Search Documents

By Henry Fay

THE erosion of guns is a complex problem which can be solved only by a detailed study of all the factors involved. In the present paper it is proposed to submit the results of observations and experiments which have extended over several years. Certain facts have been established and preliminary reports have been published.' Conclusions have been reached since then which, it is believed, are worth presenting for the purpose of promoting discussion, and with the hope that ultimately the whole truth will be known. The particular phase of the problem which will be presented here is the hardening of the inner surface of the gun tube. It has been known for a long time that after firing a large caliber gun for some time, the surface of the metal becomes hard and brittle, cracks, and wears away.2 The character of this phenomenon may be learned by an examination of some results which are typical, obtained from a detailed study of a 12-in. gun. The gun was trepanned and rings representing various sections of the gun were cut out for examination. The first ring represented the metal at the muzzle end, and the other rings were removed at approximately 120, 240, 325 and 337 in., respectively, toward the breech end. The appearance of the surface of the metal in the different sections is shown in Fig. 1. The greatest amount of wear and maximum amount of hard surface layer was found in section marked E, which is nearest the powder chamber and at the beginning of the rifling; the maximum amount of cracking in D; the maximum amount of copper deposition in C. Section B showed heat cracks on both lands and grooves, and section A showed heat cracks on the driving edge of the lands only. There was much flow of metal in both sections E and D, and there was progressively less effect noticeable toward the muzzle end. The polished cross-section of these same pieces is shown in Fig. 2. The

Jan 12, 1916

By R. J. Mechin

IN the early part of 1934, the St. Joseph Lead Co. purchased from the Kadco Corporation three dust-removal units, two suitable for raise work, and the other for drifting operations. The equipment was installed at the Balmat mine, in St. Lawrence County, New York. The Kadco dust-control system can be briefly described as one in which hoods, through which the drill steel is drawn, control the dust at the drill hole, the dust is conveyed through rubber hose or pipe to a collector, where it is removed from the air stream, and the air is then available for recircula-tion in the working place. As during the last few years a number of studies had been completed for the purpose of determining whether or not the dust was effectively removed by the Kadco system, and as the dust counts taken in these tests apparently indicate that it was, the St. Joseph Lead Co. was only inter-ested in obtaining data to show the efficiency of drilling, expressed in terms of minutes per foot drilled, when -using Kadco equipment, in comparison with the former method of drilling dry in a raise and drilling wet in a drift. Comparative dust counts were taken at Balmat, however, by the Metropolitan Life Insurance Co. to show the difference in the dust content of the air in which the operators worked when drilling dry, wet, or with the Kadco equipment.

Jan 1, 1935

Teamwork: The famous first sentence of an essay en- titled Aphorisms, by Hippocrates, is as follows: "Life is short, the Art long, opportunity fleeting, experience treacherous, judgment difficult." The future of science does not depend so much on the number of scientists or the number of colleges, but rather on the individual qualities and the degree of perfection of a limited group of leading scientists and colleges. These are individual factors which require inherent talent which in turn is a condition evolved after generations of culture. Thus, very elaborate higher education for indiscriminate masses of humanity or students may not necessarily show the expected results. In other words, it is possible that higher specialized education should be given only to the few talented individuals, and their capacity and worth should be judged by as highly qualified and talented teachers. Quality is the greatest of all competitive aids. An essential qualification that must be possessed by a quality mineral industries college is a high caliber teaching staff, for the mineral sciences will advance in the coming years only if the leading minds of today are made avail- able as the mental springboards for our scientists of tomorrow. Mineral industries schools are finding it increasingly difficult to maintain a high caliber staff of instructors and administrators in competition with private business and governmental demands for similar

Jan 1, 1950

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By Raymond D. Sloan

Development and exploration in Oklahoma showed a definite increase in 1941 over 1940 in production, wildcat activity and total well completions. Geological and geophysical work continued and possibly increased slightly in amount. Oklahoma retained third place in the ranking of oil-producing states of the nation, topped only by Texas and California, and followed by Illinois in fourth position. Production averaged 416,800 bbl. daily, a 1.7 per cent increase, as compared with 409,900 bbl. daily for the year 1940. Maintenance of the state's relatively stable producing rate resulted from the discovery of numerous small pools, the recombing of old areas, the establishment of new producing horizons, and the drilling of an increased number of marginal wells. The market for the Mid-Continent crude was strengthened materially to meet the increased demand. Coincident with a deeline in production in Illinois, shipment of Oklahoma-Kansas crude to the eastern points averaged 453,000 bbl. per day, an increase of 49.4 per cent as compared with 1940. The movement south amounted to an average of 42,000 bbl. per day, a loss of 41.7 per cent. Secondary-recovery programs in Oklahoma were given more consideration, operators realizing that in the future many pools would necessarily have to resort to this type of operation. Five permits for water-flooding were issued by the Corporation Commission during the year. These projects were in Rogers, Wagoner and Nowata Counties, in the shallow northeastern area, which has relatively extensive development of this type in the Bartles-ville sand at from 600 to 1000 ft. in depth. Gas repressuring of an individual lease in the 35-year old Glenn pool, Creek County, proved relatively successful, and after a year's operation was extended to cover a much larger area, with several operators participating. More of this type of work is expected in the future; however, it was given an initial setback when the legislative proposal authorizing secondary recovery in the Wilcox zone of Oklahoma's largest pool, the Oklahoma City pool, was pigeonholed by the committee. A continuation of the low discovery rates within the state would possibly lead to a revival of interest in the project. Many pools formerly classified as prorated areas were removed from this classification and transferred into the group of settled production. At the close of the year the issuance of the Federal Conservation Order M-68 and the interrelated Preference Rating Order P-98 caused a sharp decline in drilling operations, which is expected to continue until such operations are stabilized at a lower rate. The ultimate effect of these two orders on discoveries, production and reserves is a matter of speculation and conjecture. During the year, 2110 new wells were drilled, an increase of approximately 18 per cent as compared with the previous year. Of the total, 1235 were oil wells with a combined initial potential of 342,754 bbl. daily, 178 were gas wells with a total

Jan 1, 1942

By H. L. Bilhartz, H. F. Dunlap, C. R. Bailey, Ellis Shuler

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent 'saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge's paper.' In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01' the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By C. R. Bailey, H. F. Dunlap, Ellis Shuler, H. L. Bilhartz

Data are presented which indicate that the saturation exponent, n, in the equation, R. = R100S-11, relating core resistivity, I:,. to the resistivity at 100 per cent saturation. R100. and to the saturation, S. may vary appreciably from the value of two which is usually assumed for this exponent when interpret ing well logs. Values ranging from one to two and one-half have been found on (.ore sample investigated to date. Attempts to correlate this saturation exponent with porosity or permeability of the core have not been successful. The saturation exponent is apparently not a function of the interfacial tension between the brine and the displacing fluid. Some evidence is given indicating that the resistance of the core is not a unique function of the saturation but depends upon the manner in which this saturation was achieved. Equipment and technique are discussed for measurement of resistivities in core plugs in which water saturation can be varied. lNTRODUCTION A number of investigations of the resistivity-saturation relationship for un-c~~nsolidated sands and consolidated (.ore samples have been reported in the literature. According to most of these: R. = R¹ººS², where R² = the resistivity of a formation at saturation S, and R¹ºº= the resistivity of the formation at 100 per cent water saturation. Much of this work was (lone on unconsolidated sands desaturated by gas or oil. Hen-clerson and Ynster worked exclusively with dynamic systems, flowing oil or gas through consolidated cores. There is some doubt as to how well this reproduces static reservoir conditions. Jakosky and Hopper³ onsidered also the case of consolidated core plugs, but the oil-water distribution in the emulsions which they used to saturate their cores is almost certainly different from that occurring in reservoirs. Recently Guyod quotes the results of some Russian work which indicates that n may vary from 1.7 to 4.3. No experimental details of this work are available. In connection with electric log interpretation it is important to know the value of the saturation exponent. For example, if in a given reservoir it is found that the resistivity is three time.; the resistivity observed when the reservoir is 100 pel. cent 'saturated with water, this fact would be interpreted as indicating a water saturation of 33 per cent if the saturation exponent were 1 and a water saturation of 6-1 per cent if the saturation exponent were 2.5. EXPERIMENTAL METHOD In the work to be described it was assumed that reservoir conditions are most nearly obtained when core plugs are desaturated by the capillary pressure technique referred to in numerous places in the literature, as for example. in Bruce and Welge's paper.' In this technique the core. saturated 100 per cent with brine, is placed in contact with a ceramic disc permeable to brine but not to the displacing medium for the displacement pressures used. Pres-ure is then applied to the displacing medium and brine forced out of the core through the ceramic disc. Fig. 1 shows the core plug in place in the cell in which resistivity and saturation measurements are made. Fig. 2 shows the schematic electrical diagram wed to make resistivity measurements on the core plug. A four-electrode type circuit is used, employing a Hewlett-Packard model 400A. AC vacnum tube voltmeter. The 60-cycle AC current througli the core is adjusted to 1 milliampere and measured by noting the voltage drop across the calibrated 100-ohm resistor. The vo1tages appearing at probes 1, 2, 3, and 4 are then successively measured. Voltage drops across the top, center, and bottom portions of the core are obtained by sublracting the voltages appearing at successive probes. This technique avoids any polarization or other high contact resistance phenomena which may develop at the current input electrodes. Resistances which may develop between the core and the probes, and which are small compared to the 1-megoam input impedance 01' the vacuum tube voltmeter will (obviously not affect the measurements allpreciably. Any very appreciable resistallces which may develop at any of the probe wires are detected and allowed for by inserting a 1-megohm resistor in series with the voltage measuring probe. If the probe resistance is actually zero, the new voltage measured after insertion of the I-megolim resistor will be approximately one-half of that previously measured. since the input impedance of the vacuum tube voltmeter is itself 1 megohm. If an! appreciable probe resistance has developed, the new voltage is found to be appreciably greater than one-half of the previously measured voltage. Such probe resistance; have been found to develop only occasionally and usually can be traced to poor connections betwern the core

Jan 1, 1949

By Floyd Kelley

THERE is an ever-increasing demand for furnaces with controlled atmosphere, due to the large quantities of steel being used in the automotive industry, such as the .high-chromium stainless irons, the 18 Cr, 8 Ni stainless iron and low-carbon steel sheets. The difficulties involved in the annealing of such materials, if they are to be kept absolutely free from oxidation, are many. It is possible to bright-anneal these steels in small laboratory hydrogen furnaces, using specially purified hydrogen and taking some additional precautions. In the first place, the insulation, usually of alumina or magnesia, holds small amounts of water vapor, which it is almost impossible to remove completely. Secondly, there is always condensation of water vapor in the cooling chambers of such furnaces, and with the continuous circulation of the hydrogen gas in the furnace, the water vapor is carried from the cooling chamber back into the heating chamber. This water vapor oxidizes the charge. Lastly, the supply of moisture is made sure by the diffusion of small amounts of air from the atmosphere into the furnace against the pressure of the hydrogen. The oxygen combines with the hydrogen and forms more water. Under such conditions there is, little gained by using specially purified gas, because it becomes contaminated after reaching the furnace.

Jan 1, 1931

By L. A. Walker

DURING the past twelve years the underground shaft of the United States mine at Bingham has been sunk an additional 2000 ft. with stations and pockets cut every 200 ft. without interrupting the mining of 600 tons of ore per day and the advancing of 1500 ft. of development per month. Following is a brief description of the way the joint work is conducted. The vertical underground shaft is a three-compartment shaft with outside dimensions of 6 ft. 4 in. by 15 ft. 6 in., and inside dimensions for each compartment of 4 ft. 2 in. by 4 ft. 8 in. The manway compartment of the main shaft is used as the hoisting compartment in sinking operations; it is partially lined with 2 by 12-in, lagging and a bucket is used without guides or crosshead. Preparatory work includes the placing of a bulkhead in the manway compartment, 60 ft. above the lowest station or level, the installation of a hoist, a head sheave, a fleet sheave, a-signal system, air and water lines, and a trap door for handling waste.

Jan 1, 1937

By A. M. E. Eilers

No one who has visited our Western mining districts, and studied the economical part of the beneficiation of the ores occurring all over that vast extent of country, can underrate the high importance of the above subject. By far the larger number of the districts which contain smelting ores, i.e., argentiferous and auriferous lead, or copper ores, are situated in the Great Basin, that great plateau between the Rocky Mountains on the east, and the Sierra Nevada on the west, almost the whole of which is comprised at present in the boundaries of Nevada, Utah, and part of Arizona. This region is essentially a barren country. The extreme dryness of the atmosphere permits but a scanty vegetation in the plains ; and even in the detached mountain-chains running through it-generally from N. to S., or from N. W. to S. E.-there are no trees found except dwarfed pines and mahogany, at the head of sheltered ravines, and a few cottonwoods and willows, which fringe the insignificant streams, before the water sinks in the arid plains. Nearly all the mountain-chains in this region are rich in silver ores. That class of these ores which is adapted to amalgamation, and rich in silver, has been worked with profit for more than ten years. But before the advent of the transcontinental railways, mining was restricted to these ores alone, and the consumption of fuel could be met with the scanty supply of forest trees in the immediate vicinity of the mining districts. Since, however, the Union and Central Pacific Railroads have brought the Great Basin nearer to the commercial centres of the East and the Pacific coast, thus reducing the expenses of freight and labor materially, other silver deposits, containing poorer ores in greater abundance, have been rapidly taken

Jan 1, 1873

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By Norman Gerald

THE lack of a continuous operating balance in petroleum refining, which is analyzed in this paper, is by no means a feature solely of this division of the oil industry. Serious disequilibria of a capital as well as an operating nature exist both in the producing and marketing departments, while problems in the former and to some degree the latter are complicated by political involvements. Attention has previously been directed to the unstabilizing influence of present proration formulas in stimulating unnec-essary drilling.1 While equilibrium in petroleum refining operations has been fairly well maintained in the past decade, examination of departures may prove fruitful. Economic analysis is the application of time and motion study to the functioning of management, rather than labor. Properly applied it may reveal changes in policies that would increase the utility of the properties and facilities of the industry for stockholders, employees and the public, while contributing a stabilizing influence to the general economy. The study of economic equilibrium is essentially one of measurement and interpretation, requiring adequate data and the development of a tech-nique of analysis that employs statistical and mathematical methods as a supplement to the broad descriptive phase of economics. Economic equilibrium in petroleum refining is a dual concept. It embraces both the over-all balance between total storage and total demand for major products and the internal balance between the demands and inventories of the various products. The latter is the more complex of the two for it is concerned with proportionating the supplies of the several products stemming from the joint source to the demands for the individual products which are subject to wide variations. All the products are essentially nondurable goods, and they are used both by producers and consumers but in varying proportions. Motor fuel is very largely a consumer's good, while residual fuel oil is almost entirely a producer's good, the other products falling between these extremes. The peculiar-

Jan 1, 1939

By I. J. Lin, A. Mitzmager

This paper describes a series of experiments conducted to determine how the physicochemical properties of the suspending fluid affect the size reduction of quartz in a ball mill. Particular attention was directed toward the differences in rate of grinding and particle size distributions when either polar or non-polar fluids were the suspending liquids. Grinding was performed with water, carbon tetrachloride and methylcyclohexane as the liquids, and also in nitrogen for comparative purposes. From the results ob- tained, the authors have concluded that the presence of water greatly enhances efficiency in the grinding of quartz. Comminution is generally regarded as a purely physical process in which fragmentation of a solid is obtained by the application of suitable forces. In 1944, however, Rehbinder et al.1 pioneered the idea that the interfacial forces between the solid and the media plays an important role in comminution. Since then, a number of researches have shown conclusively that comminution is affected by surface chemical phenomena,2-5 and Gaudin went as far as to compare comminution to a chemical reaction.6 The effect of the viscosity and the density of the fluid media in grinding was also investigated, but

Jan 1, 1969

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

By E. P. Pfleider, W. D. Lacabanne

ROTARY-percussive drilling is a new method of drilling hard rock. Designed to give variations in thrust, revolutions per minute, and torque ranges, these drills combine the high efficiency of the rotary system in soft rocks with an increasing amount of percussive action in rocks more difficult to fragment. Fundamentals of the rotary, percussive, and combination systems have been described in detail in various papers-most recently by C. Fairhurst and W. D. Lacabanne1-but there is still much basic work to be done on the interplay of actions in the rotary-percussive system to enable the drill designer to achieve the highest efficiencies. Whereas the original units struck light blows of only 15 to 30 ft-lb, adequate for medium hard rocks, the present trend is to piston blows of 50 to 65 ft-lb in order to cope with the granites and other rocks having Shore hardnesses of 75 or more.

Jan 7, 1957

The earliest record of production in this county is for drilling a salt well in 1809. Some scattered data are shown in the table; the total figures are estimated. Little coal could be shipped in this period on account of lack of transportation. [ ]

Jan 1, 1942

By Edward C. J. Urban

The nature of certain pernicious dusts commonly encountered in the removal of iron ore from the underground mines of the Lake Superior district is recognized, and appropriate measures for the protection of individuals subjected to these dusts have been applied in most mines for more than 10 years. Undoubtedly the principal concern has been demanded by dusts that contain as a constituent silicon dioxide in its free or uncombined state, the mineral we all know as quartz or chert. Investigators1 agree that among the factors that determine injurious exposure are: the composition of the dust, the concentration suspended at the breathing level and the duration of the exposure. We have on hand data that describe the experience of several underground iron-ore mines in the Upper Peninsula of Michigan and Wisconsin in regard to these factors, which in a large measure also reflect the general experience of the other mines of the area. We believe that a discussion of these data will indicate the effectiveness of the dust-control methods that have been considered good practice and that have been employed over a long period of time. A silicosis-prevention program was ini- tiated by the iron mines of the Upper Peninsula in 1934 and records of mine dustiness are available from that date to the present time. For dust conditions previous to 1934 the results of observations conducted in other industries can be utilized together with local information pertaining to the development and initial application of rock-drilling equipment. Development of Rock DriI,I.s Thc earliest percussion rock drill that later had any industrial use was patented in this country in 1851.2 This machine was later modified and improved in many respects but its Piston-Type design remained standard for drilling equipment in most mines for the next 63 years.3 The piston drill was operated either by air or by steam. It employed a solid drill steel, fastened directly to the reciprocating piston. The drilling was done dry except in holes directed at an angle below the horizontal. For these water was manually injected into the hole and the pumping action of the rod expelled the sludge. The dry cuttings from drillings inclined above the horizontal fell from the hole by their own weight. A development of major importance from the standpoint of dust generation and control occurred with the invention by J. G. Leyner of a hammer-type rock drill that embodied the essential feature of a drill steel with a hollow core. His patent was secured in 1897. The machine was a radical departure in drilling method. The steel was held loosely in a chuck while

Jan 1, 1949

By W. M. Rust, W. D. Mounce

THE almost universal acceptance of electrical logging by the petroleum industry calls for a critical examination of the physical bases of the common methods. This is particularly needed for the natural potential log. The conventional explanations are based on the phenomena of electrofiltration and electro-osmosis. However, experimental data show that they fail to give a basis that is quantitatively sound. Moreover, they lead to interpretations of details of electrical logs that are erroneous. It was found experimentally that when a plug of shale is placed in a chain of dissimilar electrolytes, a current flow results. Experiments on oil-well cores and fluids similar to those existing in wells show that potentials are set up which are in reasonable agreement with those encountered in electrical logging. Doubt- less other sources of potential are important but this explanation not only accounts for much of the potential but also clarifies some fairly familiar examples of misinterpretations.

Jan 1, 1944

By T. D. Teimann, R. L. Stone

The rate of extraction of silica from certain Wisconsin and Minnesota taconites was investigated by autoclave digestion in sodium hydroxide solutions over the temperature range from 296° to 416°F. Rates obtained were from 7 to 254 g mol per cm2 per sec giving activation energies from 15,000 to 19.000 cal per mol. Activation energy was found to increase with increase of sodium hydroxide concentration. Digestion of different forms of quartz indicated the rate of extraction to be solely a function of surface area under similar conditions of digestion. The results of an experimental investigation on the caustic extraction of silica from certain Wisconsin and Minnesota taconites were presented in a recent publication.' It was shown that residual concentrates containing as much as 65% iron can be produced by this method. The occurrence of silica as a micro-crystalline variety of quartz with high specific surface area gave correspondingly high mean rates of extraction in solutions of sodium hydroxide. The present paper extends this previous work by presenting the results of a study of the specific rates of extraction of silica from these ores as related to temperature, sodium hydroxide concentration and variety of quartz. Calculated activation energies for the dissolution of silica are presented and some possible mechanisms are discussed. TACONITES The low-grade siliceous iron ores investigated included taconite from the Wisconsin Gogebic range and a semi-taconite2 from the Minnesota Mesabi range. These are adequately described in the former paper1 and by the U. S. Bureau of Mines. The principal iron minerals are hematite (Fe2O3) and goethite (Fe2O3 . H2O), while the gangue is essentially a microcrystalline variety of quartz. Minor amounts of other minerals are present. Typical analyses show the Wisconsin taconite to contain approximately 28% Fe and 54% SiO2 and the Minnesota semi-taconite 39% Fe and 39% SiO2. Analyses of the actual samples used are given in Table I. The taconite samples were prepared for digestion by reducing the original ore to minus 200 mesh in a Braun pulverizer. QUARTZ Three varieties of quartz were studied in the investigation: Ottawa sand, chert and chalcedony. The Ottawa sand was obtained from the Ottawa Silica Co. The chert and chalcedony came from Wards Natural Science Establishment. A minus 200 plus 400 mesh fraction of the Ottawa sand, used as a surface area standard, was repeatedly washed in hot concentrated hydrochloric acid followed by distilled water before autoclaving. The other two varieties were used directly after grinding through 200 mesh in a laboratory hammer mill. Analyses of these samples appear in Table 11. Microscopic examination of the silica samples by the oil immersion method showed that the Ottawa sand consisted of clean, uniform spheres of quartz with little deviation in size from a mean diameter of 82µ determined by a distribution count. The other two varieties consisted almost entirely of microcrystalline aggregates of quartz crystals; the aggregates ranged from 10 to 70µ. The individual crystals in the chert aggregates were estimated to be of the order of

Jan 1, 1964

By William Brewster

DATING back some five years ago, various foundries made inquiries as to the probable total carbon content in a given specification and grade of pig iron. Up to that time we had no data, and except for a few occasional determinations of total carbon, no attempt had ever been made to set up routine determinations of total carbon. In fact, at that time, a cast analysis was considered sufficient, without examining at further length into possible variations of analysis between ladles of the same cast. In view of the various inquiries as to total carbon, we sampled all piles of all grades of pig iron, making complete analyses. Finding some variation in carbon content, we secured more samples and plotted the carbon content with respect to silicon in each grade of iron except for the higher phosphorus foundry iron, where it was necessary to divide the group into twenty-point phosphorus ranges. This is easily understood, owing to the falling off of carbon content with the increase in phosphorus con-tent, silicon in each case being the same. In addition, these curves clearly demonstrate the lowering of the carbon content as the silicon is increased. In order to insure accuracy and reliable determinations the following method of sampling and analysis was employed: Two pigs selected from each end of the car, each car containing iron from one 50-ton ladle, are drilled with a 5/16-in. drill all the way through from top to bottom in the center of one section of the pig. The drillings are collected and transferred to an 80-mesh sieve; the portion passing through and the portion retained are placed in separate envelopes and labeled accordingly. The amount of sample in each envelope is weighed to obtain the proportionate amount of coarse and fine drillings, then a factor weight of sample (1.3636 grams) made up of proportionate

Jan 1, 1936