Search Documents

By Moxon NT

The detonation pressure of ANFO can be significantly reduced by the addition of low density materials such as polystyrene, bagasse, sawdust or perlite. Laboratory and field test results have shown that homogene- ous mixtures of these low density explosives can be produced in a bowl truck and loaded into a blast hole without segregation. The detonation pressure of the mixture can be tailored to suit the material to be blasted by varying the quantity of low density additive incorporated into the mix- ture. Results obtained in the field indicate that these low density explo- sives can lead to significant cost savings without compromising fragmentation or production.

Jan 1, 1988

By L R. B M Sß

This paper presents the results of a liberation study made on a sulfide copper ore from Carajßs, Brazil, in a mini pilot plant flotation test. The aim of the research was the methodological evaluation of a liberation study using a sample crushed at 1 mm and a sample ground for flotation testing to a target size of 80 per cent

Jan 1, 2005

By K Edwards, A J. J Mouton

Hematite represents the vast majority of iron ore exported from Australia as the development and processing cost of magnetite is generally seen as a barrier to the development of vast magnetite resources. However, a number of magnetite projects have attracted a significant amount of interest and investment from large Chinese steelmakers.This paper compares the relative merits of the development of Australian magnetite and hematite ore from the point of view of the steelmaker, taking into account the factors that influence the capital costs of the development of the ore types and the relative costs of operating the process plants to treat these ores. By modelling the relative operating cost for the production of hot rolled coil in China for the two ore categories, the paper demonstrates the economic drivers behind the Chinese steelmakers’ large investments in the magnetite resources of Western Australia. It does this by estimating the potential value of magnetite concentrate to the steelmaker in the event that the maximum potential is realised by operating the blast furnace with a 100 per cent pellet burden.Under the conditions described, it was found that direct reduction (DR)-grade magnetite concentrate could command a price premium over 62 per cent Fe fines of up to 46 per cent (December 2014 on a cost and freight (CFR) basis). The corresponding premium for blast furnace (BF)-grade magnetite concentrate is 17 per cent, which demonstrates the dependency on grade.The capital expenses for a 14 Mt/a concentrate plant is estimated at US$3.1 B for BF-grade magnetite and US$3.35 B for DR-grade, with operating expenses at US$45 and US$50 respectively. The corresponding free on board price for a break-even net present value is calculated at US$82/t for BF-grade magnetite and US$90/t for DR-grade. The minimum long-term iron ore price (62 per cent Fe) that would be required to underpin such a project is estimated at US$78/t CFR for BF-grade magnetite and US$68/t CFR for DR-grade concentrate.Apart from the financial benefits, it is demonstrated that the use of magnetite concentrate in ironmaking has the potential to reduce CO2 emissions by approximately 400 kg per tonne of hot rolled coil.CITATION:Mouton, A J J and Edwards, K, 2015. Magnetite – a higher-grade blast furnace feed and its potential benefits for the ironmaker, in Proceedings Iron Ore 2015, pp 613–620 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Kahler

Modern gold production from the Gympie Goldfield commenced in 1995 with the first production from the Monkland Mine. The primary ore target was the 2.5 m wide Inglewood Fault ore zone, which was initially mined using traditional narrow-vein shrink stoping. This manuallyintensive mining method allowed the mine to re-open with minimal capital cost, however the trade off was low productivity and high operating costs. As the mine has developed, access through 100-year-old, timber-lined, small shafts, and the high cost of delineating reserves, has restricted modernisation of the operations. In early-2000 a stockwork lode was discovered adjacent to the existing workings with an economic width of 40 m. In order to maximise the benefit of such an orebody, mining needed to be approached in a new way. This paper summarises the many changes implemented at the Monkland Mine, including the necessary cultural change, implementing long-hole stoping, de-bottlenecking and the application of mechanisation. The result has been a significant improvement in safety performance, higher productivity and a more secure future for all those involved in the project.

Jan 1, 2002

By J F. C L Costa, J C. Koppe

It is recognised by the major international codes that resource classification involves the interaction of numerous qualitative and quantitative criteria such as data quality, geological and grade continuity, etc. However, the difficulty in quantifying the degree of uncertainty associated with mineral resources estimation has led to the creation of a large suite of methodologies, terms and definitions, with almost every mining company having its own set of standards. It is also intuitively known that several traditionally used methods to evaluate resources do not take into account the spatial continuity of the grades, being unable to provide a reliable measure of the error associated with their estimates. Since they do not provide an error assessment, these methods are inappropriate to assess local or global uncertainty associated with an estimate. Faced with these problems, this work aims at developing a methodology for either quantitative or qualitative analysis of mineral resources estimation, through incorporation of uncertainty and the correct definition of the associated risk or error. The proposed methodology includes the development of a software code incorporating all the main classification techniques used by the mineral industry. A comprehensive study about each technique was conducted allowing a comparison of the parameters affecting mineral inventory assessment. A case study was conducted with a typical iron ore deposit data set from the Conceitpo mine of the Itabira Complex in the Iron Quadrangle, Brazil. The results showed the specific limitations of each classification system and the influence in selecting their key parameters, always based on subjective choices.

Jan 1, 2009

By Liu Wenyong, Huang Yucheng, Yang Ba

High-water rapid-solidifying material, called æhigh-water materialÆ, is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of backfill body, environmental contamination and so on, have been solved.

Jan 1, 1998

Petroleum exploration and development is vitally important for the future well being of Australia. The Australian petroleum exploration/development industry is alive but not so well. A combination of.:factors point to the industry requiring a much more mature effort in both short and longer-term planning to ensure greater success and effectiveness for petroleum discoveries and development. While many petroleum exploration companies are competently run, there are far too many which will be lucky to survive, even though their exploration areas are highly Prospective.

Jan 1, 1983

An integrated mining equipment development organisation is typified by Deutsche Montsn Technologic of Essen, Germany. working on improvements in reliability, production and control in coal mines. Examples of recent mining advances are in mechanised roadheading, in different approaches to cutting technology, and in low height roof bolting.On the longwall face the mechanics of cutting are related to supplied energy as well as to dust make. In conveying both armoured face conveyors and conveyor belts are monitored. Roof support is not neglected and the continuous pumping of stowage slurries provides further options for longwall support. Surveying developments, particularly the gyro-theodolite, directional drilling. and shaft vehicle monitoring provide further examples of advances in control in coal mining activities.

Jan 1, 1991

The mining production rate of two million tonnes per annum at Olympic Dam required greater servicing capacity than was available with the existing Whenan Shaft. To increase servicing capability a Service Decline was constructed from June 1986 to June 1987 extending 2000 m from the surface and linking up with inclining development from the existing Whenan Shaft workings. The decline was used for access of all men and materials during the construction phase of the ore handling system. During production, most mine servicing will be via the decline with hoisting of rock through Whenan Shaft.

Jan 1, 1988

A laminar-flow furnace was used to study the combustion of four flotation concentrates (chalcopyrite, pyrite, galena, and sphalerite) in air at temperatures up to 1400¦C. A special- Iv developed two-colour pyrometer was used to measure the temperature of individual chalco- pvrite and pyrite particles as they underwent combustion. Chalcopyrite and pyrite ignited with very high rates of reaction at air tempera- tures above 480 and 600¦C respectively, forming molten products. Galena and sphalerite required temperatures in excess of 700 and 1200¦ respect- ively to attain equivalent rates of reaction. The high rates of reaction for galena and spha- lerite were caused by vaporization. Temperature measurements for chalcopyrite and pyrite are reported here, together with vaporization measurements for chalcopyrite, galena, and Sphalerito

Jan 1, 1980

By A Grace, C Sennersten, A Davie, R Lyu, C A. Lindley, O Goldstein, T Thomas, L De Macedo Camargo

Block modelling is a well-established method for modelling ore reserves as a basis for strategic mine planning and mine development. Off-Earth mining, particularly of asteroids, can benefit from block models; however, the significantly different characteristics of asteroids and their methods of mining require reconsideration of the geometry and annotations of block models. Terrestrial block models consist of rectangular prisms within Euclidean coordinate systems. Their labels and parameters typically include location within a mine-specific coordinate system, x, y and z dimensions, specific gravity, hardness, grades of metals of interest and so on.These data provide an input to mine design and strategic mine planning. Mining asteroids may require different coordinate systems (eg spherical, elliptical or cylindrical, rather that Euclidean) and attributes that vary from Earth-based block models. These include: variable gravitational vectors throughout the block modelrotational moment or accelerationrotation rates. Materials within asteroids may show different isotopic compositions. Asteroid mining has the unique characteristic of a mine being identical with an asteroid. The position of the asteroid/mine in space and its full orbital elements provide critical inputs to mission design and costing. Hence, the block model concept needs to be extended with this metadata. The orbital position and behaviour of the Earth must be included for active mine planning, and increasing automation of mine planning and operations needs to consider terrestrial weather and telecommunications infrastructure. Financial planning requires analysis of the net present value of extraterrestrial mining compared with terrestrial alternatives, so a fully automated mining enterprise should integrate terrestrial and extraterrestrial block models at different scales and resolutions. Blocks can be indexed via octrees, allowing for hierarchical scales that support analytics for deriving new knowledge and correlating features across different scales.CITATION:Lindley, C A, Sennersten, C, Davie, A, Goldstein, O, Lyu, R, Grace, A, Evans, B, Pentecost, D, Thomas, T, De Macedo Camargo, L, Craig, J, Salomao, G N, Hellicar, A, Biggins, D, Timms, G, Coombe, M, Shahriar, M S, Smith, G and Rahman, A, 2015. A multilayer 3D index tool for recursive block models supporting terrestrial and extraterrestrial mine planning, in Proceedings Third International Future Mining Conference, pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

The Callie Underground Mine is located in the Tanami Desert 560 km Northwest of Alice Springs in the Northern Territory and is currently operated by Newmont Australia Limited with all mining activities carried out by Henry Walker Eltin. Callie was discovered in the region in 1991 with the box cut portal commenced south of the pit in 1995 and underground ore production commenced in 1998, after completion of the profitable Callie Open Pit. Development is currently occurring at depths of over 700 m with the decline currently below the 640 Reduced Level (RL) level (surface RL of 1400) with production haulage from 600 m below the surface. The combination of auto compression, a moderate geothermal gradient of 2¦C/100 m and diesel heat transfer causes the wet bulb temperature of intake air at the bottom of the mine to be typically 5¦C higher than on the surface. Wet Bulb temperatures can be up 5¦C higher again in active areas under secondary ventilation. During the 2002/2003 wet season many activities in the lower levels of the mine were stopped due to miners experiencing adverse heat related symptoms or the temperatures exceeding the Underground Heat Management Procedure stop job criteria of 32¦C wet bulb. To improve the working environment, combat the heat related illness and improve operational efficiency, a temporary 1.8 MW refrigerated cooling plant consisting of three 600 kW modules were installed underground to provide bulk air cooling for the lower levels of the mine during the 2003/2004 wet season. Several studies have been conducted in relation to future ventilation demands at Callie and all came to the conclusion, that some mine cooling will be necessary for Callie to meet the high production and development demands. This paper will describe the ventilation network at the Callie Underground operation focusing on the installation, operation and effectiveness of the temporary underground refrigeration plant.

Jan 1, 2005

Madison Enterprises Corp. and Matu Mining are currently ex- ploring the Mt. Kare property in Papua New Guinea. The Mt. Kare gold prospect has had a short but very active history, since the first discovery of gold in the area in 1986 the property has sccn: a 3 year gold rush during which 10,000 alluvial miners re

Jan 1, 1997

By R Cox, S Pandey

The coal seam gas (CSG) industry is expanding rapidly in the Surat and Bowen basins. CSG production involves pumping water from the coal seams to release the gas adsorbed to coal particles. The reduction in water pressure in the coal seams will cause some reductions in water pressure in overlying and underlying aquifers because there will always be some interconnectivity between the formations. The Surat Basin is a sub-basin of the Great Artesian Basin, which contains aquifers of high economic, environmental and cultural value. The Condamine Alluvium is also an important water resource, which overlies parts of the eastern margin of the Surat Basin.Under the Queensland (Qld) regulatory framework, an area of intensive CSG development involving multiple CSG operators can be declared to be a cumulative management area. For such areas the Office of Groundwater Impact Assessment develops assessments of future impacts on aquifer water pressures and develops and manages arrangements. The results are published in underground water impact reports.The Surat underground water impact report (QWC, 2012) was approved in December 2012. This paper summarises the place of the report in the Queensland regulatory framework, the content of the report and progress in its implementation.CITATION:Cox, R and Pandey, S, 2013. Managing groundwater impacts in the Surat Basin, in Proceedings Water in Mining 2013 , pp 169-174 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By J A. Wells, K G. Thomas, R F. Dewhirst

"One of the contributing factors to the extreme cost escalation in the first decade of the 21st century was the increase in the amount and cost of engineering work that went into studies and projects. Various reasons for this were identified, including unsatisfactory productivity due to a shortage of experienced/qualified engineers, the increased complexity and infrastructure requirements of many projects due to location, metallurgy that is more challenging and increasing environmental and social requirements. These conditions often led to unsatisfactory project results in terms of cost and schedule blowouts and created a loss of confidence – both internally and externally – in the industry’s ability to complete projects on time and on budget.Technical fundamentals aside, the experience and effectiveness of project teams has had, and continues to have, a major impact on project cost, schedule and ramp-up to nameplate capacity and operating parameters. There are unfortunately too many examples of where project teams have not been as effective as they could or should have been, all to the ultimate detriment of the project.Using the authors’ extensive experience on both owner’s and engineer’s teams, this paper discusses some of the main reasons for suboptimal team, and hence project, performance and offers thoughts on how best to build and maintain project teams. The analysis and conclusions drawn are built around the Tuckman model of group development known as ‘forming-storming-norming-performing’, which was first proposed some 50 years ago. Given the importance of good teamwork to project success, understanding how project teams grow and become efficient and productive is an essential part of good project management that should receive more attention.CITATION:Dewhirst, R F, Thomas, K G and Wells, J A, 2016. Building and maintaining effective project teams, in Proceedings Project Evaluation 2016, pp 38–48 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By L D. Meinert

Skarns typically are zoned and the deposit- or district-scale zonation pattern is an important tool in exploration for skarn deposits. Zonation in individual deposits has been described in many publications, and the general zoning patterns have been summarised by Einaudi, Meinert and Newberry (1981), Meinert (1997), and Meinert, Dipple and Nicolescu (2005). Although zonation is present in most skarns as the result of a basic process of transferring heat and fluids from magmas to wall rocks, the specific zoning pattern in each skarn may vary greatly. For example some zones may be missing entirely or multiple zones may be telescoped. Such variations can be caused by several factors including depth of formation, magma composition, timing of the exsolution of magmatic aqueous fluids, redox state of the magma and redox state of the wall rocks. To use zonation as a predictive tool in skarn exploration, all the controlling factors have to be considered. In this study, we discuss some of the factors that may affect the zoning patterns in Ca skarns. Magnesium skarn has dramatically different mineralogy and is not discussed here. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J R. Manuel, J M. F Clout

The importance of goethite to Australian iron ore production is steadily increasing as the proportion of goethite-rich, martite-goethite bedded and channel iron deposits increases at the expense of declining production from high-grade microplaty hematite deposits. For this reason, an improved understanding of goethite in iron deposits, its genesis, goethite types and their physical and metallurgical properties is vital to maintaining optimum sintering and blast furnace performance in Asian steel mills.The terminology used to describe goethite in Australian iron deposits is currently highly variable. The discredited mineral name ‘limonite’ is still in widespread use as a field term for goethite and there are many misconceptions concerning goethite chemical grade and downstream physical and metallurgical properties. The goethite classification proposed here is based on geological and physical properties from which three types are recognised including brown goethite, dark brown-black vitreous goethite and highly microporous, friable yellow ochreous goethite.In practice, typical vitreous goethite with highly reflective surfaces and conchoidal fracturing, characteristic of the hard cap zone appears from X-ray fluorescence (XRF) and electron microprobe analysis to be significantly higher in Si (up to 18.7 wt per cent), Al (up to 3.5 wt per cent) and S (up to 0.14 wt per cent) compared to the generally very low (<1 wt per cent for Si and Al) levels of these elements in ochreous goethite and brown goethite. The data dispels the common misconception that friable earthy or yellow ochreous goethite is high in Al and Si and other chemical impurities. However, P was found to be consistently higher (mean of 0.112 wt per cent and up to 0.296 wt per cent) in ochreous goethite than brown goethite (mean of 0.011 wt per cent) or vitreous goethite (mean of 0.031 wt per cent). The highly porous microstructure of ochreous goethite is thought to have a much higher surface area, which may aid in preferential adsorption of P onto the ochreous goethite mineral surface.CITATION:Manuel, J R and Clout, J M F, 2017. Goethite classification, distribution and properties with reference to Australian iron deposits, in Proceedings Iron Ore 2017, pp 567–574 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Solid. dense, air-cooled slag can fulfil most, if not all, the functions of natural stone for civil engineering purposes. The value of pumice, also, has long been appreciated, and processes for the manufacture of similar synthetic material for light-weight concretes and insulating fills have been developed in past years.Foamed slag is, in effect, blast furnace pumice and is often referred to on the European continent as metallurgical pumice. It is made by the treatment of molten blast furnace slags with a critical quantity of water during which process the slag cools and expands into a sponge-like mass. The connection between foamed slag and air-cooled slag is also considered and a basis for density control given.All blast furnace slag cannot be foamed to give a product which would comply with B.S.S.877; 1939 Foamed Blast Furnace Slag. A large proportion of the total output of molten slag lacks the necessary inherent properties. This investigation attempts to discover the conditions necessary for the production of foamed slag capable of meeting the British specification.EARLIER WORKIt was generally accepted (Parker, 1951; Gallai-Hatchard, 1955) that the spongy structure of foamed slag was caused mechanically by steam trapped in the slag when it was poured into water. It was assumed that slags which would not foam would not trap steam, because their viscosities and surface tensions were unsatisfactory, on account of temperature and/or composition. The earliest systematic investigation was made by Frisak (1923) who attempted to establish a limiting chemical composition for foamable slags. He decided that foamable slags covered most blast furnace slag compositions on the basis of silica, alumina, and lime, and further "that the replacement of lime by magnesia up to 15 per cent has no noteworthy effect on foamability, that moderate quantities of alkalis are not deleterious, that sulphur raises the foamability and that MnO is only deleterious in the presence of 1...

Jan 1, 1963

By D J. Black

The process of excavating and mining coal causes fractures in the overlying and underlying strata. The fractures provide pathways for gas released from coal seams and other gas-bearing strata to flow into the mine workings. Coal seam gas typically contains high concentrations of methane with lesser concentrations of carbon dioxide. Low concentrations of other gases such as nitrogen, hydrogen sulfide and ethane may also be present in some coal seams. In certain geological settings, particularly in close proximity to geological structures, such as faults and dykes, the concentration of gases contained in a coal seam can vary significantly between methane-rich to carbon dioxide-rich.In mine design and planning it is vital that mining engineers gather sufficient information to accurately determine the content and composition of the gas present in the coal seam and develop an understanding of changes in these parameters within the planned mining area.The longwall method of mining coal causes fracturing of the overlying and underlying strata behind the retreating longwall face. Where coal seams and other gas-bearing strata are present within the caving zone, gas will be released from the strata leading to contamination of the mine workings. If the rate of gas emission exceeds the diluting capacity of the mine ventilation, the concentration of gas in the mine may exceed the statutory limit, resulting in production delays and potentially unsafe conditions.CITATION:Black, D J, 2016. Planning effective management of gas emissions in an underground coalmine, in Proceedings Life-of-Mine 2016 Conference, pp 44–47 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016