the accessory rock is very precise. The deposit 1 = ore body, 2 = previous open pit, 3 = caved in area, 4 = block under excavation, 5 = land slide consists of coarse crystalline magnesite in excess of 90 per cent. The few impurities consist of dolomite and talc. The lower part of the deposit is inclined parallel with the schists at approx. 40 degrees. In profile it can be seen, however, that the upper part of the deposit has been tilted over. This is a result of a post-glacial land slide reaching from the bottom of the valley at 1400 m above sea level to the peak of the mountain at 2100 m above sea level. Due to this land slide, with horizontal movements of up to 100 meters, as well as older tectonic events, the rock was crushed to a vast extent. Through mining, the land slide was reactivated; about 40 million cubic meters of rock slowly flow downhill almost like a plasticized mass. Near the surface, the rock is completely crushed and resembles a glacier rupture zone. This renders the originally impermeable rock completely water permeable so that practically all of the annual quantity of 1000 to 1100 mm of precipitation permeates the rock and flows down into the mine. The carbonate rock turns into the preferred aquifer. From 1700 to 2600 cubic meters of water have to be pumped from the mine daily. On one hand, additional problems are caused by the water in the mine, on the other hand we have learned to make use of the down- hill pressure forces to improve the crushing process during block caving. The boundary of the downhill shearing zone moves downward as mining goes deeper.

Jan 1, 1981

By Ionel I. Gardescu

In connection with some of the experiments carried out by the writer on the behavior of gas and oil in a sand reservoir,' an interesting phenomenon was observed which may throw some new light on the problem of recovery of oil from a natural reservoir. The experiments are intended to show the effect of the surface area of the occluded gas masses, originally present in a reservoir, on the further evolution of gas from the oil and its consequent effect upon the rate of production of oil. The apparatus used in the experimental work is shown in Fig. 1. It consists primarily of a sand reservoir R and a displacement chamber D, which is used to induce small variations in volume. The reservoir and displacement chamber form a unit, and a lowering of the plunger D is equivalent to increasing the volume occupied by the oil and gas in the reservoir. The reservoir was first filled with dead oil and maintained under pressure until it was ascertained that most of the free gas had gone into solution. The volume of free gas present in the reservoir was computed from the coefficient of compressibility of the fluids by means of the displacement chamber D, reading to 0.005 c.c. and a special gage J reading to 0.02 lb. per sq. in. The oil was saturated with gas under pressure in reservoir S by circulating the oil for a long period of time through the gear pump B. Subsequently, the saturated oil was circulated through the sand reservoir following the circuit S6, B, S6, R4, the sand reservoir R, R1, R², F4, F1, back to reservoir S. In the following experiments the sand reservoir R was filled with gas-saturated oil at a pressure of 415Ib. per sq. in. with no free gas present. This was ascertained by closing off all the outlet valves and determining the coefficient of compressibility of the system by means of the displacement chamber D. Much difficulty was encountered in eliminating all of the free gas masses from the oil reservoir. The dead oil originally present in the

Jan 1, 1932

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

By F. R. Zacher

Unmined blocks in the Sewickley seam, surrounded by worked out areas, have been found to transmit overburden oads through the interval strata to the Pittsburgh seam workings 90 ft below. Operating experiences under these conditions are described in this paper. IT has always been understood, in northern West Virginia where both the Pittsburgh and Sewickley seams are mined, that pillaring or splitting in the lower Pittsburgh seam could break the interval strata and make mining in the overlying Sewickley difficult or impossible. In some instances, however, mining methods practiced in the overlying Sewickley have reversed the problem, resulting in a shifting of the intermediate layer and destroying valuable acreages of the Pittsburgh seam below. The Pittsburgh seam in this area is, on the average, 102 in. thick. About 18 in. of low-quality head coal are left for roof protection as it is mined. Immediately over the coal are two draw slates, two rider seams, and a good hard black shale, locally called black rock, which serves as a permanent roof where draw slates and riders are taken down on certain main haulroads. In most areas mined in this seam in the past the bottom has been satisfactory but soft. However, in areas now being mined by the Christopher Coal Co. in Monongalia County the bottom is very hard and unyielding. The Sewickley seam, lying 85 ft above the Pittsburgh, will average nearly 70 in. in thickness and is overlain by massive shales and sandstones. Much of the seam is mined only down to the "sheep skin," a hard band about 4 in. above the bottom, which is composed of relatively hard shale. Fig. 1 shows a typical cross-section through the Pittsburgh and Sewickley seams in the area being discussed. The thin Redstone seam is not deep-mined but is stripped in some locations where it outcrops. Most of the Sewickley seam in the Morgantown areas has been mined out from 10 to 30 years. There are at present only two large mines and five or six others of small production operating in that seam. Mining systems in the past were generally of the room and pillar type with some full pillar extraction. This seam in the Scott's Run area was operated by as many as thirty or forty different companies at one time, during an era beset with strikes, market failures, and depressions. Most of the barrier pillars along the many main haulroads were abandoned, and blocks of Sewickley coal that would be fully recovered with today's machinery were left unmined when conditions became anything less than favorable. Consequently the mined-out Sewickley is spotted throughout with solid blocks varying in size from 100x100 ft to 200x400 ft and larger. It is these unmined Sewickley blocks surrounded by worked-out portions that have caused transmissions of roof stresses to underlying Pittsburgh mining areas, see Fig. 2, resulting in untold difficulty. As the Christopher Coal Co. operates both the Pittsburgh and Sewickley seams, accurate maps of workings in both seams are readily available and are regularly consulted. The first Pittsburgh squeeze attributed to overlying Sewickley blocks occurred in the Arkwright mine, where a shuttle car crew was developing a section consisting of seven panel headings. These entries were being driven in solid coal 3400 ft from the nearest worked-out Pittsburgh area. As mining advanced it was noticed that certain ribs began to slough and certain areas to show signs

Jan 1, 1953

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ANDERSON, AMIL A., Co. A, 309th Regiment Engineers, 84th Div., American E. F., Care Postmaster, New York. ARMSTRONG, HAROLD K., Pilot, Naval Aviation, U. S. Naval Air Station, Miami, Fla. BASSETT, ARTHUR F., Co. 6, -E. 0. T. S., Camp Humphreys, Va. BEDDALL, THOMAS H., Adjutant, 1st Battalion, 1st Gas Regiment, American E. F. BERNARD, CLINTON P., Candidate, 12th Observation Battery, F. A. C. 0. T. S., Camp Taylor, Ky. BROOKE, LIONEL, 50th Co., 13th Battalion, 5th Replacement Engineers, Camp Gordon, Ga. BROWNING, EDWARD, Corp., 1st Regiment Engineers, Co. D, American E. F. BUGBEE, EDWARD E., S. A. T. C. Headquarters, Raleigh N. C. BUTTERFIELD, G. BRUCE, CO. C, 605th Engineers, American E. F. CADOT, J. J., 1st Lieut., U. S. Air Service, American E. F., Care Post- master, New York. CARLOCK, J. B., Major, 2d Battalion, 1st Gas Regiment, American E. F., France.

Jan 12, 1918

By W. J. Parton

The efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/32 by 1/32 in.) and No. 5 Buckwheat (1/32 in. by 0), pre-sent a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than 3/32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes. The object of this paper is to de- scribe a stationary screen device from which the underflow is restricted by orifices, called a launder screen, along with operating results of several applications of this screen; a settling tank in which two classified products are produced by the installation of a cylindrical partition of smaller diameter than the original tank, one product being recovered from the small tank created by the partition and one product from the space between the inner and outer tank walls; a small pocket classifier or hydraulic trap for use in removing high ash particles from a sludge flow; the classification or segregation of sludge solids occurring in a 16 in. diam pipe flow by analysis of samples procured at different zones; and the operating results of a Fahrenwald sizer, as well as the performance of the concentrating tables handling the classified products. These simple devices were employed at the collieries of the Lehigh Navigation Coal Company Incorporated, Lansford. Pa., in order to improve preparation results on the fine sizes of anthracite. Launder Screens The launder screen is a screening and dewatering device which probably could be used advantageously in the flow diagram of many fine coal plants. Fig 1 shows that it consists of a stationary screen constructed by placing 6 in. high partitions every 6 in. along a launder. Holes are then drilled on 6-in. centers across the bottom of the launder to receive pipe bushings of the desired diameter. The screen cloth is tacked on top of the partitions. When water and solids are fed to the screen, only a small portion of the total water is removed through the orifices in each compartment so that the water in the feed is distributed evenly over the whole length of the screen. The screening action which results is very efficient because the solids are kept in a fluid condition for the full length of the screen. Blinding of the screen can be minimized by the use of screen cloth

Jan 1, 1950

By Samuel G. Vera

INTRODUCTION The Climax Mine is a property of Climax Molybdenum Company, a division of AMAX Inc. Climax is located in the central part of the Colorado Mineral Belt on the west slope of the Tenmile Range, Lake County, Colorado at 3,425' m. above sea level. Climax Mine, the largest single producer of molybdenum in the free world, has been a cornerstone of mining in the State of Colorado for many years. Before molybdenum was known, the early hunters of gold and silver laid their hands on the outcrops of the Climax deposit and left it as low quality lead or graphite without much value. Today, 44,000 TPD of ore is extracted from the heart of Bartlett Mountain. The molybdenum, separated from the ore, is vital for mankind, being used for everything from fertilizer to fine components of aerospace ships, because of its valuable physical and chemical properties. The operations at Climax have never remained static. Constant demand for the "gray gold", and technological advancements, have converted Climax into an "open book of technology", where learning the still-hidden secrets of mining is a continuing process. (All figures related to tons are metric tons) BRIEF HISTORY The mine produced its first molybdenum ore in 1918. It was shut down in 1919, resumed production in 1924, and has been in continuous production since that time. During World War 11, a peak of 20,000 tons per day was reached, then tonnage dropped from 1945 to 1950. Since 1951, production has been in- creasing, reaching a peak of 46,000 tons per day during the month of June, 1980. Early mining used shrinkage stoping. Block caving using the grizzly system was introduced in the early 1930's. Caving methods were improved through empirical studies of rock behavior and by trial and error, evolving a very efficient mining method by the late 1940's. This form of continuous retreat panel caving, with small modifications, is still used today, and has made the Climax Mine one of the biggest underground mines in the world. The Climax Mine, synonymous with molybdenum, was essentially an underground mine until 1973 when the open pit was introduced. Since then, both mining methods have operated successfully. Current production is 60% from underground, and the remaining from the open pit. Climax has been in continuous operation for 56 years, and as of December 31, 1980, more than 386 million tons of ore have been mined. The orebody is not fully defined, and at the present mining rate, the known life span of the mine will be to the year 2020. GEOLOGY The Climax deposit is a large low-grade porphyry molybdenum deposit somewhat similar to porphyry copper deposits, with a well- mineralized quartz molybdenum stock work sys- tem. It lies within the pre-Cambrian granites and schists and the Tertiary Climax porphyry. The age of mineralization is thought to be mid-Tertiary and is characterized by fracture filling and replacement through silicification. The main economic mineral is molybdenum, with pyrite, cassiterite and wolframite as by-products. Fluorite and topaz also occur, but are not recovered at this

Jan 1, 1981

By E. B. Olds, B. P. Burt

The mines of the Consolidated Gopper-mines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 11/2 miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1949

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By Frederick Laist

THE ore from the Butte mines of the Anaconda company is quite siliceous; that is, it contains considerably less iron than is needed for the fluxing of the silica. The direct smelting of this ore, therefore, requires the addition of considerable fluxing material. The only flux available in sufficient quantity at Anaconda is limestone containing no metallic minerals. This necessarily makes the direct smelting of the ore so expensive that it is more profitable to subject the ore to a preliminary treatment by concentration. However, as the losses in the concentrator were very high, compared with the losses in the blast furnaces, it was found, by calculation, more profitable to send ores containing more than a given percentage of copper to the blast furnaces, in spite of the higher costs of treatment. The dividing point was dependent on various factors, the chief of which was the prevailing market price of -copper. It was customary, therefore, to segregate the ore as mined into two classes. Ore in the first class generally contained 5 per cent. or over of copper;: this was sent directly to the blast-furnace department. Second-class ore contained less than 5 per cent. of copper, and averaged around 3 per cent.; it went to the concentrating department. With the introduction of the flotation process, it was found possible to maintain an average recovery, as concentrates, of 96 per cent. At the same time, the cost of reverberatory smelting was very materially decreased by the use of pulverized coal. These two changes in practice made the blast furnaces unable to compete with the reverberatory furnaces on a cost basis. The distinction between first-.and second-class ore was therefore abandoned, and the ore was treated by concentration. Obviously, on ores as high in iron as the Butte ores, the concentrator, produces a product that is self-fluxing; in fact, it is possible to produce a

Jan 1, 1920