Search Documents

By M Johnson, M Horrigan

The scope of this report is to examine the aforementioned hypothesis by performing a detailed analytical comparison of a P&H electric rope shovel to an O&K diesel powered hydraulic excavator. In order to complement the integrity of the concluding results, two different size categories will be analysed in order to demonstrate that the findings can be extrapolated and applied to all the machinesÆ size classes. These two size classes are categorised by their bucket sizes and they are in the range of 43 - 58 cubic metres and 23 - 26 cubic metres. It should be noted that electric powered hydraulic excavators will not be considered in this report. In order to compare the electric and hydraulic types, the machine variants that will be analysed are commercial cost-effectiveness and operational flexibility. Although operational flexibility can be an ambiguous characteristic, a clear and thorough definition describing its exact meaning has been included. In order to simplify this study, all the data collected for this comparison have been for overburden removal, eliminating the variation that occurs with the movements of the shovel when selectively mining in the ore deposit. Thus, it ensures that all the data that is compared stems from a common origin for all the shovels. In other words the information will be compared when digging in the same material, loading into the same sized haul trucks, and when possible, with the same operators. Theoretical data received form the respective manufacturers, and actual data obtained from Mount Whaleback, was used for this comparison. This leads to the final comparison, where the operational flexibility and the cost-effectiveness are evaluated, with respect to their individual importance, ultimately influencing the final recommendation.

Jan 1, 2002

In the minerals industry allocating capital for setting up a new project or for upgrading an existing facility usually requires that a compromise be found between the initial cost of equipment, its operating performance and on-going operating costs. To maximise the return on the investment usually requires that various possible combinations and layouts of equipment be assessed. This task is both difficult and time consuming. Computer simulation can be used as a means of determining the expected operating performance of a range of alternate equipment configurations. Simulation is a particularly important technique for analysis as it is one of the few approaches that allows the analyst to take into account the variability inherent in a mining process. While computer simulation is a well established technique its use, until recent years, has been limited to large organisations with access to substantial computing facilities. However, with the current availability of low cost computing platforms combined with easily understood animated displays, simulation is now becoming more widely used across the industry.

Jan 1, 1990

By M Stewart

The structural framework for the major gold deposits of the Reefton Goldfield was largely established in the 1930s after a detailed regional geological mapping programme. Recent new mapping has now substantially modified the structural framework of the Globe Hill - Devils Creek area and the Waiuta area. Using bedding-cleavage vergence as a method of establishing fold limb facing, many new fold structures have been identified, some of which conflict with long-established structures such as the Globe Hill and Waiuta anticlines. In addition, the mapping of areas of west- versus east-facing limbs constrains the position of many faults. The mineralised Globe-Progress Shear is one such fault which graphically demonstrates major structural discordance of the folds in the hangingwall compared to the footwall. Recognition of the folding is establishing the structural framework for understanding of the origin of these productive gold mining areas.

Jan 1, 1996

By A Kite

Frontline leaders play a critical role in the safe and productive operations of Australia’s mining, resources and heavy industries. These leaders set the workplace culture, especially during night shifts and weekends, by providing team direction and encouragement, providing access to resources, fulfilling statutory requirements, enacting and reinforcing risk management systems, setting the standards on shift and acting as the primary conduit of communications between senior leaders and team members.

May 5, 2022

Fleet management systems have been adopted by many open pit mines throughout the world and the resulting improvement in truck cycle times has been one of the most significant contributors to mine efficiency. Ongoing enhancements to fleet management systems such as interfaces for vital signs monitoring have given incremental efficiency gains. Each incremental improvement is another step towards a grand vision of a totally automated mine. A relatively new fleet management system is being integrated with two other technologies to provide a highly reliable platform for a networked information system which monitors mine machinery and production. The paper reviews the integration project, the features of the new mine site information network platform and the contribution to productivity and safety. The new fleet management system has a predictive truck dispatch algorithm. It also has a distributed database that replicates rapidly so that each machine in the fleet has an identical database, thereby making each machine aware of other machinesÆ locations on the site. High precision systems for navigating and monitoring machinery such as drills, dozers, draglines and shovels provide individual machine operators with cockpit style real-time information to increase their operational efficiency. The integration of the new fleet management systems capabilities with the high precision systems that provide production information, machine vital signs data and operator information means that the mine operations and maintenance managers have real-time access to the whole mine siteÆs production data. Such a mine monitoring and reporting system is dependent on reliable wireless communications and reliable positions. Positions in fleet management and high precision systems for open pit mines are usually provided by global positioning system (GPS). Other global navigation satellite systems (GNSS) such as Glonass, and in the future Galileo, will provide additional satellite cover; however, some parts of open pit mines do not have enough sky visibility for reliable GNSS positioning and so a new centimetre level wireless positioning system called Locata is being integrated with the fleet and high precision systems to augment and backup the GNSS positions. The final integrated system will provide the highest levels of reliable position-based information to all stakeholders in a mineÆs operation, ensuring gains in productivity and safety.

Jan 1, 2008

Preliminary work being undertaken on the optimisation of decision strategies for an open-pit metalliferous deposit is presented. The Optimal Control method has been selected rather than the easier to implement Dynamic Programming method of optimisation since a fundamental criteria of Dynamic Programming is violated. Essentially a system of state equations and decision variables is developed for the operation under consideration.

Jan 1, 1984

By M Bellamy

The DeGrussa copper deposit was discovered by Sandfire Resources in April 2009. Construction of the 1.6 Mt/a concentrator, open pit and underground mining operations commenced in March 2011 with first concentrate production achieved in October 2012. Over the next ten years, DeGrussa grew to include both the DeGrussa and Monty underground mines, establishing itself as one of the world’s premier copper producers with total production of 663 000 t of contained copper by the time the mine closed. Final ore was trucked from Degrussa on 5 October 2022. This paper examines the mine closure experience from both a planning and operational perspective. The paper provides an overview of the site’s mine planning process including the factors involved in determining the end of the mine life and how this was tracked and communicated in the lead up to the end of mining operations. It will also look at some of the specific operational aspects involved in maintaining steady state production all the way through to the last day while facing increasingly challenging conditions. These factors, along with the external factors faced by most of the industry such as labour shortages and COVID related disruptions, contributed to making it an interesting journey to the end of operations at DeGrussa.

Mar 29, 2023

Grey River Gold Mining Ltd commenced dredging alluvial flats in the Grey River Valley in 1989. Previous drilling indicated over 100 million cubic metres of gravels with some 90 per cent of the gold in the bottom seven metres. The dredge built by Rahco, Spokane, was innovative in a number of aspects but particularly in the fact that a separate ladder with a cutter and pump was used to strip the overburden and a bucketline to mine the gold bearing wash below. Metallurgical studies and exploration were initiated when the project commenced. Leasing and environmental considerations were investigated and action taken. While progress is being made, the operation at this stage is not meeting required production and performance. Main problems have been with the stripping system and wear.

Jan 1, 1990

Geometallurgical Study of Copper Oxide Mineralisation Hosted in Gravels of Different Physical Quality

Sep 13, 2010

Extraction of copper from a chalcopyrite concentrate by means of a cupric chloride leach is described. Initially the concentrate is mixed with sulphur in a 9: 1 ratio, and heated to 350-400°C. This converts the chalcopyrite into more readily soluble sulphides, while the iron rejected from the chalcopyrite is transformed to pyrite, which is insoluble in the leach solution employed. A two-stage countercurrent leach using a leach solution of 1 M cupric chloride, 3.5 M sodium chloride, and 1 M hydrochloric acid extracts 98 per cent of the copper, if conducted at 105°C. Iron extraction is relatively low, the mole ratio of iron to copper extracted being 0.17, compared to 1.0 for unreacted chalcopyrite. After dissolution, copper can be recovered by electrolysis, cupric chloride leach solution being regenerated at the anode.Electrolytic power requirement is low, being approximately 0.5 kWh per kg of copper. The sulphur and, most of the iron entering as feed are rejected from the process in the form of pyrite, which remains in the leach residue.

Jan 1, 1974

The Sams Creek gold deposit near Takaka in northwest Nelson was discovered in 1974 by CRA Exploration (CRAE) geologists. CRAE recognised the potential of the area and subsequently undertook a comprehensive exploration programme of geological mapping, soil and rock-chip sampling, geophysical surveys and diamond drilling. Exploration defined sporadic gold mineralisation contained entirely within a deformed and hydrothermally altered, peralkaline granite porphyry dyke with a seven kilometre strike length, and up to 60 m thickness. Rock chip samples indicated extensive and economically significant gold grades over approximately one kilometre strike of the dyke at Main Zone prospect. CRAE completed 30 diamond drill holes at this prospect and defined a limited resource. Oceana Gold Limited recommenced active exploration at the Sams Creek Project in late 2002, focusing on improving the geological understanding and known resource at Main Zone. Completion of 1041 m diamond drilling successfully increased the estimated resource to 10.7 Mt @ 2.12 g/t Au containing 729 000 oz at a 0.7 g/t cut off. A further campaign of 1560 m diamond drilling was undertaken in 2003 - 2004 to extend the resource and test the continuity of high grade mineralised zones. Deeper intersections of the porphyry dyke indicated geometrical complexity and grade variability similar to that observed at shallow levels. Recent research suggests that Sams Creek can be geologically classified as a variant of intrusion-related gold systems, and therefore comparable to some other, very large gold deposits. However, due to the rugged terrain and dyke geometry, surface drilling is reaching the limits of viability at Main Zone. If infill drilling continues to be successful then an underground decline may be developed to facilitate further exploration. Potential also exists along strike, where other significant gold anomalies are known but largely untested by drilling.

Jan 1, 2004

I find that during the short time I have been in this district, the majority of boilers are, and have been, receiving very bad usage owing to the difficulties which they have to contend against, viz., oil and bad water. Oil on the heating surface of a boiler is of a highly dangerous nature inasmuch as it allows the surface to become overheated, owing to the water not coming into direct contact with the plates, and it naturally follows that when the crown sheets of a flue or firebox become overheated, you lose a considerable amount of the strength of the plate, and the flue or crown comes down. Referring to the oil question, I find that too much care cannot or exercised on the part of engine drivers in order to minimise as much as possible the internal lubrication of the various engines under their control. For I consider that it is here that the most of the trouble is caused. My reasons for stating such to be the case, are:-That the majority of enginedrivers before coming to this field have been used to driving engines that have been exhausting into the atmosphere, and probably they have been taught that it is far better to use a little extra lubrication than to have a hot bearing. So far so good. But one thing that must not be overlooked is that on these fields the conditions are altered in this respect, as the majority of engines in this district are not exhausting into the atmosphere, but are condensing their exhaust steam and using the water so condensed for feed purposes.

Jan 1, 1901

By P Goblet, S A. Séguret, E Cordier, A Galli

In salar-type deposits, lithium grades can be measured by bailers introduced at different elevations in the drill holes at locations where, later, the brine will be pumped out to recover the metal. When they are duplicated, these a priori rudimentary measurements may show large differences without indicating whether this is due to the procedure itself or to some physical causes linked to the dynamic behaviour of the salar (seasonality, rainfall, underground flow etc). In the reservoir presented in the paper, the problem is complicated by the double lack of stationarity of the lithium grades: the grades not only increase importantly with the depth but at the same time their fluctuations decrease, making it necessary to use non-stationary geostatistical techniques to simulate them. Reservoir simulation is developed in two steps: first, geostatistical simulations of the lithium grade create possible realisations of the reservoir; then, each geostatistical simulation is followed by a pumping simulation that calculates, at each drill hole of a given extraction scenario, the lithium produced each year over 40 years. For the set of 100 simulations produced in this way, a scenario reduction is made to choose the five most representative simulations where more complex calculations will be carried out (for example, changing hydrogeological parameters such as porosity and permeability, or the elevation of the filters, the number and the location of the pumping and the reinjection drill holes etc). The paper first presents an analysis of the geostatistical model sensitivity to the grade uncertainty when measured by bailer. Among the 100 measurements at our disposal covering the future production domain, 50 per cent are duplicates measured at the same place but at different times. They are randomly sampled to produce five subsets of 75 values, which will constitute the future 3D conditioning points for the geostatistical analysis and the simulations. For each subset, trend, standard deviation and variogram models are fitted, leading to five sets of 20 geostatistical simulations of grades. In this way, the reliability of the different parameters involved in the procedure is evaluated, as well as its impact on the pumping results. Then, a reconciliation study is conducted between the non-stationary nugget effects encountered in the 3D variograms of the lithium grade and a pure statistical analysis of 25 duplicates measured at different locations and/or different times. The result is that if the nugget effect reaches 20 per cent, which is the case of three conditioning subsets out of five, the reconciliation is good and the nugget effect of the variogram model represents the bailer uncertainty, ie the measurement error. Since the geostatistical simulation incorporates a nugget effect, it handles the bailer uncertainty and the impact on the produced metal is included in the evaluation. The final conclusion is that, after the hydrogeological pumping simulations, the initial differences between the five geostatistical models do not influence the final results: lithium grades measured by bailers can lead to a robust evaluation of the extractable resources, a conclusion that conflicts with conventional wisdom.CITATION:Séguret, S A, Goblet, P, Cordier, E and Galli, A, 2017. Bailer uncertainty evaluation in a lithium salar deposit, in Proceedings Eighth World Conference on Sampling and Blending , pp 395–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Bernard G, Limpach R, Ulveling L

A major aspect in competitive ironmaking is to replace metallurgical coke by injecting alternative cheap fuels. Whereas in the past, heavy oil injection as well as on a lower scale natural gas injection have proved to be reliable, the progressing high price level of these fuels has prompted international interest in looking for alternative cheaper fuels, especially pulverized coal. Theoretical analysis and practical operations showed that for constant adiabatic flame temperature, potentially more coke may be replaced by injected coal than by heavy oil, because of less endothermic cracking of hydrogen components. Since about 1974, the ARBED-Group has been looking for alternative fuels and in 1976 came to conclusion to select for first trials pulverized lignite for the following reasons:

Jan 1, 1981

By Miovski P, Hooft P. V

In the majority of recently commissioned gold mines granular activated carbon is used to adsorb gold from alkaline cyanide pulps or solutions. At the same time the carbon also adsorbs many other inorganic and organic species, most of which lower the activity of the carbon. Removal of these foulants is necessary before the carbon is reactivated and recycled. Standard practice for re- storing carbon activity involves high temperature treatment in a kiln - an apparently straightforward unit operation which is not always satisfactorily carried out. This paper presents the results of some fundamental work carried out on the thermal reactivation of carbon in a laboratory rotating pot kiln. The effects of temperature and steam addition on carbon activity were examined and compared with the activity of carbons obtained from a number of commercial kilns. Carbon was also reactivated using a small-scale Rintoul Furnace in which carbon was resistively heated by the direct passage of an alternating electric current. It was established that both elevated temperatures and the addition of steam to hot carbon generally enhanced its activity although peat-based extruded carbons responded a little differently to coconut shell types. Other measurements made included the weight loss and the hardness of carbons as a function of reactivation conditions.

Jan 1, 1987

By Turnbull AG

The direct smelting of zinc sulfide con- centrates has been investigated by an extensive series of computer-based thermodynamic equili- brium calculations. The study covers both pure 7.n-S-O-C-N systems and practical concentrate- coal-air-flux systems. It is shown that for a zinc concentrate containing iron and lead sul- tide impurities, a 97% yield of zinc vapour with autogenous operation can be obtained under carefully optimized conditions. The possible integration of this process with existing zinc condensation and recovery processes is Discussed.

Jan 1, 1980

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By A Keogh, P Allen, P Stoker

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Private equity (PE) firms are comparatively free of mandatory requirements for the level and scope of due diligence applied prior to making investment decisions in minerals projects when compared to listed entities, sovereign funds or financial institutions adopting the Equator Principles (Equator Principles Association, 2013). While this freedom allows for flexibility, agility and innovation in making investment decisions, it can also expose PE firms to material risks that may impact their ability to successfully list the projects or attract later financing.Financial institutions and investors with mandatory due diligence and disclosure standards may refrain from investment in or acquisition of a project if it fails to meet various performance requirements. There are many high-profile projects that have suffered significant write-downs on book value after acquisition because specific non-mining issues were not adequately assessed. Thus, a PE firm may be left with an asset that is difficult to divest and incapable of securing development finance.PE firms can manage this risk by being aware of the growth trend in the adoption of ‘international standards’ in addition to host nation standards and legislative requirements. This paper outlines key issues for PE firms to address to maximise the chances of obtaining funding or successfully taking an exploration or mining project through to listing or divestment. Two steps are required: identification of gaps in performance and priority matters of interest to financial institutions and development of action plans to ensure that the priority requirements are met or capable of being met.A PE firm can set its project for success by understanding the social and environmental performance requirements of international standard financiers and by setting the project on the right path to meeting these requirements, and thus making it an attractive investment.CITATION:Allen, P, Stoker, P and Keogh, A, 2015. Setting for success – private equity exploration and mining project buy-in to listing and divestment , in Proceedings PACRIM 2015 Congress, pp 93–100 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By S Hapugoda, Y Tang, L Lu

The steel industry is one of the global leading CO2 emitters, accounting for approximately 7 per cent of global anthropogenic CO2 emissions. In 2022, the world produced 1878.5 Mt of crude steel. About 70.8 per cent of the world’s crude steel was produced by integrated steel mills through the blast furnace and basic oxygen furnace (BF-BOF) process, while the remainder was produced largely by mini mills using electrical arc furnaces (EAF). Compared with gas-based DRI and scrap-based EAF processes, the direct CO2 emissions from the BF-BOF process and the coal based DRI and EAF process are significantly more, as both the processes rely heavily on fossil fuels, such as coke and pulverised coal, to provide energy and reduce iron oxides. Hydrogen is very reactive and reduces iron oxides to metallic iron without generating CO2. Therefore, substitution of hydrogen for fossil fuels in these processes presents a good opportunity to significantly decarbonise the steel industry. This paper will first discuss the thermodynamic and kinetic characteristics of hydrogen and carbothermic reductions of iron oxides and then examine the behaviours of different ore types present in Australia iron ores during hydrogen reduction.

Sep 18, 2023

Laboratory studies of batch and continuous screening of ferrous sinter mixtures (4-0.5 mm) are described. The results are analysed by an equation derived from the first-order rate law for the condition of decreasing screen residue.The results of the studies show that the two screening operations are comparable in all respects if deck length in continuous screening and time in batch screening are interchanged.It is shown that the general screening process is determined by the numerical values of the screening rate constants of each of the particle sizes in the feed mixture and that the relationship between these constants and the particle size/screen aperture ratios is related to the appropriate probability function of the same ratios.It is also shown that the screening rates decrease exponentially with the amount of near-mesh material present in the feed and that oversize particles can increase these screening rates for some screen motions and decrease them for others.

Jan 1, 1985