Search Documents

By W Blair, J Bosman

The measurement of ferrosilicon rheology and characterisation of the parameters that have a direct influence on medium rheology provide the basis for evaluating, comparing and selecting an appropriate size and shape of medium to maximise separation efficiency in a dense medium application. The role of medium viscosity on particle separation in both static and dynamic separators is illustrated using relevant theory. The primary measurements of rheology are medium viscosity and stability. These in turn are determined by particle size, particle density and particle shape which in turn can be quantified. Additional characterisation parameters are also discussed. Different areas of application where ferrosilicon characterisation can be used are also discussed.CITATION:Bosman, J and Blair, W, 2017. The practical characterisation of ferrosilicon for dense medium applications, in Proceedings Iron Ore 2017, pp 135–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

THIS paper is the outcome of experiments carried on and experience gained. at the Waihi-Paeroa Gold Extraction Company's tailings plant at Waihi, New Zealand. The plant was erected to treat accumulated tailings which had been discharged into the Chinemuri River by the Waihi batteries.The Chinemuri River is a common sludge channel for all mining debris, tailings, and ashes from the power plants, the last being the cause of occasional high residues, which gave so much trouble to the management. The tailings were dredged from the bed of the river into barges by means of a Pohle air lift, the power being supplied: by a 13 b.h.p. Tangye oil engine driving an air compressor and a centrifugal pump. The sands were elevated from the barges by bucket-belt elevators over screens, to eliminate large particles and rubbish, into storage hoppers, and from there fed direct into four C. Judd Ltd. tube mills.The method of treatment was fine grinding in a weak cyanide solution, agitation in B. and M. tanks, filtration with turn-over vacuum filters, and precipitation with zinc shavings. The comparatively high values of the residues in gold gave a great deal of trouble, 'and it was not until repeated experiments were carried out that the cause of the trouble was located. While the value of silver residues remained stationary, the gold values...

Jan 1, 1912

Study on Dynamic Characteristics of Inertia Cone Crusher and Its Application

Sep 13, 2010

By R Robinson

Modem occupational health practice can be described as the fitting of work to the individual and each individual to his job; perhaps a non-traditional way to view occupational health. This two-component description is achieved through the development of programs to implement and monitor specific job procedures, from the monitoring of unwanted exposures to contaminants to the auditing of mine sites. This paper is about such programs. Some attempt must be made to evaluate the effectiveness of the program and several performance indicators which are intended to measure the effectiveness of such a program are offered.

Jan 1, 1994

Effects of High Pressure Grinding Rolls on Platinum-Bearing Ores and the Flotation Response as Compared to the Conventional Ball Mill Three major PGM ore types from the Bushveld Complex of South Africa: Merensky, UG2 and Platreef were comminuted with the use of the high pressure grinding rolls (HPGR). The influence of the feed characteristics and the various operational and design features of the HPGR on energy consumption, throughput, mineral liberation and PGM flotation recovery were investigated. The test work variables included two feed top sizes of 12 mm and 6 mm, specific grinding forces ranging between 3 - 7.5N/ mm2 and zero gaps of 1.5 mm and 3 mm. The results show that the influence of the HPGR operational and design features on energy consumption, throughput, mineral liberation and PGM recovery are ore dependent. The size reduction-specific energy relationships show that the most energy efficient utilisation of the HPGR for Platreef ore was at the lower specific grinding force of 3N/mm2 and the zero gap at 3 mm. For Merensky and UG2 ore on the other hand, the most energy efficient operation was at the higher specific grinding force of 7.5N/mm2 and the zero gap of 1.5 mm. At a specific energy input of 3 kWh/t, reduction ratios (F50/P50) of 6.5, 3.8 and 10 were obtained for Merensky, UG2 and Platreef, respectively for feed top sizes of 12mm. Further application of the HPGR as a pregrinding stage to a ball mill showed a 25 - 30 per cent increase in throughput for Merensky and UG2 ore. Batch flotation tests performed on selected samples appear to indicate that ore comminuted with the ball mill had superior grades compared with that ground with the HPGR. However, Merensky and UG2 ore comminuted at different HPGR operating conditions showed distinctions in PGM recovery. Platreef on the other hand did not appear to show any differences. Therefore, this study highlights the significance of ore type and operating variables in HPGR applications with regards to energy efficiency, throughput and PGM recovery.

Sep 13, 2010

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

Though many mining and mineral processing companies have embraced the principles of sustainable development (SD), there is still a significant challenge of applying these in a practical sense, either in plant design or as part of day-to-day operations. The high-level nature of sustainability concepts often do not translate easily into workable activities or business case evaluations. This makes it difficult for engineers and company decision makers to understand whether their actions are making a contribution to sustainable development and a long-term business case. While several organisations have their own SD tools that can, to a degree, help identify these opportunities, they are largely ad-hoc and lack the necessary thoroughness to defensibly value these opportunities. Recognising these serious shortcomings, the Cooperative Research Centre for Sustainable Resource Processing (CSRP) has undertaken the development and trial applications of SUSOP« (SUStainable OPerations), a new concept that is somewhat analogous to HAZOP and the wider risk and safety frameworks used in projects today. The key goal of the SUSOP« research project is to produce a holistic, systematic and rigorous framework for project development, capturing, recording and evaluating SD opportunities and constraints against a chosen sustainability structure (eg Five Capitals). SUSOP« is being developed through an iterative process with input from research institutions and engineering companies. This integrated approach ensures that SUSOP«, in its final form, will have the academic rigour and industry realism required to assist the resource sector contribute to societal sustainability by embedding the concepts and processes into the design and operation of their assets in a meaningful and practical manner. SUSOP« has created much traction with both engineering companies and mining and minerals operators. This conference paper presents an overview of the SUSOP« framework and its current suite of processes as well as highlighting, through practical case studies, its capability to incorporate SD considerations at different phases of an engineering project's development.

Jun 1, 2010

Amongst representative men directing alluvial mining of erations in Victoria, some difference of opinion exists as to the best system of working the deep leads. The developmental operations of shaft-sinding, extending a reef drive, partially watering and rising up into the wash dirt are practically the same on all fields but subsequent mining is continued either on the Chiltern and Rulberglen or Ballarat systems, the latter being referred to by the Chiltern and Rutherglen miners as the "down country" system. In the former, the leading wash and cross drives are lept from 300 to 500 feet ahead of the reef drive, and in the latter the reverse method keeping the reef drive well ahead of all wash workingsis adopted.In the majority of alluvial mines in the southern and western fields, the initial work of defining the course of the lead is costly, owing to the thick superincumbent layers of hard basalt, to bore which costs from 9/- to 15/· per foot. Unfortunately large sums of money have been wasted in this work, owing to a want of care and knowledge in the selection of bore sites, and improper recording of the strata pierced, thus handicapping alluvial mining and bringing boring operations...

Jan 1, 1902

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

This paper reviews the current techniques employed in the prediction of subsidence and how they have been applied to partial extraction systems. The method using influence functions to describe the shape of the profile is investigated in detail and has been adopted to model the subsidence over workings in Huntly. It is compared with the profile methods developed in the United Kingdom and found to predict the subsidence profile more accurately than these methods.

Jan 1, 1991

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

Study of Bauxite Separation by Using Flotation Column

Sep 13, 2010

The Committee for Mineral Reserves International Reporting Standards (CRIRSCO) was formed in 1994 to promote development and adoption of international standards for estimation and reporting of exploration results, mineral resources and mineral reserves. The CRIRSCO standards have been accepted by most mining companies and professional societies worldwide. Market regulators from Australia, South Africa and Canada require that these standards be followed when releasing public information. Among these requirements is the use of specific definitions for what constitutes exploration results, mineral resources and mineral reserves. If such information is publicly disclosed in must be estimated by a Competent or Qualified Person. In the United States of America, public disclosures are regulated by the US Securities and Exchange Commission. The SEC does not recognise the CRIRSCO guidelines, and some of the SEC requirements for public release of information are materially different from those applicable in other countries. The CRIRSCO definitions and the Competent Person requirements are reviewed and compared with those of the SEC. The organisation of the SEC and its rule making process are briefly discussed. Ongoing efforts to bring the US regulatory requirements closer to those applicable in other countries are presented, as well as other activities that CRIRSCO is entertaining with the United Nations, the International Accounting Standard Board and other international organisations to reach the objective of worldwide standardisation of reporting procedures.

Jan 1, 2006

By A H. Gray

Gekko Systems Pty Ltd engaged in the test work, design, manufacturing and commissioning of the pre-concentration plant at Silver Standard Resources Inc’s Pirquitas mine in the north western Jujuy province of Argentina. Testing of the ore at coarse feeds of between 2 and 12mm returned probable recoveries of up to a total of 95% silver into 50% of the mass fed to the InLine Pressure Jigs (IPJ’s). The plant has been designed and built based on the test results to include a preparation screen to bypass the fines that are naturally higher in grade and repulping of the coarse which is then pumped to three parallel trains of 2-stage IPJ roughing-scavenging. The target 50% yield to concentrate passes over a dewatering screen and the solids are returned back to the mill feed conveyor. The IPJ tails are transferred to a dewatering screen and solid rejects are stockpiled off the end of a transfer conveyor. All dewatered underflow products are processed via hydrocyclones to recover dirty water for use back into the IPJ circuit and return entrained fines to the fines bypass line.With the sulphide orebody being processed, the results from operations to date have shown that plant performance is matching the original laboratory sulphide ore testwork data. The objective of the pre-concentration step is to both reject gangue and achieve grades between 300-400g/t Ag to the float circuit as flotation recoveries are maximised within this range. The plant currently achieves overall upgrades of approximately 150% of feed grade with the IPJ only circuit producing an average 180% increase from calculated feed grade.

Aug 8, 2011

By R Jia, J T. Waldram

"The Caijiaying lead zinc mine is located in China, north-west of Beijing, in Hebei Province. The region experiences severe winters, below -35°C, and warm summers, up to 30°C. The mine and concentrator commenced operations in the second half of 2005 with a conventional tailings disposal system consisting of a tailings dam with peripheral ring main discharge and central water recovery. A second similar dam sharing one common wall was added later. In view of the extreme winter conditions tailings lines and ring mains plus spigots, together with return water lines, require insulation and electrical trace heating. The volume of process water trapped as ice in the tailings dam ponds each winter is significant. This seasonal variation presents a major difficulty in the management of process water availability. Although Caijiaying is an underground mine there was no backfill plant at the start of operations. As plant throughput increased more quickly than originally anticipated, tailings storage capacity became a prime concern. The construction of a backfill plant in 2007 reduced the pressure on surface tailings storage area requirements, but as suitable land on which to construct further tailings storage was both expensive and difficult to acquire, a more efficient use of the available area was required. Dry tailings storage, where flotation tailings are filtered to provide an immediate return of process water plus ‘dry’ tailings filter cake for stacking, provided an answer to both the land area required, and the water management difficulties. The paper details the reasoning behind the change and the benefits obtained at Caijiaying by moving from ‘wet’ tailings storage to ‘dry’ tailings storage.Citation:Waldram, J T and Jia, R, 2016. Caijiaying Dry Tailings Storage, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 379–382 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Applicaton of Agricultural Residues from Pyrolysis in Flotation of Black Coal

Sep 13, 2010

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

By Firkin GR, Allen RJ

Sulphide Corporation Pty. Limited has roasted a number of different zinc sulphide concentrates on its sinter machine which pro- duces zinc-lead sinter for an Imperial Smelting Furnace, and results have varied widely. The differences are considered to be functions of !concentrate particle size and reactivity. Amdel have used differential thermal analysis to examine these concentrates and two major effects have been found. Firstly, in concentrates 1containing small quantities of pyrite and chal- L [copyrite, heat is liberated at 400¦C to 650¦C [by oxidation of these two sulphides. Secondly, as particle size decreases, heat release from the oxidation of zinc sulphide commences at flower temperatures and rate of heat release In a sinter bed, the presence of some rite and chalcopyrite would help to heat the cc sulphide to ignition temperature in a orter time, while a finer concentrate would sult in roasting being completed more ickly. Both of these effects result in a arper flame front and minimise the chance heat and combustion fronts being mismatched. is theory is supported by sintering results tained by Sulphide Corporation. As a result

Jan 1, 1975