Search Documents

By I Doye

Acid mine drainage is a serious environmental problem caused by the oxidation of sulfide minerals responsible for highly acidic, sulfate and metals-rich drainage. Several methods of mine waste management have been developed that reduce liabilities on environment. Layered co-mingling of waste rock with compacted tailings, covers with capillary barriers effect, and co-disposal of waste rock and tailings are these new methods which are used to reduce the formation of acid mine drainage. These methods shield waste rock dumps from oxygen. These techniques could prevent oxidation reaction. In this study, alkaline industrial wastes are used with acid generating tailings to inhibit acid mine drainage. The alkaline wastes selected are cement kiln dust (CKD) and red mud bauxite (RMB). These alkaline materials are used to keep neutral conditions in the fine material layer and to inhibit the metabolic activity of Thiobacillus ferroxidans which catalyses the oxidation of sulfide minerals. A series of timed static leaching tests were performed by reacting samples of mine tailings with two, five and ten per cent alkaline material in order to characterise geochemical balance between liquid and solid phases. Column tests have been set up with oxidised tailings, waste rock, CKD, and RMB. Column tests have been carried out to simulate layered co-mingling, covers, liners, and co-disposal of waste rock and tailings. Column leach tests were conducted in order to investigate the long-term neutralisation potential of alkaline materials and the drainage water quality. Bacteria counting were performed on each sample after testing. The results obtained show that the addition of alkaline materials permit the retention of near neutral conditions in the fine material layer, thus increasing water quality and preventing bacteria development. In fact, the pH results show that the use of five per cent, ten per cent CKD or ten per cent of a mixture of CKD and RMB permit the retention of neutral pH conditions in the reactive layer. At these percent rates, the concentrations of Al, Fe, Cu, Zn, and SO4 in solution are significantly reduced compared to those obtained with the tailings only. In presence of waste rock, the relative position of the fine material layer is important. When the fine material layer overlaying reactive waste rock is composted of reactive tailings with ten per cent CKD and ten per cent (CKD:RMB), a delay was observed before achievement of near neutral pH. The neutral pH conditions remain stable over time. The mixture of CKD and RMB provides a better short-term neutralisation than the use of CKD alone. The use of alkaline materials is beneficial in order to reduce the concentrations of Fe and other metals such as Cu and Zn as well as the number of viable bacteria. The use of ten per cent RMB alone does not involve the neutralisation of reactive tailings. In the cases where the fine-grained layer are below or mixed with the waste rocks, the near neutral pH values are directly reached with ten per cent CKD. However, the pH values decrease rapidly and the number of viable bacteria increases.

Jan 1, 2003

By E Philippa, J Vitanza, C Hawtin, B Miller

B Miller , E Philippa , C Hawtin and J Vitanza

Mar 22, 2022

This paper details successful implementation of a revolutionary pit access system involving excavation of an 'in-the-wall' ramp at Three Mile Hill open pit operated by Gold Mines of Coolgardie, formerly Goldfan Limited, at Coolgardie, Western Australia. Three Mile Hill is a medium-size, open pit, gold operation typified by hard, competent, fresh rock conditions from near surface. The project involved construction of a haulage tunnel or decline access located in the wall of an open pit in place of a conventional pit access ramp. Works undertaken as discussed herein included excavation, support, ventilation, dewatering, services installation, commissioning and monitoring. Prior to implementation, the conventional hardrock pit slopes and designs were constrained by the presence of infrastructure and a main road to the North and by adjoining leases to the Southeast. The combination of these factors and economic considerations resulted in a decision to proceed with an innovative in-the-wall ramp access system that is believed to be the first of its type in Australia. Back-analysis indicates that implementation resulted in a cost saving of as much as A$3.6 million and increased mineable pit reserves. The paper deals with the successful implementation and operation of the in-the-wall ramp haulage as well as an economic evaluation that is aimed at drawing some general conclusions on favourable conditions for implementation in other mining scenarios.

Jan 1, 1996

By K S. Smith, B P. Jackson, P J. Lamothe

The upper Arkansas River south of Leadville, Colorado, USA, contains deposits of fluvial tailings from historical mining operations in the Leadville area. These deposits are possible non-point sources of acid and metal contamination to surface- and ground-water systems. We used stable-metal isotopes to help ascertain metal retention and release mechanisms that influence metal transport from the deposits to shallow ground-water systems. To accomplish this, we excavated an intact core from a small fluvial tailings deposit and performed laboratory column experiments to examine the amount of metals leaching through the core. Deionised water was continuously applied to the top of the core, and effluent was collected from the bottom of the core for a period of about two months. Three saturation conditions were used, including unsaturated, partially saturated, and fully saturated. Reducing conditions developed upon partial and complete saturation of the core. During the unsaturated leaching phase, core effluents were acidic (pH 2.8 - 3.5) and contained elevated metal concentrations. During a portion of the unsaturated leaching phase, stable-metal isotope spikes and conservative tracers were simultaneously applied to the top of the core. The isotopes provide a means to delineate metal behaviour within the core. During the unsaturated leaching phase, the isotope spikes did not exhibit breakthrough with simultaneously added conservative tracers. However, some of the stable-metal isotope spikes did break through when reducing conditions occurred in the core (during the partial- and completesaturation conditions). In this paper, we use Cd as an example of the utility of stable-metal isotopes in geochemical studies. In the case of Cd, after the core was partially saturated, the 111Cd spike was released as evidenced by a change in the Cd isotope ratios in the effluent. This release continued during the fully saturated leaching phase, however, the total Cd concentration did not increase. These results suggest that the 111Cd spike was retained inside the core during the unsaturated leaching phase, and only partially released as reducing conditions developed. Results from this core-leaching experiment indicate there is a large reservoir of water-soluble material within the fluvial tailings deposit, which yields elevated metal concentrations and high acidity, and which may degrade adjacent ground- and surface-water quality. Use of stable metal isotopes in this study facilitated the determination of different metal-retention processes, metal-release processes, and metal sources in the fluvial tailings deposit in response to changing geochemical conditions.

Jan 1, 2003

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By C Delwig

ThyssenKrupp specialises in the manufacture of high-grade steel-sheet products. Its main customers include the automotive, construction, household appliance, energy and packaging industries.At its works in Duisburg, Germany, ThyssenKrupp Steel Europe produces 12 Mt of crude steel annually, making Duisburg one of the world’s largest steel hubs.ThyssenKrupp have installed an online elemental analyser and limestone dosing control System on one of three Sinter strands at Duisburg in an attempt to control the sinter raw mix with better precision. Traditionally, set point changes to the raw mixture were made after sampling and laboratory analysis of the sinter product. The analyser chosen uses prompt gamma neutron activation analysis to determine the elemental content of moving material on a conveyor each minute and was supplied by Thermo Fisher Scientific. The project goal was to control the CaO/SiO2 ratio (basicity) and reduce its variability in the sinter feed.Evaluation of the system has shown that the addition of the online analyser reduces the time lag related to the former method, therefore upset conditions can be reacted more quickly by the control system, and this has resulted in a more stable sintering process. As a result, the sinter feed variability in case of the basicity has been reduced by half. While CaO/SiO2 control was the initial aim of the project, a number of other benefi ts have been realised, such as a reduction in return fi nes and a financial benefi t of 0.11 €/ton of sinter attributed to the reduction of coke breeze and limestone. ThyssenKrupp Steel Europe has identifi ed that additional information available from the analyser could be used to optimise the complete sinter process.The project was carried out with a financial grant of the research program of the ‘Research Fund for Coal and Steel’.

Jul 11, 2011

By A Roseman, T Gruber

Traditional methods for installing gaskets for segmented bored tunnels have relied upon different bonding procedures with adhesives that carry a series of disadvantages to segment producers. Fixation of the gaskets into the concrete segment as part of the casting procedure has been developed over the last 20 years and has emerged as an economical solution to produce high-quality tunnel segments for various technical tunnel applications. This paper investigates the advantages of using anchored gaskets, the different tunnel systems that employ anchor gaskets and reviews the first anchor gasket project; the Lee Tunnel and analyses how segment production efficiencies are gained.CITATION:Gruber, T and Roseman, A, 2014. Use of anchored gaskets in segmented bored tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 253–256 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Wylie A. W, Mathew P. J, Eisler P. L

Field studies of the radiations backscattered by iron ores from a 60Co source of primary gamma radiation located in a borehole logging probe have confirmed thatthe P" factor, a ratio of high energy gamma ray intensities to low energy intensities in selected energy windows of the backscattered gamma-ray spectrum, is a valuable measure of grade for sedimentary iron ores of the Pilbararegion of Western Australia.Laboratory studies of model boreholes have shown that variations in borehole diameter and variations in bulk density of the formations have a significant influence on the measurement of P" ratios. If these influences 'are taken into account the mean ore grade in a new blast hole, for instance, can be predicted with a probe of suitable configuration to within 0·8 per cent Fe at the 95 per cent confidence level, while the grade of a single 120-cm split can be determined to within 2·6 per cent Fe. These results were obtained by pooling data from five blast holes covering the range of iron concentrations 20-68 per cent Fe and apply to the mean hole grades 54-68 per cent Fe.Results for two development holes were generally comparable to those obtained from individual blast holes95 per cent confidence limits of ±0·9 per cent Fe for mean ore grade and ± 4·1 per cent Fe for single splits. A greater number of data points is needed before these confidence limits can be further improved.The technique utilized to obtain these results was derived from a "multiband" approach to collection of backscattered spectral intensity data, an approach which permitted selection at the data processing stage of the most statistically significant P" ratios for the type of mineralization encountered in the field. The multiband technique also permitted selection of the most significant of another set of windows in the backscattered gammarayspectrum to measure a newly developed "S-factor", a ratio sensitive to borehole diameter. Another window provided information on bulk density. All these measurements were made with a single pass of the same loggingprobe.

Jan 1, 1977

By Spencer P. A

Bacterial oxidation, previously known as bacterial leaching or bio-leaching, has been applied at laboratory and pilot plant scale to many refractory ores and concentrates around the world. The most common bacterial culture used in this process has been Thiobacillus sp. This organism is limited in commercial application, especially in Australia for several reasons. The optimum operating temperature range for this culture is 30¦C to 40¦C and high levels of some metals such as arsenic, silver, and copper have toxic effects on the culture thus reducing its effectiveness. The culture employed by BacTech (Australia) Pty lid is a moderately thermophilic culture which operates in a temperature range of 40¦C to 55¦C (which is more amenable to the Australian climate) and with higher resistance levels to metals often found to be toxic to Thiobacillus sp..

Jan 1, 1991

Both blast furnace and steel furnace slags have been used extensively and successfully on main line railroads in the United States for more than 25 years. Annually, these slags are being used as ballast at the rate of about 4 million tonnes of blast furnace slag and 1 mil- lion tonnes of steel furnace slag, much of it on main line with 90 metric tonne car loadings. More steel furnace slag would be used if it was available. Both slags meet all the specification limits of the American Railway Engineering Association. Actual use on high density rail- roads has confirmed the long range economics of their use. Comparison of laboratory tests, such as Los Angeles abrasion, with actual field per- formance has shown conclusively that commonly used laboratory tests can not be used to accu- rately compare the quality of various types of ballast materials.

Jan 1, 1979

By Rashchenko AF, Voiloshnikov GI, Elshin VV, Khomutov VV

The sorption method for the precious metals recovery fromsolutions and pulps are a perspective trend of modernhydrometallurgy. Russian gold mining industry uses thesemethods, anion-exchange resins being applied as sorbents. Theanion exchange resins allow effective recovery of preciousmetals, however, they have several drawbacks as compared withactivated carbons: high cost of sorbents; difficulties arisingduring treatment of pulps with complex ion composition;necessity of using titanic equipment and thiourea for gold elutionfrom loaded anion-exchange resin and its regeneration.

Jan 1, 1993

As Project Managers for the Blair Athol Coal Mine Project, CMPS selected a number of computer systems to assist in project control. The areas where computers were used were: 1) Planning & Scheduling 2) Procurement Reporting 3) Document Control 4) Accounting 5) Cost Control 6) Control of project management and engineering manhours The computer packages selected were generally effective in their own areas. During 1982, CMPS acquired an in-house project control package called GC/Cue. Project control systems for the project are progressively being set up on this system. The advantages of this type of system are: 1) Improved accessibility of information, due to on-line operation and the use of VDU's. 2) Improved turn around time for computer runs and production of reports. 3) Improved presentation and format of reports. 4) Lower costs.

Jan 1, 1983

Contract mining is an integral part of the underground and surface hard rock mining industry in all states of Australia. Contract mining is now makes a major contribution to the opencui coal industry in Queensland and New South Wales with Thiess alone producing over 16 million tonnes per annum with safety performances that most coal companies would be proud of. Contract mining is now attracting interest in the underground coal sector.

Jan 1, 1998

Draglines have been a significant part of world open cut mining since the early part of the 20th century particularly for the removal of overburden in the strip mining of coal. Since the mid-1960s draglines have played a major part in the large strip mining coal developments of Queensland and New South Wales.There are now over 60 large draglines operating in Australia ranging in size from 23 to 103 cubic metres bucket capacity, with digging depths to 60 metres, dumping heights to 50 metres and dumping radii to 100 metres. The application of these draglines has progressed through the uncovering of coal in shallow, single seam operations to deep multi-seam operations requiring a greater dependence on pre-stripping activities ahead of the dragline to remove overburden not able to be efficiently handled by the dragline.

Jan 1, 1992

By D Woolmer

Since January 2019, BHP Olympic Dam have been trialling the use of a drone based LiDAR mapping system for the purpose for surveying stope voids. This new technology utilises Simultaneous Location and Mapping (SLAM) algorithm providing positioning, stability and collision avoidance in GPS denied environments. Implementation of this system utilised underground personnel trained in the equipment’s use. The study’s intention was to evaluate the effectiveness of this equipment versus traditional surveying methods in regards to quality, safety and productivity. The trial results showed a marked improvement in the quality, productivity and personnel safety when conducting surveys. The use of the drone and LiDAR system reduced personnel and equipment requirements for surveys, thus allowing these resources to be deployed elsewhere. The technology’s simple and rapid deployment allowed multiple surveys to be conducted during a 12 hour shift, including ad-hoc work with minimal disruption to underground operations. After the drone’s initial trial, further work was conducted to utilise the Hovermap LiDAR scanner on other platforms to increase utilisation. A mounting system was created allowing the LiDAR to be mounted on a remotely operated loader or vehicle. This enabled drawpoint scans to be taken directly after production completion, resulting in faster stope close outs and drive scans for convergence monitoring. Implementation of the LiDAR system has resulted in improvements in the stope production cycle by reducing delays previously associated with data capture. The increase in the volume and quality of data has also allowed in-depth back-analysis of stopes in new mining areas to be conducted, which have driven improvements in the design process.

Mar 15, 2021

By C Glassock, P Bodon, M Elias

Computer simulation is a well-accepted tool for modelling the behaviour of large or complex operating systems. Less common is the use of simulation as a design aid, but FluorÆs simulation group regularly applies discrete and continuous simulation models to assist with optimisation and risk management in a wide variety of mining, mineral processing and logistics applications. To demonstrate the wide applicability of simulation modelling as a design aid, this paper describes three case examples from FluorÆs recent work that cover both discrete and continuous operations.

Jan 1, 2003

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2007

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By P S. Datta, V N. Misra

Higher bed height up to 680 mm, including 30 mm hearth layer of sized return sinter and high suction below the grate bars up to 1400 mm WG have resulted in increasing the productivity to a level of 33 t/m2/day and reduced coke rate to a level of 46 kg/tonne sinter. The ferro-wastes like blue dust, flue dust, mill scale, collection from dust catcher and gas cleaning plant, etc have been successfully added in charge mix to produce quality sinters. In this paper, brief description of the work done at Regional Research Laboratory (CSIR) in last few years and two case studies are discussed including the successful development of pan sintering units.

Jan 1, 2002

By S Ramsay, D Povey

This paper presents recent case study data collected by field portable x-ray fluorescence spectrum analysers (FPXRF) as part of grade control activities at three separate (nickel, copper and copper/gold) mining operations. FPXRF has been under utilised for grade control in recent years, largely because the success of early versions of FPXRF was limited to a few metals (eg tin). Efforts to utilise these early versions for other metals was largely unsuccessful and created a perception that FPXRF could not be utilised more broadly within the mining sector and specifically the area of grade control. The structural setting of the analytical function within mining operations has also contributed to the under utilisation of more recent FPXRF instrumentation. The concept of FPXRF as a grade control tool straddles the boundaries of the geology and laboratory departments. As such, this option is often not considered as part of an assessment of grade control procedures for new and existing mining operations. This paper assesses data collected by Australian and New Caledonian miners using FPXRF technology as part of the grade control function and concludes that FPXRF can provide operational and cost benefits to certain mining operations.

Jan 1, 2003