Search Documents

By S Jayakumari, E Ringdalen, V Canaguier

Silicomanganese (SiMn), containing approximately 16–30 per cent Si, is produced in submerged arc furnaces using various Mn sources and quartz as the primary raw materials, along with fluxes and reductants. In the high-temperature zone known as the coke bed, a silica-rich slag is formed. SiMn is produced through the reduction of SiO2 from the slag. Dissolution of quartz into slags with different compositions, the primary slag formed from the Mn sources and flux before any MnO reduction occurred, representing conditions at the top of the coke bed, and dissolution of quartz into a partially reduced slag to simulate conditions inside the coke bed has been investigated. Experimental investigations were carried out to study the dissolution of quartz particles of varying sizes, 5 mm and 25 mm in synthetic slags with different compositions at temperatures between 1400°C and 1600°C, with varying holding times. Observed results are compared with liquidus compositions and equilibrium phases for original and formed slags. Particle size has been shown to be of little importance for the dissolution. Quartz dissolved more easily in slag at top of the coke bed than slag in the coke bed. Complete dissolution was observed after 30 mins at 1600°C in all cases, but not after 0 mins.

Jun 19, 2024

In an earlier paper (Stanton, 1953) a brief account was given of the geological environment and structure of the Lloyd Copper Mine orebody, Burraga, N.S.W. The present paper is concerned with the chemical and mineralogical features of the ore from this mine.Investigation has been made difficult because of inaccessibility of the workings, which have been fallen in for many years. The exact positions within the orebody of the specimens described in this paper are known in only a few cases. The specimens examined are from the collections of the Mining and Australian Museums, Sydney, and from material collected by the writer from the upper parts of the mine and from various dumps about the old workings.However, no significant variations in the nature (as distinct from grade) of the ore have been mentioned in the old reports, or by Carne (1908) or Kenny (1928), so it is likely that the specimens examined are reasonably representative of the orebody as a whole.CHEMICAL CONSTITUTIONThe ore is of simple and apparently very uniform composition.It is essentially a copper ore, with minor amounts of zinc and very minor amounts of lead. Plotting of copper against zinc shows a more or less sympathetic relationship between these at least as far as 20 per cent. copper - the highest grade assayed during the present investigation. The trend of the plots indicates a Cu/Zn ratio of about 15/1 to this point. Lead is very low and extremely sporadic, showing no clear relationships with the other metals.MINERAL COMPOSITIONThe principal non-opaque minerals are quartz and sericite, and these are accompanied by smaller quantities of muscovite, calcite and biotite. Quartz is the most abundant mineral, occurring both as a C'onstituent of the country rock a quartz-sericite schist-and as veins. All quartz aggre...

Jan 1, 1955

By B Olsson, R Norman, M Volz

Australia has seen unprecedented demand for coal exports in the last ten years and this demand is set to expand further still according to many analysts. This rapid increase in demand has placed pressure on multi-user coal chains to guarantee the capability to meet the required demand, in terms of both current operations and capacity expansion.The projects required to deliver these forecast tonnages take place in an increasingly complex commercial and technical environment. These challenges include brownfield and greenfield projects, multiple rail and terminal service providers as well as a myriad of mine operators, all needing to operate in an increasingly integrated manner to get the most out of expensive shared assets.Increasing complexity and integration drives the need for more holistic and sophisticated analysis tools. The capacity of coal chain subsystems, such as mine, rail and port, can no longer be determined effectively in isolation. Understanding the nature of the interactions between these subsystems and the resultant capacity of the integrated system is the key to maximising value. TSG advocates the use of a total integrated system approach to understand the behaviour and performance of complex coal chains.Recently, TSG has worked in conjunction with the Integrated Logistics Company and a number of stakeholders in the Dalrymple Bay Coal Chain to deliver the first independent system master plan. This master plan has provided a quantitative and rational assessment of coal chain capacity in its current state and a prediction of its capacity once a pipeline of committed capacity improvements is in place. It is underpinned by a highly detailed discrete-event simulation model of the complete coal chain as an integrated system, including mine load-outs, rail, terminal and port operations.This paper provides an overview of the study and describes the differences between subsystem and total integrated system model performance.

Sep 26, 2011

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By G J. Harbort, Z Pokra

It has been observed in several Jameson cell installations where the source for flotation feed is deslime screens, that the recovery of coal particles greater than 0.5 m is not as great as that of finer material. Consequently, a research project was undertaken at a CHPP in the Bowen Basin, Queensland, to assess the possibility of increasing the recovery of coarser particles (+0.5 mm) within the downcomer of the Jameson Cell. The effect of decreasing turbulence and agitation in a commercial-scale downcomer was investigated to assess the effect on the recovery of both coarse and fine coal particles. This paper details the findings of the testwork, summarising the results relating to differences in the operating parameters within the downcomer.

Jan 1, 2005

By M Amanzadeh, S M. Aminossadati, B M. Masum, M S. Kizil, C R. Leonardi

Gas sensing systems are becoming more important in many industries such as oil, gas and mining operations. Particularly in underground coalmines, accurate and reliable monitoring of toxic and combustible gases such as methane, nitrogen dioxide, carbon monoxide and hydrogen sulfide is essential. Available conventional electrochemical sensors for gas measurements in underground coalmines suffer from shortcomings such as cross-sensitivity response, limited lifetime, high calibration cost, maintenance cost and safety. Recent studies have found that fibre optic-based gas sensors have potential to eliminate these issues. These sensors can also be used for long distance and distributed sensing of various gases, both of which are important for underground gas monitoring. The aim of this paper is to review the present underground mining gas monitoring systems and review the new generation of fibre optic-based sensing systems for use in underground coalmines.CITATION:Masum, B M, Aminossadati, S M, Leonardi, C R, Kizil, M S and Amanzadeh, M, 2017. New generation of gas sensors for underground coal mining applications, in Proceedings Australian Mine Vent Conference 2017, pp 189–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By C Mpodozis

Central Andean (22¦S to 34¦S latitude) Miocene giant ore deposits share common features that reveal their origin. Tectonic and magmatic features include a relation to a shallow subduction zone, an association with the waning or initiation of a magmatic episode, emplacement at the time of uplift associated with crustal thickening and formation at times of major magmatic changes along the Andean margin. Rare Earth Element (REE) signatures in magmas erupted near the time of mineralisation indicate a progressive change from equilibration at depth with a hydrous, intermediate-pressure amphibole-bearing mineral residue to equilibration with an anhydrous high-pressure garnet-bearing assemblage. These features point to a common history. First, a relatively shallow subduction zone leads to hydration of a cool mantle wedge providing a source of fluids which builds up over at least several million years. Arc magmas formed at this time equilibrate with a hornblende-bearing residual mineralogy. Second, a compressive tectonic regime leads to crustal shortening and thickening that facilitates entrapment of arc magmas in the crust. Eventually, the magma-weakened crust yields to horizontal compression causing rapid crustal thickening. Fluids required for mineralisation are liberated as amphibole-bearing assemblages break down to garnet-bearing ones and over pressured fluids are released from plutons. Mineralisation subsequently ceases in the region unless continued dehydration of the slab and mechanical thinning of the continental lithosphere causes the previous conditions to repeat. The type of mineral deposit generated depends on the pre-existing continental lithosphere and the distance from the trench.

Jan 1, 1999

In coal mining, geophysical techniques have an established application in determining the location of seam boundaries ahead of the face so that underground mines can be planned to avoid any geological structures that might disrupt production. Geophysics can also be used in geotechnical studies to determine the in situ properties of the rock mass and the response of the rock mass to the mining. The use of geophysical logs and microseismic monitoring in these geotechnical applications are discussed in this paper.

Jan 1, 2002

By A J. Falconer

Two magnetic parameters are proposed as a basis for the assessment of ironsands beneficiation. The parameters are determined for raw sand prior to dredging and for magnetic separator head feed over a production period of five months. The relationships between these parameters and the performance of the magnetic separators are examined to establish the value of magnetic assessment compared with the traditional soluble iron assay method. The results illustrate that the first parameter, true magnetic fraction (TMF). Has a value superior to that of soluble iron when relating raw sand grade calculated by triangulation to magnet performance. In terms of the relationship between magnet head feed grade and magnet performance, TMF and soluble iron perform equally as assessment parameters. For the ironsands mined during the five month period, the second magnetic assessment parameter, composite fraction (CF), is shown to merely reflect TMF and offers no additional information for assessment. Conclusions are that true magnetic fraction has many advantages over soluble iron in terms of time and cost of determination and that it is a meaningful and reliable parameter upon which to base all calculations relating to the mining and beneficiation of ironsands.

Jan 1, 1980

Underground equipment owners and users in order to compete and succeed in being viable business propositions must continually balance costs with productivity. By reducing their hourly ownership, operation and maintenance costs and increasing their hourly production, the cost per unit of material mined will be optimized.

Jan 1, 1990

In a state-of-the-an review of predictive methods for longwall support load calculation, special respect is paid to those techniques which enable actual roof conditions and local lithology of strata to be involved. Principal systems of roof examination include the borehole perforation test and seismic velocity measurements. Roof strata stability is related to caveability classifications and roof inclination due to subsidence. The critical analysis of both load resistance prediction methods and roof stability classifications shows that each has its own value of reliability level. The present research opportunities analysed underline the significance of developing fully reliable prediction techniques as needed by the coal industry.

Jan 1, 1991

By Fookes R. A, Gardner K. J, Gravitis V. L, Watt J. S, Steffner E. J

Two radioisotope techniques suitable for the rapid laboratory determination of the ash content of coal have been tested ou unwashed coal samples from four Australian coal seams. In one techniqne, measurements of backscattered 238Pu L X-rays and iron K X-rays from finely ground coal samples have been combined to determine ash content in uuwashed coals to ±0.5 weight per ce111 ash (ls) for three seams and 0.9 weight per cent ash for the fourth.The second technique, which involves measurements of the transmission by the coal of narrow beams of 241Am 60 keV and 123Ba 356 keV ? rays, requires less sample preparat ion. The ash was determined to within the range of 0.8 to 2.6 weight per cent for the four seams (unwashed coal). For washed coals, errors are expected to be < ±0.5 weight per cent ash.

Jan 1, 1982

IT is not intended that this paper should be regarded as an account of the geology of the Lyell district. It is merely a synopsis of some of the conclusions recently arrived at in regard to the stratigraphic and structural geology, compiled to act as a guide to those members of the Australasian Institute of Mining and Metallurgy attending the Queenstown meeting who are interested in economic geology. The attempt has been made to present certain salient features, omitting a mass of detail, which, although important in the complete investigation and understanding of the economic geology, yet would be confusing to a group of geologists making a short visit. The location of some of the significant occurrences bearing on the main problems and conclusions are indicated in the text in order to enable members to plan the location and direction of their excursions...

Jan 1, 1927

By Andrew A. A, Hamilton P. J

Constraints on pore water evolution in the aquifers of a sedimentary basin may be realised through stable isotope analyses of present day waters, and their comparison with water compositions calculated to have been in isotope equilibrium with the products of diagenesis during burial. Integrated with detailed petrographic observations, and thermal, structural and stratigraphic analyses, fluid migration patterns at various stages in a basin's history can be identified. This has important implications for modelling basin hydrology, hydrocarbon distribution, and reservoir quality in the Latrobe Group, Gippsland Basin, and oil-prone successions Elsewhere.

Jan 1, 1992

By Heesteman LJL, Turvey DJ

The Mangani mine in West Sumatra is historically one of the most important precious metal mines in Indonesia, although the past production by World standards is small, totall- ing 5.66 tonnes gold and 242 tonnes silver. The geology is dominated by a distinctive NW-SE graben structure formed by dextral splay faults from the Sumatran Fault System. Quartz- rhodochrosite-rhodonite-Ag-Au veins are hosted by Tertiary pyroxene andesite volcanics and quartz-phyllite conglomerates, on N-S tensional fractures which intersect the Mangani graben. Intrusive rocks include andesitic dykes, pyroxene microdiorite, and hornblende granodiorite. Quartz-epidote-pyrrhotite alteration is related to concealed intrusions. Precious metal vein mineralization is characterized by: high Ag/Au ratio (>25); complex sulphide mineralogy of Fe, Mn, Ag, Cu, Pb, Zn, As, Se and the occurrence of Sn as stannite; low total sulphide content (

Jan 1, 1987

By Rogers R, Kinnane T

In a typical open cast mining operation, investigation of how existing truck performance compares with the highest achievable truck performance is largely neglected. This paper addresses this issue by proposing a computerised system that will provide a systematic method for comparing existing truck operational performance to the highest performance considered achievable. Through analyses of existing versus achievable performances, various inefficiencies associated with truck operations can be identified. These inefficiencies could occur due to machine configurations, haul route design and conditions or operator skill level. Remedial action should then be taken in a timely fashion to better manage these factors and to ensure the fleet is always operating at its peak efficiency.

Jan 1, 1994

By J Field

Many aspects of water use in mining are driven by the technical requirements for water. There has been little consideration given to both the safety and the health requirements. Workers in the mining industry are exposed to water from a range of treated and untreated sources. The intended use of this water dictates the required quality of the water, sometimes with limited consideration for contact with miners. Particularly for underground workers, there is exposure while working in and walking through groundwater possibly contaminated by hazardous substances. Where controls are inadequate the outcomes of this exposure can result in disease, illness and injury û the costs of which can be significant. The situation could also arise where, due to the lack of human exposure, the controls are unwarranted and the financial cost unjustified from a health perspective but warranted from an equipment management standpoint. In addition to the health aspects, water can impact on a range of safety issues resulting from high pressure usage, dust suppression, fire fighting and other processes. The protocols and procedures in place need to consider the safety issues in addition to managing water usage. The current state of water management in mines from an occupational health and safety perspective has been ascertained from a survey targeting underground and surface coal and metalliferous mines. This survey considered the health and safety issues associated with water use, the types of surveillance, control protocols and the strategies that the mines have in place to manage the health and safety risks associated with water systems. The results assisted in the identification of potential occupational health and safety risks associated with water systems and the management processes that may be appropriate from a risk management perspective. Health and safety issues are often neglected but remain critical issues affecting the value of water to the mining industry.

Jan 1, 2006

Exploring the Breakage Environment in Mills with Discrete Element Methods

Sep 13, 2010

By M Kim, J Park, I-K Suh, E Kim, J Lee

One of the key technologies in developing hydrogen-enriched ironmaking operations is the control of the carburisation, melting, and dripping behaviour of the iron ore burden materials. When a hot compacted iron (HCI) is charged in the blast furnace or the FINEX Melter-Gasifier, iron oxide reduction, the reduced iron’s carburisation, and the melting of iron and slag occur successively. This study investigated the reduction, carburisation, melting and dripping behaviour of HCI under a COH2 gas mixture using the high-temperature X-ray radiographic technique. Under 100 per cent CO gas atmosphere, the dripping temperature was 1410°C. When 5 per cent H2 was introduced, the dripping temperature slightly decreased to 1400°C. Furthermore, the dripping temperature gradually increased as the H2 gas composition increased. As 30 per cent H2 was introduced, the dripping temperature reached 1414°C. The carbon concentration in the drained metal samples gradually increased with increasing H2 composition. It is considered that H2 decreased FeO content in the slag, yielding the increased melting temperature and viscosity of the slag. On the other hand, H2 accelerated the carburisation of the reduced iron by CO gas, enabling the homogenisation of the oxide materials to form a liquid phase. Therefore, it is considered that introducing H2 in the reactor is helpful to increase productivity and energy efficiency by accelerating the liquid phase’s formation.

Aug 21, 2024