Search Documents

By W A. Peck

Raise boring is the preferred option for constructing ventilation shafts in Australia. The trend has been towards larger diameters and longer single-pass shafts, and if at all possible, reaming through to the surface. The risk of raise failures, due to missed, unforseen or latent ground conditions has therefore been increasing, along with the need for better, more confident stability assessments.While the stability of specific weak zones and structures must be assessed individually, empirical rock mass classification schemes have been successfully used for about the last 20 years to assess general raise stability; eg the McCracken and Stacey method (M&S).Unfortunately M&S, as originally documented in McCracken and Stacey (1989), did not include a database of raise diameter and rock mass conditions versus actual performance. Nor was there a procedure for assessing the risk of failure due to adverse ground conditions. Peck and Lee (2008) published an Australian database of raise bore performance. Raise diameter and ground conditions, in terms of a lower bound Qr value, were presented for 50 cases versus raise performance. This paper updates the 2008 raise performance plot with more and SRF-corrected data. McCracken and Stacey (1989) had previously recommended that additional geotechnical data should be acquired and analysed when the proposed raise plotted on the unstable side of raisebore stability ratio (RSR) = 1.3, but the Australian data used in this study also suggests that all sites with Qr Contributions and sensitivities of various rock mass parameters (RQD, Jn, Ja, Jr, Jw, SRF, time-dependent weathering/deterioration) to raise stability and risk of failure are discussed. Numerous case studies are used to illustrate issues with stability assessments.As raises can now be remotely supported using sprayed fibrecrete, questions of time-dependency are also discussed. In recent times, contiguous piles, ‘mini-piles’ and grouting have also been successfully used to presupport or otherwise improve the stability of near-surface sections of weathered, or poor quality rock masses.

Mar 21, 2011

By T D. H McGrath, J P. Vaughan, J Heath, J J. Eksteen

A reliable laboratory method to characterise the response of free gold particles when subjected to flash flotation conditions has been developed by AMIRA P420 researchers at Curtin University. This test has been applied to assess the flotation recovery of gravity recoverable gold from free milling ores as well as synthetic ores featuring either a gravity concentrate or gold powder. Trends in free gold flotation kinetics as well as size and milling effects were identified for gold recovery, based on the different gold types, reagent dosage and residence time.CITATION:McGrath, T D H, Eksteen, J J, Vaughan, J P and Heath, J, 2013. Laboratory flash flotation trends for a variety of gold particles, in Proceedings World Gold 2013 , pp 357-366 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By L Nienaber

Mines, after becoming operational, often retain the same support and reinforcement designs developed in the feasibility study. These designs are conceived from limited drilling data and regional experience, thus having an empirical flavour. Empirical designs are perceived to be conservative, catering for a variety of failure mechanisms, which are not always present in mine development drives.This begs the question: If you were to invest in the necessary resources to obtain sufficient data and complete the required analyses for the different development drives in the mine, to engineer a support and reinforcement scheme with the capacity to match the demand of the rock mass, what is the difference in cost when comparing an empirical design to an engineered design?To answer this question, mine tunnels with different geometries and orientations, where detailed structural data was available, were selected for a comparative design exercise. Material cost, development cost, cycle time and professional fees for engineered and empirical designs were estimated. The outcome is summarised in the following paper that discusses the process followed and the results of the design comparison.

Mar 8, 2011

By Yanske TR, Lane WL

The Doc Run Company and its predecessors have been mining for over 130 years utilising the room and pillar mining method. This method has left approximately 20 per cent of the orebody in the remaining pillars. The original design and planning for the mines did not include extensive pillar extraction. This paper summarises the introduction of the pillar extraction and backfill techniques which have been implemented since 1991. These techniques include the use of low cost fill walls up to 20 in in height and the use of stinger trucks for topping off the fill. In conjunction with these accomplishments, much experience and confidence has been gained in the use of numerical modelling as a method of predicting pillar stability as the mining of pillars progresses. These advances have led to pillar extraction hecoming a major portion of the overall production and have added to the mine life of Doe Run's six operating mines.

Jan 1, 1998

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By M Szwec, P Corbett, P Sheffield

Centennial Coal operates the Springvale and Angus Place longwall mining operations that extract coal beneath the Newnes Plateau in the Western Coalfields of New South Wales. Springvale and Angus Place mines have a history of difficult geotechnical conditions, where mining operations are conducted with a thick coal roof interbedded with numerous claystone units and relatively high levels of vertical and horizontal stress. The combination of a relatively high stress regime and weak laminated roof has led to numerous roof failures throughout the mine’s life.Following underground roadway development, the mine roadways can experience high levels of roof movement that can lead to roof falls. Two-point wire extensometers (known as ‘telltales’) are extensively used for roadway condition monitoring. Along with extensive other geological and geotechnical data, monitoring data is used to prepare geotechnical hazard plans that are then used in all areas of mine planning to allow for safe and efficient operation of the mine.This paper presents a case study of the use of a new software tool that allows time-scaled visualisation of monitoring data in the context of longwall and development face positions and installed strata support. It can be used in the identification of geotechnical risk factors and their interaction with the mining process to allow a more robust geotechnical hazard process. It interfaces directly with the widely used ExtoChart database software and can be presented with scale drawings of geological/geotechnical data to allow correlation of monitoring data with risk factors.CITATION:Corbett, P, Sheffield, P and Szwec, M, 2014. A new tool for extensometer data analysis and improved understanding of geotechnical risk factors, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 217–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

In practice a sampling solution is a compromise of many requirements: the sample should be representative; the sampling system should also be reliable, less than 95 per cent availability restricts the use of the assayed sample for process control purposes; no sample is the worst sample, and investment costs and installation space/layout are frequently a restriction. For instance, online X-ray analysers for process control introduce a delimitation error by the nature of X-ray physics. Thus only in special cases a relative accuracy better than three per cent relative, as one standard deviation, is achieved. A sampling system for process control needs not to be, as representative, for so many sample properties, as one for composite laboratory analysis samples. Sampling system maintenance is also an important issue. There are many sampling systems in the industry which have been difficult to maintain and are in disuse for lack of resources or incentives to keep them running. Pierre Gy developed the most generally accepted sampling theory. One of the main principles is that all particles in a one-dimensional process stream should have equal chances of being included into the sample. A correctly designed and operated transversing cutter comes close to this goal but has limitations in temporal representativity. For slurries an acceptable solution in many cases is to use a fixed vertical cutter(s) in a position where the slurry is well-mixed by turbulence and other means. For online analysis, reliability problems are mostly related to faulty design or installation of the piping system to the analyser. Properties of material processed, process flow sheet and piping details before and after the sampler have to be taken into account when deciding on which sampling arrangement is appropriate. Guidelines and some solutions to these issues are presented in this paper.

Mar 1, 2010

By T Day, I G. Robertson, G J. Lyman

"Various approaches are used in the industry for establishing procedures (sample mass estimation and method of subsampling) for sampling and analysis of gold ores. The key factors that determine the accuracy of the results that can be expected for a given set of procedures are widely misunderstood.Recent developments in sampling theory show that the estimation of the accuracy that can be expected for a given gold ore as a function of sample mass is actually a simple matter. For a given sample mass, the accuracy that will be achieved depends only on the grade of the ore and the range of masses of the grains of the gold in the ore. This, of course, demands that a reasonable estimate of the distribution or spread of gold grain masses in the ore be known. But this is something that should be known if the gold is to be efficiently recovered in the processing plant.This paper provides a simple explanation of the real facts about sampling of gold, either in the field or in the plant, and provides results for a number of cases of combinations of fine and coarse gold in an ore. The prerequisites for accurate gold sampling are:correct sampling with no loss of sample or contaminationsample preparation procedures that recognise the impact of the gold grain mass spreadpractical analysis of the sample masses required to provide acceptable accuracy.Issues of corporate governance are also discussed.Citation:Lyman, G J, Robertson, I G and Day, T, 2016. The Simple Facts about Sampling Gold Ores, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 159–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By K Rees

In the ideal world of an underground mining engineer, all narrow vein orebodies would be perfectly straight and continuous, thus would be a dream to mine. However, this is usually not the case. Narrow vein orebodies generally occur in association with shear zones and while shear zones do form linear trends, they most commonly preserve undulating expressions that need to be closely monitored, particularly when overprinted by post-formed structures. The surge in mines using fibrecrete as a primary form of ground support effectively reduces the time available for geological interpretation down to a 30 minute window between bogging and shotcreting. Thus, if the quality of the data collected is not up to scratch, then there is only a limited ability to reassess using 2D face photographs. To negate this, Xstrata Nickel AustralasiaÆs Cosmos mine has upgraded its data collection procedure. Geological information is now collected using photogrammetry survey, producing 3D images of the drive. Once created, the digital image of the drive is loaded into Vulcan, thus enabling geological interpretation to be carried out along entire drives, between levels and in association with all other data (eg drill holes, seismic data, etc). In addition to this, the 3D image can be used to accurately model the location of the ore, enabling stoping panels to be confidently positioned to maximise grade and minimise dilution. However, with the focus at Cosmos changing from narrow vein mining, to bulk mining methods in a more geotechnically complex terrain, the use of the 3D images has become paramount in understanding the structural geometry. Continual interpretation of the data has enabled drive profiles to be maintained through the increased use of ground support in poor ground and the redesign of development to enable optimal intersection of structures. Nevertheless, while the collection of quality data is important, it is only the effective use of the data, which enables significant gains in understanding.CITATION:Rees, K, 2012. The benefits of using photogrammetry in the geological interpretation of the Cosmos nickel mine, in Proceedings Narrow Vein Mining 2012 , pp 145-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By Jankola W. A, Delong O. J

Historically, the silica content of zinc concentrates treated at Cominco's Trail Operations has been low. Silica in the roaster calcine seldom exceeded 1.5 per cent because of the low silica content of concentrate from Cominco's Pine Point mine. With the shutdown of Pine Point, alternate sources of concentrate were required and it was anticipated that calcines containing greater than two per cent silica (with excursions above three per cent) would have to be treated. Previous experience indicated that the existing leaching circuit could not tolerate such high levels. Therefore, a research program was undertaken to identify the key factors affecting silica precipitation; to compare different process alternatives; and to make recommendations for modifications to the existing plant. A project to modify and upgrade the leaching circuit has now been completed. Calcines with higher silica contents are successfully treated, but the upper limit of the circuit is unknown. The results of the research work will be discussed and the new leaching plant will be described. Recent operating results will also be presented.

Jan 1, 1993

By J Joy, A Bye, G V. Kizil

This paper demonstrates an application of a recently developed Risk-Cost-Benefit (RCB) Framework to environmental risk management in the mining industry. The environmental application of the RCB Framework as part of an ACARP project (Kizil, Bye and Joy, 2012) involved a thorough selection process with site visits and in-depth discussions with the case study siteÆs environmental management team. Under their guidance, the highest risk of environmental impact at the case study site was identified as æroad subsidenceÆ at the time when the project work was undertaken. This paper presents the unique application of the RCB Framework to examine the risk of mining-induced subsidence and its impact on one of AustraliaÆs busiest highways, with a traffic volume of 38 000 vehicles per day (NSW RTA AADT, 2008). The RCB Framework was employed to assess the optimum group of controls for road subsidence risk management to ensure highway availability while mining occurs. Whilst this paper focuses on road subsidence, the methodology employed can be directly applied to other environmental concerns including preparation for mine closure, rehabilitation planning and waste management. The RCB Framework incorporates mathematical modules which were developed to enable complex yet tightly integrated RCB calculations. The process integrates the risk-control effectiveness assessment to determine that the selected safety initiative is financially beneficial to the mine site and company. This concept has been applied to a number of high-risk mining areas targeting safety, productivity and environmental issues. This paper introduces the five-staged RCB Framework, incorporating the RCB tools RCBGEN (Risk-Cost-Benefit Generator) and RCEMETHOD (Risk-Control-Effectiveness Method), and demonstrates its practical application to the risk management of a road subsidence case study. The case study looks at potential pavement damages, in particular, the occurrence of pavement stepping on the surface of the highway as a result of vertical subsidence. This type of road damage was previously experienced at another major inter-city route while underground mining occurred in the region where the case study site is located. The RCB Framework has been successfully applied to the analysis of the road subsidence case study and determined the risk reduction and financial benefits of implementing a range of risk-controls. User-friendly RCB Charts to provide an aid for decision-making were produced. The value of using the RCB charts to achieve balance between risk, cost and productivity in the decision-making process for risk management has been explained. The case study determined that pavement slots and fibre-optic cable monitoring were relatively low-cost and effective controls applied in the mining industry for the first time at a global level.This paper supports the industryÆs ongoing efforts to manage risk to ALARP (as low as reasonably practicable) and achieve æzero harmÆ by providing a new Framework to more effectively establish the adequacy of controls.CITATION:Kizil, G V, Bye, A and Joy, J, 2012. Application of risk-cost-benefit analysis to highway subsidence due to mining, in Proceedings Life-of-Mine 2012 , pp 197-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C McCamley

"The requisite for maintaining optimal carbon concentration levels in a carbon-in-leach (CIL) circuit is of paramount importance in the prevention of gold losses. The process’s ability to recover gold from the aqueous phase is primarily dependent on the carbon loading profile of the CIL train.Newmont Boddington Gold (NBG) have over 2015 tested the Mintek online carbon concentration wmeter (C2 Meter) suitability for effective carbon concentration measurements in their CIL circuit compared to the standard method where the readings are taken twice a shift by the operations staff. The C2 meter works by passing a 1MHz ultrasonic signal through a slurry containing carbon where there is a relationship between the carbon concentration and the attenuation of that signal.It also highlighted another area where the C2 meter could be implemented at NBG whereby the instrument can be as a cautionary device for carbon losses in place of carbon safety screens.Citation:McCamley, C, 2016. Continuous Carbon Concentration Measurement at Newmont Boddington Gold, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 207–212 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Casas Castellanos

"Tyres consumption is one of the costliest branches of the operation in a truck-based haulage mine. Off-the-road (OTR) tyres working within undesirable conditions have a considerable negative impact on the whole mine’s productivity. Only the rolling resistance due to underinflated tyres could increase truck fuel consumption by 15 per cent. The impact of other conditions such as road surface quality and temperature are difficult to estimate. Tyre management is a demanding activity that requires a high level of coordination between maintenance and production departments.The project is aimed to develop a smart decision tool to assist mine managers to optimise tyre resources. By identifying factors that have significant impact on tyres, managers are able to take timely action to mitigate undesirable working conditions.The proposed model utilises real-time tyre measurement of pressure, temperature, speed, load, deformation and surface profile to report tyre performance in terms of tonne-kilometre-per-hour (TKPH) and tyre longevity. Both indicators are permanently monitored in order to trigger a warning system designed to keep tyres under optimal working conditions.An interactive database ‘Octo-Mine’ wirelessly receives records from a programmable logic controller (PLC) deployed on the truck. PLC records are the integration of multiple sensor signals with a time stamp. Octo-Mine utilises real-time and historical tyre records to generate online performance and longevity reports, as well as preventative and corrective tyre maintenance scheduling, by comparing current tyre status with established standards.To validate the model, the prototype database was populated with hypothetical data to simulate ideal working conditions subject to comparison with real field observations. Additionally, a laser-based technology prototype device successfully measured a new 9 mm tyre tread and a 60 000 km rolled tyre tread in the laboratory.In conclusion, optimal tyre management contributes not only to reduction of tyre waste but also to truck energy efficiency. This project is a first step in proving these benefits under real field conditions. It suggests that further development of sensor equipment and its integration with a communication system is a worthwhile focus for future research.Citation:Casas Castellanos, S, 2016. Optimum Management of Truck Tyres in a Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 212–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By A E. Annels, G F. Johansen, B W. Cuffley

Nuggety gold-quartz reefs are characterised by localised, high-grades and in many cases coarse free-gold. Geometrical and grade complexities are often observed. The high-grade regions are generally erratic and have a low continuity; though may make the deposit economic. Viable grades are generally contained within discrete oreshoots, which are surrounded by barren/low-grade material. Drilling is an effective measure of geological continuity, however grade distribution can only be reliably obtained from underground development and bulk sampling. In general terms, only an inferred resource is likely to be estimated from surface drill data alone. Underground development, further drilling and probably bulk sampling will be required to delineate inferred and indicated resources. Closely spaced development with bulk sampling is likely to be the best way to determine a probable reserve. The resource evaluation process must driven by a clear geological model that should attempt to understand the controls to reef geometry and grade distribution. Geological interpretation has traditionally been undertaken in two-dimensions, though computer software is now being used to produce three-dimensional models. Grade interpolation has generally been undertaken using classical methods, typically weighted averages, zone of influence weighting and polygonal/sectional blocks. Tonnages can generally be calculated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because of its highly erratic and discontinuous nature. To account for variability it is recommended that a best estimate be reported within a grade range, as this more accurately reflects the uncertainties involved. Reporting should be undertaken within the framework of the JORC code, but should involve special consideration of grade reliability.

Jan 1, 2000

By M Olsson, U Nyberg, K Widenberg, P Svedensten, F Ouchterlony

During 2007 and 2008, the project Optimal Fragmentation in Blasting II was conducted at the Långåsen quarry of NCC Roads AB near Arlanda. The main goals were:an evaluation of the effect of using electronic delay detonators (EDDs) in quarry blastinga validation of the design curve concept introduced at the Vändle quarry.Five production blasts were monitored. After a first trial round, the remaining four rounds each had about 100 Ø89 mm holes in a 14–19 m high bench charged with site mixed emulsions. In rounds 1 and 2, a tighter pattern than normal was used in one half of the rounds, raising the specific charge there from 0.7 to 1.0 kg/m3. Non-electric initiation was used with two holes per 25 ms delay in-row and 67 ms between rows. In rounds 3 and 4, electronic delay detonators were used instead, with 10 and 5 ms in-row delays respectively.The monitoring encompassed drill hole collaring and alignment, in-hole deviations, the rock structure in the bench faces from 3D imaging, first row burdens, etc. Eleven 400 t samples were taken from the muck piles and sorted in the quarry and sieved in the laboratory (lab). The lab data made up a fines tail that was grafted onto the in-pit sorting data to form sieving curves for the test piles. These curves were then compensated for the absence of boulders to construct the sieving curves for the blasted muck pile.These have been used to derive fragmentation model formulas for the non-electric rounds, also called design formulas. They are based on blast geometry, charging data and the properties of the rock mass. The formulas may be used to estimate the effect of changing blasthole pattern, borehole diameter and stemming length for example.The use of EDDs gave several unexpected results. In comparison with non-electric initiated rounds with a somewhat lower specific charge the fragmentation was much coarser; x50 increased from 160 to 200 mm. The effect of raising the specific charge in the non-electric initiated rounds from 0.72 to 0.99 kg/m3 was a much finer fragmentation; x50 decreased from 160 to 120 mm.CITATION:Ouchterlony, F, Nyberg, U, Olsson, M, Widenberg, K and Svedensten, P, 2015. Effects of specific charge and electronic delay detonators on fragmentation in an aggregate quarry – building fragmentation model design curves, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 727–740 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Domotor

Brisbane’s Airport Link is Australia’s largest road infrastructure project, worth a total value of A$4.8 billion. The project is using surface and underground blasting to excavate hard volcanic rock, Brisbane Tuff. This paper tells the story of the most challenging and difficult blast of the whole project: the removal of a remnant pillar of rock (approximately 2250 m3) next to a major arterial road and within 100 m of existing infrastructure including a number of heritage listed buildings, residences and privately owned sensitive receivers. The pillar consisted of a hard rock wall (Brisbane Tuff) between 2 m and 6 m thick, 15 m high and 35 m wide; with in situ precast concrete piles embedded within 1 m of the boundary of the pillar. Orica Australia Pty Limited was contracted by Thiess John Holland, to perform the work in this area, including design, modelling, drilling and loading of the explosives, as well as blast clearance and shotfiring. Access to the area was limited so all explosives and equipment, including the 20 t drill rig, had to be lifted in and out by crane. Due to the nature of the blast, with infrastructure 5 m directly in front of the 15 m high face, there was only ever going to be one chance to get this blast right. This was an extremely complex blast which required the use of a number of different types of packaged explosives, as well as special timing techniques only made possible by using electronic initiating systems. This type of blast is high risk, and is more typical of a building demolition in the urban environment. The blast was fired on the 25 September 2010, and was highly successful. The environmental results for vibration and overpressure were well under the imposed limits, and the embedded concrete piles remained undamaged.

Nov 8, 2011

By L Salvestro

Ventilation on demand (VOD) has been demonstrated to significantly reduce operating costs for ventilation fans, by reducing fan output to meet demand. The most effective method for reducing operating costs is to use variable speed drives to adjust the speed of ventilation fans as required – this achieves significantly larger power savings that damper or vane control alone.However, this mode of control will significantly increase the number of speed cycles the ventilation fans will experience. Fabricated impellers have a limited number of start stop cycles based on the materials and method of construction, and the operating stresses due to centrifugal forces. This means that fans experiencing constant or regular speed changes will experience a reduced fatiguelife compared with fans that are run at constant speed.The fatigue life of fans operated under various speeds using VOD is difficult to predict, as it is dependent on the magnitude of speed changes, and the frequency, which will be varied to meet demand. It is important to be able to estimate remaining fatigue life to assist in maintenance planning and avoid unplanned maintenance activities.This paper will review extensive VOD data on fan operating conditions from two primary mine ventilation fans. This paper will demonstrate how this data can be used to calculate accumulated fatigue and predict the remaining fatigue life, and how this compares with fixed speed or non-VOD controlled fans.The increased maintenance costs for the impellers will also be estimated, and compared to the operating cost savings using VOD, to determine if the savings outweigh the additional maintenance costs.

Oct 12, 2022

By T Zhao, K Wang, Z Zhang

Tailings pond safety monitoring is vital for preventing dam failures and ensuring environmental safety. Unmanned Aerial Vehicles (UAVs) can enhance tailings pond monitoring with flexible operational cycles and the ability to collect remote sensing data from inaccessible areas. While many mining operations have adopted UAVs for tailings pond management, their full potential in data acquisition and subsequent analytical processing remains largely untapped. This paper explores various case studies where UAVs have been utilised for monitoring key aspects of tailings ponds such as beach line indicators, dam displacement and erosion, slurry discharge processes, and tailings pond capacity. We also present examples where data derived from UAVs have been instrumental in slope stability analysis, seepage modelling, Tailings Dam Breach Analysis (TDBA), and risk prediction. By integrating UAV technology with traditional ground-based sensor techniques, this approach significantly enhances the precision and reliability of hazard prevention and management in tailings pond operations.

Sep 1, 2024

By A Jakowetz

OxianaÆs Sepon Copper Operation (part of the combined Sepon Gold and Copper Operation) is located in Savannaket Province, in southern central Lao PDR. The site is relatively remote, being some five hours inland from the Laos/Thailand border crossing on the Mekong River. The copper processing plant was designed to treat 1.3 Mtpa ROM ore to produce 60 000 tpa of copper cathode. Commissioning of the processing plant was completed in mid March 2005 with ramp up completed in January 2006 with 5260 tonnes of cathode harvested in this month. The focus of this paper is on SeponÆs unique grinding circuit. The entire grinding circuit is operated at highly acidic conditions, adding a number of different operational issues over and above those normally associated with grinding circuits. It became evident early in the ramp up, that reaching design mill throughput of 170 dry tonnes per hour with the original design would be challenging, coupled with the realisation that ceramic grinding media consumption had been underestimated. In order to lift the overall throughput of the processing plant, a significant continuous improvement process has been implemented within the grinding circuit to lift this key unitÆs production capacity. This presentation will focus on the key areas that have been addressed in the 12 month ramp up period and highlight areas for future work. Results to date have shown this improvement process to be very successful, with throughput rates in excess of 200 tph regularly achieved.

Jan 1, 2006