Search Documents

By Mark J. Klein, Robert A. Haggins

The pesence of a small amount of oxygen was found to cause significant grain growth restraint in 99.99 pct Ag. This behavior does not seem to be due to the presence of an oxide dispersion, but instead, to be related to the existence of minute amounts of oxygen m solid solution. In the amounts necessary to cause the observed effects it was found that oxygen migrates with extreme rapidity, probably along extended structural imperfections, such as dislocations and grain boundaries. A number of years ago, hastton' observed that the presence of small amounts of oxygen caused a retardation of grain growth in silver. He attributed this behavior to the formation of a fine dispersion of oxide particles by the internal oxidation of trace impurities. More recently, wood2 also found that oxygen caused grain growth restraint in copper. Experiments using both copper and a dilute solution of aluminum in copper led to the conclusion that the effects observed in copper were due to oxygen in solid solution, rather than an oxide dispersion. During the course of a study of the influence of several solutes on the recrystallization of Silver, the presence of minute amounts of oxygen was found to exert a very significant influence on grain growth. The experiments reported here were undertaken to determine whether the grain growth restraint observed in silver due to the presence of oxygen is related to oxygen in solution or to an oxide dispersion. Because of the difficulty in measurement and control of the very small oxygen concentrations causing the observed effects no attempt was made to treat the data in a quantitative manner. EXPERIMENTAL PROCEDURE AND RESULTS Silver of 99.99 pct purity was melted and cast into slabs in a vacuum of better than 0.1 p. These slabs were reduced 50 pct by cold rolling to a thickness of approximately 2.5 mm. Samples cut from this material were annealed in vacuum for a series of different times at 803°C. Another group of samples was similarly annealed in air. This temperature is well above the recrystallization range for silver of this purity (150" to 200°C). The mean grain diameter of these samples was measured, both in the center and near the edge, using the line-intel-cept method, and is shown as a function of annealing time in Fig. 1. The grain size in the centers of the samples annealed in air was found to be larger than that of the surface regions, while the grain growth behavior of the edge and center regions annealed in a vacuum was approximately the same. he edge measurements were taken at a distance of 0.2 mm from the surface.) A few samples were annealed in nitrogen. Their behavior was identical to that of the vacuum-annealed samples. Samples annealed in oxygen had approximately the same grain growth behavior as those annealed in air, leading to the conclusion that this behaviouer is due to oxygen. The microstructure of a sample annealed in air at 803" for. 30 minutes is shown in Fig. 2. The smaller grain size near the surface is characteristic of the iir-annealed specimens. Possible causes of this grain growth restraint in the air-annealed specimen are the formation of an im-

Jan 1, 1962

By T. A. Dungan

THE thermal processes for the production of metallic magnesium can be divided into two general classifications, the direct reduction of magnesia with carbon and the indirect reduction of compounds of magnesium by reducing agents that are themselves products of carbon reduction. The latter are so chosen as to cause reduction of magnesium compounds wherein only the magnesium is liberated in the vapor phase. Reducing agents used are: calcium carbide, silicon carbide, silicon, aluminum, various silicides or combinations of calcium, aluminum, silicon in iron. All of these are products of highly endothermic reactions and, with the exception of scrap aluminum, can be produced in an open, submerged arc furnace; that is, the arc is covered only by the charge itself. The more investment in energy required to prepare such a reducing agent, the less is the energy required in the subsequent step to reduce the magnesium compound to the metal. It is impossible, however, to avoid the laws of thermodynamics, no matter how much circumambulation is resorted to in the preparation of successively more powerful reducing agents. Since each such step carries forward its own inefficiencies, it appears evident that the ultimate status of such processes is dependent upon the development of by-products. EARLY EXPERIMENTS IN DIRECT REDUCTION The direct reduction of magnesium oxide by carbon has a decided appeal to both the scientist and the industrialist. The successful production of the carbothermic plant at Permanente is a significant fact in the substantiation of this concept. Like most developments, however, the history of carbon reduction of magnesia is not one of triumph after triumph, or immediate heady success to the investigators. It is understood that one of the early investigators conducted an experiment wherein he placed carbon and magnesia in one end of an evacuated tube and managed to heat this end to a temperature high enough that magnesia and carbon deposited at the other end of the tube. The charge, unreduced, appeared to have been completely transported from the hot to the cold end of the tube. This raised doubt for some time as to whether magnesia could be reduced at all with carbon. It was correctly suspected, however, that the magnesia was in fact reduced and the resultant magnesium vapor and carbon monoxide reacted upon one another upon reduction in temperature to reform the starting ingredients. Attempts were then made to dilute the two vapors by passing a considerable stream of hydrogen through an arc furnace charged with magnesia and carbon. Thus by dilution of the products it was expected to obtain metallic magnesium. The results were positive and metallic magnesium was

Jan 1, 1944

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By Gardner F. Williams

These mines are situated in Griqualand West, which is now a part of the Cape Colony. The town of Kimberley is in latitude 28o40' South, longitude 25o10' East, about 640 miles northeast of Cape Town and 450 miles from Port Elizabeth on the east coast. It is connected with these towns by a railroad, which has been completed during the present year. The mines are located in a desert country, resembling the desert portion of Arizona. The elevation above sea-level is about 4000 feet. The climate is exceedingly hot during the summer months. Diamond Deposits.—There are four large diamond-bearing deposits at Kimberley, all lying within a radius of one and one-half miles, having the De Beers mine as the center. These are named the " Kimberley," " De Beers," " Du Toit's Pan," and " Bultfontein " mines. There is, also, directly west of the Kimberley mine, a small deposit, called " St. Augustiue," which has been prospected only, and

Jan 1, 1887

By James K. Hallenburg

INTRODUCTION The delayed fission neutron, or DFN technique for uranium ore body analysis uses the first down-hole method for detecting uranium in place quantitatively. This technique detects the presence of and measures the amount of uranium in the formation. DFN TECHNIQUE DESCRIPTION The DFN technique depends upon inducing a fission reaction in the formation uranium with neutrons, resulting in an anomalous and quantitative return of neutrons from the uranium. Since there are no free, natural neutrons in formation, a good, low noise assessment may be made. There are several methods available for determining uranium quantity in situ. The method used by Century uses an electrical source of neutrons. This is a linear accelerator which bombards a tritium target with high velocity deuterium ions. The resulting reaction emits high energy neutrons which diffuse into the surrounding formation. They lose most of their energy until they come to thermal equilibrium with the formation. Upon encountering a fissile material, such as uranium, these thermal neutrons will react with the material. These reactions produce additional neutrons, the number of which is a function of the number of original neutrons and the amount of fissile material exposed. The particular source used, the linear accelerator, has several distinct advantages over other types of sources: 1. It can be turned off. Thus, it does not constitute a radioactive hazard when it is not in use. 2. It can be gated on in short bursts (6 to 8 microseconds). This results in measurements free of a high background of primary neutrons. 3. The output can be controlled. Thus, the neutron output can be made the same in a number of tools, easily and automatically. There are several interesting reactions which take place during the lifetime of the neutrons around the source. During the slowing down or moderating process the neutron can react with several elements. One of these is oxygen 17. This results in a background level of neutrons in any of the measurements which must be accounted for in any interpretation technique. These elements are usually uninteresting economically. The high energy neutrons will also react with uranium 238. However, the proportions of uranium 235 and 238 are nearly constant. Therefore, this reaction aids detection of uranium mineral and need not be seperated out. Upon reaching thermal energy the neutrons will react with any fissile material, uranium 235, uranium 234, and thorium 232. At present, we do not have good techniques for seperating out the reaction products of uranium 234 and thorium 232. However, uranium 234 is a small (.0055%) percentage of the uranium mineral and thorium 232 is usually not present in sedimentary deposits. When the uranium 235 reacts with thermal neutrons it breaks into two or more fragments and some neutrons. This occurs within a few microseconds after the primary neutrons have moderated and is the prompt reaction. One system uses this; the PFN or prompt fission neutron technique. We don't use this method because the neutron population is low and, therefore, the signal is small and difficult to work with, accurately. Within a few microseconds to several seconds the fission fragments also decay with the emmission of additional neutrons. Now, with a long time period available and a large neutron population we gate off the generator and measure the delayed fission neutrons after a waiting period. These neutrons can be a measure of the amount of uranium present around the probe. Thermal neutrons are detected with the DFN technique instead of capture gamma rays to avoid some of the returns from other elements than uranium. LOGGING TECHNIQUE The exact logging technique will depend, to some extent, upon the purpose of the measurement. However, the general technique is to first run the standard logs. These will include: 1. The gamma ray log for initial evaluation of the mineral body and for determining the position of the borehole within the mineral body, 2. The resistance or resistivity log for determining the formation quality, lithology, and porosity. 3. The S. P. curve for estimating the redox state and shale content, and measuring formation water salinity, 4. The hole deviation for locating the position, depth, and thickness of the mineral (and other formations), and 5. The neutron porosity curve. The neutron porosity curve is most important to the interpretation of the DFN readings. The neutrons from this tool are affected in the same way by bore hole and formation fluids as the DFN neutrons are. Therefore, we can use this curve to determine effect of the oxygen 17 in the water. Of course, this curve can be used to determine formation porosity. It can also be used to calculate formation density.

Jan 1, 1979

By N. A. Richard, A. E. Austin, R. E. Maringer

AS part of a detailed study of the structure of metallic meteorites, the concentration and distribution of iron and nickel in the various phases of meteor -itic iron have been measured using an electron-probe microanalyzer. The specimen used was cut from a position about 3 in. below the surface of the Grant meteorite, a one-half-ton iron specimen (containing 9.35 pct Ni) found in New Mexico some years ago. A photomicrograph showing the general Widmanstztten structure, somewhat typical of iron meteorites, is shown in Fig. 1. The line across which the analyses were made is indicated by arrows. This area was chosen so as to evaluate the iron-nickel concentration in the three principal phases visible in Fig. 1. These phases, in the language of meteoritics, are kamacite, taenite, and plessite. Kamacite is the a-

Jan 1, 1960

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By H. A. Burgman

During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other elements (uranium and selenium) that are mobilized during the leaching process, have also been found in post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and, thus, greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid increase in permeability.

Jan 1, 1985

By N. S. Stoloff, R. G. Davies

The annealing behavior of a heavily cold-worked FeCo-V alloy has been studied at temperatures both above and below Tc, the critical temperature for ordering. It was found that re crystallization and grain growth can take place below Tc in the ordered state and that, in agreement with results for fcc alloys, order retards grain growth. The activation energy for pain growth is -55 kcal per mole in the disordered condition; it was not possible to assign a value to the activation energy for grain growth below Tc because the degree of order is changing rapidly over the temperature interval investigated. Precipitation of an fcc y phase was observed upon annealing the cold-worked alloy at temperatures of 675°C and below. SINCE it is known that diffusion constants are greatly affected by long-range order,' it is not unreasonable to anticipate that order will influence the diffusion-controlled phenomena of recrystallization and grain growth. In the course of a study of strain aging of ordering alloys around the composition Ni3Fe Vidoz, Lazarevic, and cahn2 noted that a disordered cold-worked alloy annealed at a temperature T1 just below Tc will order but not recrystallize; Tc is the critical temperature for order. The same alloy annealed at a temperature T2 just above Tc, or an alloy of different (nonordering) composition annealed at either T1 or T2, will recrystallize after equivalent amounts of cold work. Initially Selisskii and coworkers,3,4 who examined a series of cold-worked and annealed bcc Fe- Co alloys, reported that alloys forming the B2 FeCo super lattice could not be recrystallized below Tc. However in a later paper5 it was shown that FeCo ordered alloys could be recrystallized below Tc. Thus the first question to be answered by the present investigation was whether or not a heavily cold-worked Fe-Co-V alloy could be recrystallized below Tc. When it was found that the alloy would indeed re-crystallize below Tc, the influence of long-range order upon subsequent grain growth was studied. EXPERIMENTAL PROCEDURE The grain-growth measurements were made upon FeCo-2 pct V wire of 0.031 in. diam; the alloy was the same as that used in an earlier study of the mechanical properties of FeCO-v.6 The wire was produced by cold swageing and drawing a rod 0.125 in. diam that had been quenched into iced brine from 850°C to disorder the alloy; the initial grain size was 0.05 mm. Rates of grain browth were measured after isother-mally annealing the wire in the temperature range 675° to 825°C; T, is -720°C. Grain diameters were measured on the transverse cross section of the wires. The line-intercept method of determining the grain diameter was used; conventional light photomicrographs were taken when the grain size was greater than 10 . Carbon replicas were produced and examined in the electron microscope if the grain size was less than Dislocation configurations after recrystallization anneals were studied by electron transmission microscopy of foils produced by cold rolling a 0.125-in.-thick strip of the quenched material to 0.012 in. The foils, after heat treatments similar to the wire samples, were thinned by electropolishing in a chromic-

Jan 1, 1967

By C. V. O. Hughes

Florida phosphate operations are unique in the ways standard mining equipment is made to meet specialized problems. Hydraulic mining and transportation has evolved in meeting three such special problems: 1) surface mining of a shallow, poorly consolidated but wet material; 2) high pro¬duction rates, necessary because of low prices for phosphate rock in a highly competitive market; and 3) preparation of the value-bearing rock, or matrix, for washing and flotation. The magnitude of the problems is better appreciated if the reader understands the size of operations in the area. The Florida phosphate field produces and ships about 10 million tons per year of phosphate rock. All of this has to be concentrated to its shipping grade, either by scrubbing and screening or by flotation.

Jan 1, 1956

By Edel Moldenke

BURMA has long been known for its ruby, tungsten, and tin deposits, and, lately, for having the largest lead-zinc mine in the world, the Bawdwin Mine of the Burma Corpn. All the coal used, however, is imported from Calcutta; this is a bituminous coal of about 11,000 B.t.u., 24 per FIG. 1.-MAP SHOWING LOCATION OF COAL FIELDS AND TRANSPORTATION ROUTES. cent. ash, and costs about $8 per ton. Bituminous coal has not, thus far, been found, but many lignite deposits are known. The most promising lignite deposits are in the Namma field, Fig. 1, situated in the Northern Shan States of Upper Burma, about 30 mi. south of Lashio, the terminus of the Burma Railway, 750 mi. north of Rangoon. The

Jan 7, 1921

By V. A. Zanadvoroff

THE mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse sands, representing 60 to 70 per cent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. GENERAL CONSIDERATIONS The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. TAILING-DISPOSAL SITES The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.-Covers approximately 10 acres. Built up to the height of 60 ft.

Jan 1, 1946

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

By Cyril Smith

A STUDY of the mechanical properties of the alloys of copper and silver led to the discovery that the solubility of silver in copper was greatly different from that generally supposed, therefore some work was done to determine the solubility with greater accuracy than had previously been achieved. After the work had been completed, two papers were published1 giving solubility figures which agreed closely with one another and with the work described herein. A detailed comparison of that work with the present will be given later. PREPARATION OF ALLOYS The copper used in making the alloys was electrolytic ingot of high purity. The silver was prepared by precipitation as chloride from nitric acid solution, followed by fusion of the washed precipitate with sodium carbonate and potassium nitrate. This method gives metal containing at least 99.99 per cent silver. The copper was first melted under charcoal in a small electric resistance furnace and the silver added as pure silver, it being unnecessary to make any intermediate alloys. After thorough stirring the metal was poured into a mold of suitable form. The alloys contained between 0.008 and 0.015 percent of oxygen. Small amounts of oxide were visible under the microscope, but it is not believed this would have much effect on the results. Copper-silver alloys are notorious for segregation, consequently a few experiments were carried out to find a form of casting with as little segregation as possible. A mold 6 in. long and 1/2-in. dia. was first used, and an alloy nominally containing 5 per cent silver was cast in it, while some of the same alloy was poured directly into water to obtain the maximum rate of cooling possible. Analyses were made both on this sample and on turnings from the top and bottom of the 1/2-in. dia. casting, the turnings being separated into three parts according to the position

Jan 1, 1931

By John S. Alexander

DURING the past few years the block coal of Indiana has been talked about and written upon to such an extent, that almost every one at all interested in such subjects, has been made acquainted with the area and geographical position of the field, the quality and peculiar properties of the coal, the thickness of the veins, the manner of mining, etc. The writer, therefore, taking for granted that, to those present all this is familiar ground, desires more especially to call attention to the position this coal takes in the market, and at those points of consumption where it is brought in direct competition with rival fuels. Chicago, thus far, has been the chief consumer of Indiana block coal, the distance from the mines at Brazil, via Terre Haute and the

By Chikaosa Tanimoto

INTRODUCTION The committee on Rock Mechanics, Japanese Society for Civil Engineers, has been discussing 'soft rock engineering in Japan' and presented several papers concerning dam, tunnel, bridge and slope constructions to International Symposium on Weak Rock, Tokyo 1981. This is the summarized paper based on References of Okamoto et a1 (1981), Iida et a1 (1981), Working Group on Tunneling-JSCE (1981), Working Group on Bridge Foundations-JSCE (1951) and Kikuchi et a1 (1981), which can convey general view on engineering experiences with weak rocks in Japan. From the point of view to the origin and/or distinctive physical properties, weak rocks in Japan may be classified into (1) sedimentary, (2) weathered, (3) low welded-pyroclastic and (4) fractured ones. Their typical characteristics are summarized in the following section. Concerning dam foundations on soft rock, several hundreds have already been constructed and, at present, nearly one hundred are under construction or at planning stage. These dams, almost without exception, have some problems such as site selection, material selection for fill-type and concrete dams, design of dam and its foundation, and construction procedures, requiring special ingeneous and cautious measures to cope with the local geotechnical difficult situations. In tunneling, for the decade of 1970s, the number of tunnels in soft rock either completed or under construction was at least 160, including Seikan Tunnel of 53.9 km long, Nakayama Tunnel of 14.8 km long and so on. Most of these tunnels are distributed in the northern half of Mainland, consisting of a basement of Paleozoic strata and Plutonic rocks, overlayed by Neogene Tertiary formations which include large

Jan 1, 1982

IF you wish to make the acid that is vulgarly called common aqua fortis,* for parting gold from silver, you must first provide as many cucurbits and alembics, receivers, and materials as you wish, and then make a furnace that is long and conveniently wide for holding three or four pairs of cucurbits or as many as you wish. If you have to make this by art in order to work a large quantity, you could make several small furnaces for it seems that not more than three or four pairs are suitable for one. Prepare the places where the cucurbits are to stand with bottoms or covers made of potter's clay or tiles that are half round like the bottoms of the cucurbits and have a little rim around the top so that they can be built in. Proceed to build these in in pairs, one by the other with convenient spaces between, placing an iron support across to make this place stronger and more secure. In every corner and also in the middle a hole must be made as a vent for the smoke, as is done in all furnaces. You will see the form of this somewhat roughly drawn here. [Figure 25] Near this prepare a number of cucurbits which are made of glass, as clear and uniform as possible and very well formed. There must be no bubbles or other indentations in these, for they would be dangerous and uncertain for your work. Lute these with lutum sapientiae up to within three dita or less from where the neck narrows. This lute must be spread out well all over to the thickness of two threads or a little more. Then cover and make them strong with this well-made plaster, and finally dry it, taking care that there are no clefts or cracks such as clays are often prone to make even though they be well prepared. For greater security choose among these [64v] a clay that is lean and then mix it with at least a fourth part or more of wool-clloth clippings and about an eighth part of wash

Jan 1, 1942

By F. F. Aplan

INTRODUCTION Coal is a solid combustible mineral substance resulting from the alteration of vegetable matter largely in the absence of air. It occurs in nature with varying percentages of mineral matter associated with and incorporated into the coalified material. If the amount of this inorganic mineral matter is sufficiently small, and if selective mining can be practiced so as to avoid the incorporation of ash- bearing material from adjacent strata and/or parting seams, the coal can be used as-mined. Otherwise, it must be given a preparation treatment. In 1980 the bulk of the approximately 525 coal preparation plants were located in the eastern half of the U.S., largely in the Appalachian and to a lesser extent in the midwest coal fields (1). Only 17 of these preparation plants were located in the west; these were in Colorado, New Mexico, Utah, Washington and Wyoming. In the past, however, a great many more preparation plants were operated in these and other western states. The upsurge in both the domestic and world- wide demand for quality coking and steam coal will certainly lead to an increase in the number of preparation plants in the west. In fact, there has been a massive development of coal mines and their associated preparation plants across our northern border in Alberta and British Columbia, largely to serve the export coking and steam coal market. Most of the tremendous increase in newly-mined coal in the western U.S. has come from thick seams of inherently low-sulfur, low- ash coal, easy to mine selectively without significant contamination with ash-forming minerals and requiring no preparation. Because of

Jan 1, 1983

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south-eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States.1 Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). TABLE 1.-Physical and Chemical Composition of Different Types of Clays Composition, Per Cent Constituents and Properties Bentonite Fuller's Mud Clay (Wyoming) Earth (P Peak)' (Alluvial) Silica (SiO2) 60.0 69.6 61.67 Alumina (Al203) 19.0 14.3 20.34 Ferric oxide (Fe203) 2.8 3.90 7.70 Titanium oxide (Ti02) 0.13 0.70 1.01 Lime (CaO) 0.5 0.80 0.00 Magnesia (MgO) 2.0 1.00 0.24 Soda (Na2O) 2.4 0.40 0.31 Ignition loss 4.7 6.77 8.51 Moisture content 8.0 10.0 20.0 Isoelectric point, pH 9.2 9.2 6.5 Average swelling volume 15.0 0.0 0.0 Weight per cubic foot, lb 55.0 40.0 65.0 Material passing 200-mesh sieve, per cent 90.0 85.0 50.0

Jan 1, 1939

By Herbert A. Wendel

Reaching the miner with safety education" is R the ultimate goal, the main objective, of every safety program in the mining industry. If we can get safety education to every worker, and it is properly learned, enforced and obeyed, we should eliminate at least 85% of all potential accidents. We should then have very few accidents as a result of unsafe behavior, which, in turn, would allow us to concentrate most of our future efforts on preventing the types of accidents which are caused by faulty or defective machinery, equipment, tools and materials. An uninformed or uninitiated person would think that it should be a rather simple process to reach the miner with a safety education. Theoretically he would be right because here we get involved in a matter of semantics. When we say "reaching the miner with safety education" we actually mean that this education must also be accepted and learned by the miner; we intend to mean that safety must be observed and followed at all times. But in order to realize our complete meaning of the phrase, we must find the solution for a number of problems and obstacles which are well known to management and safety personnel.

Jan 1, 1965