Search Documents

In 1961, West Australian Petroleum's Eneabba No. 1 bore encountered 22 seams of coal totalling 40 ft in thickness between the depths of 6373 ft and 6441 ft. On analysis, this coal had a similar calorific value (8000-HOOO B.T.U./lb, assuming 20 per cent water) to the coal from the Collie Coalfield, Western Australia's only known area of commercially exploitable coal. Being buried to depths in excess of 6000 ft, the coal at Eneabba had developed weakly-coking properties, and thus, although much younger than the Permian coals of Collie, gave promise of being a major potential source of power for Western Australia.West Australian Petroleum undertook a programme of stratigraphic drilling and shallow test drilling to determine whether this coalhorizon persisted into the outcrop of the Lower Jurassic sediments in the Hill River district, 140 miles NNW. of Perth, and, if it was present, if the quality and quantity of the coal would warrant development of the deposits by open cutting. The coal horizon was identified in the near surface, but the poor quality of the coal and the complexity of the structure made development (in the area examined) uneconomic at the time.A strong seismic reflection in the Eneabba area occurs at the same depth as the Jurassic coals. This event originates within the upper beds of the Lower Jurassic and it is probable that the velocity contrast between the higher velocity siltstones and the very low velocity coals enhances this very strong, distinctive seismic reflection.This event can be followed on continuous seismic data over a large area of the northern Perth Basin, from 13 miles SE. of Dongara to 20 miles SW. of Coorow. It can be followed from a depth of 4000 ftnear Dongara to over 17,000 ft to the SE., so development of thisvast potential source of power will depend on the economics ofprocesses being developed for the production of power from theburning of coal seams in situ.INTRODUCTIONThe discovery of 22 seams of economically useable coaltotalling 40 ft in thickness in the Lower J urassic sedimentsof the Eneabba No. 1 bore (Fig. 1) led to the search forthese seams at economically workable depths. The Ministerfor Mines in Western Australia granted to West Australian1. Supervising Geologist, West Australian Petroleum Pty. Ltd.Manuscript received at The Institute, 25th May, 1964. and presented to the 1964Annual Conference.

Jan 1, 1964

Developments in the technology of explosive production and deliveryallow a greater amount of flexibility in rock fragmentation by blasting. The rock fragmentation efficiency of an explosive is currently given by a rating which is determined by the explosive manufacturers using proprietary formulae and methodology. Hence, comparison of explosives from different manufacturers may be misleading. Modeling of explosive energy, using a thermochemical code such as CHEETAH provides an objective standard by which the likely performance of different explosive formulations can be determined. Such modeling can be used for optimisation of explosive composition to match specific rockfragmentation objectives.

Jan 1, 2001

By C M. Hall

We report 40Ar/39Ar ages for adularia and illite from veins and wall rocks at the Waihi and Favona deposits, in the Waihi district. One sample of vein adularia from the Favona deposit yielded a plateau age of 6.04 ¦ 0.06 (la) Ma, and two samples of vein adularia from the Waihi deposit yielded plateau ages of 6.17 ¦ 0.03 and 6.17 ¦ 0.09 Ma. Two samples of wall rock adularia from the Waihi deposit yielded plateau ages of 6.07 ¦ 0.06 and 6.08 ¦ 0.03 Ma. Adularia ages overlap at the 2s level, and we do not consider them to be significantly different. Two samples of illite from wall rocks at Favona have total gas ages of 5.66 ¦ 0.04 and 5.65 ¦ 0.04 Ma, and retention ages of 6.57 ¦ 0.04 and 6.61 ¦ 0.04 Ma, whereas one sample of vein illite yielded a total gas age of 5.29 ¦ 0.17 Ma, and a retention age of 6.26 ¦ 0.19 Ma. The total gas ages of illite are minimum ages that are equivalent to conventional K/Ar analyses, whereas retention ages of illite are maximum ages. Although interpretation of the illite data is complicated, the adularia results strongly suggest that the Waihi and Favona deposits formed contemporaneously in the same fossil geothermal system at 6.0 to 6.1 Ma.

Jan 1, 2003

For many years the scrubbing of roaster gas carrying sulphur dioxide has been carried out at the plant of the Electrolytic Zinc Co. of Australasia Ltd. at Risdon, Tasmania, using long horizontal tubes. in which the gas stream crossed a shower of water. In order to provide for increased roaster capacity, it was evident that additional gas scrubbing capacity would be required to prevent pollution of the atmosphere.This provided an opportunity to review the whole operation of gas scrubbing and an investigation was initiated to determine the characteristics of a counter-current type of scrubber. It was hoped that a change to this type of scrubbing would also reduce the sulphur dioxide concentration of the gas delivered to the atmosphere to a negligible amount. This, paper outlines results obtained from an experimental tower which was operated under a wide range of conditions, the packing height, gas flow, water flow, water temperature, and concentration of S02 in inlet gas being varied independently. A description is given of the leading features and operating characteristics of the plant units, which are designed on the basis of the experimental results. Operation of the new scrubbing system commenced on October 5th, 1948.THE PROBLEMThe gas which is handled carries S02 which may vary in concentration from 2% to 5%, and reaches the scrubbing system at a temperature of approximately 180 deg. C. An appreciable amount of suspended material accompanies the gas which has passed the cyclone system.

Jan 1, 1949

By M Carr, C Wheeler, M Lurie, B Chen

The demand for steel products in modern society is prompting the iron ore industry to optimise their operations to ensure sustainability of fines and lump products. One of the key components in the iron ore transportation chain are belt conveyors. The energy consumption of modern belt conveyor systems has reduced considerably over the past few decades, however, there is still significant scope for further reductions, especially when heavily loaded long overland belt conveyors are considered. A new rail based continuous bulk material transportation system has been developed by researchers at the University of Newcastle to reduce the energy consumption of heavily loaded and long overland conveyors. The Rail-Running Belt Conveyor technology is a state-of-the-art continuous belt conveying technology which provides an innovative and novel departure from conventional continuous bulk material transportation systems with significant energy and economic benefits. This paper presents an overview of a Rail-Running Belt Conveyor variant which considers an enclosed belt. Enclosed belt conveying has the benefits of encapsulating the bulk material, and thereby reducing dust emissions and moisture ingress, in addition to being able to negotiate smaller radius horizontal and vertical curves leading to greater flexibility. To quantify the primary differences between conventional conveying technologies, the Denver office of thyssenkrupp Industrial Solutions (USA) developed a case study for an 11 km long conveyor. The conveyor design throughput was 2750 t/h and included a small net elevation loss of 10 m. When considering CAPEX the Rail-Running Pipe Conveyor equipment supply cost is approximately 45 per cent of the cost of a conventional pipe conveyor, while savings upwards of US$50M emerge for CAPEX combined with five years of OPEX. The savings vary with the topography and density of the bulk commodity, with iron ore generally showing increased savings because the high bulk density increases rubber losses in conventional conveyors.

Nov 8, 2021

Jan 1, 2004

The metallogenic map of New Zealand shows the distribution of metallic mineral deposits, according to type and size, in relation to their geological setting. The major purpose of the map and accompanying 200-page monograph is to summarise the distribution, modes of occurrence and origins of the metallic mineral deposits of New Zealand. The map demonstrates the prospectivity of New Zealand for metallic minerals, particularly gold, silver, iron, and titanium. Information on each deposit is summarised in index tables based on major geotectonic units or deposit/commodity type. The mineral deposits are arranged and discussed in relation to tectonostratigraphic and tectonomagmatic units or terranes, under broad geotectonic divisions of the Paleozoic to Mesozoic Western Province, the late Paleozoic to Mesozoic Eastern Province, the mid Cretaceous to early Tertiary rifting phase, and the late Cenozoic Kaikoura Orogen. Regions or areas of marked concentration of mineralisation are recognised as metallogenic subprovinces or districts, namely: eastern Northland (Hg), the Hauraki Goldfield (epithermal Au-Ag-Pb-Zn-Cu), the west coast of the North Island (shoreline placer Fe), east Nelson (podiform Cr), west Nelson (porphyry Mo), the West Coast of the South Island (shoreline placer Ti), west Nelson-Westland (placer Au), Reefton (mesothermal Au-quartz veins), and Otago (placer Au and mesothermal Au-W quartz veins).

Jan 1, 1993

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The cost of power is an important matter to mining companies generally and this thought that the members of the Australasian Institute of Engineers, as well as the engineering and mining professions generally would be interested in any proposal for the reduction of that cost has led to the presentation of this paper.The writer trusts that the description will be found clear and increase the interest in this interesting subject. In the up of the electrical arrangements touched on in this paper, the author has had the able assistance of his friend Mr. Mars, to whom he offers his hearty thanks. The selection of the best class of power plant for a mine is a very difficult and large problem and it is quite out of place to dogmatise that anyone of the many systems that offer is better than another, eg that the all electrical is better than the partly direct steam-driven and partly electrical, or that a gas plant is better than a steam plant. Such a selection is one that calls for very careful and close consideration, in each particular case, of a large number of before it is possible to arrive at a proper decision.

Jan 1, 1912

By D R. Anstey

The mining of magnetite iron ore in Western Australia will generate large volumes of waste rock and tailings over many decades. The need to dispose of these materials will result in massive waste landforms that will require significant planning and management. The formation of comparable man-made landforms is relatively common, as exemplified through past practice in gold and iron ore (haematite) mining. Unfortunately, the performance of these landforms, with respect to long-term stability (erosion resistance), the release of low pH seepage water and aesthetic impact, has commonly been disappointing and environmental legacies have been created as a result. Lessons that have been learnt from past, large mining operations indicate that there is a need to rethink the methods of waste disposal and landform development applied to magnetite mining. The environmental compliance criteria applied to magnetite mines for the storage of tailings and waste typically include minimising dust generation (particularly as the tailings and mine waste may contain asbestiform minerals), control of silt, minimising visual intrusion and management of potentially acid forming materials. In addition, the climate of Western Australia and the paucity of both surface and groundwater in the vicinity of the magnetite mines frequently necessitate water consumption to be minimised. This paper discusses the potential to co-mingle magnetite mining waste streams in a variety of ways to concomitantly satisfy the environmental compliance criteria and the operational requirements of the mine. These methods include co-mingling of coarse tailings and waste through dry-stacking, deposition of tailings as a paste, co-disposing of all wastes to form an integrated landform and the co-mingling of all waste streams to produce PasteRockTM (a blend of tailings paste and crushed waste rock). The paper demonstrates how these techniques can be applied to the magnetite mining industry to provide better outcomes than might be achieved using more conventional techniques, currently employed in large-scale mining operations.

Jan 1, 2009

Longwall mining operations have been in place in Australia since the early 1960s. This mining method is currently used to extract the bulk of coal obtained from underground mines in Australia (CSIRO, 2010). Despite the high tonnages extracted the expected utilisation of much equipment remains relatively low. To some extent this level of utilisation is influenced by the variability in conditions inherent in the mining process. This variability in production rates presents challenges to those attempting to design a coal clearance system. The difficulty is to design a system that has sufficient capacity to support production, without over capitalising or incurring high operating costs. The need to allow for a series of largely unplanned events in the design of a coal clearance system makes simulation modelling an ideal technology to employ. Simulation modelling is a methodology that allows a system with interacting components to be modelled over time, while explicitly taking into account unplanned events that may disrupt operations.This paper discusses how dynamic simulation models have been used to assist in the design of coal clearance systems. Typically this type of modelling has been used to look at the likely profile of production rates from the Longwall shearer and to determine how well various proposed combinations of belts, bins and stockpiles would support production.

Sep 26, 2011

he Wyalong goldfields were discovered in September, 1893, Messrs. Neeld and Sons, owners of the principal mine, being the pioneer prospectors. During the earliest days of the field the ore was sent to Barmedman, a distance of eighteen miles, for treatment at a battery there. The field rapidly increased in importance, and it was not long before a public battery was established on the spot. After some considerable quantity of ore was treated by this process, it became apparent that battery treatment was quite unsuitable for the richer ores, involving, as it did, considerable loss in the tailings. Recognition of this fact led to the erection, in 1895, of plants by the Wyalong Chlorination and Cyanide Works, owned by Mr. Walter Sully, for treatment by their processes; followed, at a later date, by Messrs. Neeld and Sons Chlorination Works. The Wyalong Chlorination and Cyanide Works, after a delay of twelve months in the erection of their plants, have since catered continuously up to the present time for the requirements of the field.Their plant consists of a No. 3 Gates' rock·breaker, a revolving dryer, a No. 5 Krupp mill, revolving roasting furnace with finishing hearth, two chlorination vats of 20 tons capacity each, "nine cyanide vats of 30 to 100 tons capacity, two Wheeler pans and three chlorine generators. The ores are purchased outright on assay at a fixed scale of charges, and treated by the owner of the works on his own account.

Jan 1, 1903

By L McCallum, G Dale, B Silverwood, T Roscoe, A Costin

The introduction of Progressive Closure and Rehabilitation Plans (PCRPs) in Queensland from 2019 places greater importance on planning and implementation of mine rehabilitation activities. The progress and outcomes of progressive rehabilitation activities is monitored and reported upon to demonstrate success in achieving progress towards the approved post-mining landform, and to inform corrective action where required. The requirements of PCRPs place additional emphasis on mine sites to quantify the risks of successfully achieving planned outcomes. This is particularly challenging given mined-land rehabilitation is a complex process involving decisions on multiple inter-acting management interventions, climatic conditions and spatially variable site characteristics.

Aug 2, 2023

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Today's emphasis on the enterprise bargaining process must be seen as an opportunity for organisations to further develop occupational health and safety standards at work. In particular, this shift from a centralised industrial relations system to employer, employee bargaining, presents organisations with an excellent opportunity to develop OH & S at the `shop floor' level. This is despite real difficulties in presenting hard data on the cost benefits. Unfortunately, examination of enterprise agreements ratified by the Australian Industrial Relations Commission (AIRC), show that less than 32 per cent contain provision for occupational health and safety. Those addressing the issues of occupational health and safety have included segments such as: ò rehabilitation activities; ò a new emphasis for workplace occupational health and safety committees; ò formalising procedures related to hazard identification and control; ò the use of personal protective clothing; and ò occupational hygiene and health monitoring issues. For example, an enterprise agreement reached between CIG-Gases and their unions, included clauses which commit employees to attending ten safety meetings and two work place inspections each year, in order for them to receive any further pay rises.

Jan 1, 1995

By Laing W. P

Sedimentary structures are described from the WiIlyama Complex, New South Wales. Their presence confirms lithological layering within the metasediments as bedding. These primary structures occur not only in low grade rocks as previously reported by other workers, but also in areas of medium and high grade metamorphism.Sedimentary structures include graded beds, cross beds, ripple marks, and ball and pillow structures.The observed parallelism of the early schistosity and bedding in the Broken Hill area has previously led to the idea of transposition by isoclinal folding.In the areas mapped, small scale transposition is precluded on the basis of1. uniform facing of sedimentary structures over wide areas, and2. the existence of large areas in which the early schistosity is oblique to bedding.

Jan 1, 1975

An Application of Depressant BK510 in Separation of Molybdenite and Bismuth by Flotation

Sep 13, 2010

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

By B J. Beven, A Vatandoost, J Young, S Campbell-Hardwick

The intrinsic value of iron ore depends on its physical and chemical characteristics. For example, silica and alumina are unwanted elements, downgrading iron grade and adversely affecting high temperature processing, attracting penalties in smelter contracts. For this reason, an informed knowledge of processing characteristics and product quality of the ore is valuable and cost effective during mine planning and processing.Ore variability is a significant factor that affects metallurgical behaviour and efficiency of ore processing equipment. Ore of sufficient chemical and physical quality needs to be modelled, mined, processed and usually blended. Feed and product assays are commonly used to assess potential ore upgradability. However, assays alone cannot be all informative of actual processing response given the variability of the physical properties of the ore.This study investigates the potential benefit of implementing a geometallurgical approach during the commissioning stage of the Kings deposit, part of the Solomon Iron Ore project in Western Australia. Kings drill hole database information, ie geological, textural and geochemical data, together with the results of metallurgical test work were used for geometallurgical analysis and modelling. Three main ore types were identified at Kings, namely channel iron deposit (CID), bedded iron deposits (BID) and Detrital Iron Deposit (DID). Additional classifications were utilised to better characterise these units in terms of their physical properties.Bulk sampling for each ore type was carried out across the deposit for metallurgical testing. Multivariate statistical models were developed for prediction of product quality for each geometallurgical unit. A new approach for modelling yield based on ore upgrade factors is introduced. These models were then applied to the Kings regularised mining model to assess product quality across the mining blocks and to plan product stockpiling and blending strategies.CITATION:Vatandoost, A, Beven, B J, Campbell-Hardwick, S and Young, J, 2013. A geometallurgical approach for iron ore product evaluation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Camier R. J, Perry G. J

Extensive deposits of brown coal exist in the Gippsland Basin, primarily in the Latrobe Valley. The total quantities of economically winnable coal in this region of Victoria and in other smaller fields are large enough to adequately assure Victoria's future electricity needs and to also provide large quantities for alternative applications, including liquefaction. As a result of the recent conflict in the Middle East attention has again been focussed on the production of synthetic fuels from coal. There have been many investigations over the years into the production of oil from Victorian brown coal. The purpose of this paper is to summarise the scope, objectives and major findings of these studies, with the emphasis on the direct hydrogenation route for converting brown coal to oil. The principal alternative processes are carboniastion and hydrotreatment of the product tar, or gasification and Fischer Tropsch synthesis of liquids from the product gas. The attractions of Victorian brown coal which have encouraged these studies include: ò the vast reserves of Victorian brown coal and the favourable conditions for low cost mining, ò the high quality of the coal (low ash, sulphur and nitrogen contents), ò the high reactivity of the coal giving high yields of product in hydrogenation to liquid fuels, ò the extensive data base available on the resource and its characteristics, and ò the availability of a skilled workforce and extensive infrastructure in the Latrobe Region to support a major resource development project. These advantages have been partially offset by: ò the high moisture content of the brown coal and the cost of drying, and ò the priority previously given to electricity generation in the allocation of the brown coal resource.

Jan 1, 1992