Search Documents

By S G. Keyte

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.l mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass Yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80 per cent and mass yields of less than one per cent can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

A process was developed to produce electrolytic manganese dioxide, suitable for use in high quality dry cells, from Risdon anode mud. ImpurItIes present In the anode mud were removed prior to the electrolysis which was performed from a manganese sulphate bath using the following conditions.Temp. 95°CH2S04 50-55 g/l.Mn2+ 55-60 g/l.Anode c.d. 10·0 A/sq. ft.Operation under these conditions yielded current efficiency and power consumption figures of 95 per cent and 0·8 kWh/lb respectively. The product conformed to battery manufacturers' specifications as regards physical and chemical properties and performed satisfactorily in a battery testing programme.

Jan 1, 1968

The Fraser Range is composed dominantly of basic pyroxene granulites derived from basalts, many of which appear to have been vesicular and pillowed. Acidic and basic garnet-bearing granulites are important in the west, and acidic granulites and narrow anorthosite layers are dominant in some regions east of the Fraser Range. An extensive flat-lying olivine gabbro sheet cuts the granulites, and in places has been converted to spineI-bearingmeta-gabbros and pyroxene granulites. The granulites of the Fraser Range (Proterozoic) are separated from the gneisses and schists of the goldfields regions (Archaean) by the Fraser Fault, over which there is a large gravity anomaly (gradient 20 milligals per mile). Some of the problems associated with the concentration of Cu, and Ni liberated from mineral lattices during metamorphism, and other principles of metal concentration in granulite terranes, are discussed. The recognition of vesicular and pillowed zones, even though highly metamorphosed, is of fundamental importance.

Jan 1, 1969

By Stewart WJ

Australia's first offshsore well was spudded in on 27th December 1964 and resulted in the discovery of the Barracouta gas field. Further exploratory drilling led to the discovery of the Marlin gas field in December 1965, the Kingfish oil field in April 1967 and the Hblibut oil field in June. 1967. In September 1968, a small oil reservoir was found in a sand below the main Barracouta'gas reservoir. The Snapper gas field was discovered in May, 1968 Information on exploration activities associated with the discovery of oil and gas in the Bass Strait area may be found in the paper, "Exploration in the Gippsland, Bass and Otway Basins, Australia" by B. M. Hopkins. _ Development of the commercial fields is being undertaken on an equal participation basis by Hematite Petroleum Pty. Ltd. and Esso Exploration and Production Australia Inc. Esso Standard Oil (Australia) Ltd. is responsible for the design, construction and operation of the production facilities.

Jan 1, 1970

By B Murphy, A Uliana, P STrgio de Oliveira, G Ara·jo de Souza Franco, T Miettinen

Outotec has performed numerous research and development projects and various surveys in the study of reverse iron ore flotation. Over the past four years their TankCell-70 and TankCell-160 flotation cells at the Germano concentrator of Samarco in Brazil were extensively surveyed. These surveys have revealed some extreme operating conditions in reverse iron ore flotation and are the subject of this paper. Some of the findings include large variations in the content of solids in the various flotation stages. At the bottom of the cleaner cells, the content of solids by weight reached over 60 per cent, whereas at the bottom of the scavenger cell this was less than 50 per cent. Froth carry rates were also significantly different in the various flotation stages. In the case of coarse material, the scavenger cells operated at a froth carry rate of over 40 t/h.m2. With fine material, however, froth carry rates of less than 10 t/h.m2 were measured. High froth carry rates caused significant changes in the residence times at Samarco. In the rougher cells, the fifth cell had more than double the residence time of the first cell. This was even more pronounced with the scavenger cells, where the second cell had more than triple the residence time of the first cell. High froth carry rates also caused losses in iron recovery. As a consequence of such findings, it appears that different rules apply in the sizing of reverse flotation circuits compared to direct flotation circuits. Different operating parameters (mixing intensities and air flow rates) must also be used in the rougher, cleaner and scavenger cells in order to optimise the metallurgical performance. Outotec has also been working on a number of new technologies aimed at improving the metallurgical performance of iron ore reverse flotation circuits by increasing froth carry rate and decreasing fine iron entrainment.CITATION:Miettinen, T, Uliana, A, Ara·jo de Souza Franco, G, STrgio de Oliveira, P and Murphy, B, 2013. TankCell flotation at SamarcoÆs Germano concentrators, in Proceedings Iron Ore 2013 , pp 441-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

The Wainui Mill was conceived as a 60 - 90 t/d central mill to process gold ores of the Thames area of New Zealand from small mines in the district. The ores of the region exhibit various degrees of refractory response to conventional cyanidation leach due to the fineness of the gold, and association with pyrite. The alternative circuits involving cyanidation, flotation, and possible small-scale smelting are examined. The environmental impacts have been audited by the Commission for the Environment and were found to be acceptable.

Jan 1, 1986

Procedures employing thiocyanate and dithiol complexes of molybdenum have been developed for the determination of the metal in the presence of large quantities of ferric iron. The procedures are developed for field application and it is possible to complete 200 analyses per day with laboratory accuracy. Use is made of sulphuric acid extraction and ascorbic acid reduction in the case of the thiocyanate procedure whilst the reducing system in the dithiol procedure is potassium iodide-sodium sulphite. Using a simple photometer the range of determination possible is 0-10~g for the thiocyanate procedure and 0-5 g for dithioI.INTRODUCTIONOf the many colorimetric procedures that have been developed for the determination of molybdenum only those using the thiocyanate or toluene-3, 4-dithiol complexes of the metal are sufficiently free from interference to be of use in geochemical prospecting. Rapid methods based on both these complexes 'have been developed at the. Broken Hill Division of The University of New South Wales as part of a general programme designed to improve geochemical procedures. Whilst speed rather than high accuracy is the important factor in prospecting, the aim of the programme is to develop procedures which will allow determination of 200· samples per man-day without loss of normal laboratory accuracy for the methods concerned.In most geochemical procedures visual estimation of a coloured complex is used in the determination of the quantity of metal present. At the high rate of sample determination of the improved methods this procedure places severe strain on the eyes. For this reason all methods are designed for determination by means of a simple filter photometer...

Jan 1, 1965

By A Duran

When dealing with rocks in the geotechnical profession, a common activity involves providing an estimate of the intact strength. The tactile approach and descriptions of strength that apply to soils is well documented, can be readily checked through the use of a pocket penetrometer and are known to provide reliable estimates of strength. Moreover, although different soil strength classification systems are present, the bounds between classification classes are compatible across almost all documented classification systems. However, this is not the case for rock strength materials. There are numerous systems within the literature, some with different concepts, and almost all have different bounds to each strength classification. In this paper, the author presents seven classification systems for estimating intact rock strength and highlights issues in their implementation. Example cases are presented to discuss the typical concerns confronting field strength estimates.CITATION:Duran, A, 2014. Comparison of field estimated strengths, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 101–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By N Lewis

Recent major urban trunk sewer infrastructure projects in Melbourne have involved construction of nearly 10 km of tunnel boring machine (TBM) driven tunnels in a range of geological conditions varying from soft alluvial soils to hard volcanic rock. To provide both construction and permanent access to the new trunk sewer network, a total of 17 shafts between 5 m and 13 m in diameter, and up to 64 m in depth have been constructed. This paper describes the design and construction of the temporary shaft support systems for the shafts.The range and variability of geological conditions at each shaft site required the adoption of the following shaft support systems across the projects – jet grouting, sheet piles, diaphragm wall, secant pile, contiguous pile, reinforced shotcrete rings and rock bolts.Groundwater control, settlement, TBM launch and reception chambers at the shaft base, chambers and TBM launches at mid-depth of shafts, connection shafts between new and existing sewers and bypass pumping shafts are among the challenges that have been met.This paper reports on the some of the challenges involved and experience gained in developing design and construction solutions for large diameter shafts that are excavated within varying geology in Melbourne over the past three years.

Mar 8, 2011

This paper gives a general description of mining operations at the Mount Morgan Open Cut. Certain features such as blast hole diamond drilling, which may be of particular interest, have been described in detail. The paper is covered by the following headings:-1. History2. Ore Reserves and Production Data3. Mining Methodsa. Design and Layout of the Open Cut.b. Overburden and Ore Breaking.c. Loading and Transport of Ore and Overburden.d. Transport of Men and Supplies.e. Survey and Assay.f. Drainage.4. Power and Compressed Air5. Mining Equipmenta. Shovels.b. Mine Transport.c. Dozer Tractors.d. Drill Shop.6. CostsHISTORYIn order to appreciate fully the design of the present Open Cut at Mount Morgan, a brief outline of the Mine's history and past mining methods is necessary. In 1882 the Mount Morgan Syndicate began to mine this large gold-copper orebody by small hill-top quarries...

Jan 1, 1952

Currently in Canada there are 15 major mining companies with a minimum of $1 billion in market capitalization or net private value. This group forms the core of an important sector for Canada. The mining sector had gross revenues of about $35 billion in 1988. This compares to a Canadian GDP of $410 billion in 1988. There are at least three different sub-groups within the mining group, each facing the future with very different prospects for the coming years.

Jan 1, 1989

By H Peiming, W Sakurai, Y Matsuhisa, H Shimazaki, Y Fukahori

Oxygen and carbon isotope mapping of hydrothermally altered wall rocks was applied to the blind ore prospecting of skarn Pb-Zn deposits in the Kamioka mining district, centralJapan, where the wall rocks consist of heterogeneous rock units. The results (d18OSMOW of -1.1 to +17.3ë and d13CPDB of -5.0 to +4.8ë for limestones, and d18OSMOW of -0.8 to +12.5ë for silicate rocks) show isotope zonations of the wall rocks with depletions in heavy isotopes (18O and 13C) toward the centre of mineralization. The isotope zonations likely formed by interaction of migrating thermal waters with the wall rocks during the mineralisation. The heavy-isotope depleted zone, which indicates higher temperature or higher water-to-rock ratio of the system, occurs in the footwall of a fault, indicating that the fault played the role of main conduit of the ore-forming fluids. A heavy-isotope depleted zone was also found in an area, where significant mineralisation had yet to be identified. Recent drilling in this area has intercepted a zone with a grade of 16.0% Zn, 0.8% Pb, and 35g Ag per metric tonne at a depth of about 360 m.

Jan 1, 1995

By S Christensen

In August 2001 the Minister for Conservation declined an application by GRD Macraes for an access arrangement to enable work at the Globe Progress Mine near Reefton. In her decision, Ms Lee said:æI have considered whether potential compensation and the proposed safeguards against some of the adverse effects are sufficient to outweigh my concerns as to the loss of conservation values, consistency with the objectives of the Conservation Act, the purposes for which the land is held by the Crown and, to a lesser extent, the North Westland Regional Management Plan. I do not think they are sufficient. To my mind, my concerns as to the consistency with the objectives of the Conservation Act, the purposes for which the land is held and the loss of some conservation values in particular, outweigh any potential compensation and possible mitigation of adverse effects.Æ Commenting on the MinisterÆs decision Guy Salmon of the Ecological Foundation stated that the Minister should have invited the applicant to provide a 10 000 hectare pest-free wildlife sanctuary as part of the æpriceÆ for obtaining that access. However,æfor many people of green persuasion, it has become fashionable to say no every timeàthose who really have the well-being of the environment at heart, will want to look carefully at the bigger picture of environmental restoration needsàThe deciding criterion: the mining company should show that its involvement on conservation land would produce a net conservation gain. That is a criterion that creates the right incentives for win-win-win solutions on conservation land.ÆThis paper considers whether the concept of off site mitigation is one which fits within the current legal regime. Two questions arise:Can such mitigation/compensation be legally considered in access arrangements or required as a condition of resource consents? Is this a realistic option for industry to be pursuing?

Jan 1, 2002

Forecasting, particularly when applied to meaningful issues, is known irreverently as 'futurology'. There is quite a range of opinion ext.ant in the world when mineral resources are looked at. The opinions range from the doomsday view that there will be acute shortages of all essential commodities, to the optimistic outlook that new 'discoveries will prevent any possibility of shortages. The environment is, as yet, only studied locally and quite parochially; surprisingly there is little integration when considering the spatial atmosphere, the seas in depth and the earth's crust.

Jan 1, 1981

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Waters CA, Happ JV

The debismuthising plant, commissioned in 1980, is based on the Kroll-Betterton process for preliminary bismuth removal with subsequent antimony treatment for fine debismuthising. Bullion flowrate is continuous and the plant was designed to achieve low bismuth lead product at rates of up to 20 tonne/h.Development of the first stage of the operation has enabled reliable operations at 25 tonne/h to be achieved. Thesedevelopments also introduced the opportunity to treat higher bismuth bullion at up to 35 tonne/h when operating the first stage only to produce product lead of 0.029 per cent Bi, meeting the ASTM B29-55 Corroding Lead Standard.

Jan 1, 1985

By B M. H Sharp, R P. Hide, S P. Devine

Uncertainty and debate currently pervade the mining industry in New Zealand. The operational uncertainties, whether external (eg gold prices, the exchange rate), or internal (eg coal expansion difficulties), are large. In addition, many wider factors which influence mining are in a state of flux. State Coal Mines, the operating branch of the Mines Division of the Ministry of Energy I may be made a state corporation, with the remaining Mines Division functions being revamped. The agencies administering environmental legislation are to be restructured. Mining legislation amendments have been proposed and then dropped, and the area is now to be reviewed (The Press, 31 July 1985). Some mining licences have been withdrawn, and become the subject of heated debate in the community (The Press, 19 July 1985, and subsequent letters to the editor).

Jan 1, 1985

By B M. Guerin

In this paper, some of the constraints to applying bioremediation to the decontamination of polluted soils are introduced. Particularly, attention has been given to those associated with the geology of the polluted site. Areas which require further research have been addressed and indicate that geologists will play a key role, alongside microbial ecologists and engineers, in designing and implementing bioremediation strategies.

Jan 1, 1992