Search Documents

By Walter McDermott

This machine is an improvement on the well-known endless travelling belt used for dressing slimes in many mills; the chief point of difference, and constituting the essential advantage of the present over the old form, is the application to the machine of a secondary agitating or shaking motion, in addition to the ordinary progressive motion of- the belt. In the machine as heretofore made, the inclined belt or apron moved slowly up against a thin stream of water and ore, depositing the concentrations carried over in a tank placed below, through which the belt travelled, of course, in a reversed position. By reference to the accompanying drawings, it will be seen that in this main principle the new modification does not differ materially; but the means by which it is carried out are essentially different. The machine consists of a substantial frame of mood, F, Figs. 41, 42, and 43, within which hang the shaking frame and rollers, B B, A, Endless apron ; B, Apron frame and rollers ; C, Driving drum ; D, pulleys; B, Shaft and connecting rods; F, Wooden frame; G, Shaft of regulating Pulley; H, Yokes. supporting the upper half of the travelling apron, A, which passes below around the driving drum, C, in the water-tank, J. On leaving the water-tank, the belt passes over the guiding and tightener pulley, G. The ends of the shaking-frame, B, are provided with iron yokes, H H, bored to admit the shafts of the end rollers, and carrying a lug, by which attachment is made to the connecting rods,

By I. R. Kramer, L. J. Demer

T. H. Alden and R. L. Fleischer (General Electric Research Laboratory)— The authors' results indicate clearly and, we believe, significantly that during tensile deformation the surface layers of an aluminum crystal are hardened more severely than the interior of the crystal. A probable explanation of this effect, as the authors indicate, is that dislocations in the primary slip system may be obstructed at the surface or, it should be added, near the surface. The intent of this discussion is to show that the oxide film on aluminum is not likely to be responsible for this effect, but that the results can be understood if it is assumed the secondary slip is more active in the surface layers than in the interior. Prior study has shown that the principal mechanical effect of an oxide film on a single crystal is to raise the yield stress while leaving the rate of strain hardening during the initial deformation relatively unaffected.33 Since the yield stress is unchanged during polishing in the present case, we conclude that continual removal of the oxide film exerts a small effect on the plastic hardening.* It appears that the hardening interactions are occurring not only at the immediate surface, but to an appreciable depth below it, although with decreasing severity. For example, Kramer and Demer found that with removal of 0.004 in. from a specimen, the easy glide region was extended somewhat; but the yield stress did not decrease. The initial yield stress was recovered only after 0.041 in. was removed. Since a very brief polish would permit dislocations trapped behind a surface film to run out,34 extra dislocations must, instead, be trapped to a considerable depth below the surface. The same conclusion is drawn from the observation of decreasing hardening slope with increasing surface removal rates. If the hardening interactions were only at the immediate surface, a full softening effect would be observed at some small removal rate. The view is taken here that strain hardening is principally caused by small amounts of secondary slip.35 The secondary dislocations will interact in various ways with the primaries, interfering with their motion and causing them to accumulate in the crystal. Prior studies of easy glide have shown Diehl's model of hardening to be qualitatively consistent with the effects of impurities,36 of temperature,36 and of crystal size.37 On this basis the enhanced hardening of the surface layers in aluminum arises from increased secondary slip at and to some depth below the surface. Selective removal of this hardened layer is expected to decrease the measurable "bulk" hardening, the effect increasing with the removal rate and decreasing with the applied strain rate. We suggest that the stress on secondary systems is raised by the bending moments arising from interactions with the grips during the deformation. This stress from the grips has been shown to be a maximum37 near the surface, and hence, increased secondary slip should result. Prior investigations of grip effect:; indicate that as the grip stresses are raised by changing the crystal shape, the easy glide slope increases while the extent of easy glide decreases.38-40 It has been shown also that bending moments superimposed during tensile testing may either decrease easy glide, when supporting the moments caused by gripping, or increase it, when cancelling the gripping moments.38 This interpretation of the authors' results, emphasizing the special importance of secondary slip near the surface, is also consistent with the earlier results of Rosi.41 Copper crystals alloyed with silver in the surface layer show greatly increased easy glide compared with pure copper. In addition, the easy glide slope is reduced. The effect of bulk alloying in extending easy glide has been well established and has been interpreted as indicating the relative difficulty of secondary slip in alloy crystals. Since non-basal glide is difficult in zinc crystals, the effects of surface removal during deformation may be less important. Experiments to test this idea are in progress. I. R. Kramer and L. J. Demer (authors' reply)—The authors wish to thank Dr. Alden and Dr. Fleischer for their discussion. Our interpretation of the data in the paper is that dislocation motion is obstructed by "debris" which starts to form at the surface and extends towards the interior of the crystal with further plastic deformation. The fact that we did not find a reversion from Stage II to Stage I by surface removal shows that in Stage II the "debris" fills the entire cross-section of the specimen. Drs. Alden and Fleischer take the view that bending stresses due to the grips are responsible for the

Jan 1, 1962

By Laurance Reid

HIGH compression ratios, resulting from high injection pressures and relatively low recovery process pressures, constitute a major problem, which has confronted those engaged in gas recycling for condensate production since the beginning of that practice. Despite the numerous process developments and improvements, no entirely satisfactory solution for this prob-lem has been presented to date. Often, where the residue gas from the recovery process must be recompressed for subsurface injection, there is a substantial difference between the required injection pressure and the plant-operating pressure required to produce maximum recovery of condensate. These limitations result in high compression ratios, which, in turn, neces-sitate excessive compressor investment and operating cost. As an alternative, the operating pressure may be increased in order to lessen the compressor requirements but such a saving often is purchased at the expense of decreased condensate recovery, caused by operation at the higher pressure. Regardless of the choice, the net result is a diminished return on the capital invested in the project. The goal of future development in this field must be the complete recovery of all valuable hydrocarbon components in the reservoir fluid at pressures that, regarded as compressor suction pressure, will require minimum compressor horsepower to inject the residue gas into the formation. A com-pression ratio of 1.5 has been established as an optimum for modern compressor equipment." Therefore, in order to con-form to this optimum condition, a 3000-lb. injection pressure would require that the condensate recovery process be operated at 2000 lb. per sq. inch.

Jan 1, 1940

By Charles E. W. Bateson

The Mojave mining district is situated in a group of small hills centering around Soledad peak, in the Mojave desert, Kern county, Cal. These hills are about 4.5 miles SSW. of Mojave, a railroad town at the junction of the Santa Fé and Southern Pacific railroads. The town of Mojave is about 50 miles north of Los Angeles, to which it is connected both by telegraph and by rail. The distance on the Southern Pacific railroad is 102 miles, covered in 3 hr. and 45 min. by express train. A sketch-map of this region is shown in Fig. 1. The Mojave district is relatively isolated. The only other mining towns in this section of California are Randsburg and Johannesburg, in a district (containing the well-known Yellow Aster mine) at the northern end of a low range of hills, which begins about 20 miles NE. of Mojave, runs nearly N. for 35 miles, and varies in width between 3 and 6 miles. As will be seen later, the origin and formation of these hills are not the same as those of Soledad peak. II. Climate and VEgetation. The climate and vegetation of the Mojave district are typical of the arid regions of the southwestern United States. During the winter and spring there is some rainfall, and the tempera ture is generally from 60" to 70" F. in the day-time. The rainfall in the spring is often very considerable for short spaces of time, and cloud-bursts are not infrequent. In summer there is continual sunshine, with temperatures, as a rule, exceeding 100" F. in the day-time, while 115" F. in the shade of a house is not at all unusual; but at night the temperature falls considerably. No rain falls during the summer. The vegetation

Jan 1, 1907

Uranium, the object of a quarter billion-dollar search in the US during 1977, is a ubiquitous element rarely found in economic concentrations. It originates in magmas as a large tetravalent ion, the size of which restricts it from the crystal lattices of many rockforming minerals. Instead, according to United States Mineral Resources (US Geological Survey Professional Paper 820) as the magma crystallizes, a portion of the uranium is deposited as an intergranular film on rock forming minerals, enters accessory minerals, or forms its own minerals. The remaining uranium becomes concentrated in magmatic differentiates, where it forms minerals in pegmatites and veins.

Jan 10, 1978

By Alvin Kaufman

ANTHRACITE mining in the United States is concentrated in a 480 sq mile section of north- eastern Pennsylvania. The producing area is broken up into four fields, known as the Northern, Southern, Eastern Middle and Western Middle fields. These areas represent intricately folded coal measures in synclinal residuals left by erosional forces. Destruction by erosion has eliminated some 95 pct of the original coal. However, discounting the 5 billion tons removed to date, 8 billion tons are believed to be still recoverable.

Jan 3, 1953

By Charles T. Malcomson

In the United States, improvements in methods of combustion have made possible the use of the smaller sizes of anthracite. This coal is now being reclaimed from the culm banks accumulated by the miners in the more prodigal years. To-day the freshly mined "slush" is segrega,ted and stored against the time when, through briquetting or some other means, it may be utilized as a commercial fuel. For many years Europe has achieved enviable results in the conservation of her small coal by briquetting. This profitable industry, first placed on a commercial basis in France in 1842, has grown to such magnitude that the production during 1913 exceeded 36,000,000 short tons. Briquets produced in Great Britain are used principally for steam purposes and the greater part of the output is either exported or taken by the Admiralty. On the Continent the briquets are sold in all branches of the coal trade. The French railways consume from 16 to 40 per cent. of their fuel in briquet form, and in Germany the lignite briquets (of which 20,000,000 tons were produced in 1913) are as familiar and interesting to the American traveler as the huge porcelain stoves in which they are burned. It is not strange, therefore, that aggressive and far-sighted promoters heralded this means of converting our ubiquitous coal waste into revenue. To the superficial student the briquetting process seemed so simple as to make success easy. It is for this reason principally that the path of the industry in America has been strewn with failures. The rash enthusiast had either not worked out the mechanical problems involved or had failed to grasp the local conditions under which the briquets must be made and sold. It may be confidently stated, however, that in spite of the many vicissitudes through which it has passed, coal briquetting is now an accomplished economic success in this country, and as a profitable adjunct to the coal industry it has come to stay. Several valuable contributions relating to coal briquetting are found in the Transactions. Charles Dorrance, Jr., has sketched briefly the history of the anthracite briquetting plants from the time of Loiseau's pioneer plant down to that of the Lehigh Coal & Navigation Co. at Lans-ford. Since then this phase of the industry has remained practically at

Jan 1, 1915

By H. C. Fiedler

THE development of the cube-on-edge secondary re-crystallization texture in Si-Fe strip depends upon the ability of inclusions to restrain normal grain growth. This ability is determined by the number and size of inclusions, which, for a given composition, is controlled by the thermal history of the material during the prior processing.' It has been shown2 that increasing the silicon content decreases the solubility of sulfur, and it is the purpose of this note to show the consequences of this decreased solubility for secondary recrystallization. Heats were made as previously described and cast into graphite molds.' The compositions are shown in Table I. Slabs 1 in. thick were cut from the ingots and either hot-rolled from 1000°C in the as-cast condition or after one of the heat treatments described later. The processing to the final gage of 12 mils followed the previous procedure.' To avoid cracking, the 5.2 pct Si alloy was cold-rolled at 150" to 200°C rather than at room temperature. The percent cube-on-edge texture developed by isothermal heat treatments was determined by dividing the maximum torque measured on disk sam-

Jan 1, 1968

By R. Henry Norton

The State of Oregon, although admitted into the Union February 14, 1859, is to-day, so far as any practical knowledge of its mineral resources is concerned, almost terra incognita, as compared with the other Western States and Territories. This is partly to be accounted for by the class of emigrants who first settled in the country ; they seem to have been, as they still are, a pastoral community, to whom the terms " mines " 'and " mining " are synonymous with bankruptcy and disaster, and who discourage all attempts to develop the mineral resources of the State. This statement is emphasized by the fact that Oregon has no State Geolo-

Jan 1, 1891

By F. P. Dewey

RICH HILL is situated in the famous car-wheel iron region of Southwestern Virginia, and although it contains many iron ores, this paper will be devoted chiefly to its car-wheel ore. Geologically, Rich Hill is somewhat difficult to describe, as the strata of the region are seriously folded and contorted. It lies at the base of one of the primordial spurs of the Blue Ridge, the ore appearing as a sedimentary deposit on the limestone No. 2, sometimes showing an imperfect stratification, but generally being an

Jan 1, 1882

By M. N. Dastur

In this paper, the current situation in iron ore pelletization in developing countries is reviewed. The main reasons leading to the development of pelletizing in these countries, alternative pelletizing methods and feed materials utilised, are illustrated with typical examples. The major factors which may influence the future growth are discussed and trends of development in the immediate future, till 1978, examined. The probable pelletizing capacity by 1985 is projected.

Jan 1, 1977

By Karl J. Benecke

Though the first patent on a bucket wheel excavator (BWE) was granted in 1881 in the US, this technology was developed in Germany to the high standards of today. However, this development was only possible in parallel with development of shiftable belt conveyors and boom stackers. The combination of these three types of equipment in the open pits of the Federal Republic of Germany has made lignite the cheapest energy source for power generation, despite the low heating value of German lignite on the order of 8500 kJ/kg (3600 Btu/lb) only. Comparing the costs for fuels used in power generating on the basis of their heating value, the relation between lignite, high quality black coal, and imported crude oil is on the order of 1 to 1.5 to 2.5, hence highly in favour of lignite. These cost advantages for lignite in Germany are due mainly to the concentration of lignite mining in a few high-output mines. The largest one, Fortuna mine in the Cologne district, produced a total of 45 million tons of lignite in 1976. That equals the annual fuel need of a 5750 MW power plant running 7000 hours per year at full capacity. Altogether 95.2 million bank m3 equal to 200 million tons of overburden had to be removed to accomplish this lignite output. The largest BWE ever built is working in the Fortuna mine [(Fig. 1)]. At a digging height of 51 m above crawler level, the total vertical reach in relation to the face conveyor level is 98 m by means of its conveying bridge and loading unit. The hourly output is 10 400 bank m3. Its weight in operation is 13 000 tons and its wheel diameter 21.6 m, as high as a seven-story building. Major reasons for the development of BWE technology in Germany were: ? Lignite deposits with moderately consolidated, alluvial-type overburden (gravel, sand, loam, marl, clay, etc.) ? Great overall depth of the deposits, ranging far beyond 100 m, requiring a wide opening of the mine, hence not permitting direct overcasting of overburden. ? Multiple-seam deposits of poor-quality coal divided by reject partings, which demand a perfectly selective digging tool for clean separation. In general, these conditions are almost identical to those prevailing in the lignite deposits of Texas and neighbouring states: The type of overburden suitable for BWE digging, the overall deposit depth ranges down to around 100 m, and finally, the multi-seam occurrence with partings between seams, the latter ranging from just 1 m to a few meters in thickness. Technique As the Texas-type lignite deposits come into focus more and more as a possible fuel source in power plants to replace natural gas and crude oil, the following will deal with the BWE technology for mining a typical Texas lignite deposit under the aspect of producing enough fuel for a 500-MW power plant located at the mine mouth.

Jan 1, 1980

By Gordon E. Agar, David M. Hopstock

This paper describes the procedures and results of a series of experiments conducted to determine the depressing effect of sodium, calcium and magnesium ions on the amine flotation of quartz. It also presents an analysis of the experimental results by the electrical double layer theory. The flotation of quartz with primary amines has been practiced on a large scale in the phosphate industry for many years. Some glass sand —and recently iron ore — has also been treated by this flotation technique. These applications have been highly successful and demonstrate that a complete mastery of all the details of an operation is not needed to achieve an economic success. There are times, though, when it becomes important to recognize, both qualitatively and quantitatively, the effects of some previously ignored variables. The effects of cations on the amine flotation process, particularly those ions that contribute to water hardness and abound in sea water, are a case in point. In conjunction with the development of a cationic flotation reagent for separating quartz from apatite, it became necessary to quantify the influence of calcium and magnesium on the separation. In order to strengthen and broaden current understanding of the flotation process, the results were interpreted by means of the electrical double layer theory. THEORETICAL BACKGROUND Assume that, given the same equipment, procedure, and time, the recovery of quartz by amine flotation is a function of only the adsorption density of aminium ions in the Stern layer, i.e., that for any given adsorption density there exists only one recovery percentage. By the Stern-Grahame treatment of the electrical double layer,'-' for any ionic species in a solution in equilibrium with quartz,

Jan 1, 1969

By Julian Avery

IN its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary pur-pose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by com-bustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the effi-ciency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure; i.e., the "top pressure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity.

Jan 1, 1938

By J. W. Bolton

THIS paper discusses some fundamental metallurgical principles involved in production of sound cast bronze. In a previous paper the writers advanced the theory that "oxidation" in bronze castings is due to incipient shrinkage, and showed the effect of reducing melting atmospheres. In the present paper the effects of certain impurities and of actual oxidizing conditions are shown. The appendix deals with the appearance of various inclusions. For many years the prevailing opinion has been that unsoundness, dark colored fractures and other phenomena accompanying porosity and weakness in bronzes are due to oxidation. The actual troubles are caused by fissures of intercrystalline type, which are often mistaken for intercrystalline films. These weaken the metal and make it porous. Grave doubt regarding the accuracy of the oxidation theory appears when several research papers presented within the last 10 years are reviewed critically. In 1919, Comstock conducted metallographic researches, attempting to identify "oxides" in synthetically prepared metals. He found that oxides of tin, aluminum, zinc, etc. are different from the intercrystalline films (or cavities) to which porosity is due. Apparently he believed that these "oxide films" may be caused by volatile oxides of zinc or of phosphorus or by dissolved gases thrown out of solution during solidi-fication of the metal. In 1923, Woyski and Boeck3 definitely questioned the accuracy of the oxidation theory and indicated the danger from reducing atmospheres. They say that "oxidation, gassing and shrinkage may produce effects very similar."

Jan 1, 1930

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen's regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By Cecil Hagen

All of the production for Ecuador during 1940 came from the Santa Elena Peninsula, Province of Guayas; the major portion coming from the Ancon field, which is controlled mostly by Anglo-Ecuadorian Oilfields, Ltd. A small amount was produced from the shallow pumpers and pozos, or oil pits, at Cautivo-Achallan, Carolina, Santa Paula, Concepcion, El Tambo and Mina Tigre. Considerable exploration was carried on in the country during 1940 and numerous concessions were in force, as shown by the accompanyiag map. Anglo-Saxon continued its exploratory work in the Oriente by surface geological methods and some geophysical surveys. It is understood that this concern did considerable airplane mapping. International Petroleum, on its large concessions between the Andes and Pacific Coast, did considerable surface work as well as some geophysical. No exploratory test wells were drilled by either of these

Jan 1, 1941

By Cecil Hagen

All of the production for Ecuador during 1940 came from the Santa Elena Peninsula, Province of Guayas; the major portion coming from the Ancon field, which is controlled mostly by Anglo-Ecuadorian Oilfields, Ltd. A small amount was produced from the shallow pumpers and pozos, or oil pits, at Cautivo-Achallan, Carolina, Santa Paula, Concepcion, El Tambo and Mina Tigre. Considerable exploration was carried on in the country during 1940 and numerous concessions were in force, as shown by the accompanyiag map. Anglo-Saxon continued its exploratory work in the Oriente by surface geological methods and some geophysical surveys. It is understood that this concern did considerable airplane mapping. International Petroleum, on its large concessions between the Andes and Pacific Coast, did considerable surface work as well as some geophysical. No exploratory test wells were drilled by either of these

Jan 1, 1941

By Josef Westesson

No question in the metallurgical chemistry of the present day seems to be so difficult to agree upon as the determination of phosphorus in iron and steel. To my knowledge, there are at present at least three different methods in use in the iron laboratories of the United States, viz.: The citric acid method, the molybdate-magnesia method, and the direct molybdate method,—the last-named method having been lately adopted. Each of these methods has its advocates, who take every pains to prove its advantages, and the incorrectness of the others; and much has been written for the purpose of securing the use of a standard method—as yet, however, without any result. There is no doubt, or ought to be none, that each of these methods gives correct results, when it is carefully conducted and every precaution is taken. But it is not only correct results that we want nowa-days. The demand is great, also, for getting results in the shortest possible time. I think it has been sufficiently proved that the direct molybdate method, the weighing of the precipitate, answers well in both respects. Being a pupil of Prof. Eggertz, I have myself used his method for years until quite recently, as it is described by Mr. Troilius in our Transactions, vol. x., p. 166 (but with some slight modifications), and I can safely say that the results of this method agree well with those of the molybdate-magnesia method. I have, moreover, been checked, in a few instances, by some of the

Jan 1, 1885

By M. G. Corson

INFORMATION regarding the use of manganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties .and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists.1 PROPERTIES OF MANGANESE Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850° C. and the other below 650° C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the silicides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available.

Jan 1, 1927