Search Documents

By B. Trafton, H. L. Hartman

An earlier paper1 introduced a rapid solution for mine ventilation network problems, employing the digital computer. In this paper, refinements and additions to the computer program which expand its scope of application and a solution to a ventilation network having a coal-mine configuration are presented. The revised program-written in FORTRAN for the IBM 7074 computer in Penn State's Computation Center-is applicable to any mine ventilation network employing natural splitting and having its fan located externally. It accomplishes the following: 1) Distributes an assumed total quantity of air flow among all airways of the network, performing iterations until an acceptable level of error is attained and the flow in each airway is known. 2) Computes the pressure drop (head loss) in all airways and the overall network and mine head losses. 3) Determines the operating point for the mine and a given fan, adjusting all air flows and head losses to the actual values. The basis of analysis used is the Hardy Cross method of successive approximation for solution of any fluid network, explained in detail in the earlier article. In brief, corrections to assumed air flows are computed for all the loops of a network; following distribution to the airways of each loop, the process is repeated until acceptable accuracy is attained. When a hand or desk-calculator solution is used, there is advantage to close approximation of the actual flows in the original assumption of air-flow distribution in the network. Since publication of the previous paper, in which assumption of initial quantities was also necessary in the computer solution, the program has been modified to make the first distribution itself, assigning the total quantity to one specified path in a split and then proceeding to correct the flows. The number of iterations required for a high-accuracy solution is little affected, at least in networks of few loops, 10 to 15 being sufficient to reduce the error to 1 pct or less. The principal limitation of the original program was that it contained no provision for handling a fan. Further, it did not determine the overall head loss in the network and was not designed for multiple parallel openings, such as occur in coal mines. The revised program was written to overcome these disadvantages and also to print out the adjusted flows for all airways, corrected for the system operating point. At the present time, the program can handle only an external fan. The procedure employed in solving a ventilation network is now as follows: 1) Input data consisting of airway characteristics and loop designation along with assumed direction of flow, for each branch of the network and any trunk airways, are fed into the computer. 2) Employing the resistance relationship, where R is resistance, K is friction factor, P is perimeter, L is length, A is area, and n is number of airways (where multiple intakes and returns are employed); values are computed for all airways. 3) An arbitrary, continuous route of flow through the circuit—from beginning to end—is selected and the path identified by airway numbers and read in. 4) Based on a total assumed quantity of flow Q (usually 100,000 cfm.) the computer employs the procedure described in the previous article in distributing quantities of flow among all the airways until a satisfactory level of accuracy has been attained (in the current program, the machine is turned off when the cumulative corrective error in cfm, is reduced to five times the number of airways). 5) Airway head losses H are calculated by the relation H = R Q2 and cumulated along the original designated flow route to find the overall head loss for the network. Trunk airways are then included to obtain the mine head.

Jan 1, 1964

By George Smith

THE discussion of production control at the Insti-tute's annual meeting was profitable in that it started some thinking. One pertinent question there raised was how the opening of new mines, whose now unneeded output would inevitably react on prices, could be postponed until the market was ready to ab-sorb their output. In transportation some restraint is being exercised on building new and unneeded fa-cilities, but in production no general solution of the problem has been offered. Yet in a special field of new development of increasing importance a quick and easy solution has been suggested. I refer to the leasing of mineral deposits on the public domain. The report of the United States Coal Commission says: "In its possession of approximately 60,000,000 acres of public coal lands the Federal Government has its own responsibility in restraining overdevelopment. The Department of the Interior, which has control of these lands under the leasing law, construes the law as giving the department no discretionary right to refuse applications for leases regularly made by qualified citizens or corporations for coal deposits on the pub-lic domain. It presumes, that the applicant believes there is a need for an additional coal mine in his local-ity and expects to find a market for the coal produced. Overdevelopment, however, is a fact in the West as well as in the East, and wherever present involves needless investment and excessive costs of operation. Plainly, the leasing law should be so amended as to give the executive department full discretion in its approval of the opening of a new coal mine on the, public domain, making that approval contingent on the showing that the new mine would serve the in-terest of the consuming public." A similar view of the Federal Government's re-sponsibility in restraining overdevelopment of its oil lands has been presented by the Federal Oil Conser-vation Board. The leasing law vests little or no dis-cretion in the Secretary of the Interior, who must grant a lease to a qualified applicant regardless of any obvious country-wide condition of surplus produc-tion. This wide-open invitation to exploit and dissi-pate the people's own oil resources could be restricted by simple legislation, although as remarked by the board, such a legislative remedy for a plain economic ailment "does not evoke popular support when its purpose is avowedly to put the brakes on development of natural resources."

Jan 5, 1928

By A. D. Kennedy

No major breakthroughs in concentration technology were made during the year, but solid advances were made in engineering. Perhaps the most significant was the growing acceptance of the unified or "systems approach" to mineral extraction, processing, refining, transportation and marketing. Under the systems approach, transportation is no longer some- one else's business, but a high cost item within the planning engineer's purview. The Savage River pipeline 1,2 and the Marconaflo process3,4 for land and ocean transport of iron ore slurry, are examples showing that evaluation of transportation as part of a unitized system can lead to innovation, and the determination of the physical location of some of the operations. There is even speculation that the cost reductions possible by ocean transport of iron ore slurry may bring in more plants using direct-reduction steelmaking processes.4 Some perennial problems can be solved by application of the systems approach; for example, under this concept the replacement of three small shovels in the pit with two larger shovels is not permissible on the basis of lower operating costs; the resulting change in ore blending upon metallurgical performance must first be evaluated to prove whether or not the change is economically beneficial to the entire operation (perhaps new storage-blending facilities will be indicated).

Jan 1, 1970

By Albert W. Giles

The splitting of the coal by partings is a familiar feature of many coal beds. The partings are normally argillaceous, more rarely sandy or calcareous. The material is usually fine-grained, less frequently coarse-grained to conglomeratic. Many partings are wedge-shaped, others are lenticular, and in some coal beds thin partings but one or two inches thick persist as thin sheets throughout areas of regional extent. The origin of the partings differs, and in some cases is obscure and uncertain. Origin of Thick Partings Wedge-shaped Partings Wedge-shaped partings are normally of indefinite linear extent but of short transverse section. They are developed adjacent to the borders of the original peat-forming swamp or around islands formed within the swamp, hence their presence is indicative of the approximate limit of the coal bed or of an interruption in the continuity of the coal bed. Following deposition of the parting gradual reestablishment of swamp conditions is followed by burial of the parting with accumulating peat. Partings developed adjacent to the borders of swamps normally thicken toward the periphery of the swamp and represent either detrital materials carried in from adjacent land areas during floods or materials carried in by advancing waves and currents after a barrier confining the swamp had been breached by the waves. Partings formed in the manner first mentioned should become coarser and more arenaceous toward the source of supply of the detrital materials, and the overlying and underlying coal should gradually grade into carbonaceous shale as the margin of the original swamp is approached. Partings formed by advance of waves across a barrier should be largely or entirely arenaceous, thin wedges of short longitudinal section, possibly with fossils of marine or brackish affinity. The subjacent coal normally should "pinch out" against the barrier, and the overlying coal continue to the barrier, or even extend across it, depending on the geographic conditions established following the breaching of the original barrier. Islands may be formed in swamps in a number of ways. They may represent local uplift of the swamp floor during earthquakes, or

Jan 1, 1934

By Byron E. Eldred

Generally speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. yet these other arts show quite plainly that a thermal-value basis alone is not sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other, arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a

Jan 1, 1911

By W. J. Keep

We have found that our graphic representations were, in some cases, not perfectly understood. In the tables by which we illustrate all our tests, the records appearing in the vertical columns between the rulings are the results of the tests of iron having the percentages and characteristics noted at the top of the column. The record is made by a short horizontal line in such vertical columns. It is located in horizontal spaces, which divide the table into units of measure, to indicate the value of the record. For example, in the upper part of Table VII. is recorded the transverse strength of the series of tests with white iron and aluminum, which were reported in our former paper. The numbers at the extreme top are the test-numbers. The fractional numbers below are the percentages

Jan 1, 1890

By S. P. Kinney, A. J. Boynton

THIS paper is not the result of recent research with regard to any particular feature of iron metallurgy, blast-furnace practice or mechanical engineering. It is rather a series of notes with regard to contemporaneous progress in blast-furnace construction and operation, together with some suggestions as to changes and improvements that seem to be desirable. On April 1, 1930, a committee of the Chicago District Blast Furnace and Coke Association presented to that association a rather ambitious study of blast-furnace equipment, together with recommendations for the design of construction of a complete blast-furnace unit for the production of 1000 tons of pig iron per day. This report represented the result of months of study by members of the committee, all of whom were actively engaged in operation or design of blast-furnace plants. It is natural, therefore, that comments on the present state of the art should take this 1000-tons furnace, as recommended by the Association, as a basis for comparison with corresponding features of construction or design. See Table 1. In looking through this report at the present time, the significant difference is in the nature of the gas-washing equipment that today would be specified. In other respects, the installation would remain generally very much as it was outlined in 1930. The change in furnace dimensions would be very slight and of no especial significance, except with respect to changes in stock-line diameter, of which more will be said hereafter. The high-efficiency stove as developed by various designers is thoroughly described within this report, and few changes have taken place since. Blowing equipment shows refinement and reflects the improvement in steam engineering. Hoisting and charging equipment and ladles for the conveyance of iron and slag remain, in general, as they were in 1930. In accordance with a general tendency

Jan 1, 1935

By W. M. Clark

OUR interest in the matter of pyrometers and pyrometry is primarily that of a user of considerable quantities of heat-measuring equipment; and while we play be somewhat critical on the subject we have aimed to make the nature of these comments constructive. The glass industry in America dates back to 1609, when Capt. John Smith started a small glass plant near Jamestown, Va., with a few Italian workmen, to manufacture glass beads for trading with the Indians. While the industry has expanded until it has reached a volume of over $200,000,000 per annum, the means of heat determination in Colonial days was the human eye, and in much of the industry the same means is used today. About 15 yr. ago the largest glass-house supply dealers began to sell platinum pyrometers, but as nearly all of these proved un-satisfactory, pyrometers met a temporary rebuff from the old-time glass manufacturers. As their ruggedness of construction, reliability, and stability have been improved, however, pyrometers have gradually won their way into more and more extensive use throughout the glass trade. But there are still many applications where pyrometers are not used, largely because of cost and upkeep considerations. There are two distinct fields in glass works for pyrometry. The first calls for accurate temperature measurement and the second only demands knowledge of relative comparative fluctuations of temperature, to know whether the work is becoming hotter or colder. For example, in a lehr for annealing glassware and removing strain we want accurate temperatures to know that the ware is heated to the critical temperature for rapid removal of strain. On the other hand, in a glass pot furnace nearly 120 ft. (36 m.) in circumference, where the pyrometer couples only project inside the furnace wall for less than 2 in. (50 mm.), it is inconceivable that these few inches represent the accurate temperature at every point of the 120-ft. circumference but the relative readings as to whether the pyrometer shows schedule temperature fluctuations are valuable indications for control. The glass melting in the pots is,

Jan 8, 1919

Since the comprehensive review of the Persian fields presented by Sir John Cadman last year, operations have proceeded normally. No developments of especial importance fall to be recorded and it remains only to bring up to date the full information given at the beginning of 1933. Controlled production from the Masjid-i-Sulaiman and Haft Kel fields has been maintained at slightly higher rates than during 1932. The figures for the past five years are as follows: These represent crude oil and products piped to the coast but exclude products reinjected into the reservoir, a process that has been in continuous operation at Masjid-i-Sulaiman during the period under review. The systematic delimitation of the Haft Kel field has been continued during the past year and results have been sufficiently encouraging to justify the inception of a wider scheme for distribution of production. Drilling has been resumed recently in the Persian sector of the Naft Khaneh field, and preliminary survey work is in progress for the selection of a site for a refinery at Kermanshah arid the construction of a connecting pipe line. Investigations in connection with the scientific control of reservoir were dealt with in considerable detail in last year's review. This work has been steadily pursued during 1933 and certain of the investigations have been the subject of papers presented to the World Petroleum Congress held in London in July of last year.

Jan 1, 1934

By Stephen Burke

THE oxidation of pyritic sulphur associated with coal is important for the following reasons: 1. It is the predominant cause for the formation of acid mine drainage issuing from bituminous coal seams. This drainage pollutes the streams in coal regions, making the water unfit for industrial purposes and causing the disappearance of fish and wild life. As a consequence the movement of industry and especially recreational industry, so important to the population of these areas as an alternative means of livelihood, is impeded. 2. It is instrumental in effecting a series of reactions, which bring about the degradation and ultimately result in the spontaneous combus-tion of bituminous coal in storage. 3. It contributes to the breaking and shattering of the coal structure and is one of the causes of roof falls and floor lifts in mines. 4. It is the primary cause of the many nuisances associated with gob piles and the refuse of cleaning plants. 5. Its proper control and application might possibly be employed in the preparation of coal to reduce the inorganic sulphur content. The research that has been conducted on the oxidation of the various forms of iron sulphides is extensive and the literature voluminous. Nevertheless, few efforts have been made to determine experimentally and with some precision the mechanism of the reaction under the condi-tions of its occurrence in bituminous coal mines. It has generally been accepted that the oxidation of pyritic sulphur proceeds according to the reaction 2FeS2 + 21120 + 702 --> 2FeSO4 + 2H2S04 [1] The ferrous sulphate in the drainage streams is further oxidized by air to produce ferric hydroxide and more acid. Yet the literature fails to dis-close any pertinent investigation on the mechanism of this reaction. The present contribution is concerned primarily with this aspect of the problem and while the work to be reported is not yet complete, it has yielded results from which interesting and significant conclusions may be drawn.

Jan 1, 1937

MILNOR ROBERTS,* Seattle, Wash. (written discussion?).-The coal fields of Washington, on which Mr. F. A. Hill's paper gives much detailed information, lie on the western slope of the Cascade Range, which extends north and south through the State just west of its center. The mines are on the lower half of the slope, the lignite fields of Lewis and Thurston Counties extending into valleys and low hills west of the mountains. An exception is to be noted in the case of the Roslyn field, a small but important area which lies on the eastern slope.

Jan 11, 1918

By G. W. Thomas

Jan 1, 1967

By T. Egleston

THE direct process for the manufacture of iron which is principally used in the United States, in New York and New Jersey, is called the Jersey forge, the Champlain forge, the Catalan forge, the Bloomary forge or fire, and sometimes a Forge fire. Dr. T. Sterry Hunt, who has discussed the process as applied to the beach sands of Canada as well as to ores, in the Report of the Canadian Geological Survey for 1867-69, has shown that the name of Catalan forge is incorrect, as this process in no way resembles the Catalan, but is really the old German bloomary modified by long use in this country. Dr. Hunt gives the probable history of the introduction of the process into the United States, and a series of historic citations of great interest relating to it. Not¬withstanding the improvements which have been made in the construction of the furnace and its greater output, the process to-day, in all its essential features, is carried out as Karsten described it. It should now be known as the American Bloomary. The name of Jersey or Champlain forge or fire is not sufficiently distinctive. The name of Bloomary, by which the process is usually distinguished, is objectionable, not because it is incorrect but because it is indefinite, as the Knobbling fires, which are a very slight modification of the Walloon process, for making blooms either from pig iron or by sinking scrap, are also called Bloomaries, and although Knobbling fires are only used in a few localities where charcoal pig is made, and special grades of charcoal-refined blooms are required, one does not, without an explanation, know whether the blooms are being manufactured from ore or pig. The name Forge fire is equally indefinite, as it might just as well apply to any of the five direct methods of making blooms which have been in use in Europe, but which have now mostly gone out of date. The Dame of American Bloomary, however, is the one which most completely describes it, and is the one least open to objection. The names of German, Jersey, and Champlain bloomary are too local, and these adjectives are thought unnecessary by those who use the process, and we shall not therefore describe it under any of these names, but as the American Bloomary process. * Read at the Montreal meeting, September, 1879.

Jan 1, 1880

By M. W. Strong

THE technique of handling drilling muds varies somewhat, partly because of personal factors but mainly because of differences in forma-tion, the type of problems met with, and the general drilling conditions in different localities. The much greater depths to which bore holes are now carried have made necessary closer attention to and great modifications of all aspects of drilling-mud technique. Increased depth means smaller hole, smaller drill pipe, smaller clearances, higher pumping pressures, higher differen-tial pressures between shows and the mud column, less accurate control of the weight of the mud column, delayed receipt of formation data, and poorer samples. It means longer delays and greater hazards in rectifying mistakes or dealing with accidental occurrences. Equipment on a larger scale is necessary and more pains must be taken with layout. Lastly, the budget costs of raw materials have risen to high figures and economy of time and of direct monetary expenditure have come to mean much more than formerly. A mud laboratory is now part of the essential establishment of a modern oil field and to it current problems can be submitted for the most thorough investigation. The detailed chemical properties of all mate-rials purchased or quarried have to be investigated. Detailed data on the physical properties have to be ascertained and research on improve-ment of material and its most efficient use has to be carried out. In this paper we propose to discuss the main mud problems with which we have to deal in Iran, some of which are peculiar to our local conditions while others are of the general type common to all workers in this subject.

Jan 1, 1938

By John W. Langley

The papers of Mr. W. J. Keep, read before this Institute, have called attention to the influence of aluminum in cast-iron and on iron and steel castings. The information in these papers is interesting and valuable, as showing the modifications which iron undergoes when dosed with sufficient aluminum to form a distinct alloy, the quantity of the alloying metal used being such that the amount remaining in the casting is sufficient to be readily discovered by analysis. The same is also true of the so-called aluminum-steel patented by R. A. Hadfield, where the proportions specified are such as to leave in the finished steel from one-twentieth to one-tenth of one per cent. of aluminum. Whether these alloys are of practical utility or not has thus far . not been proved by any extended tests on a large scale, and until such evidence is forthcoming it may be safely held, provisionally, that such a use of aluminum is of doubtful utility. But there is another function which this metal can perform that has been known for some time, and which has passed beyond the experimental stage, viz.: its beneficial effect in securing sound ingots. It appears to be a general property of all metals when in the fluid state and at a temperature considerably above their points of fusion, to contain gas, either dissolved from the air or frorn the furnace, or else self-evolved by internal reactions. Silver, perhaps, shows this power in the highest degree, and mercury and lead in the least; midway stands steel—the quantity of gas which it can hold in solution, or " occlusion " as it has been called, varies with its temperature, its composition, and its mode of manufacture. When the steel sets in the mould, a portion of this gas escapes, causing blow-holes, surface defects, boiling-over, wildness, and quite a long train of troubles, familiar to all practical steel-makers. Ferro-silicon has long been used as a quieting agent. The first extended use of it for this purpose was made at Terre-Noire, in

Jan 1, 1892

By Norman Pilling

The micrographic analysis of silicon steels is possible if a dilute solution of nitric acid and methyl alcohol in nitrobenzol is used. The action of this reagent differs from that of sodium picrate in that there is no persistent deep-seated staining and the solution is used cold. THE technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105° C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys.

Jan 1, 1924

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

By W. I. Garms, J. L. Stevens

Because of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following résumé of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. Mills Used Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was 13½ in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 162/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. Initial Test During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local 'grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1947

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953