Search Documents

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

By M F. Gazley

The amphibolite-facies metabasaltic rocks of the Mine Mafic Package at Plutonic Gold Mine, Marymia Inlier, Western Australia, contain an estimated total endowment of 12.2 Moz of Au, which includes 4.71 Moz of past production and 2.77 Moz of reserves and resources; the remainder comprises lower-grade inventory. Over 65?000 multi-element analyses of whole-rock core and face channel samples from the underground workings of the deposit have been collected by portable X-ray fluorescence (pXRF) using a handheld Innov-X Omega pXRF unit. The analyses were performed on pulverised samples through paper bags, and were corrected using a pulverised, matrix-matched, reference standard. This method of data correction compares favourably with conventional XRF analyses performed on the same samples.A preliminary study based on pXRF analyses from a small number of drill holes found that a geochemical stratigraphy was evident in the pXRF data, and that this stratigraphy strongly controlled the location of Au mineralisation. The present study incorporates a much larger pXRF data set that samples a greater volume of diamond drill core and face channel samples and presents the data in a three-dimensional (3D) framework.This data set allows an investigation of the mineralogy of Au mineralisation with varying geochemical associations across the deposit. Historically, there has been a strong relationship identified between As and Au, which has caused issues with metallurgical performance, rendering some areas of the deposit only marginally economic. Utilising seamless data integration of the pXRF data set allows for recognition of the different styles of Au mineralisation using elemental concentrations and ratios from the multi-element analyses (Au:As, Au:As:Cu, As:Cu vs. K:V), and to visualise the distribution of these different mineralogical associations in 3D. The results of the 3D modelling and geochemical characterisation of the different styles of Au mineralisation are currently the focus of an extensive metallurgical testing program, the preliminary results of which are presented here.

Aug 22, 2011

By T Arena

To maintain copper recoveries and maximise production at the Sepon Copper Operation it is crucial to control the amount of copper entering the leaching circuit. This requires close control of blending of the multiple ROM stockpiles to achieve the desired head grade. Grade variability in the ROM stockpiles can lead to significant variation in the processing plant copper feed grade.Head grade sampling from the milling circuit at Sepon is complicated due to milling in leach solution to preserve the water balance. Copper is present in both liquid and solid forms and copper in the added milling solution has to be accounted for. This leads to difficulties in manual head sampling which also introduces delays due to sample preparation and assay turnaround. On-stream analysis is complex because of the solution and solid copper and the need to account for recycled copper solution.This paper describes the complexity of feed grade management at Sepon and the application of on-belt analyser technology to assist in the control of copper metal throughput.

Aug 8, 2011

By D Wimpenny

Underground infrastructure is often a critical component of transportation and utility schemes. It is characterised by long design lives with limited access for inspection and maintenance. The exposure environment can be difficult to assess since it will often vary substantially between different locations in the same facility and with time during construction and in service. In addition, the specific demands placed upon underground infrastructure are not well covered by the exposure classes and other guidance given within current codes of practice. When problems occur they can be difficult to rectify and involve significant disruption.Given these substantial risks the prudent designer may adopt a systematic ‘durability planning’ approach which:· defines the environment and principal deterioration mechanisms for the various elements and construction materials,· predicts the design life for alternative durability enhancement options, and· recommends associated measures to be adopted during construction and in service.This paper describes the development of durability planning within Halcrow, giving examples of its use from its first implementation on tunnels under the Suez Canal in 1993 to recent projects in the Middle East and Australia. It seeks to demystify the process, identify shortcomings and speculate on its future development within the civil and mining sectors.

Mar 8, 2011

By R L. Koenig

The rediscovery and recognition of the magnetite potential of the iron mineralisation at the Hawsons Project area 60 km south of Broken Hill has the potential for the development of a new series of magnetite iron-ore operations across the Braemar Iron Formation in New South Wales and South Australia. Despite the low-grade of 16 per cent magnetite, the Hawsons project feasibility studies are indicating a positive business case for a large-scale 20 Mt/a of magnetite project for the following reasons:• The mineralisation is on a huge scale, with a major potential for increases beyond the already very large established resource of 1.4 Bt.• The mineralisation is particularly soft for crushing and grinding, with a Bond work index of 6.3 and an overall comminution power requirement of 6.7 kWh/t of ore. This equates to 39 kWh/t of concentrate which is significantly less than for similar projects.• The mineralisation fractures easily, preferentially along grain boundaries.• Location is close to mining infrastructure and a skilled workforce at Broken Hill, 60 km to the northeast.• It is close to road and rail infrastructure for access to the resource.• A high-grade, clean magnetic concentrate can be produced, with the only contaminant being silica.The deposit is a sedimentary siltstone which is considerably different to other known magnetite deposits. This caused significant differences in Davis Tube Recovery (DTR) results between laboratories so that the softness of the ore has required a close focus on, and changes to the laboratory procedures. A DTR procedure has been developed to provide consistent results across the deposit.Crushing and grinding test work has established a clear advantage in the use of the high-pressure grinding rolls (HPGR) crushing and grinding circuit for this particular ore. The power required for comminution using the HPGR crushing circuit is about half the power required for the Autogenous milling circuit.Therefore, despite the low magnetite grades, the Braemar Iron Formation in New South Wales and South Australia has the potential be a new magnetite iron ore province.

Jul 11, 2011

By Wyborn L, Giddings J. W, Plumb K. A

The McArthur, Balma (new name) and Habgood Groups are thick (up to 4.5 km) correlative sequences of shallow water evaporitic carbonates, mudstones and sandstones that are exposed largely within the Batten, and southern and northern Walker Fault Zones (Batten and Walker Troughs) of the McArthur Basin respectively. Recent re-mapping of the Walker Fault Zone has provided data for refined stratigraphic correlations between these groups. Two significant hiatuses are now recognised within the Balma Group (base of Vaughton Siltstone and base of Yarrawirrie Formation) and these may represent tectonically-generated sequence boundaries which may correlate with similar local hiatuses within the McArthur Group such as at the base of the Teena Dolomite and Lynott Formation respectively.

Jan 1, 1994

By M A. Wells

A new approach to more reliably predict the Ni (and Fe, Mg) composition of Ni laterites was tested for RC samples from the (siliceous) oxide–style, Siberia North deposit, Kalgoorlie Nickel Project (KNP), in the north-eastern Yilgarn (WA) using partial least squares regression (PLSR) analysis of diffuse reflectance spectra over the 380 - 2500 nm wavelength range with a multi–element chemistry data set. PLSR cross-validation models were developed to predict FeO, MgO and Ni contents in composite samples with bulk composition limits of >0.08 wt per cent Ni and <6 wt per cent MgO. Calibration and validation models showed a strong, linear trend for predicting FeO and, to a lesser extent, Ni content, whereas PLSR models for predicting Mg content were less reliable. This reflected the prevailing mineralogy and associated element deportment within the oxide laterite profile. For example, Fe and Ni distribution is controlled by relatively few minerals, predominantly goethite and, to a lesser extent, the Fe3+-bearing smectite, nontronite. Magnesium is associated with a range of Mg-bearing minerals, some of which are compositionally complex (eg serpentine, talc, chlorite, smectite and carbonates). Magnesium chemistry alone does not reflect the varied mineralogy of samples with relatively high (5 - 6 wt per cent) MgO contents, which can be spectrally distinct. Hence, samples with similar Mg contents, though comprising Mg-bearing minerals with distinct reflectance spectra, were difficult to model (eg smectite versus Mg-carbonates). The findings of this study demonstrate that characterisation of Ni laterite composition may be achieved as part of routine logging of either drill chips or diamond drill core using PLSR analysis, but that a detailed understanding of the mineral-element association is essential for reliable predictive analysis. This has particular relevance to characterising the geometallurgy of Ni laterites, especially where deposits may be classed as the same type, but have distinct compositional and mineralogical differences.

Sep 5, 2011

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By D Matthews

Increases in mining and production capacities can have a major impact on the productivity of a mining and production facility during the construction and commissioning period. With minimised production loss in mind, a multi-phase modular plant design was implemented on the Khumani Mine in the Northern Cape, South Africa. The first phase involved a run-of-mine (ROM) crushing facility and the subsequent modular processing facility with capacity for 8.4 million tons per annum (Mt/a) product. An interim phase comprising modular additions to the processing facility increased capacity to 10 Mt/a product, with tie-ins occurring during maintenance periods. The second phase involves a second ROM crushing facility and modular additions to the processing facility, increasing capacity to 16 Mt/a product. This paper outlines the design considerations and limitations with modular design that need to be considered and shows how effectively construction and commissioning were implemented within shut-down and maintenance periods.

Jul 11, 2011

By J Ross

The foundation of effective leadership is communication. You can have all the leadership theories, models and training you want, but in the end it is all about leaders talking to, listening to and understanding the point of view of those below and above them.The foundation of effective safety is peoples’ behaviours. Every incident, every near miss and every safe act comes down to what one person does and how that affects themselves and others. We tend to focus these behavioural considerations on the people at the ‘coal face’, those most in harm’s way. But it is the individual behaviours of everyone in the organisation, particularly those at the top, which are just as (if not more) important. The foundation of effective safety leadership in the mining industry is that it starts at the top, with the individual behaviours of leaders. The behaviours of each and every leader will be reflected in their teams. And where their teams are made up of leaders, these leaders will pass these behaviours on to their teams and so on. It’s the sum total of what people see their leaders do and what they do as a result, that creates the ‘culture’ of the business – and it’s this culture that makes or breaks how safely people work.

Mar 21, 2011

By G A Brown

Environmental legislation is changing rapidly throughout Australia at the present time, and with that change comes additional responsibilities for the mining and petroleum industries. Among the many changes that are being made are increased penalties for both criminal and accidental environmental impairment. The defences for criminal offences are limited and for other offences the laws may impose strict liability - in effect the offender is guilty until proven innocent. Mines may be included under contaminated land legislation, creating additional liabilities for clean-up, rehabilitation and long-term management. It is not unknown in Australia for the value of a mortgaged property to be less than the amount of the environmental liability acquired by a mortgagor in possession due to contamination of the site. An essential part of the management program for resource projects is now the regular conduct of an environmental audit, the results of which assist in the management of the legal and financial liabilities facing company directors and managers. The audit can also assist with negotiations with government agencies, staff, unions, insurers, Aboriginal and other community groups. An environmental audit may also help to ensure that companies are claiming the maximum allowable deductions for environmental works under the tax laws, and provide evidence in support of such claims. Environmental legislation affecting resource industries Environmental legislation in Australia is changing rapidly and can impose massive constraints, substantial administrative costs, and considerable liability on directors, managers and the corporation. Pollution control legislation Every State and Territory of Australia has a range of pollution control legislation contained in either individual acts relating to air, water, noise and land, or embodied in a single environment protection act. Pollution control legislation provides a critical management baseline for resource industries throughout Australia, often requiring the full-time attention of an environmental manager or an environmental department. In general, it is an offence to discharge effluents into water, or emit gases into the atmosphere above prescribed limits, cause noise above a regulated level, or contaminate land without a licence. A licence determines how much of a substance can be discharged, the location, the receiving environment, the quality, and the time at which discharges can be made or noise can be caused. Planning legislation Planning legislation controls where a project is located, how it will be constructed and operated, how large it is allowed to be, and what will happen once the project is completed. Development consents or approvals will generally contain a range of conditions controlling the preparation of the site, the construction of the facility and the way it is operated throughout its expected life time. Resource projects may be regarded under legislation as scheduled or designated developments requiring special treatment during the decision-making process. Under planning legislation, it is usual for resource projects to be subject to an environmental impact assessment process. Resource legislation Resource legislation specifically covering mining and petroleum in Australia, also contains requirements regarding protection of the environment during exploration for and extraction of minerals and oil. A mining or petroleum production lease usually contains numerous conditions regarding protection of the environment and rehabilitation of the site during and after the life of the extractive process.

Jan 1, 1994

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

By K Eglinton

The extractive industries response to community engagement due to social and political pressures in the 1980s and 1990s was the starting point of development leading to the modern function of corporate social responsibility.Challenged by communities who have greater access to information, demand greater transparency and responsibility of corporate organisations and who possess greater awareness of the communities they participate in, the mining sector faces another step change in how it approaches and integrates corporate social responsibility, transparency and engagement.Mining is seeking reserves of lower grades, in more sensitive environments and in countries with minimal transparency and governance. Not only are the locations changing but so to the stakeholders to engage with and issues to contend with. An increasingly savvy opposition, including not just the ‘green hippies’ but the Gen-Ys interested in the wider sustainability debate and Baby Boomers moving to life style environments, are now questioning mining’s behaviour and encroachment into ‘their space’. Issues including effect on lifestyle amenity, property value, energy efficiency, social provision; concepts such as ‘doing more with less’, participatory engagement, increasing transparency and balancing economic, environment, cultural and social aspects are becoming the norm.The traditional model of supporting local communities, communicating plans and providing employment, community investment and indigenous support programs is not enough. Our industry faces challenges on multiple fronts. It must now be able to address these from a personal/community perspective if it is to remain relevant within communities and play a role in addressing the global sustainability issues.This paper draws on corporate social responsibility trends, integrated functions and implementation approaches through the application of activities within Newmont operations across Asia Pacific.The approach presented works on the philosophy that communities do not necessarily have to like what we do, but should be able to identify and recognise the way in which we involve them in decision making, communicate our intentions and respond to issues.

Nov 22, 2011

By D J. Kilkenny

Work practices involved in shaft construction can be aligned with current industry standard operating practices. However, the working environment during conventional shaft construction introduces unique conditions which can not always be overcome by hard engineering controls. To provide an improved working environment, future shaft diameters will generally be greater than has historically been the case for the Australian hard rock mining industry. This paper aims to explore both what can be constructed from the contractors perspective, and how does an owner extract maximum business efficiency from an asset that in many ways is likely to be larger, more complex and more expensive than initially envisaged.Newcrest Mining Limited, or an associated company, has constructed two major shafts over the last seven years. In both cases, Byrnecut Mining, or an associated company, was the contractor engaged for the shaft sinking activity. The first is the 1127 m deep, 7.0 m diameter production and intake airway at the Telfer Gold Mine, the second is a 295 m deep, 5.5 m diameter split shaft at the Gosowong Gold Project in Indonesia that was primarily designed as both an intake and exhaust airway. Importantly both shafts are designed to provide emergency egress from the respective underground operations.From an Australian shaft sinking perspective, the construction of these two shafts resulted in the following learnings: •constructability is of equal importance to desired functionality;•allow six months of interactive design between the owner/engineer/contractor/regulator to get it right;•shaft sinking and equipping are intimately entwined, therefore engineering of both needs to be complete prior to any activity commencing; and•the mobilisation of both equipment and experienced personnel to a new shaft sink takes up to eight months.Shaft sinking is not extinct in the Australian hard rock mining industry. But, if you are considering constructing a shaft, approach it as a long life asset, front end planning to a high level of detail is required to unlock its full value. Think – plan – think and remember it’s going to take 12 months to get from the whiteboard to firing the first cut.

Mar 21, 2011

By L Keeney

Cu-Au porphyry deposits are large tonnage low-grade resources dependent on processing large volumes of material. The ability to understand and predict comminution performance is critical, as it is frequently the rate-limiting step during processing. Parameters required from geometallurgical mapping and modelling of comminution performance are: A×b processing domains based on impact breakage variability, and BMWi processing domains showing grind response variability which lead to Mine throughput domains for a specific comminution circuit configuration. Due to the cost and/or large sample requirements of traditional comminution tests, insufficient data density and distribution of comminution indices commonly exist, making it difficult to model and map deposit scale variability. One method routinely applied to three dimensional domaining is to have an a priori zoning based on geological features (lithology, alteration, mineralogy, textures), and then apply to all material within a given domain the metallurgical values measured on a single sample or average of samples from that domain. The problem with this approach is that commonly the geological domains do not reflect comminution response, therefore compromising the quality of the average domain estimate. To resolve this problem an alternate integrated geometallurgical mapping and modelling method is applied to model and map comminution performance at Cadia East. This paper uses a data set of ~32 000 assay measurements and geological logging information, integrated with ~150 comminution measurements to analyse and develop proxy support models for comminution indices (ie A×b, BMWi, and throughput) based on inherent geological variability. Discrete downhole comminution processing domains are created, mapping orebody response while maintaining inherent variability.

Sep 5, 2011

By E Widzyk-Capehart

The mines of the future can be envisioned as complex, large-scale technological systems being operated remotely from few centrally located (major cities) operating centres and skeletal crew stationed at the site. These systems will require remotely located human operators to constantly adapt to new and unforeseen system and environmental demands. In addition, the remote operators will need to match system properties to the changing demands and operational conditions, ie must be able to handle the ‘non-design’ emergencies, because the system designers would not have been able to foresee all possible scenarios of failures and provide automatic safety devices for every contingency. Therefore, it is highly important that the operators’ job, which involves problem solving and decision making at the workstation level, is facilitated by the proper interface designs. This paper argues that decision support systems and thus human-system interfaces for the mines of the future should be developed based on the principles of human-system integration that take into account human information processing and cognitive abilities. The information presented to the operator must support the operator in taking appropriate action through a human-system interface designed according to scientific principles of User Centred Design. A case study is presented where an iterative design process was used by CSIRO researchers as an evaluation method involving users (control room operators) at several stages of the user interface design in order to correct any design inadequacies as they emerged. This process allowed the designers to identify any usability issues before the user interface was fully implemented, which subsequently enabled the control room operators to easily adapt to the new interface and carry out all designated tasks in a timely and effective manner.

Nov 22, 2011

By S Leichliter

La Colosa, Colombia is a large gold-porphyry deposit currently undergoing feasibility studies by AngloGold Ashanti. This period of development allows the opportunity to apply innovative and emerging testing and modelling methods to provide a predictive geometallurgical recovery model for the deposit. By partnering with the AMIRA P843A Geometallurgical Mapping and Mine Modelling (GeMIII) research project, the geological and mineralogical data are analysed with respect to liberation and recovery methods. This will allow the variability in the geology and mineralogy of the deposit and key relationships recognised in the data to be included in the development of a model to help predict recoveries of the gold. Many aspects of the gold mineralisation such as gold paragenesis, associations, grain size and texture are determined and analysed using optical microscopy, Mineral Liberation Analysis (MLA), and laser ablation (LA-ICP-MS). At La Colosa the gold has been located in sulfides (eg pyrite, pyrrhotite, and chalcopyrite), silicates, along silicate phase boundaries, and among the pyrite-rich intermediate argillic alteration. Further testing and analysis will also determine if ‘invisible’ gold is present in the pyrite, pyrrhotite, and chalcopyrite. Recovery methods can also be determined and tested after combining the results of mineralogy tests with other data (eg results of comminution tests). Indices for the mineralisation and recovery are developed using image analysis and analytical testing. These indices are correlated with recovery data from the company to develop a predictive block model for recovery. The goal is to develop cost-effective, efficient methods to analyse the mineralogy and geology of the deposit; understand the variability in the mineralogy, geology, and recovery; and construct a predictive geometallurgical recovery model.

Sep 5, 2011

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By J Lombardi

OZ Minerals' Prominent Hill copper-gold concentrator is located 130 kilometres south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for eighteen cells.Generic proportional – integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Aug 8, 2011