Search Documents

By William P. Blake

In southern Arizona and in Mexico the word caliche is in general use to denote a calcareous formation of considerable thickness and volume found a few inches, or a few feet, beneath the surface-soil, upon the broad, dry, gravelly plains and mesas. , In western South America the same name is applied to the beds of crude soda-niter (Chili saltpeter). While these deposits of South America and of Arizona are totally different in composition, and have nothing in common, except that both occur in

Jan 1, 1902

By G. H. Kesler, J. E. Oberele, C. E. Dryden, J. H. Oxley

Heat-transfer rates were measured in a model of a multifilament vapor-deposition bulb fo the preparation of high-purzty metals. Local transfer coefficients for heat transfer frow the filaments to the circuates process stream were determined as a functiol of gas flow rates and bulb, inlet, and filament, geowzetvies. These results a-e then convertted to n mass-t7,ansfer basis to provide a method of correlating vapor-deposition rates and to predict the performance of commercial urzits. The firm1 cor?,elating equation for mass transfer was found to be- wheve k, is the mass-transfer coefficient; D, is bze gas difficsivity : P is the system pressure; R is the gas constant; T is the gas temperature; Df, DB, and Di ave tlze diameters of the filament, bulb, and inlet, respectively; k is the gas conductivity; C, is the specific heat of the gas, M is the wzolecular zleight of the gas; Npr . N,,, NRe a7'e the Prandtl, Schmidt, and Reynolds numbem of the system, respectively; LB is the height of the bulb; and SB and Sf are the total suyiace area of the bulb and filaments, respectively. ONE of the more conventional methods of preparing very high-purity metals is the vapor deposition of the metal upon heated filaments. The reactions which can be employed in such a process generally fall into two classes: 1) Pyrolysis of a volatile metal compound. Generally because of their instabilities, metal iodides are used; however, other metal halides and hydrides have been employed. These processes are frequently carried out under vacuum conditions, and the filaments are maintained at high temperatures. 2) Hydrogen reduction of a volatile metal compound. A metal chloride is normally the preferred feed for these processes, but other halides are sometimes used under special conditions. These hydro- gen-reduction processes are usually operated at atmospheric pressure. Many of the current processes for the production of semiconductor materials are actually vapor-deposition processes. However, the vapor-deposition process itself is relatively old, and almost all metals can be prepared in a state of very high purity by the use of vapor-deposition techniques. Loonam has recently given an excellent review of the iodide process for metal deposition,' and Owen has started some detailed studies with a carbonyl system.' A more general treatment of all vapor-deposition processes has been outlined by Powell, Campbell, and Gonser.3 Despite the fact that vapor-deposition techniques have been employed since 1890, there is a surprising lack of fundamental information regarding the transport characteristics of even the simplest deposition system, the heated filament. The purpose of the investigation described in this paper was to extend some of the earlier data obtained at Battelle to predict deposition rates and the uniformity of deposition in large-diameter, multifilament deposition bulbs under forced convection conditions.4'5 A number of other investigators have already presented a simplified treatment of the deposition process under non-flow conditions, i.e., pure diffusion.6"9 To obtain information on the transport characteristics of a deposition bulb, a model of a typical plant deposition unit was constructed, and local heat-transfer coefficients from the filaments to a circulating air stream were determined under various conditions of air-flow rates and bulb, inlet, and filament geometries. These results were then converted to a mass-transfer basis, and consequently provided a method to correlate experimental vapor-deposition rates and to design commercial deposition units. EXPERIMENTAL WORK Description of Model. The apparatus which was used in this work was a scaled model of one type of deposition bulb. It was constructed of Lucite and was easily altered to give several combinations of diameter of bulb liner, inlet size and location, number of filaments, and outlet geometry. The model is shown in Figs. 1 and 2. The bulb shell was made octagonal for convenience in construction and observation, and the bulb liners were cylindrical. Air, introduced through one of several different jet inlets, was used as the test fluid in these model studies. Filaments for deposition of metal were simulated by metal rods 1/4-in. in diam. Two of the rods could be heated by passing electrical current through them ¦ while the remaining rods could not be heated. This procedure minimized the amount of heat which was

Jan 1, 1962

[ ]

Jan 1, 1938

By Norman B. Pilling

The technical difficulties hampering the metallographic analysis of silicon steels are chiefly the result of the extreme corrodibility of these alloys. The addition of silicon to iron in increasing quantities, up to about 6 per cent., rapidly increases the susceptibility of the alloy to chemical attack, not only in acid solution, but in water. This renders the preparation of metallographic sections very difficult, because of a non-selective attack upon the finely polished surface by the water used as a lubricant in polishing. This water attack masks the true structural details revealed by suitable etching reagents. It is thus necessary to use alcohol as a polishing lubricant in the last stages of preparation and to avoid all etching reagents having an aqueous base. A specific reagent for the identification of iron carbide in ferrous alloys, and the one hitherto used almost' exclusively by metallurgists, is an alkaline aqueous solution of sodium picrate, which stains this constituent selectively. Its application to silicon steels has not proved successful, as its distinctive selective action is more or less completely hidden by the general attack of the aqueous solvent on the silico-ferrite, greatly accentuated by the fact that this reagent must be used at its boiling temperature (105' C.). Thus, a powerful metallographic aid to the study of the higher silicon alloys, such as transformer steels, is lost. A new reagent has been developed for the purpose of overcoming this difficulty. It is with some hesitation that the list of etching reagents, already overburdened, is increased, but the properties of this new reagent are advantageous in several ways and a definite field for it may be found in the metallography of ferrous alloys. The reagent consists of a dilute solution of nitric acid and methyl alcohol in nitrobenzol. It is a great advantage to secure an anhydrous solution, as a tendency toward acidic etching has been traced to small amounts of water. A convenient method of preparation is to make an anhydrous stock solution of nitric acid in methyl alcohol in the proportion 20 per cent. acid by weight (12.5 per cent. by volume). The alcohol can

Jan 1, 1924

During the latter part of the Civil War an income tax was placed upon coal and the production of coal in the various collection districts during the life of this tax is shown in the tabulation that follows. The counties that include coal deposits are shown for each district. No record exists now of the production by counties, but it is calculated here on the basis of tax collected. The table, of course, does not include any territory not under the control of the northern armies, and not all of that in some cases.

Jan 1, 1942

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

By A. Eilers

The year 1874 marks a decided advance in the metallurgy of the West, in two directions. On the one hand, the technical management has been very materially improved, and on the other, the production has been largely increased over that of the previous year. The technical improvements of greatest importance are the introduction of condensation-chambers, or flues, at several works, and the further treatment of the lead matte produced in the ore smelting. These two are of general importance, and although by no means introduced at the majority of works, their adoption at the few where their great importance has begun to be understood will no doubt bring about their universal introduction. To these may be added a third step forward, which for some localities is vital enough, though for others it must still remain doubtful whether it is to be regarded as an improvement or not. This is the introduction, at several

By Benjamin LeRoy Miller, Joseph T. Singewald

The ore deposits at Firmeza have been worked continuously since 1884; those at Daiquiri since 1895. It is surprising, therefore, that they have not been the object of careful geologic study until quite recently. It is true that considerable attention was paid to these deposits by A. C. Spencer, in 1901, in the report on the geology of Cuba, by Hayes, Vaughan, and Spencer,l but this was only incidental to a hasty general reconnaissance of the Island. As far as the Daiquiri deposits are concerned, this gap has been filled by the appearance of the two papers by Prof. James F. Kemp2 and by Prof. Waldemar Lind-gren and Clyde P. Ross respectively.3 Max Roesler, first holder of the Emmons fellowship, made a detailed study of the Firmeza deposits during the past summer, so that soon we can expect a full description of them. Consequently, there is no, demand at the present time for a description of the deposits from other sources, and that is not the purpose of this paper. The papers on Daiquiri, however, leave unsolved problems in regard to the age of the rocks of the district and certain phases of the genesis of the deposits, and it is with the hope of aiding in the solution of some of these problems that this contribution is offered. Kemp, and Lindgren and Ross agree in assigning these deposits to the type of contact metamorphic deposits. They disagree in part on the question of their localization. The deposits occur in an extensive area of diorite which includes numerous blocks of limestone, and sometimes are found in the contact zones between these blocks and the diorite, and in other instances are completely enveloped in the diorite, showing no apparent connection with the limestone. The latter class includes

Jan 1, 1916

By H. J. Wasson

DEVELOPMENTS in Venezuela during the past few months have been obscured by the hap-penings in Seminole and, more recently, those in southwest Texas. The question has been asked whether or not the opening of these vast new, prolific areas in the United States may not have depressed prices to a point so low as to give the developments in the Caribbean countries a serious setback. Nothing of the kind, however, has taken place, and on the contrary, there has been demonstrated the fact that Venezuela can profitably produce great quantities of oil under existing market conditions, and at the same time finance the foundation for further large expan-sion in the future. The three big factors which contribute to place Venezuela in a unique position and tend to insure the steady expansion of its oil industry are, in the order of their importance: I. Reasonable oil laws backed by a sound govern-ment, which comprehends the all-important fact that the country's prosperity depends on the prosperity of its industries, in a word, perceiving that the goose which lays the golden egg merits considerate treatment. II. The low cost of placing Venezuela oil on our At-lantic seaboard; not over $0.60 per barrel. III. The uniformly high average production per well and the large area of some of the individual pools. Under these conditions Venezuelan producers may be expected to continue steady and profitable ex-pansion even in the face of further market slumps. Their position is analogous to that of the low-cost copper producers, and unless artificial barriers, such as tariffs, come into play, Venezuela will steadily grow in importance. Within less than five years it should be second only to the United States among the oil-producing countries of the world.

Jan 10, 1927

A mine in the mountains of southeastern British Columbia is fast earning a reputation as the safest metal mining operation of all time. Already officially proclaimed as the safest mine in Canada, the H.B. mine of The Consolidated Mining and Smelting Co. of Canada (Cominco) continues to advance its safety performance far in the lead of average accident frequencies in mines across the country. Official recognition came its way again this spring when the Cominco mine was awarded the John T. Ryan trophy for the fourth time in the last five years. This award is emblematic of top national safety performance of a metal mining operation. The H.B. mine is its only four-time winner. The Ryan award is based on a frequency of accidents involving lost time of more than six days. In each of the years that the H.B. has won the award-1958, 1959, 1961 and 1962-its frequency was zero, with no accidents involving a time loss of more. than six days

Jan 12, 1963

By D. L. Creighton, S. A. Hoenig

The field-emission microscope has been adapted for the study of microcrack growth during the early stages of fracture in metal wires. Cracks as small as 6 1 in length can be detected and their growth can be followed to specimen failure. The system is quite useful in searching for microcracks since only sharp-edged surface defects will emit electrons under the experimental conditions. THE conditions leading to brittle fracture were discussed a number of years ago by Griffith1 and the term Griffith Cracks is often used for the small surface cracks which are responsible for brittle fracture. Griffith's theory has been modified by stroh2 and more recent results on metals are discussed by Allen,3 pp. 123-40. At present the phenomenon is not completely understood but there is general agreement that at least in certain materials the sequence leading to brittle fracture involves several stages. The initial microcracks are present because of cooling or working stresses, Hahn et al.,3 p. 95. When a stress is applied to the specimen the cracks grow slowly until the release of stored elastic energy is large enough to accelerate the crack and provide the necessary surface energy for crack growth. At this point the growth rate appears to increase rapidly to some new equilibrium velocity, and failure occurs. Since the microcracks are usually about the size of a single metallic grain (Ref. 3, p. 99) it is not easy to find them and it is very difficult to follow their growth under stress. This paper will report on the use of a cylindrical field-emission microscope for observation of the formation and growth of microcracks. I) THE FIELD-EMISSION MICROSCOPE The field-emission microscope (FEM) has a high magnification and resolution and is almost uniquely suited for observations of microcracks. Since the FEM is relatively new as a metallurgical instrument, a short description will be given here. Normally metals at room temperature do not emit electrons; however in the presence of a strong electric-field gradient, electrons can tunnel out through the reduced potential barrier. Since this tunneling is a function of the local field gradient and the local work function, the emitted electrons can be used to produce a highly magnified image of the surface by allowing them to strike a phosphor screen. Because the electron emission is dependent upon the local field gradient, smooth surfaces emit few electrons except at very high fields. On the other hand cracks, extrusions, or other surface defects, having sharp edges, emit strongly since the field gradient is very high in the vicinity of these defects. This indicates that the FEM should be most useful for detection of microcracks on otherwise smooth surfaces. A field-emission microscope was first used by Muller4 in 1936 for observation of metal surfaces, and recent reviews have been given by Muller5 and Gomer.6 The instrument has been used for metallurgical studies in the area of surface diffusion,= recrystallization,7 and grain growth 8 (Ref. 8 is directed specifically at metallurgists). In the work of Muller4,5 and Gomer 6 the specimen was in the form of a sharp metal point at the center of a phosphor-coated glais sphere. The impact of the emitted electrons on the phosphor produced a highly magnified image of the specimens. Such a system is not practical for applying a controlled stress to the specimen and a cylindrical geometry has been used in this investigation. This allowed the application of a controlled tensile stress to the wire specimen. Normally a cylindrical FEM geometry produces magnification only in the radial direction. This is the case because a smooth wire at the center of a cylinder produces a purely radial electrical field. However, if there is a break in the smooth surface of the inner cylinder, the field near the break becomes three-dimensional and the area of the break is highly magnified. The reason for this is clear if it is recalled that the field gradient depends on the relative radii of the inner and outer cylinders; if a crack forms, its edge radii are of atomic dimensions and a very high field gradient is formed near these crack edges. Since the electrons receive most of their acceleration near the crack edge and are always traveling perpendicular to the field lines, they tend to spread out and produce the magnified image observed in the cylindrical field-emission microscope. 11) BRITTLE-FRACTURE STUDIES A) Experimental Apparatus. The geometrical arrangement chosen was that used earlier by Gifford

Jan 1, 1965

By A. B. Tanner

The effects of radon in drillholes on gamma-ray logs have been described by L. S. Hilpert and C. M. Bunker1 Since these effects may cause drastic error in the evaluation of uranium deposits, it is useful to know the conditions under which significant amounts of radon tend to accumulate in drillholes. In the studies described here, atmospheric conditions were found to dominate in the control of the behavior of radon in drillholes in the vicinity of a uranium orebody. The site of the investigation was in McKinley County, New Mexico, about 12 miles north of Grants. Drillholes of 4 1/4-in. diam, on 25-ft and 100-ft centers, penetrate ore in dry rock at a depth of about 100 ft. A geologic log of the drillhole of primary interest is shown in Fig. 1. Gamma-ray logs revealed three zones of ore-grade mineralization in the Todilto limestone. A 6-ft zone, the lowest of the three, assayed 0.20 pct U3O8 by chemical analysis. The limestone ores in this area contain disseminated uraninite and some yellow and orange secondary minerals. Only radon"", a member of the uranium'" series, was measured in this investigation. Radon is one of the chemically inert noble gases and is radioactive by alpha particle emission with a half life of about four days. In this discussion, amounts of radon are expressed in microcuries (1 microcurie equals 37,-000 disintegrations per sec) and concentrations of radon are expressed in microcuries per liter of drillhole air. Samples of air were obtained by lowering a sampling device (Fig. 2) into a drillhole and actuating the device at the desired depth. It was then raised to the surface and the sample was transferred to a storage tube. Within two days the sample was transferred to an ionization chamber, and the activ- ity of radon and its short-lived daughter products was measured at radioactive equilibrium with a vibrating-reed electrometer. The measurements were corrected back to the time of collection and involve errors estimated generally not to exceed + 5 pct to —15 pct. Radon Behavior in a Covered Hole: Fig. 3, a typical log of radon concentration vs depth in the covered drillhole, was made by using values of radon concentration at discrete depths. Continuous logs of alpha-particle radiation in the drillholes showed that such radon logs depict the continuous variation of radon concentration with depth quite accurately. Three features of radon logs were noted: 1) maximum

Jan 1, 1960

By W. C. Winegard, W. J. Bratina

Internal friction characteristics and temperature dependence of the torsion modulus for iodide zirconium containing 2.4 pct Hf were investigated, using a low frequency pendulum technique. The internal friction curve consists of a background which increases as the temperature increases, a maximum at 860°C apparently a background due to the al-lotropic transformation, a maximum due to grain boundary relaxation with an associated heat of activation of 58,000 cal per mol, and an anomaly below 350°C which may be associated with a precipitation perphenomenon, Oxygen in below small amounts reduces the grain boundary maximum substantially. The variation of the torsion modulus at 20°C was found to be 3450 Kg per mm2 for the zirconium used in the present work. IT is well known that small amounts of certain solutes materially affect the ductility of zirconium. Lely and Hamburger,&apos; as early as 1914, found that high purity zirconium exhibited a remarkable ductility, while Fast&apos; has shown that oxygen and nitrogen can cause substantia1 embrittlement. Treco" has recently demonstrated that the ductility decreases sharply with the oxygen content, and that 2 atomic pct O2 embrittles zirconium to such an extent that cold working is impossible. The marked decrease in ductility is difficult to understand in view of the fact that Domagala and McPherson4 report the solid solubility of oxygen in zirconium to be 29 atomic pct at 500 °C. Another metal which behaves much the same as zirconium in this respect is titanium. Pratt et al." investigated the internal friction characteristics of titanium and the effect of oxygen on the internal friction values. It is evident that internal friction measurements are of value for studying grain boundary segregation, as shown by Pratt et al. for oxygen in titanium, by Pearson for oxygen in copper, and by Maringer and Schwope for oxygen in molybdenum. With this in view, the internal friction characteristics of zirconium and the qualitative effect of oxygen on the grain boundary relaxation phenomenon were investigated. Materials and Experimental Procedure The zirconium used in the present work was supplied by the Foote Mineral Co. in the form of wire 0.05 in. diam. The analysis supplied by the manufacturer indicates the amount of hafnium as 2.4 pct, less than 0.01 pct O less than 0.01 pct N,, less than 0.02 pct H,, and less than 0.001 pct C. Additional spectro-graphic analysis indicates the other main impurities as follows: 0.01 pct Fe, 0.05 pct Si, 0.008 pct Cu, <0.005 pct W, <0.001 pct Al, <0.05 pct Mg, <0.001 pct Ni, <0.02 pct Ca, and <0.01 pct Ti. Microscopic examination of the material in the as received condition revealed very fine grains with numerous twins. Specimens were annealed either in situ in the internal friction apparatus or in evacuated silica tubes in an auxiliary furnace. When the specimens were annealed in the auxiliary furnace, they were wrapped in identical zirconium wire to prevent contamination by the container. Metallographic sections were taken in all cases. Some were taken from the specimens used for internal friction measurements after completion of the experiments, while others were taken from control specimens at intermediate stages of the experiments. lnternal friction values were obtained by measuring the free decay of a low frequency torsion pendulum (1 cycle per sec), the suspension of which was

Jan 1, 1957

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By J. Fageant, W. C. Ellis

All major regions in a progressively solidified germanium ingot were related through successive orders of octahedral twinning. The occurrence of lineage structure and the generation and survival of orientations are discussed. WHEN metals solidify in a temperature gradient a preferred orientation, or casting texture, usually develops. For example, in face-centered and body-centered cubic metals, most of the solidifying crystals have a cube axis, <loo>, aligned approximately in the freezing direction.&apos; In the solidification of diamond cubic metals this is not the case, since there is a natural tendency to form twin orientations.&apos; . In this paper, twinning relationships in cast germanium are described; some conclusions with respect to nucleation and survival of new orientations are discussed. In the first experiment, an ingot of high purity germanium, % in. in diameter and 1 % in. in length, was formed by progressive solidification4 from the bottom. The ingot was cut into 21 slices, each circular and about 0.030 in. thick. The top surface of each slice was polished and etched to reveal the regions of different orientations. Orientations were determined by the Laue X-ray back-reflection method. The uncertainty in the determined orientation relationships was l" or 2" when separate slices and films were involved. Frequently, however, advantage was taken of illuminating across a boundary when the patterns of the two orientations were recorded on the same film. The uncertainty then was less than 1". Often the twin relation was evident from common zones or individual reflections. Twin relationships were recognized through comparison of the values of the nine angles between cube poles of the two orientations with those calculated for successive orders of octahedral twinning. The birth and survival of each region can be reconstructed by visual examination of the etched slices shown in Fig. 1. In slice 21, where solidification began, many regions are present; these regions were found to be twin-related. Solidification appears to have started from one nucleus formed probably at the wall of the crucible.* Subsequent ori- entations were developed by nucleation on existing solid surfaces, and only in the twin relationship. This is an example of a general process of nucleation on a surface of existing solid and may be descriptively termed oriented nuc1eation.t In germanium, and other diamond cubic substances, the orienting habit is that of twinning on an octahedral plane.&apos; " The prevalence of straight traces in the polished surfaces of succeeding slices (Fig. 1) suggests that the twinning observed in the first slice persisted throughout solidification. This was confirmed by X-ray determinations. The schematic diagram of Fig. 2 shows the twinning relationships of the major regions throughout the ingot. Since all observed relationships are describable as twinning, it is reasonable to conclude that no random nucleation occurred in the freezing of the ingot. An alternative possibility would be that nucleation of a random nature occurred, but only those nuclei in twin orientations survived in subsequent growth. This is unlikely for there would be as good a reason for the growth of randomly oriented nuclei as for the growth of the many different orientations present after several orders of twinning. The many twin components contain a wide distribution of orientations, and did grow. In fact, they are the only ones found in the solid. The conditions of solidification of this ingot were such as to discourage nucleation of crystals wholly in the liquid. The rate of solidification was 0.125 in. per min. This slow rate of heat removal afforded but small opportunity for supercooling within the liquid —a condition needed to provide enough decrease in free energy for such nucleation. When nucleation occurs on an existing solid surface, the interfacial energy between the existing and forming regions is important in determining the new stable orientation. The new orientation is expected to be one which minimizes this energy. In the diamond cubic structure, the interface for the

Jan 1, 1955

By D. R. Colton, W. V. Youdelis

The maximum segregation, as a function of alloy composition, is calculated for the aluminum-zinc system using the theory of inverse segregation based on the mechanism of volume contraction and interdendritic flow. The results show good agreement with experiments on aluminum-zinc ingots. The significance of the mass calculations of the segregation theory in discussing the metallography of the cast aluminum-zinc alloys is considered. THE occurrence of inverse segregation in rapidly cooled castings has been reported on previously by various authors, and several theories have been proposed to explain this phenomenon. It is now generally accepted that the mechanism of inverse segregation involves volume contraction on solidification followed by interdendritic flow of enriched residual liquid to the contraction volumes. This increases the concentration of the lower-melting-point constituents in regions of first solidification to above the mean concentration, which is con-

Jan 1, 1961

By George Smith

THE Secretary of the Interior in his recent report to the President has defined the new public-land policy, which is in fact "but a new application of an old policy." His words may be more acceptable on this subject of land classification than the repetition of phrases which have served some of us for several years. Secretary Lane says of the past: "Congress has always been most generous as to the disposition of the national lands. . . . There was land for all, and it was the government&apos;s glad function to distribute it and let those profit who could. . . . And this generous donor was not so petty as to discriminate between kinds of lands, the uses to which they could be put, or the purposes which those might have who got them. Land is land, save when it contains minerals; this was roughly the broad principle adopted. To classify was a task too difficult or not worth while. The lands would classify themselves when they arrived in individual ownership. And so the door was opened for monopoly and for fraud. Of the reaction and the evolution of a new policy, the Secretary continues: "A reaction was inevitable. If lands were to be withdrawn from public service, why might not the government do the withdrawing itself? The old philosophy that `land is land&apos; was evidently unfitted to a country where land is sometimes timber and sometimes coal; indeed, where land may mean water-water for tens of thousands of needy neighboring acres. For the lands of the West differ as men do, in character and condition and degree of usefulness. We had not recognized this fact when we said `land is land.&apos; Lands fitted for dry farming and lands that must forever lie unused without irrigation; lands that are worthless save for their timber; lands that are rich in grasses and lands that. are poor in grasses; lands underlain with the non-precious minerals essential to industry or agriculture; lands that are invaluable for reservoir or dam sites these varieties may be multiplied, and each new variety emphasizes the fact that each kind of land has its own future and affords its own opportunity for contributing to the nation&apos;s wealth.

Jan 6, 1914

By S. A. Hovanessian

Analytical solutions are obtained for calculating the pressure distribution in rectangular fields due to injection and/or producing wells located anywhere within the field. The field is assumed to be homogeneous with either constant pressure or no-flow boundaries. These solutions are extended to include the calculation of average reservoir pressure and permeability from pressure build-up curves. Numerical examples are given to illustrate the application of equations to practical problems. INTRODUCTION Pressure distribution analyses are of considerable importance in the field of reservoir mechanics. A number of papers dealing with this subject have appeared in the petroleum literature. perrinel in 1956 presented a summary of the methods available for pressure build-up calculations and discussed the applicability of each in some detail. More recently (1958), Hazebroek, et a1,2 discussed a theoretical method for obtaining pressure distribution in a radial field. Also in 1958, Nisle3 gave a theoretical solution of the pressure distribution in a field extending to infinity with a partially penetrating line source at the origin. Mathews, et a1,4 applied the method of images to existing solutions for pressure distribution in radial fields and obtained expressions for calculating pressures in bounded reservoirs. However, a literature survey revealed that a general analytical solution for the pressure distribution in a rectangular field, with injection and/or production wells located anywhere within the field, was not available. Such a solution could be used to approximate the pressure distribution in a field the shape of which is nearly rectangular. Furthermore, it could be applied to pressure calculations pertaining to a single well taken from a system of wells which were drilled in a rectangular pattern. In this case the boundaries of the well drainage area are considered to be the perpendicular bisectors of the lines joining the well and its nearest neighbors. The basic problem considered in this paper consists of a rectangular field with either constant-pressure 01 no-flow boundaries and with either an injection or production well located anywhere within the field. The physical properties of the rock and fluids present are considered to be constant. Analytical expressions are obtained for the pressure distribution within the field during the production or injection periods. These expressions, which are infinite series, can be used to evaluate pressure at any point within the field as a function of time and position. For fields containing more than one well (production and/or injection), the solutions for each well acting independently are superposed. That is, at any point in the field, the pressures due to each injection 01. production well acting alone can be algebraically added to give the pressure resulting from all wells acting simultaneously. Evaluation of the series solutions given in this paper is readily accomplished by means of an electronic digital computer; and, in most cases, sufficient accuracy is obtained by setting the upper limits of summation at 20. These solutions are extended to include the calculation of average reservoir pressure and permeability from build-up data. A number of numerical examples are given to illustrate application of the solutions to actual field problems. ANALYTICAL SOLUTIONS The partial differential equation representing the pressure distribution in a homogeneous rectangular field (see Fig. I.), having a single source or sink of strength (2, can be written*

By E. B. Burwell, R. H. Nesbitt

Designed by army engineers, the NX borehole camera provides the most economical method of subsurface exploration so far devised. Continuous cylindrical color photographs now reveal minor flaws in foundation bedrock not always disclosed by borehole samples. A unique projector transforms the photographs into true-to-scale images of three dimensions. ANEW milestone in the progress of photography and subsurface exploration was reached when the Chief of Army Engineers announced the development of the NX borehole camera. In obtaining continuous undistorted cylindrical color pictures of dry or water-filled borings the device surpasses all other cameras designed for photographing interior surfaces of pipes, wells, and conduits. The usefulness of the camera and the unique projector that comes with it are at once apparent. To the geological, mining, and civil engineer alike it signifies the end of guesswork with respect to underground conditions that have eluded identification by conventional core-drilling methods. To the medical profession it may well signal new progress in photo optics which could result in cylindrical color photographs supplementing the X-ray and existing photographic methods used in exploratory surgery. The pilot model of the camera has more than paid for itself as a result of its success in bringing to the surface at two dams information previously obtainable only by costly drilling of mansized boreholes for subsurface on-the-spot examination. Such bores cost as much as $200 per lineal foot as against $10 per ft for the conventional 3-in. or NX exploratory core borings from which the present invention derives its name. The NX camera can now photograph completely the interior surface of these borings. Research and development for the first camera and projection equipment were conducted by Engineering Research Associates, Division of Remington Rand, Inc., under the technical supervision of the Geology and Geophysics Branch, Office of the Chief of Army Engineers in Washington, in accordance with plans and specifications furnished by this branch. Subsequent modifications of the camera-lowering device, transporting equipment, and special field tools were made in the Corps of Engineers&apos; Ohio River Division Laboratories in Cincinnati. The background of this development is interesting. Among the more difficult foundation problems involved in construction of concrete dams are those resulting from bedrock imperfections that escape disclosure by conventional exploration methods. Often these imperfections are of sufficient magnitude to introduce costly changes, especially when their presence is discovered only after foundation excavation is well in progress. Bedrock flaws most frequently camouflaged may be ruptures resulting from the enormous stresses to which rocks have been subjected, or they may be planes or zones of weakness related to chemical alteration and underground erosion. Obviously, detailed information on their location, dimensions, and structure is important, as these factors can affect the stability of a dam and the security of life and property downstream. Their discovery and appraisal entail extensive subsurface exploration. At present the most economical exploratory tool available to geologists and engineers is the small-diameter diamond core drill by means of which cores of the foundation bedrock are recovered for examination and testing. All too often, however, these samples fail to disclose minor foundation flaws that may be of major importance before a structure is completed. As a result, the small-diameter drillings are supplemented generally by more reliable but much more costly shafts, tunnels, or large-diameter calyx drill holes that permit the investigator to examine the foundation rocks in place. It was to reduce the number and cost of these expensive and time-consuming investigations, as well as to obtain more complete information on rock structure from the smaller borings, that the NX borehole camera was developed. That it has been eminently satisfactory in accomplishing that purpose is demonstrated by its success most recently at the Folsom dam, under construction on the American River, 23

Jan 1, 1955