Search Documents

By Bain J. H

Since zinc was first deposited at Risdon in February, 1917, provision of the most economical cathode assembly has been a subject of extensive research, the major problems being corrosion and efficient use of power.From the corrosion viewpoint, a perfect cathode is one in which the life of the headbar and the deposition sheet are the same. However, corrosion usually concentrates in a narrow zone across the face- of the sheet, resulting in breakages which, before the advent of argon arc welding, meant a loss of a 'complete assembly.Attempts to extend sheet life included use of thicker sheets, multitudinous protective coatings applied with varying degrees of success, re-rolling, and for a time, aluminium consumption was reduced when broken sheets found re-use as protecting strips. This latter economy became impracticable when electrode spacing was reduced for greater efficiency in power utilization.As an integral part of the electrode, the headbar was modified accordingly. Copper headbars, although more corrosion resistant, were replaced by aluminium due to a possibility of dissolved, copper promoting deterioration.Thicker electrodes and regulated spacing reduced internal shorting, whilst provision of knife-edge type supports on both contact and insulator ends of headbars aided in electrode centralising and continuous electrical conduction.After much experimeIitation, an assembly has been evolved which, with the aid of argon arc welding and tbe use of minimum additional aluminium, permits comparable headbar and sheet lives, combined with good electrical conduction throughout the life of the cathode.INTRODUCTION Over 300 tons of zinc are produced daily at Risdon from a purified zinc sulphate solution by electrolysis, the zinc being deposited upon all-aluminium (except for copper contact) cathodes. It is stripped in 72-hour cycles from the cathodes, melted and cast into the customary rectangular slabs.

Jan 1, 1958

By Weatherhead J, Grounds J

The Nabarlek Uranium Project located in Arnhem Land in the Northern Territory of Australia was a small high-grade deposit which was the first uranium mine brought into operation following the extensive Commissioner Fox Inquiries into uranium mining during the late 1970s. The operation is almost complete and decommissioning plans have been prepared. This paper reviews all phases of the water management and tailings disposal for the project and compares results with design predictions.

Jan 1, 1988

By M Salu, G J. Kay

"As underground mines increasingly face the challenge of maximising production without losingfocus on safety excellence, the ability to predict the eff ectiveness of mine seals and stoppings andthe identifi cation of defects plays an increasingly important role in mine ventilation management.While technologies for sample testing installed seals provides signifi cant assurance, the difficulty of conducting tests in operational environments, combined with the production impact of destructive testing procedures, has led to the development of a new method for non-destructively testing ventilation control devices (VCDs). This paper addresses the challenges of in situ testing and reviews the approaches previously employed to verify the quality of VCD installations. It then describes a new testing methodology jointly developed by Whitfield Minerals PTY Ltd and Parsons Brinckerhoff (PB) and the range of tests that have been carried out in the laboratory, above ground, at trial underground sites and in active coal mine operations. Although this is a new approach to testing underground VCDs, the method employs recognised testing equipment in a new application. The aim of the new non-destructive technology is to not only verify the thicknessand therefore overpressure rating compliance, of new VCDs, but to allow mine operations t oidentify and locate defects in installed VCDs without causing damage to the material structure.Currently it is difficult, time-consuming and costly to carry out physical sampling and testing ofevery VCD. Therefore, a reliable and accurate means of non-destructively testing concrete andplaster seals in situ will provide substantial operational and safety benefi ts to the underground coal mining industry."

Jun 1, 2012

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

Traditionally trucks have dominated haulage in open pit mines. Only recently have conveyors begun to be used in the long haul and high lift duties of surface mines. Steep angle conveyors are proven versatile systems for elevating or lowering materials continuously at steep angles to 90¦. This paper describes the design of a bucket-type steep angle conveyor that was developed as a joint research project between the Western Australian School of Mines and the Maanshan Institute of Mining Research in China. The steep angle conveyor can be used as a viable option for transporting blocky ore from open pit mines. A pilot conveyor was constructed and tested to determine its technical and operational feasibility. Furthermore, a computer model based on Matlab mathematical modelling software was developed to simulate the performance of the pilot conveyor. The model enabled to determine the design parameters of industry-scale conveyors to yield satisfactory performance. These conveyors become very cost-effective for those mines having large mine lives and depths greater than about 500 metres.

Jan 1, 2003

An Ammonia Leaching-Solvent Extraction-Electrowinning-Flotation Process for Copper Oxidised Ore Treatment

Sep 13, 2010

Understanding multiphase particulate systems is essential for the further advancement of mineral processing technology. Characterisation, analysis, and simulation of these complex systems provide a fundamental basis for the development of improved mineral processing technology. One of the more recent tools that can be used to help provide a foundation for improved mineral processing technology is high resolution cone beam X-ray micro computed tomography (CT). During the past ten years point-projection X-ray micro CT systems have been used for 3D visualisation and quantitative analysis of multiphase particulate systems. Analysis of packed particle beds containing as many as 30 000 particles can be accomplished in less than three hours with special software to establish the 3D characteristics of each particle in the population and the spatial organisation of the packed particle bed. Now, due to advances in X-ray optics, the resolution afforded with point-projection micro CT systems has been improved by at least an order of magnitude using a lens-based X-ray micro CT system. The development of software tools for the 3D characterisation, analysis, and simulation of packed particle beds using high resolution X-ray micro tomography (HRXMT) is discussed including examples of application in the areas of comminution (particle damage and preferential grain boundary fracture), exposure/liberation analysis (liberation-limited separation efficiency, including coal washability), and filtration/heap leaching (pore network structure of packed particle beds and simulated flow using the LB method of computational fluid dynamics).

Sep 13, 2010

Naturally occurring rutile contains approximately 96 per cent titanium dioxide (Ti02), whereas the product from the ilmenite reduction - aeration upgrading process, "sub- rutile", contains only about 92 per cent Ti02. Therefore, there is an-incentive to lift the quality of sub-rutile by removing transition metal impurities, in order to supply a more valuable and marketable product, particularly for the chloride-route pigment producers. Previous studies have shown that the sub- rutile residual iron content (of approximately 4 per cent) and residual manganese content (of approximately 1.5 per cent) are chemically bound within the titanium-oxygen mineral lattice, and are most difficult to remove by simple leaching methods. In attempts to improve their eventual removal, a simple process modification has been successfully investigated in laboratory scale trials. Transition metal sulphides have been formed in the reduced ilmenite by using a "sulphur-doping" technique during reduction (metallization) conducted at controlled temperatures. These compounds give rise to greatly enhanced dissolution of the unwanted transition metal constituents during the sub- sequent aeration and acid washing steps. Thus, the manganese content of the final sulphur- doped, reduced-aerated, acid washed product can be reduced by about 90 per cent to 0.2 per cent, and the iron content by about 70 per cent to less than 1.5 per cent, in comparison with those levels remaining after unmodified pro- cessing. Additions of sulphur as low as 2 per cent of the weight of the ilmenite have proven satisfactory. Preliminary studies reveal that the modified process is economically feasible. These results suggest that the sulphur content of the Collie coal char used in an unmodified reduction step must exert some influence on the eventual removal of iron and manganese during aeration and acid washing.

Jan 1, 1973

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Mssissippi Valley-type (MVT) and sedimentary-exhalative (SEDEX) zinc-lead deposits represent about half to three-quarters of the world's production and reserves of lead and zinc. The two deposit-types have traditionally been regarded as separate entities in terms of genesis largely because they possess very different morphologies, resulting from the epigenetic nature of MVT deposits and the syngenetic origin of SEDEX deposits. Similarities in regional setting, metal ratios, size and grade, lead and sulphur isotopes, and source(s) of fluids and metals in the two deposit-types, however, suggest that they could be products of similar genetic processes. The physical properties of MVT ore fluids suggest that certain types of SEDEX deposits could have been formed from fluids possessing similar salinities and temperatures. The hypothesis is further strengthened by the facts that: 1. in several cases MVT and SEDEX mineralisation occurs in the same region, and 2. recent advances in establishing the timing of MVT mineralisation has revealed that some MVT deposits are contemporaneous with nearby SEDEX deposits. If MVT and SEDEX zinc-lead deposits do indeed share a common ultimate derivation from fluids that emanated from sedimentary basins, then the presence of one deposit-type in a region could be used to infer the possible presence of undetected deposits of the other type. Furthermore, knowledge of the mineralisation age of one type will constrain the exploration target host rocks of the other type. A genetic relationship between MVT and SEDEX mineralisation may also explain why certain individual deposits, such as several in Ireland and eastern Canada, appear to be 'hybrids' and possess geological attributes of both end-member types.

Jan 1, 1993

By K Myers

Since the mid-1990s, the Chino Mine Facility (Chino) located near Silver City, New Mexico has been developing a closure plan with financial assurance to protect water quality, as required by State regulations. In February 2002, Chino and the New Mexico Environment Department (NMED) reached agreement on a closure plan; a closure cost amount of approximately $US 394 million ($A 591 million) was finalised in April 2003. Both the New Mexico Water Quality Act Regulations (1977) and the New Mexico Mining Act Regulations (1993) guided development of the closure plan and financial assurance amount. The process incorporated many years of correspondence, studies, negotiations and administrative hearings. The major technical issues focused on regrading slopes of the leach ore stockpiles and waste rock piles; cover systems; water treatment systems; and abatement of ground water contamination. The proposed financial assurance amount covers all closure costs and provides for perpetual water treatment.

Jan 1, 2003

By R M. S Watsford, M Davis

In 2015, MMG Limited commenced further action to improve operating margins and establish a blueprint for future growth in the Australian environment. This action was taken in the context of weakening metal prices and high input costs that arose during the Australian minerals boom.MMG was formed in June 2009 following the purchase of the majority of assets of OZ Minerals Limited by China Minmetals Corporation (CMC) through its subsidiary China Minmetals Non-ferrous Metals Co Ltd (CMN).Since formation MMG has been implementing a business model to deliver a standard way of operating. The overarching purpose of the business model is to enable fast integration of acquired assets to realise improved productivity and performance. CMN established MMG as a vehicle to reach their growth targets through further development or acquisition of mineral assets in jurisdictions external to mainland China.The business model is underpinned by the MMG operating model. The operating model defines how MMG is arranged to deliver the company strategy.This paper describes the application of the operating model to the formation of the Australian operations into a single business unit from multiple stand-alone operating sites. The development and impact of the business model on MMG’s performance is also presented.The extension of the operating model to the Australian operations has led to improvement in safety performance, direct costs and productivity. These improvements have been achieved through reducing duplication, simplification of systems and rapid deployment of improvement initiatives.The successful implementation of the operating model to Australian operations strengthens the platform for further growth. Hence, delivering on the aim of the business model.CITATION:Watsford, R M S and Davis, M, 2016. MMG’s Australian operating model – the implementation, successes and learning, in Proceedings International Mine Management Conference, pp 291-302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

Blast furnace slags which fall into the quaternary system SiO2 - A1203 - MgO - CaO have latent hydraulic properties which depend on the degree of vitrification. When the oxides com- bine to form Calcium Silicate Hydrates and other products of hydration the bonds between elements are at a lower energy level than those which exist in the glassy state. Transition from the glassy state to the crystalline state is thermo- dynamically favoured and, in the context of this paper, such slags possess internal energy. Manufacture of Portland cement is respon- sible for about 3.6 per cent of total industrial energy consumption in Canada. Pyroprocessing accounts for about 83 per cent of this figure or 3 per cent of the total. The processing of blast furnace slag to a condition in which it can be used as a partial substitute for Portland cement requires no pyroprocessing and, on average, only about 11 per cent of the energy needed for Portland cement. In North America the benefits of slag as a cementitious materials have been obscured by other considerations, the most important being commercial strategy. This situation has under- gone radical change as a result of the rising cost of energy, and government pressures to conserve energy.

Jan 1, 1979

Continuous processes must be shutdown and restarted regularly. Results from the study of operating plants showed potential value for computer simulation of the shutdown and startup of stirred tank leaching reactors. Simulation allows operational variables such as feedrate, and process variables such as the dissolution kinetics to be altered to establish trends in behaviour. Results are presented for the start- up of a cold, empty, single stirred tank reactor, in which three solids are leached at elevated temperature at steady state. Increasing the average temperature in the reactor during startup did not change the fraction of 'valuable' solid dissolved in the first product but it did increase the fraction of slow dissolving (impurity) solid dissolved.

Jan 1, 1984

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By T Nixon

A common problem for many mines is insufficient total primary airflow or insufficient airflow in the correct places as the mine changes over its life. This has a number of impacts on the business operation and may result in the need for a major and unexpected capital upgrade of the system, cancellation of a planned production increase, reduction in production targets, increased operating costs, failure to provide contracted metals to customers or acceptance of substandard conditions in the workplace. In some cases, it can even result in premature closure of the mine. In recent times, higher metal prices have given an expected economic boost to many mines, potentially prolonging their life but simultaneously requiring the mine to develop to deeper depths or requiring assets such as shafts and fans to have their service life extended. Insufficient primary airflow is a particular problem in deeper mines as the ventilation circuits become longer, more convoluted, have higher shock losses and the actual airflow requirements increase due to a combination of leakage, dispersion of the workings and the problems of managing the additional heat loads due to higher virgin rock temperatures and autocompression. This paper discusses the reasons why mines experience unexpected shortfalls in primary ventilation capacity with its associated impacts on metal targets, profits and frequently on the health, safety and morale of the workforce, as well as its productivity.

Jan 1, 2008

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Cretaceous volcanic activity (Hauterivian Albian) in the Peruvian Andes can be found along the coast of Peru and the western edge of the Andes mountains between 15o30'S and 5o30'S, extending discontinuously in south to Chile and north to Ecuador and Colombia. This volcanic activity formed in three aborted marginal basins; the NNW-trending volcanic Ca±ete and Huarmey, and NNE-trending Lancones basins. These volcanic rocks are predominantly andesitic and basaltic in composition, of calc-alkaline and tholeiite affinity with subordinate dacitic and rhyolitic rocks. One notable feature is the appearance of æocoitasÆ from Ica (14oS) south to Santiago de Chile. These rocks have a calc-alkaline to alkaline affinity. From south to north, the continental crust gradually becomes thinner, allowing mantle material to rise towards the surface. Ophiolitic sequences of this type form a marginal basin in Colombia. Very low-grade regional metamorphism which affects the volcanic rocks also varies gradually from south to north. Between Santiago de Chile and Ica this takes the form of burial metamorphism, with moderate geothermal gradients (20o-30oC/km). Metamorphism in the Huarmey basin is transitional between burial and ocean-floor metamorphism, with very high geothermal gradients (>3000C/km). High geothermal gradients are also apparent in metamorphism of the Lancones basin, though less than the other basins. Ocean-floor metamorphism is present in the ophiolitic sequence in Colombia. Associated mineral deposits in the Huarmey and Lancones basins, and in the north, are of the volcanic massive sulphide-type (VMS). The principal deposits in Peru are Leonila Graciela (20 Mt Zn and Pb) and Tambogrande (40 Mt Cu and Zn). There are also smaller mines and prospects. To the south of Lima, manto-type Cu deposits (CuMT) are found with a mineralogy of chalcopyrites, pyrites, magnetite, actinolite and apatite. The main example is Raul Condestable (10 Mt Cu). Other prospects are present to the south and Chile has some very large mines of this type (El Soldado, Lo Aguirre). The notable differences between the CuMT and the VSM deposits are thought to be the result of the prevailing conditions in the earthÆs crust during the Hauterivian Albian. To the south, calc-alkaline and alkaline volcanic activity in aborted marginal basins, with thicker crust, was thick, produced moderate geothermal gradients associated with burial-type regional metamorphism and deposits of CuMT. In the north aborted marginal basins associated with calc-alkaline to tholeiitic volcanic activity and a gradually thinning crust, produced transitional regional metamorphism between burial-type and ocean-floor type, associated with high to very high geothermal gradients and VMS deposits. In Colombia these conditions led to ophiolite extrusive rocks, ocean-floor metamorphism and also VMS deposits.

Jan 1, 1999

By Caigen Wang, Wending Ma, Xiexin Mi

The urgent need for the control of surface subsidence caused by longwall coal mining in densely populated areas of China has led to a feasibility study on the effectiveness of longwall goaf cemented backfill. The study is focussed on exploring the potential of longwall goaf cemented backfill practice for surface subsidence control. Specific backfill geometry was designed in view of the characteristics of the longwall coal mining system. Laboratory physical simulated tests were carried out with different backfill material properties and pack size. The tests achieved a marked reduction in surface subsidence by the use of goaf cemented backfill. The system has been shown to be effective in laboratory tests, the challenge now is to overcome the engineering problems to put it into practice.

Jan 1, 1998

By M J. Nugus, J G. McLellan, T G. Blenkinsop

High fluid pressures and deformation have been instrumental in the formation of high-grade gold lodes at the Archaean granite greenstone 12 Moz Sunrise Dam gold deposit in Western Australia. Historically, predicting the location of these lodes has been difficult due to the irregular nature and high-grade nugget characteristics of the deposit. Recent exploration successes and the discovery of the Vogue system have led to an improved knowledge of the deep extents of the mine. This new structural and gold distribution data has enabled a new 3D interpretation of the system and has provided a better insight into the links between deformation, fluid pressure evolution and gold deposition. Here we employ 3D geomechanical and coupled fluid flow modelling to better constrain areas of high strain partitioning, rheological failure and focused fluid flow, which provides a substantially increased predictive capacity for further within-mine exploration. The localisation of deformation in and around the main felsic porphyry and major shallow shear zones provides critical insights into fluid pathways that have contributed to the distribution of fracture networks and ultimately gold deposition during late stage deformation events. Understanding the relationship between deformation events, fluid pressure evolution and the partitioning of strain is paramount in understanding the distribution of gold and for focusing on future target areas.CITATION:McLellan, J G, Blenkinsop, T G and Nugus, M J, 2013. Fluid pressure, geomechanical evolution and predictive targeting of the Sunrise Dam gold deposit, Western Australia, in Proceedings World Gold 2013 , pp 419-426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013