Search Documents

The separate outputs of Burma and India in 1937 were 274,664,365 gal. valued at £4,474,147 and 75,657,857 gal. valued at £1,030,591, respectively. The corresponding figures for the year 1938 were 263,823,-265 gal. valued at £3,766,810 and 87,082,371 gal. valued at £1,234,563, respectively, which is a slight increase in total quantities but a fall in value for the combined outputs of Burma and India. The appreciable increase from India in 1938 is due to an increase of over 11 million gallons from Attock and a little from Digboi, while the decrease from Burma is due to a fall of nearly 9 million gallons from Yenangyaung, over 3 million gallons from Yenangyat (and Lanywa) and half a million gallons from Minbu (Table 1). The 'amount' of gasoline produced from natural gas during the year 1938 was 10,587,291 gal. in Burma and 496,163 gal. in the Punjab.

Jan 1, 1940

Jan 1, 1933

By AIME AIME

T HE Institute of Metals Division and the Iron and Steel Division will meet jointly at the Stevens Hotel, Chicago, during the week of the American Metals Congress, Sept. 22-26. The Iron and Steel Di- vision of the American Society of Mechanical Engineers, the American Society for Steel Treating and the American Welding Society meet at the same time. but the sessions have been arranged to conflict as little as possible. A rich program of papers and plant visits has been arranged for the members and guests of the two Institute Divisions. The annual dinner and a pro- gram of entertainment are being arranged by the Woman's Auxiliary of the Chicago Section. Members are urged to register immediately up011 arrival and to make dinner and plant visit reservations at the same time.

Jan 1, 1930

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a' phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a' phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.' Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a', with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a' phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a'. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By Walter Miller

With returning prosperous conditions in all industries, oil-refinery engineering has found opportunity for the more extensive application of improvements developed during the several years of depression. The year has brought out little of an entirely new nature, but much in wider application of previous worth-while developments. The greatest volume of work done has been in modernizing the distillation and cracking units of existing refineries, particularly by substitution of combination skimming and cracking units for older equipment, and the installation of cracking plants in smaller refineries where formerly only skimming was practiced. A number of entirely new refineries were installed during the year, two of the most important being the 20,000-bbl. refinery by the Atlantic Refining Co., at Atreco, Tex., and a 12,000-bbl. plant by the Wilshire Oil Co., at Norwalk, Calif., these two embodying some of the latest developments in cracking and treating. Total refining capacity for the United States is now reported as being something over 4,000,000 bbl. per day, but a movement is on foot looking to a complete revision of these figures, as experience has indicated not only some overstatement of capacity of equipment but that considerable equipment is included which because of obsolescence and location will probably never be run again. The 3,000,000-bbl. figure which the industry reached during the year's high consuming period required the operation of probably 95 per cent of the country's efficiently usable capacity. Cracking and Polymerization There were no new outstanding developments in the cracking field, progress being made largely in the further refinement of known principles. Improvements in furnace design and operation have been largely in permitting closer control of the heating curve through the cracking-tube system, assisting in more uniform yield and in the lessening of coke deposition, and permitting longer trouble-free operating time as well as reduction in furnace-maintenance cost. Actual operating polymerization capacity has been increased little during the year, but a number of projects have been started, some nearing completion, the production from which will be available during 1937.

Jan 1, 1937

By Verne E. Hooker, Robert M. Becker

The evaluation of in-situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is aniso tropic. A plane elasticity solution fora circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated. The determination of in-situ rock stresses from boreholc deformation measurements has gained widespread acceptance. Hastl measured the change in diameter of a borehole that was stress-relieved by drilling a larger concentric core; this overcoring method has produced a major portion of the field data for recent stress evaluations in rock. These evaluations are based on the elastic properties of the rock, which are conveniently determined by testing the overcore.6-8 The stress evaluation and the overcore testing procedures generally assume isotropic relations whereas rock is anisotropic in varying degrees. Recently, an anisotropic plane stress solution was adapted for evaluation of in-situ stress9 and a related plane strain solution was developed for the testing of stress-relief core. 10 The present paper unifies the stress evaluation and overcore testing procedures for a general class of anisotropic rock. Equations are presented for calculating the state of stress in a plane normal to the borehole, and a consistent thick-wall cylinder solution is given for determining the necessary elastic properties. In addition, a complete example of stress evaluation from laboratory and field data is presented, and the order of error in computing the state of stress from isotropic relations is illustrated. Several limitations of the results should be emphasized. All results assume small linearly elastic deformations of a homogeneous medium. Rock characterized by orthotropic, transversely isotropic, and isotropic elasticity is considered; however, the anisotropic results assume a special relation among certain elastic constants in addition to geometric orientation with respect to a plane of elastic symmetry. For some stress determinations in rock, these may be severe limitations. On the other hand, the anisotropic evaluation procedure involves little additional effort and is much more flexible than the corresponding isotropic evaluation procedure. The collection of field data is identical. The laboratory determination of elastic parameters is no more difficult and time-consuming for the anisotropic than for the isotropic model. Only the calculations require some additional effort for the anisotropic evaluation, and this additional effort is eliminated by use of a small computer. The flexibility of the anisotropic procedure is greater because more than two independent elastic constants are available in fitting rock data. For the special relationship assumed among orthotropic constants, five independent elastic constants are available for the determination of in-situ secondary principal stresses as compared with two independent elastic constants for the isotropic model. Much of the material presented is either directly from the literature or adapted from the literature through superposition or the usual transformations. Consequently, only enough detail for clarity of presentation is included. RELATIONS FROM ANISOTROPIC ELASTICITY Materials that have three mutually orthogonal planes of elastic symmetry are called orthotropic. By directing the axes of the coordinates perpendicular to these planes, Hooke's law for an orthotropic solid 11 is

Jan 1, 1970

By M. J. Hordon, M. A. Wright

The well-defined increase in fatigue life observed o many metals cyclicly strained at vacuum levels below 10-1 to 10-3 torr has been attributed to the critical retardation of oxygen or water vapor chemisorption at the crack tip during crack propagation.1-3 In the absence of strongly adsorbed surface films, crack re-welding during cyclic compression or dislocation escape from the plastic zone around the crack tip has been proposed to account for the observed decrease in the rate of crack growth. The increase in the critical pressure required for the transition in crack growth rate with temperature experimentally determined for aluminum was found to be generally in accord with the adsorption rate model.4 However, although the adsorption mechanism would also predict an increase in transition pressure and fatigue life with increase in cyclic loading rate, and such effects were noted by Snowden5 for lead and Hordon3 for aluminum, the opposite results were reported by Kramer et al.B in studies on aluminum. The present note describes some recent measurements of the fatigue properties of 1100-H14 aluminum at low pressures to determine the specific effect of cyclic strain frequency in the transition pressure range. Flat cantilever-type specimens of 1100-H14 aluminum shaped to produce a uniform strain gradient along the gage length were tested in reverse plane bending at constant deflection amplitudes in two independent multi-specimen vacuum fatigue systems. One series of tests using 2-in. gage length specimens was conducted in an ion pumped apparatus with 107 torr and 50 cps capacity, denoted as Unit I, utilizing fixed mechanical cams to impose the strain amplitude. An independent test series using shorter 1-in. gage length specimens was conducted in a cryopumped apparatus designed for extremely low pressures below 10-10 torr, denoted as Unit II, using an electromechanical vibrator at non-resonant frequencies up to 150 cps to provide the deflection. Both vacuum fatigue units and associated test procedures have been described previously.3'7

Jan 1, 1969

By E. F. Bailey, L. S. Birks

The effect of stress on the austenite to ferrite transformation in carbon steel was studied by X-ray diffraction techniques. Tensile stress was found to cause reorienta-tion of austenite above the transformation temperature, to accelerate equilibrium conditions at the transformation temperature, and to cause precipitation of large carbides at a critical value of stress. IN the past, a number of papers' have discussed the effect of stress on the austenite to martensite transformation at relatively low temperatures. In general, it has been shown that tensile stress induces some transformation at a given temperature, while compressive stress retards the transformation. Very little work has been reported on the effect of stress on the transformation from austenite to ferrite plus carbide near the A, point in steel. One of the few papers in the literature2 reports an increase in A1 of about 1°C in pearlitic steel upon the application of tensile stress. In this paper, the effect of tensile stress on eutec-toid steel at, and above, the A, point was studied in

Jan 1, 1956

By W. D. Robertson, J. -P. Briant, M. Gell

The distribulion of dislocatiorls genevnted during the propagalion of hydrogen-induced cracks in Fe-Si cryslcrls was studied as a funclion of temperature f-110o lo 243°C) and silicorz conlenl (3.1 and 4.2 pct). It zoas found that the clislocntiotl densily and the size of the plctslic zone increased with increasing tempevalnre and decreasing silicon conlent. Furtheruvzove, there was a correlcrtion in the dislocalion patterns formed around cracks that propagated at different tempevattrt-es in cvyslals of diffevent silicon contents such that a 1 pcl itlcverise in silicon content was equivalent to a lemperaluore redziclion of approximately 120°C. The experimenlal YeSnllS were compaved with the results of an elastic-plastic wodel that relates the size of the pluslic .zone to the cvack length, internal pressure, and yield stress. it was found that the clzunges in the dislocctlion cryrays with lemperature and combosition can be e-kplaincd by the lemperatrnre and composilion dependence of the yield stress. An wmtsual feature of this study was the observation of low -temperature noncrystrrllogruphic cracks. PLASTIC relaxation can occur at the edge of a moving crack by the operation of pre-existing dislocation sources or by the creation of new sources in a region of perfect 1attice.l'2 The amount of relaxation in a given crystal depends on the crack velocity and the temperature, and can determine whether a crack propagates in a brittle or a ductile manner.1-3 Tetelman and Robertson4 observed microcracks m Fe-3 pct Si single crystals that formed on (100) planes by the precipitation of hydrogen gas during electrolytic charging at 23°C. The plastic deformation accompanying crack propagation was observed in the form of dislocation etch pits and an extensive analysis has been made of the size, shape, and crystallography of the dislocation arrays5-7 This paper describes the effect of temperature on the plastic deformation generated around hydrogen-induced cracks in Fe-3.1 pct Si and Fe-4.2 pct Si single crystals. The observations are compared with the results of an elastic-plastic model for yielding around a crack containing an internal pressure. 1) EXPERIMENTAL PROCEDURES The composition of the materials used in this study are given in Table I. Single crystals of alloy A and the 4.2 pct Si alloy were grown by the strain-anneal method; crystals of alloy B and the 5.1 pct Si alloy were cut from an ingot grown from the liquid. he ~ingle-cr~stal metallographic specimens had a Cross section of 0.100 by 0.050 in. with a length of at least 3/8 in. Specimens were annealed for 3 hr at

Jan 1, 1968

By d&apos, C. McCoul, C. Antonio, R. Krohn

MOST of the commercial colored gold alloys for jewelry applications are based on the Au-Ag-Cu-Zn system. Although work has been done on the constitution of the Au-Ag-Cu system.'-4 there are no reports in the literature on the effects of zinc additions in these alloys. We have metallographically determined the a =al + a2 transformation temperatures in 91/2- and 131/2-karat alloys in which varying amounts of zinc have been substituted for copper and silver. Samples were cast in the form of 1/2-in. round bars

Jan 1, 1970

By N. Rowlands, J. A. Finch, R. Espinosa-Gomez

The sulphation roast-leach process for complex sulphides results in phase changes due to roasting and leaching. The phases in the calcine, and in the neutral and hot acid leach residues were identified and their degree of liberation determined in order to design and Interpret separation tests on the residues. The hot acid leach residue was composed of hematite, silica, and lead sulphate with some associated silver. Magnetic separation was selected as the process for producing a lead concentrate, as the non-magnetic product. Separation was limited by -1 pm hematite reporting to the product, and hematite/lead sulphate agglomerates reporting to the magnetics.

Jan 1, 1984

By M. B. Ramachandra Rao

THIS paper records the results of the earth resistivity surveys made in the Godavari river in connection with the Ramapadasagar project. After describing the topographical and geological features of the area, the results of the investigation at the several sites have been mentioned. Further, a detailed account has been given of the resistivity methods adopted, the apparatus used and the interpretation of the curves. The resistivity measurements carried out over the water course have been specially outlined, and a review of the verification of the electrical indications by drilling in a number of cases, has also been presented.

Jan 1, 1947

By J. S. Falcone

Soluble sodium silicate materials have well known applications in flotation for desliming, selective depression and corrosion control. Recent advances in the understanding of the complex polymeric nature of silicate solutions using NMR spectroscopy, combined with our studies of the effects of polymeric silicate anions on metal ion activities in solution, oxide mineral surface charges and surfactant adsorption on clays are related to beneficiation processes. The results of these studies indicate the sodium silicates can be used to cause a solution chemistry and particle surface charge characteristics favorable to enhanced effectiveness in typical ore beneficiation systems.

Jan 1, 1983

By V. Leroy, A. G. Guy

Serious disagreements are often found between experimentally determined intrinsic diffusion coefficients and those calculated employing the usual form of the vacancy theory. In the new theory it is proposed that the total intrinsic flux, Ji, of component i, is the sum of a part, f, due to the usual random exclzanges of component i with the vacancies, and a second part, Ji, due to exchanges with the uacancies composing the net vacancy flux. The present treatment, while less powerful than that of Manning, has the advantage of easy uisualization and of facilitating the application of the vacancy-flux effect to complex systems. IT is becoming increasingly evident that there are serious deficiencies in the version of the vacancy theory of diffusion that has been widely used for the past 20 years. One type of evidence is the frequent lack of agreement between intrinsic diffusion coefficients and tracer diffusion coefficients, even taking account of the thermodynamic factor. A second kind of evidence is the observation of a Kirkendall shift larger than theoretically possible, that is, larger than can be accounted for without assigning a negative value to one of the two intrinsic diffusion coefficient.'- The thermodynamic factor could conceivably make both coefficients negative, but not just one. It is clear that a cause of these anomalies, apart from any inadequacy of the usual vacancy theory, might lie in an oversimplified treatment of the data. Adequate experimental techniques, including the use of moderate pressure during the diffusion anneal, are now available to insure that porosity, lateral expansion, and so forth, can be kept negligibly small in most cases. The effect of differences in atomic volume can be of major importance, and it is essential that one of the available methods4 be used to account for this factor. In the present treatment this is accomplished by the consistent use of moles per cubic centimeter as the unit of concentration. Of the various possible inadequacies of the vacancy theory, attention will be given here only to effects of the net vacancy flux. annin' has previously considered this question, beginning with an analysis of atomic jumping of tracer atoms. When he added the effect of a concentration gradient, new terms arose that could be associated with the flow of vacancies. The present treatment uses quite a different approach. The usual vacancy flux, J,, is introduced explicitly, and a simple analysis predicts major changes in the intrinsic diffusion coefficients from this cause. The usual assumptions are made that only a vacancy mechanism is operative, that the formation of voids can be neglected, and that changes in the partial molal volumes, vl and v2, are negligible. The significant diffusion coefficients for the present topic are Dl and D,, the intrinsic coefficients, which enter in the equations, where the flux Ji, moles per sq cm per sec, is that crossing the Kirkendall interface. The concentration, ci, is in units of moles per cu cm, and the concentration gradient, aci/ax, is evaluated at the Kirkendall interface. It will be recalled' that the calculation of Dl and D2 involves the measurement of areas on the diffusion curve with respect to the positions of the Kirkendall and Matano interfaces. In the case of the anomalies mentioned earlier, the Kirkendall shift is too large to be accounted for by the diiferetzce in fluxes (J2 -J1), given by Eqs. [I] and [2]. The logical inference is that the flux of the solvent atoms, J1, is actually in the same direction as the flux of the solute atoms, Jz. In terms of Eq. [I] this requires that Dl have a negative value. However, it would be somewhat misleading to state that the solvent atoms are diffusing up their own concentration gradient. The explanation that will be advanced here pictures competing processes producing the net flux of solvent atoms: 1) diffusion of the solvent atoms down their own gradient by random exchanges with vacancies; and 2) diffusion of solvent atoms in the opposite direction by exchanges with the net vacancy flux. ACTION OF THE NET VACANCY FLUX Theories of vacancy diffusion can be formulated with varying degrees of refinement, and the present theory has purposely been kept as simple as appeared adequate to explain the phenomenon in question. In particular the following aspects have been neglected: 1) the gradient of vacancy concentration in comparison to the gradient of the atomic species; 2) departure of vacancy concentration from the local equilibrium value; 3) variation of the jump frequency, LO, with the specific surroundings of the atom-vacancy pair being considered; 4) correlation effects. These and other refinements can be considered once the essential mechanism has been established. The essential idea of the present analysis is to calculate the total intrinsic flux, Ji, of component i as the sum, JlJ?±j{ [3] where J; is attributable to the usual random atomic jumping, and J{ is a contribution arising from the net vacancy flux, J,. The latter quantity, of course,

Jan 1, 1967

By D. F. Toner, P. E. Gage, D. J. Mack

MUCH work has been done on the decomposition of the p phase at the eutectoid composition, 11.9 pct Al, in the Cu-A1 system by Smith and Lind-lief,' Mack,' Klier and Grymko,3 Haynes,4 and others. In all of the mechanisms proposed by these workers for the decomposition of the ß phase, it was stated that the a phase must precipitate rich in aluminum with respect to the equilibrium composition of 9.4 pct A1 at 565°C. To check this hypothesis, it was necessary to have a master curve relating equilibrium aluminum content of a to lattice parameters of a. A number '' binary Cu-Al alloys of increasing amounts of aluminum were prepared by Ampco Metal Inc. These alloys, received as-cast, were given a 30 pct reduction of area by hot-working and then annealed at 900°C for homogenization and slowly cooled in the

Jan 1, 1956

By R. D. Nelson, D. H. Polonis

ThE eutectoid decomposition of 6 phase in the Cu-Sn system (32.53 wt pct Sn) has been studied by several investigators.1-6 On the basis of X-ray work, Iball and 0wen1 reported complete decomposition of 6 in powder specimens after 7 days at 300°C. Wang and Hansen followed the micro-structural changes during heat treatment of lump specimens and estimated 5 pct decomposition after 63 days at 300°C. Wang and Hansen suggested that the discrepancy between the decomposition rates of powder and lump specimens might be due to the excess surface free energy of powders. The present work involved 6 decomposition in copper-tin alloy powders containing 32.6 wt pct Sn. Alloy lump specimens exhibited entirely 6 phase after fairly slow cooling (air cooling) from above 350°C and were so brittle that they could be easily crushed to-200 mesh in a percussion mortar. X-ray diffraction study of the as-crushed powders (-200 mesh) revealed 100 pct 6 phase with very slight line broadening effects due to strain introduced by crushing. Only 6 phase was detected by X-ray diffraction in powders which were heat treated 4 hr at 450°C and air cooled to room tem-

Jan 1, 1960

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases extend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1980

By J. W. Pugh

PREFERRED orientations in cold-rolled body-centered-cubic metals appear to have remarkable similarity. The as-cold-rolled textures in iron,1,2 silicon-iron,3 mild steel,4 molybdenum, vanadium,&apos; chromium,&apos; tantalum,&apos; tungsten,&apos; and a-zirconium-niobium alloys10 have been determined. These textures have, in some cases, been represented by congrUOUS pole figures and have all been described in one or both of two ways. They have frequently been reported as predominantly (100) <011> orientation

Jan 1, 1959