Search Documents

By Freeman C, Dingley W

Addition of sodium nitrite-borax, sodium hydroxide, sodIUm carbonate, lime, or sodium silicate reduced wear of forged steel balls and cast iron slugs in wet grinding a complex zinc-lead-copper sulphide ore in laboratory ball mills. Maximum wear reductions were 27 per cent (forged steel balls) and 33 per cent (cast iron slugs) with sodium hydroxide and nitrite-borax additives respectively.Potential measurements of balls and slugs during grinding, and analysis of the data in terms of corrosion theory demonstrated that corrosive wear had been reduced or prevented by these additives. Actual per cent wear reductions were not equated to the rate of corrosive wear because of the undefined interdependence between abrasion and corrosion in wear processes. The investigation verifies that in laboratory ball mills corrosion is significant in the wear of grinding media and wear can be reduced by corrosion inhibition and pH adjustment.

Jan 1, 1978

Distal air-fall ashes are widespread deposits that may record volcanism many hundreds of kilometres from their source. They are characteristically thin, fine-grained and have a low preservation potential usually being either eroded, or reworked and incorporated in overlying sediments following deposition. The most likely sites of accumulation are deep sea, lake and swamp environments where low energy conditions favour preservation. Post-depositional alteration of predominantly glassy volcanic ash is commonly extensive hampering identification of such layers in the geological record. As a result air-fall tuffs are poorly represented in the rock record and furthermore are commonly misinterpreted. Southeast Queensland during the late Triassic hosted active silicic volcanism and a number of fault-controlled basins in which coal-bearing sediments were accumulating. Silicic volcanics of late Triassic age are represented by the Brisbane Tuff in the Brisbane city area, the Chillingham Volcanics to the south of Brisbane and extending into New South Wales, the North Arm and Mount Byron Volcanics to the north of Brisbane, the Aranbanga Beds exposed around Gayndah and the Agnes Waters and Muncon Volcanics which occur northwest of Bundaberg. Stephens (1986) interprets these Volcanics as the remnants of a major silicic igneous 'province which he likens to modern continental orogenic margins. The Ipswich, Tarong and Callide Basins of southeast Queensland all contain coal measure sequences of late Triassic age that accumulated in alluvial plain environments. A Dicroidium flora is common to all and palynol.ogical evidence indicates a late Triassic (Carnian) age (de Jersey, 1975; Stevens, 1981). The coal seams of the three basins are characterised by their thickness (up to 25 m) and the presence of abundant thin, laterally persistent, kaolinite claystones (tonsteins) that show a marked similarity of morphology, texture and mineralogy. Detailed studies of the Ipswich Coal Measures (Falkner, 1986) suggest a volcanic air-fall origin for the tonsteins of the Ipswich Basin. Similar.tonsteins from the Tarong and Callide Basins provide evidence for widespread silicic volcanism during the late Triassic in southeast Queensland.

Jan 1, 1987

By C Quirion

Agnico-Eagle Mines Limited, Laronde Division, operates the deepest single-lift shaft in the western hemisphere. The initial Penna hoisting plant was designed for a production rate of 1800 tonnes per day (t/d) from a 2240 m deep shaft. Exploration success, while sinking the shaft, led to a decision in 1998 to increase the production rate to 4500 t/d of ore from a loading depth of 2200 m. The new production rate was achieved by increasing the size of the rope and reducing the rope static factor from the existing 5.0 required by regulation to a static factor using the formula 25 000/(4000 + L) contained in a draft document that would eventually become SABS 0294 in South Africa. The formula permits Laronde to use a static factor as low as 4.0. The upgraded Penna hoisting system is the first hoisting plant outside of South Africa to meet the South African requirements. This paper describes the conversion of the hoisting plant to the lower rope selection factor in the year 2000 and the operating and maintenance issues experienced since then.

Jan 1, 2005

The perennial challenge facing mining and minerals operators is to improve productivity, usually by a combination of cost reduction and performance improvement. In a typical production situation involving mining and processing activities, the standard approach has long been to seek improvements in each activity, effectively in isolation from each other. However, the realisation is growing that there is considerable potential to achieve really substantial productivity gains by much improved integration of mining and processing with the key being to consider what is best in the total sense. Some of the linkages between fragmentation in mining and downstream processing are considered in this paper. These linkages involve technical, operational and economic Considerations.

Jan 1, 1997

By Grace NC, Lightfoot BW

Small scale trials of the smelting of a copper concentrate in the Sirosmelt submerged lance reactor are described. Pellets of concentrate were dropped into the reactor while injecting air-rich mixtures of oil and air through a lance into a bath of matte overlain by slag. This produced a discardable slag and a matte which was converted in sequential stages in the same reactor to white metal and blister copper. Difficulties were encountered in determining the end points of the converting stages but control techniques were developed to allow successful operations producing blister copper. Deportments of minor constituents of the concentrate to slag, matte,metal and fume for the three stages are reported and possible applications are Discussed.

Jan 1, 1980

This paper describes the characteristics of blasting which set it apart from other methods of breaking rock. The mechanism of rock breakage and the influence of rock proper- ties are then discussed. The strain and fragmentation produced by a cylindrical charge does not change once the charge is longer than 16 blasthole diameters. The influence of bench geometry, charge length and drill diameter are then examined. It is shown that spherical charges have advantages over long slender cylindrical charges. By selection of the appropriate drill diameter, explosive and charge configuration the optimum blasting practice for a given rock to give suitable fragmentation and muckpile profile for sub- sequent handling can be found. The fragmentat- ion depends not only on rock and explosive properties but also on the pattern which dictates how effectively the cracking is utilised. The size distribution of the fragments is given by the Rosin - Rammler equation. Undesirable cracking of the rock in the final wall can be controlled by the careful design of blasts as they approach the final wall. Finally, it is concluded that because of the distance to which blasting can fracture and then displace rock it is suited for the breakage of large volumes of rock.

Jan 1, 1978

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

The preconcentration of uranium ore by radiometric ore sorting at Mary Kathleen Uranium Ltd. is described. The operation of the ore sorting machines is discussed in detail and performance results obtained with the existing system are presented.

Jan 1, 1978

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003

In a stipulated hard rock situation, drilling and blasting costs per tonne in open cutting or underground operations are comparable. In open cuts the drilling and blasting costs per tonne of ore are multiplied by the waste ratio.Conventional underground loading and haulage practices are so batch-oriented that the cost per tonne of ore handled is a large integral multiplier of open out costs per tonne loaded and hauled.If underground costs are to be reduced to compare favourably with open out costs then loading and hauling practices underground must be converted to a non-batch continuous system. This can be achieved by utilising gravity to control ore to mobile crushers feeding conveyors running direct to surface.

Jan 1, 1985

By Pooley F. D

The coal measures of the South Wales coalfield contain at least 50 horizons at which coal seams are known, to occur. More than 300 samples of coal were collected from these coal measures and this paper outlines thefindings of an investigation of the pattern and distribution of 12 trace elements in South Wales coals. A comparison of trace element contents of the South Wales coals is made with trace element values found elsewhereand an attempt was made to establish the organic affinity of the elements in different seams and in the coalfield 'as a whole. An important function of such an analysis is to determine the order of abundance of trace elements and this was performed for individual seams and for the whole coalfield.The interrelationship of certain elements in some seams is also examined with a view to understanding the effectiveness of such an approach to seam correlation.Ranges of values are quoted together with the mean values of the various elements. Variations of elemental values within a seam section and over the coalfield as a whole are discussed.

Jan 1, 1977

Very little has been written about the discovery and early history of prospecting of ironstone deposits in the Iron Knob-Middleback Range area of South Australia, the main source of supply of ironstone (hematite) for the Australian steel industry, and scanty though the record is, much of it is wrong or misleading.With the help of several people, to whom acknowledgement is made at the end of the paper, the writer has unravelled some of the story, but not the whole story. It is hoped that publication of this paper will stimulate interest in others, who may be able to supplement this account from family records, from the files of newspapers, or from archives.

Jan 1, 1969

By J Wei, X Lan, F Wang

This paper presents a quantitative assessment model for the assessment of environmental load in gold production, which is based on environmental ecology, Life Cycle Assessment (LCA) and artificial neural network. In LCA evaluation indexes include resource consumption, energy consumption, gas waste, liquid waste, solid waste and so on. Each item represents an aspect in gold production while their combination reflects the relationship between gold production and environment. In this paper an utility function of evolution index on environmental load is given by linear or non-linear transformation, which changes evaluation indexes with different dimension into an equivalent value in range of [-1, 1]. This paper also provides a new approach to make decision on the weight for quantitative assessment with the help of a three-layered artificial neural network. The proposed approach in this paper has been successfully used to a real synthetic assessment for the environmental load in gold production, which include seven kinds of different operational technologies in China. The applications prove that the new approach is successful and reliable. It provides a new tool for the assessment of environmental load of the gold production.

Jan 1, 2003

Vitrinite reflectance forms the basis of a study of coal rank variation in two areas of the Upper Hunter Valley, New South Wales, on the northern margin of the Sydney Basin. A selective analysis procedure, based on samples rom twenty-two boreholes, has resulted in a small range of reflectance values for each sample and consequently a high degree of significance for calculated mean values. The patterns of rank distribution derived from these data have facilitated an interpretation of the rclative timing of coalilication and deformation in each area.This study provides support for the suggestion by several authors that there were at least two periods of folding in the tJpper Hunter Valley. In the Hebden-Ravensworth area, minor folding took place after most of the coalilication was completed.To the west, in the region of the Muswellbrook Anticline, coalification occurred during or after the formation of this major structure. Tectonic instability during deposition of the Singleton Super-Group, in the region of the Hunter-Thrust on the basin margin, is evidenced by rank variation suggesting differential subsidence across this zone.

Jan 1, 1980

An assessment of methods currently available for the accurate determination of low concentrations of platinum in ores and mineral concentrates indicated that prior treatment of the sample by fire assay procedures is necessary. To enable rapid determinations to be carried out, instrumental methods applied to the metallic bead produced from the fire assay treatment have been evaluated, considering maximum flexibility for concentration variations, minimum chemical operations, and adequate sensitivity.Atomic absorption spectrometry proved suitable, giving solution determination limits of 0·4 p.p.m. Pt, 0·1 p.p.m. Pt, or 0·06 p.p.m. Pt under various extraction conditions using aqueous and organic agents. Thesedetermination limits related to 1 assay ton of sample (32·67 g) produced easily readable and accurate readings within the range of platinum contents (0·03-2·0 p.p.m.) of economic interest in deposit evaluation and prospecting. The technique shows promise of also being suitable for determination of palladium and gold.

Jan 1, 1970

These may be of interest to members examining the collection of ores, etc., from Mount Lyell, which is a feature of the Victorian Gold Jubilee Exhibition, and may have some value as geological records. No. 7 and No 8 are analyses of samples of footwall rock from the Lyell Tharsis mine. No. 7 is hard, crystalline, fine-grained, and of homogenous structure. It has a dark-red colour, due to ferric oxide (Fig 1); and was taken from a place eight feet east of the ore body and about half way between the 50 feet and 100 feet levels. No. 8 is from the same excavation and from four feet east of the ore body it is softer than No. 7, being easily scratched with a knife-blade, of a deeper dark-red colour, and has a slaty cleavage.

Jan 1, 1902

Magneto flotation is a recently developed method aimed at simultaneous utilisation of the magnetic and flotation properties of minerals in separation processes. In this method, magnetic minerals are prevented from reporting to the froth product while non-magnetic minerals are being floated. With suitable ores, this makes it possible to reduce or entirely eliminate the cleaning and scavenging operations that are otherwise necessary in conventional flotation and magnetic separation systems. This paper describes the testing of magneto flotation on a Canadian magnetite ore. The ore sample used in the experimental work contained a total of 32.89 per cent Fe of which 87.60 per cent was magnetic in the form of magnetite. Magnetoflotation yielded, in a single step, a final concentrate assaying 69.10 per cent Fe and with an overall recovery of 84.84 per cent representing a magnetic iron recovery of 96.39 per cent. Comprehensive comparisons were made with conventional magnetic separation and flotation, and it was found that with these methods at least four processing steps were required to achieve results similar to those obtained with single-stage Magnetoflotation.

Jan 1, 1993

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

On the first of October 1991 two significant pieces of legislation came into force. Both of these are relevant to the allocation and use of minerals in New Zealand . They are the Crown Minerals Act 1991 and the Resource Management Act 1991.   The full legal implications of these is not fully known because the Planning Tribunal and the superior courts have not as yet had to deal with them in any detail. However, the thrust of the legislation is clear and it is appropriate to give an overview of how the statutes will operate in tandem if you are seeking to pursue or oppose any prospect, exploration or mining of Crown Minerals in New Zealand.

Jan 1, 1992

The writers of these notes, having conducted some tests on the steam consumption of air compressors under varying conditions, believe that the detailed results of such tests will be of interest to the members of the Institute, and may lead to the contribution of further and more valuable information, of benefit both to manufacturers and users of this class of machinery-to the manufacturer in that he frequently has the opportunity of giving a very thorough test to the machine in the shop, and-tothe user or purchaser by making clear to him what may be reasonably demanded of a high-class machine. It must be remembered that, though of the highest importance, a low steam consumption is but one of the many features of a high-classmachine; for the present, however, it has been considered advisable to confine the paper chiefly to the first-mentioned aspect, with such information concerning the air ends as is obtained along with the steam consumption tests. Unfortunately, too few of these tests are conducted, and but few results are published, therefore the writers feel that no apology is needed in bringing their results before the members.Some nine months ago the Brilliant Extended G. M. Co. was supplied with a compressor by Messrs. Thompson and Co., of Castlemaine, and with the object of testing its actual performance.

Jan 1, 1907