Search Documents

By E. J. Longyear

The rapid development of the Mesabi range has been a matter of much wonder to those familiar with ore-deposits elsewhere, and much skepticism was shown when " millions of tons of ore on the Mesabi" was first reported. Now, however, with over 8,000,000 tons to its credit at the close of 1896, a prospect of 3,000,000 more this year, and more ore " in sight" than ever before, it is evident that the first claims for the range were not so greatly exaggerated as perhaps even those who made them thought they were at that time. An explanation of the ease with which these deposits have been explored is found in their mode of occurrence. Lying in flat beds and near the surface, and only exceptionally occurring under a taconite " capping," the prospector had only to sink a few vertical test-pits on a fortyacre tract down to the rock to be reasonably sure whether his property contained ore or not. If he found ore in one or more of these preliminary pits, he would then fill in with more pits until the ore-area was entirely outlined by test-pits from 200 to 400 feet apart. In the early days of the range the testing was almost entirely done by digging pits with pick and shovel. When water was encountered, work had to be stopped, unless a steam pumping-plant was put in, resulting in greatly-increased expenses. Latterly, drills have been used with great success in continuing the exploration after water has been struck in the pit, rendering further progress with pick and shovel impracticable. There are several kinds of drills in use. The diamond-drill is largely used, and possesses the advantage of being in readiness to drill rock if thought advisable, the taconite being very hard and almost impossible to drill except by the use of diamonds. Some form of churn-drill has been much used. This may be either a steam- or a horse-power-drill. The principle is the same in each, the cutting being done by percussion instead of by rotation, as in the case of the diamond-drill. A churning motion is given by passing a rope from the top of the

Jan 1, 1898

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;'-' and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

By William B. Phillips

The possible sources of potash salts in the United States have been considered from many points of view during the last several years, but it is only within the last two or three months that the situation has become acute. We import from Germany, the only sourcc of large supply, more than $10,000,000 worth of potash salts annually, and this business has been badly crippled by the European war. If there was ever a time in our industrial existence when the necessity of providing for our own needs was more acute than it is now, we are not aware of it. One has only to study the price lists of chemicals sent out by the large supply houses to see the change wrought within a very short time. Whether or not these prices are to maintain for a considerable time, no one can say; but it appears to be probable that we shall not see prices materially lower for a period of uncomfortable length, to say the least. It is not my purpose at this time to discuss the various sources of supply of potash salts that have been suggested or recommended. Some of them might afford a pleasing relief but all of them combined would not affect the situation seriously. If we are to have our own sources of potash salts, they will have to compare, in some efficient manner, with the sources upon which we have drawn during the last 20 or 30 years; i.e., they must exist in minable quantities. It seems to me to be quite idle to speculate upon our domestic sources of potash if those sources are not of a character similar to those upon which we have so long depended. A few thousand or, perhaps, a few hundred thousand dollars' worth of chemically derived potash may be produced under the stress of present conditions, but when we consider that each year demands more than $10,000,000 worth, we must look to underground sources; we must look to mines similar to the famous Stassfurt and Halle deposits. If we cannot mine potash salts, we shall have to do without them for a while.

Jan 1, 1915

By H. E. Elliott, R. S. Busk, A. T. Peters

One of the problems of the fabricator of metals and alloys is the propensity of some composition rarnges toward abnoermal grain growth during certain stages of fabrication. In this respect magnesium alloys are no exception among alloys. Fortunately, convenient foundry control methods have been developed by which the abnormal grain growth possible in certain magnesium-alloy castings can be suppressed. An unusual characteristic of magnesium alloys, however, is that castings of some composition ranges are subject to local grain growth during heat-treatment without the necessity of intentional mechanical stressing of the part prior to heat-treatment. This effect occurs only under certain critical casting conditions, and only in certain alloys of greater than about 8.5 per cent aluminum content, such as C alloy (Mg, 9 per cent A1, 2 Per cent Zn, 0.2 Per cent Mn) and G alloy (Mg, 10 per cent Al, 0.2 per cent Mn). The first observation of this phenomenon in cast magnesium alloys occasioned much surprise, since it is not observed in other meta1s- Jeffries and Archer1 have stated that "the grain size of cast metals, provided they have not been plastically deformed, cannot be changed by heating below the melting point." The study of the conditions leading to abnormal grain growth in cast magnesium alloys, and of the mechanism of this phenomenon, has led to some very interesting observations. Perhaps the most significant of these was the observation that stresses originating from cooling contraction in magnesium-alloy castings are the only stresses necessary, under certain conditions, to cause local recrystallization and subsequent grain growth in the casting during heat-treatment. Before recent developments, this phenomenon of abnormal local grain growth Was a definite problem in the production foundry on C alloy sand castings. Illustrated (Fig. I) is a picture of a casting scrapped because of this defect. A mottled effect is produced in coarse-grained areas by suitable etching solutions. The properties of metal in the affected area are much impaired by such grain coarsening. Ultimate tensile strengths of half the normal value have been measured in metal of this nature. In this paper are described the techniques that have been developed by The DOW Chemical Co. for studying, and in large measure solving, this production problem. Also discussed are studies of the mechanism by which excessive grain coarsening occurs, and the fundamental conditions that produce this effect. The abnormal grain growth discussed in this paper will be referred to as "germinasium since this term has been definedl as any process leading to an abnormally coarse grain size. This paper deals only with abnormal local grain growth that may occur during the solution heat-treatment of certain magnesium-alloy castings, as dis-

Jan 1, 1945

By L. L. Seigle

Free energies, heats, and entropies of mixing of solid Fe-Au alloys have been measured by the galvanic cell method between 800° and 900°C. A positive deviation from Raoult's law and a large excess entropy of mixing were observed, both attributable to lattice distortion caused by the disparity in component atom sizes. Since the terminal solid solutortiontions are not regular, thermodynamic properties computed from the location of the mis-cibility gap do not agree well with measured quantities. The electromotive force data suggest some changes in the existing Fe-Au phase diagram. ALTHOUGH a considerable amount of information has been accumulated about the thermodynamic properties of metal solid solutions which exhibit negative deviation from Raoult's law, particularly those in which ordering occurs, relatively few experimental measurements have been made on solutions with positive deviation. This is due to the infrequency of broad homogeneous regions suitable for experimental measurement in solutions of this type, since any marked positive deviations from ideality lead to restricted solubility and the formation of miscibility gaps. Thermodynamic data reported in the literature for such systems have usually been calculated from the location of the miscibility gap boundaries under the assumption that the entropies of mixing are ideal, i.e., the terminal solutions are regular.' One of the few binary systems with both positive deviation and a wide homogeneous range in the solid is the Ni-Au system. A recent investigation of solid Ni-Au alloys' revealed that the entropies of mixing were much larger than ideal and consequently thermal data computed from the phase boundaries assuming regular solutions were seriously in error. Theoretical considerations put forward by Zener indicated that high entropy values should generally be associated with systems possessing a miscibility gap in the solid, when this is due to differences in the size of component atoms. These facts suggest that the regular solution assumption is a poor approximation for many solid solutions with positive deviation and that reliable thermodynamic data generally cannot be obtained by conventional methods from the location of miscibility gap boundaries. The Fe-Au system, Fig. 1, resembles the Ni-Au system in certain respects. The presence of a miscibility gap in the solid indicates a large positive deviation from ideality, but there is nevertheless an extensive single phase region suitable for experimental measurement. The following investigation of solid Fe-Au alloys was carried out in order to obtain additional data on the thermodynamic properties of metal solid solutions with positive deviation from Raoult's law and to further compare thermodynamic data computed from miscibility gap boundaries with those measured experimentally. Experimental Method The thermodynamic properties were derived from measurements of the potential developed between pure solid iron and Fe-Au alloys in a high temperature galvanic cell. The experimental apparatus and technique were the same as those used for the Ni-Au alloys and described in a previous report.' Cell electrodes were 1/16 in. diam rods swaged from chill-cast ingots and annealed for one week at 850°C. The alloys were prepared by melting fine gold granules under argon with pure iron obtained from the National Research Co. The cell electrolyte was

Jan 1, 1957

By William Johnson

IT is now recognized that several important types of reactions in metallic systems proceed by the formation of nuclei and the growth of these nuclei. The process of freezing is a simple example of this, as Tammann pointed out years ago.1 Tammann held that ' the rate, of freezing is determined by a rate of nucleation, expressed as the number of nuclei formed per unit volume of unfrozen liquid per second, and a rate of growth of these nuclei, expressed as the linear rate of radial growth in units of length per second. For isothermal freezing the conception is simple; for ordinary freezing, extending over a range of temperature, it is not as simple, for the values of the two constants must change with change in temperature. There is ample evidence that the postulated mechanism is correct even though a quantitative derivation of the rate of isothermal or of ordinary freezing in terms of the two constants has been lacking. In recent years other reactions have been found to proceed in a similar fashion. It has been well established, particularly by Bain,2-8 that. the formation of pearlite from the eutectoid decomposition of the solid solu-tion austenite proceeds in such a way, and Polanyi and Schmid, Tammann and Crone, Karnop and Sachs, and others9-11 have shown that the process of recrystallization proceeds in a similar way. Isothermal reaction rates have been determined for eutectoid decom-position by a number of investigators. Bain's2-8 work on the formation of pearlite from austenite is especially valuable in this respect-the type of isothermal reaction curve obtained, as illustrated in Fig. 13, showed an initial slow rate, accelerating to an intermediate maximum rate which then decelerated to the completion of the reaction; similar curves have been obtained by Wever and his collaborators.12 Other eutectoid decompositions show similar behavior: for example, the decomposition of the beta eutectoid in the copper-aluminum system, studied by Smith

Jan 1, 1939

By H. K. Livingston

THE first person to investigate intensively the vast field of surface phenomena and capillary effects was the eminent English scientist, Lord Rayleigh (1842-1919), who laid down most of the fundamentals of this subject. This work was greatly amplified by Irving Langmuir,1 who, in connection with research for the General Electric Co., spent 25 years on the study of the surface chemistry of films, finally receiving the Nobel Prize in Chemistry for 1932 in recognition of his work. At present, William Harkins,2 of the University of Chicago, is the world's foremost authority on surface-tension measurement and his independent work, when combined with that of Langmuir, resulted in the orientation con-cept of solubility and surface activity, which is now an important funda-mental in chemistry. The theory laid down by these men was first applied to practical considerations regarding petroleum reservoirs by F. E. Bartell,3 of the University of Michigan, in connection with an American Petroleum Institute research grant. The latest and most advanced application of Bartell's work is contained in an article published in 1935 by Allen Garrison,4 of Rice Institute, in which he relates Bartell's measurements to the ratio of oil to water produced by wells and shows the types of petroleum reservoirs where the effects studied by Bartell are significant. This article is intended as a minor extension of such work.

Jan 1, 1938

By Carl Henrich

In the winter of 1895 to 1896, during the construction of the Jackson and Cincinnati railroad, running from Addison, Lenawee county, Mich., to Jackson, Mich., in a northerly direction, I had occasion to observe some interesting geological features, described below, in a cut of this railroad made through the low ridge of gravel and sand, dividing the valley of Silver Lake and Silver Creek from the Goose Lake and Goose Creek valley, in Lenawee county. The surface-deposits of this part of the county are, as is well known, of glacial origin. Gently rounded, long ridges of sand, gravel and clay intervene between the marshy bottoms and the lakes of the valleys. The nature of the deposits, varying from a sandy clay or clayey sand to fine and coarse gravel and pure siliceous sand on the one hand, and to a very tough, fine, uniform and often indurated clay on the other, as well as the irregular and sudden changes, sharply divided, between these materials composing the ridges, in the cuts made through them by the railroad, would admit of no doubt that this country owes its present surface-configuration primarily to the action of the last glacial period, which covered its surface with an immense ice-sheet. The well-known ice-markings on the huge granite, schist, greenstone and conglomerate boulders found everywhere imbedded and protruding from the surface, add their testimony to the other characteristics mentioned. Most of the cuts made by the railway through the ridges showed in a marked degree the irregular arrangement and the sudden changes of and between the materials mentioned above. One cut, however, known as Kelly's cut, or Kelly's gravelpit, about 4 1/2 miles north of Addison, and about 1 1/2 miles south

Jan 1, 1897

By Y. Fukunaka, Y. Kondo, Z. Asaki, S. Nakashita

The pyrite smelting process in which about half amount of sulfur is recovered from pyrite by thermal decomposition in an oxygen-free high-temperature combustion gas flow in the flash smelting furnace is being conducted at Kokkola Works in Finland. A mathematical model of this process was developed, and the rates of thermal decomposition and fusion of suspended sulfide particles in the reaction shaft of furnace was calculated. This model is thought to be appropriate because of a fairly good coincidence of the calculated length of reaction zone with the shaft height of the furnace at Kokkola Works. The calculated reaction zone in which the thermal decomposition and fusion of sulfide particles occur becomes longer when pyrite particles of larger sizes are fed. The feeding rate of pyrite particles and the gas velocity at the nozzle exit are also the important operating factors. These two factors are closely related to the volume fraction and the residence time of suspended particles in the gas stream, and the optimal combined levels of these factors at which the length of reaction zone becomes minimal were obtained.

Jan 1, 1976

By T. Leffers, A. Grum-Jensen

The development of texture in copper and brass (15 pct Zn by weight) rolled at room temperature and in copper rolled at -196°C has been followed by determination of pole figures for various degrees of reduction. The concurrent development in microstructure has been investigated by transmission electron microscopy. For low deformations, the texture in brass, and in copper rolled at -196°C, is the same as the texture in copper rolled at room temperature. The difference in texture does not show until 50 pct reduction. At the same reduction at which the difference in texture appears, mechanical twinning starts in brass and low-temperature rolled copper. Nevertheless, Wassermann's twinning theory is found to be incompatible with the present resulls. All fcc metals and alloys develop, by heavy rolling, one or the other of two types of texture, classified for convenience as copper type and brass type, or possibly a '(mixed" texture representing an intermediate stage between the two types. The pure fcc metals, except silver, develop copper-type texture by rolling at room temperature. Silver and many alloys, including brass with more than 10 pct Zn, develop brass-type texture.' By rolling at low temperatures a transition in texture from copper type to brass type has been observed for copper of commercial purity.2'3 It is generally accepted that there is a correlation between the type of texture developed and the stacking fault energy. Metals and alloys having fcc structure develop brass-type texture when rolled at room temperature if the stacking fault energy is low, whereas those with higher stacking fault energies have copper-type texture.2 Thus, the difference in stacking fault energy must cause a difference in deformation mechanism responsible for the difference in texture. Of the numerous theories advanced concerning the nature of this difference in deformation mechanism, four seem to be of current interest. Smallman and Greeen,2 Dillamore and Roberts,4 and Dillamore5 refer to the fact that cross slip more easily takes place in a material with a higher stacking fault energy and suggest that the copper-type texture is developed by deformation with extensive cross slip whereas the brass-type texture is developed by deformation without cross slip. Haessner6 has advanced the theory that the copper-tye texture is developed by a combination of normal {111} slip and slip on other planes, mainly 1100). Thus his theory, like the theory above, proposes an additional deformation mode for the formation of the copper-type texture. Contrary to this, wassermann7 and Ahlborn et al.8 believe that the copper-type texture is obtained by normal slip. In their opinion mechanical twins will change a copper texture into a brass texture. For this reason it is suggested that the brass-type texture is developed when, in addition to normal {111}(110) slip, mechanical twinning is present. None of these theories are, however, supported by direct experimental evidence. In a recent experiment Hu et al.9 have followed the development of rolling texture in copper and brass. The texture of copper and brass was found to be es-

Jan 1, 1969

By T. Saburi, C. M. Wayman

The massive and martensitic transformations in ß Cu-Ga alloys were studied by optical microscopy and by transmission electron microscopy and diffraction. These types of transformation are distinct and do not merge into one another. An internal fine structure due to stacking faults was found in both the massive phase (m) and the martensite, but the origin of the faults is believed to be different in each case. The faults in the martensite are due to the lattice invariant or "second" shear of the phenom-enological theory, while those in the are probably growth faults and deformation faults arising from the transformation volume change. Evidence is presented for ordering in the ß phase prior to transformation into martensite, and the crystal structures of and ß' and ßi martensites are discussed. THE results from some previous investigations1,2 have led to the suggestion that martensitic and massive transformations have certain common characteristics. It presently seems established that massive transformations like martensitic transformations are essentially diffusionless,1,2 but unlike martensitic transformations, when a new phase forms massively there is no shape change or surface relief.= If the massive-type transformation is crystallographically similar to martensitic transformations, one would expect a fine structure as a result of the lattice invariant shear4 which is a part of the transformation mechanism. The existence of such a fine structure (i.e., slip, twinning, or faulting), if any, can be verified by transmission electron microscopy, and thus the present investigation was undertaken to compare the internal structure of massively and martensitically formed phases in Cu-Ga alloys which were derived from a parent of the same composition. The transformation characteristics of ß Cu-Ga alloys were also studied. The bcc ß phase in the Cu-Ga system, Fig. 1, is stable above 616oc.' Depending upon the cooling rate, ß Cu-Ga alloys can undergo three different types of phase transformations. The ß phase of eutectoid composition (23.7 at. pct Ga) decomposes into the ? phase (hcp) and the phase (complex cubic) by means of a eutectoid reaction. When the cooling rate is increased so that the decomposition of 0 into [ and ? is suppressed, the ß phase transforms into a nonequilibrium hcp phase, herein denoted ?m by a process of very rapid growth called a "massive" transformation. At even faster quenching rates the massive transformation can be suppressed and the ß transforms martensitically. Massive transformations, apparently similar to those in the Cu-Ga system, have also been studied in the Cu-Zn2,6-8 and Ag-Cd systems.9 Definitive characteristics if the Massive Transformations in 0 Cu-Ga Alloys1 1) The most remarkable feature of the massive transformation in Cu-Ga is that there is no bulk composition change on transformation. According to Massalski,1 the resulting [, phase is a supersaturated extension of the equilibrium [ phase. The lattice parameters continue the trend exhibited

Jan 1, 1965

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By Richard Moldenke

Note.—At the request of the American Society for Testing Materials, this paper wau presented at the New York Meeting, February, 1923, in connection with the "A. S. T. M. Tentative Specifications for Foundry Pig Iron" and The Physics of Cast Iron and Its Bearing on All Cast-iron Products and Specifications for Cast Iron," by William R. Webster. The discussion of this paper was not published by the Institute, having been referred to the American Society for Testing Materials, as these papers were again presented for discussion at the meeting of that Society at Atlantic Cit;, June, 1923. The result of these discussions is shown in the following abstract from the Committee A3 report on cast-iron specifications: During the past year, the adaptability of the tentative specifications for pig iron for the steel and the malleable foundry, in addition to the iron foundry proper, have been studied and suitable changes and rearrangements are being made which appear to cover the situation properly. In spite of the experience of foundrymen to the contrary, there is a persistent call from consumers of castinga for defixute compositions for given lines of castings. To respond to this call for information desired by the consumer—information every modern foundryman should have and guide his procedure with—the committee has requested the Sub-committee on General Cast!rigs to take up this matter with a view of constructing tables of analyses rang? for Important lines of foundry product. These analyses ranges however, are to be given as "recommendgd practice" and not intended for actual spkcification. In this way, the consumer of the foundry product will get the information he wants; the furnace-man will be gulded in the production of his pig irons to prepare for analyses ranges which are more closely standardized and have less of "freak" requirements made by Inexperienced metallurgists; and the foundryman will not be bound by chemical requirements he knows will not work out well with his particular reglonal supphes of melting stock. Doctor Moldenke's paper is published in full as it shows clearly the good results of the Institute's work in 1895 and a comparison of the same with the present knowledge of the metallurgy of cast iron—Bradley Stoughton, Chairman, Iron and Steel Committee. In MaRch, 1895, William R. Webster contributed a carefully prepared scheme for the study of the physics of cast iron to the American Institute of Mining Engineers at its Florida meeting. This summary of the interrelation of the chemical and physical characteristics of cast iron with the operations of daily foundry practice caused a wide discussion of the then little understood though universally used material. Mr. Webster has requested the author to bring the subject up to date and, while glad to comply, he must pay that with all the knowledge that has been gained in the quarter century that has passed since the subject was brought to the attention of the Institute—and we now are pretty familiar with cast iron in all its aspects—there is practically noth-

Jan 1, 1923

By R. W. Fountain, M. Korchynsky

The precipitation phenomena occurring in cobalt-tantalum alloys have been investigated in the temperature range frm 500" to 1050°C by correlating the results of metallographic, X-ray, micro-and macrohardness, and electrical resistivity studies. The property andmacrohardness,changes were found to depend on 1) general precipitation, and 2) lamellar precipitation. Two new intermetallic phases have been identified: 1) a Co3Ta, a metastable ordered face-centered-cubic compound, and 2) a stable ß Co3Ta phase of hexagonal structure. In addition, the previously reported Co2Ta phase was found to exist in two allotropic modifications: the hexagonal MgZn,-type and the cubic MgCu2-type Laves phases. SINCE a large variety of structures can result as a consequence of the decomposition of a solid solution, predictions on the nature of property changes are difficult, if not impossible, to make. For any rational attempt to correlate properties and structures of a precipitation-hardenable alloy, a detailed understanding of the kinetics of decomposition and morphology of phase separation, as well as knowledge of phase relationships, appears to be prerequisite. Information of this type has been accumulated in the past for many alloy systems, both of theoretical and pastforpractical importance.1,2 Although the presence of intermetallic compounds has been reported in cobalt-base alloys,3 the amount of published information on precipitation-hardenable cobalt-base systems is very limited. A survey of the binary phase diagrams of cobalt indicates that cobalt-tantalum alloys might be of interest as typical of other cobalt-base systems in which Laves phases of the A,B type can be precipitated from solid solution. The present work has been undertaken, therefore, to study the kinetics and morphology of the precipitation reaction in this system and to establish a base for a correlation between the structural aspects and properties in this class of alloys. PREVIOUS WORK The only available phase diagram of the cobalt-tantalum system is based on the work of Koster and Mulfinger. According to these authors, the maximum solubility of tantalum in cobalt is about 13 pct (at 1275°C) and. less than 7 pct at room temperature. Tantalum additions lower the temperature of allotropic transformation of cobalt (about 420°C), and at 7 pct Ta, the high-temperature face-centered-cubic modification (ß cobalt) is retained at room temperature. The precipitating phase was originally designated as Co5Ta2 compound (55.2 pct Ta, about 1550°C melting point), but subsequent investigations by wallbaum5" identified this constituent as the A,B-type Laves phase. Wallbaum's data indicate that there are two modifications of this intermetallic compound: one richer in cobalt (Co2.2 Tao.8)of the hexagonal MgNi, type; and another of a higher tantalum content (Co2Ta) of the cubic MgCu, type. On the other hand, Elliott7 found that the cobalt-rich alloy (CO2.10,Tao.~l) was predominantly the cubic MgCu, type at 800°C and a mixture of both the MgCu2 and the hexagonal MgZn,-type Laves phases at 1000°C. At 1200°C, Elliott found only the MgZn, type while at 1400°C, he observed only the MgCu2 type. At the stoichiometric composition, Co2Ta, Elliott reported only the cubic MgCu2-type Laves phase in the temperature range of 600oto 1600°C. The precipitation of the cobalt-tantalum intermetallic compound is accompanied by a marked increase in hardness. According to Koster's4 data, the Brinell hardness of an 8 pct Ta-Co alloy increases from 230 to 340 upon short-time aging at 800°C. EXPERIMENTAL PROCEDURE The binary cobalt-tantalum alloys investigated contained 5, 10, and 15 pct Ta. The range of tantalum additions was thus slightly broader than the reported minimum and maximum solid solubility limits of tantalum in cobalt (7 and 13 pct, respectively)4 The alloys were vacuum-induction melted in a magnesia crucible using cobalt rondelles and technically pure tantalum sheet as raw materials. Deoxidation of the melt was accomplished with carbon, and the chemical analysis of the alloys is given in Table I. The effect of isothermal aging treatments on the progress of precipitation was studied on samples cut from cast ingots. These samples were solution treated for 2 hr at 1250°C and water-quenched. Aging was conducted in the temperature range from 500" to 1050°C for periods between 15 min and 1000 hr and followed by water-quenching. To prevent contamination from the atmosphere, all samples were sealed in evacuated Vycor or quartz tubes for heat-treatments. For solution treatment, argon at 0.2 atmospheric pressure was introduced prior to sealing of the capsule to prevent collapse at high temperature, and titanium sponge was placed at one end of the capsule to act as a getter. MACROHARDNESS The effect of aging on Vickers hardness (Dph) of

Jan 1, 1960

By Harvey Cline, Donald P. Ferriss

THE violent outgassing of commercial tungsten and other refractory metals when melted in an electron beam zone refining apparatus1"3 is dealt with experimentally by one or both of two approaches. One is to provide a suitable emission current control1,2 the other is to purify the metal in the solid state before melting.4 The first of these is usually sufficient, but the authors chose also to investigate the source of the troublesome gases and to devise means of solid-state purification. Some further insights into the use of tungsten as a structural material at temperatures near its melting point were also revealed in the course of the work. One may speculate on the causes of gas formation in tungsten at high temperature by inferences from the literature and an examination of the impurities in commercial wire. Davenport5 observed microporosity in both tungsten and molybdenum filaments heated to several hundred degrees below their melting points. Studying the function of oxygen in molybdenum welds, Perry, Spacil, and wulff8 attributed similar porosity to the disproportionation of Moo2 to molybdenum metal and Moo3. Tungsten dioxide also disproportionates7 above 2000oC to yield WO3 vapor at considerable pressure. Commercial tungsten contains some 5 to 20 wt ppm O and a similar concentration of carbon depending on the details and precautions of processing. Therefore, evolution of CO is also a strong possibility as a source of gas at high temperatures. Furthermore, even for activities in the order of 0.01, it may be calculated that the pressure of CO at 3000°C would be over 4000 psi, which is in excess of the tensile strength of tungsten at this temperature.9,10 Powder metallurgy tungsten contains some 0.02 pet Fe and 0.002 to 0.005 pet of the elements Ni, Si, Al, Ca, Mn, Mg, and Mo; at temperatures over 2800°c, therefore, these elements will exhibit appreciable vapor pressure, though small compared to that of WO3 and CO. Some of these impurities may react to form high-pressure monoxides such as SiO and A10. Finally, dissolved and occluded nitrogen is an ever-present source of high-pressure gas. Commercial Type 218, General Electric filament wires, 0.025 in. diam, were heated by resistance in 10 -4 mm of Hg and in argon or hydrogen at pressures from 50 µ to atmospheric. For temperature determinations in vacuo, the Jones - Langmuir8 current-temperature relationship was employed. For gaseous atmospheres, the burn-out temperature was assumed to be the same as in vacuo so that a small, constant correction could be made for temperatures below burn-out conditions (i.e., local heating to failure). Several dozen experiments may be summarized by pointing out some structural observations. At 3050oC in 1 atm of A, porosity is very evident after 30 min, as shown in Fig. 1. For the section in Fig. 2, failure occurred 200°C below the melting point and many voids have grown in the grain bound-

Jan 1, 1962

By D. J. Carney, E. C. Rudolphy

Large macroscopic nonmetallic inclusions were related to altered fireclay refractories by chemical and microscopic means. Pouring refractories are discussed as a source of these large inclusions. Nozzles and wells are major contributors. Use of alkali and titania contents as tracers is described. Recommendations are offered to minimize the sources of inclusions from pouring refractories. IN any attempt to improve the cleanliness of plain carbon and alloy steels, consideration must be given not only to the proper deoxidation practice to minimize inclusions, but also to sources of inclusions from pouring refractories. In some cases, the inclusions resulting from deoxidation may be minor in amount, yet a relatively dirty steel may be produced as a result of improper care in the pouring practices for the steel. The number of studies of inclusions resulting from pouring refractories has increased recently and some excellent reports on this subject have already been published.'4 Some of these reports were reviewed briefly in a companion paper by M. P. Fedock.5 Mr. Fedock's contribution is a fine addition to the studies necessary to improve steel cleanliness for the ultimate benefit of all steel producers and consumers. In the interest of constantly improving cleanliness, the authors have been actively engaged for the past two years in experimentation to determine more closely the sources of inclusions in steel. One phase of this work was associated with efforts to define more closely the sources of macroscopic inclusions which have been experienced on occasional heats. The term "macroscopic inclusions" is defined in general as those inclusions which are visible to the naked eye or at low magnifications of the order of less than X25. These inclusions sometimes can be seen in the macro-etch tests of billets and slabs. This report summarizes a few of the field experiments and laboratory studies conducted at the South Works of the United States Steel Corp., which were made regarding nozzles, wells, and ingot scums, as well as inclusions occurring in steel products. The data in the present study, together with the data of Mr. Fedock concerning ladle erosion, should be of value in regard to future studies of inclusions arising from pouring refractories. The knowledge gained as a result of data collected thus far at South Works has been helpful in improving the cleanliness of the products and in pointing the way toward further improvements. Similarity of Large Inclusions to Refractories and Altered Refractories In the routine inspection of billet etch tests, occasional inclusions visible to the naked eye have been observed. These large inclusions most frequently occur near the top of the ingot and near the billet surface. When such material was encountered, careful examinations were made in an attempt to determine the origin of these inclusions. In a relatively few cases, examination revealed that the material was unaltered fireclay refractory of a type similar to that used for hot-top material, with only the surface of the inclusions having an altered appearance under the microscope. However, the great majority of these inclusions were completely altered-refractory material. The term "altered refractory" is defined

Jan 1, 1955

By Percival Roberts

It may seem necessary to offer an apology for presenting for consideration a process which is conspicuous by its absence in the literature of the Institute, and which may be thought by some to belong to the past in metallurgy, and to have been already superseded. But the large capital invested in puddling calls for a careful consideration of the question whether the time has certainly arrived when the puddling furnace must be replaced by the converter and open-hearth furnace. May there not still be a place for puddled iron alongside of molten iron and steel, and is not the improvement of the puddling process itself worthy the attention of engineers equally with the Bessemer and open-hearth processes? The changes involved in the conversion of pig iron into wrought iron are well understood and need only be briefly alluded to. The patent of Henry Cort bears the date of 1784. Since that time * the improvements in the process have mainly consisted in the replacement of sand by iron bottoms by Samuel Baldwyn Rogers in 1818, and the still more recent substitution of iron oxide for the refractory materials used for the rides and bridge of the hearth, which distinguishes the wet or boiling process from the dry or pnddling process. Chemically, the process consists in the removal of the metalloids from the pig iron, a result effected mainly by the iron oxide. Silicon is first oxidized, then the phosphorus, and finally the carbon. The silicic and phosphoric acids produced pass into the cinder and the carbonic oxide burns as it escapes from the bath of metal. It is interesting in this connection to note the effect of temperature on the removal of the phosphorus from the iron. As is well known, no phosphorus is eliminated under the oxidizing influences prevailing in the Bessemer converter, while from 70 to 80 per cent. is removed in puddling. But we find, if in working cold short irons

Jan 1, 1880

By B. Amadei

INTRODUCTION Laboratory studies on the deformability and strength of intact rocks generally involve the uniaxial compression test, the standard triaxial compression test and direct or indirect tension tests. If [al ,a2 ,a3] are principal stresses [(al>a2>a3)] with compression taken as positive and tension taken as negative, the applied stress field for each one of these tests can be represented as shown in Fig. 1. However, for most in-situ conditions, such as those that exist at any point around an underground excavation, the stress field is truly three-dimensional or multiaxial [(al+ a2+a3)] and none of the tests shown in Fig. 1 can be used to predict the mechanical behavior of the rock. There are special cases for which one of the three principal stresses vanishes. Biaxial loading of rocks in-situ takes place, for instance, when rocks deform and fail in plane stress conditions. This can occur in a free unloaded surface of a rock structure such as in the wall of an underground excavation or a rock slope. Parallel to the free surface, the stress field components can be both compressive [(al>a2>0)], both tensile [(O>a2>a3)], or mixed, one component being compressive and the other one tensile [(U~>O>U~)]. The purpose of this paper is to present the results of 25 true biaxial tests that have been conducted on cubical specimens of Indiana Limestone using the multiaxial cell available at the University of Colorado at Boulder. The tests include uniaxial compression and tension, biaxial compression and combined biaxil compression- tension. Flexible fluid cushions and brush bearing platens were used for compressive and tensile loading respectively in order to minimize loading end effects on the test specimens. The paper begins with a review of previous investigations on the multiaxial behavior of rock. Then, test results are presented in terms of

Jan 1, 1984

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,' the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"' and the

Jan 1, 1946

By Gifford E. White

Explanations of the basic procedure for making earth-conductivity studies by the Eltran method have already appeared in several placeS. 1,2,3 In its essentials, this method consists of applying step functions of voltage to one pair of earth grounds and measuring the transient potential resulting at a separate pair of ground points. As previously pointed out,' the transient potential resulting from a suddenly applied steady voltage is the indicia1 transfer function of Carson1 6 which has been extensively studied in network theory. The discussion here, with one special exception, will ignore the problem of how the physical configuration of the earth affects the transient response voltage; it appears that this phase of the problem has been solved in only a few special cases having any direct bearing on the prospecting problem. Entirely distinct from the potential-theory aspect of the conductivity problem is the interesting material that can be had from studying the well-known network relations between cause and effect in linear circuits, and thus deducing criteria for the application of the several experimental methods available. To do this, only one assumption need be made about the nature of the earth. The earth is to be considered a linear conductor within the tolerance of ordinary measurements. The discussion will be restricted to collinear electrode configuration like that of Fig. I, since this is the only type of spread practical for use with driving currents that vary with time. Here one pair of grounds carries the driving current, and in line with these and external to them is a RECORDING Fair of potential probes. The problem will be to consider the relation between the different voltages appearing between the potential circuit terminals when various types of driving voltage sources are inserted in the current circuit. Suppose that the grounding points G, and G2 make good contact with the earth, and that a battery of sufficient voltage to produce one ampere of direct current is introduced into the current circuit by the closing of a switch. The potential transient response to such a voltage can be measured by taking an oscillogram at the potential Directors terminals, giving the time function that has been called A(l).4 This time function has been solved for analytically in the case of a homogeneous earth,"' and the

Jan 1, 1946