Search Documents

By De Jong HJ

During the forthcoming reline of No.3 Blast Furnace at the Newcastle Steelworks of the Broken Hill Proprietary Co. Ltd., facilities for the screening and weighing o' coke will be installed. The equipment is needed to optimise the sizing and the quantity of coke immediately prior to it being charged to the furnace. Up till the time the furnace was blown out in November, 1982, coke was charged to the furnace by volume, ie by skip fulls only. This resulted in variation to the ore/coke ratio charged due to bulk density changes and erratic skip filling levels. This in turn affects the heat balance of the furnace and causes fluctuations in hot metal chemistry and temperature. A coke rate penalty has to be paid also. Coke layer thickness in the furnace burden cannot be controlled closely, resulting in loss of control over gas distribution in the furnace. A grizzly type screen was incorporated in the skip loading chute but this ineffective method left a great amount of fines with the coke being charged to the furnace. Furnace permeability was therefore reduced, particularly in the hearth.

Jan 1, 1984

To counter depressed world nickel prices, a continuing effort is being made at Kalgoorlie Nickel Smelter to reduce unit production costs. One major area in which production costs can be reduced is the substitution of coal for fuel oil. Two areas where this has been achieved to bring about a saving are, the addition of coal to flash furnace flux to reduce supplementary fuel oil requirements in flash smelting and the replacement of two oil-fired air preheaters with a coal-fired unit. These actions have resulted in coal replacing 67% of the current fuel oil requirement in flash smelting at the Kalgoorlie .Lckel Smelter.

Jan 1, 1987

The detailed work done by Stillwell and Edwards on the occurrence of cobaltite and safilorite-Iollingite at the South Mine, followed by its presentation as a paper to the Institute, calls for, a few notes on its occurrence elsewhere in the Broken Hill field. No massive cobaltite similar to that in the South Mine veinlet is known except from the Consols Mine (as mentioned in the paper). Fine grained cobaltite has, however, been found in low-grade ore from the North Mine. Microscopic grains occur in a mineralized green feldspar pegmatite. The feldspar has been replaced in part by graphite, and the cobaltite occurs in association with the graphite. In its hardness, pinkish-white colour, and resistance to the standard etchingqeagents it is similar to the South Mine cobaltite; it is etched by acid permanganate solution. An interesting feature of this occurrence is the way in- which some of the minerals (notably galena) have forced apart the graphite lamellae in crystallizing, forming lenses enclosed by the curved cleavage surlaces 0;[ the graphite.StillwelI and Edwards cite a note by G. Smitht for the statement that "cobaltite has been recorded from the Australian Broken Hill Consols Lode in the vicinity of the rich silver deposits, though not in contact with them."Smith, however, is here referring to the oxidized zone. Elsewhere in the same article he states "... a deposit of cobaltite in a very much altered condition was found. This was impregnated with silver, and assayed as high as 3,000 ounces," Of the cobaltite in the unoxidized zone, Smith simply states that it became rarer with depth.Cobaltite has also been recognized by Mr. H. F. Whitworth, M.SC., Curator of the Mining Museum, Sydney, in specimens from Burt's Copper Mine eight miles south of Broken Hill.

Jan 1, 1944

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By H Höft

Today tunnel segment liners are sealed with corner-vulcanised gaskets made of extruded elastomeric compression profiles. The profile geometries and the elastomeric materials have been further developed in course of time to meet the steadily increasing water-proofing requirements. After 40 years of using such compression gaskets, a wide range of proven standard profile geometries and well-known brands can be found on the market. Even so, there is still potential for further developments and improvement, not only with regard to the water-proofing performance. Permanently increasing cost pressure in the segment production plants demands further developments and new solutions with regard to application techniques. This is an abstract only. No paper was prepared for this abstract.

Mar 8, 2011

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

(Quality can be defined as that which is acceptable to the market and can be supplied with a predictable degree of uniformity and dependability at a low cost. The market for any mining product is downstream processing, whether it be an alumina refinery, a gold processing plant or a flotation plant. The cost of that downstream process is partly dependent on uniformity of its feed material both in physical and chemical terms. With more operations adopting procedures which require quality assurances in line with International Standards, from their raw material suppliers, miners must look to their grade control processes to provide uniformity and predicability.This is not a new concept. The mining industry has constantly been working with ahighly variable raw material supplied by Mother Nature, from whom we cannot demand quality assurances. Through the processes of exploration, resource and reserve definition, long and short term mine planning and day to day grade control an end product has been supplied which consistently meets our customers requirements, in an economic fashion. When any of these processes fail, then penalties are incurred which can range from increased mineral processing costs to loss of markets and in the ultimate case, failure of a mining operation.

Jan 1, 1992

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By P G. Fuller

The Woodlawn Mine near Canberra faced the challenge of poor ground conditions from the commencement of underground operations 1987. Talcose shears bounded the dense massive sulphides on both the hangingwall and footwall side of the orebody. In another area the talc existed not only on the edges of the orebody but through out it as well. The country rock was relatively weak shales compounded by a low stress environment that allowed the wall rocks to fall apart quite easily. The challenge for the operators was to overcome the poor ground conditions. This was done by attacking the problem from three directions:technology, how technology is applied, human relations and leadership by all levels of the Management team, and by ensuring that these processes meshed together well.Woodlawn in it early days as an underground mine enlisted the assistance of BFP (Formerly Barrett Fuller and Partners) as a second set of eyes to assist with the assessment of the ground control procedures. The results are discussed in this paper. The progression to this end result included:non-contract payment systems; ground control training for the full range of mining personnel; the development and enhancement of cable bolting and shotcreting equipment; the development of Practical Standard Work Procedures by mine operators; and innovative use of shotcrete and cables bolts to control extremely poor ground conditions.

Jan 1, 1998

By D Monaghan

Pumping water for dewatering and water supply is a major component of electricity consumption at mining operations and hence is a significant contributor of greenhouse gas emissions. Pump systems at a typical mine site can be broadly split between above ground centrifugal pumps (generally used for water transfer) and submersible borehole pumps (generally for dewatering and/or water supply). In contrast to above ground pumps, submersible borehole pumps can be subjected to varying duty points (total pumping head and flow requirements) as a result of changing bore water levels and yields, particularly in mine dewatering bores. Typically, much higher pumping rates are required at the commencement of dewatering to remove groundwater storage and to intercept sufficient groundwater throughflow to achieve target drawdowns. Once target drawdown levels are reached it often only requires much lower pumping rates to maintain target drawdowns. Pumps sized to remove the large initial volumes of stored groundwater often end up too large for the lower flow rate required for æmaintenance pumpingÆ. This often results in pumps operating inefficiently, a problem which can be made worse when pumps are throttled to reduce the pump output to better match the reduced bore yield. Current standard operating practice places little emphasis on the electricity consumed by pumps, with the focus often being on minimising capital expenditure (æIf it ainÆt broke donÆt fix itÆ). Submersible pumps can have extended service lives of ten to 20+ years. However as the capital cost of a pump typically represents only five per cent of the life cycle cost, the vast majority of the life cycle cost is energy usage.Through the implementation of a regular review of the operation of borehole pumps, significant reductions in electricity use and associated greenhouse gas emissions can be achieved without impacting the dewatering schedule. In most cases, the capital cost of replacing pumps is more than offset by savings in operating costs. These potential savings become even more significant when considering proposed future carbon tax levees.This paper presents examples of the opportunities for significant reductions in energy, greenhouse gas emissions and overall costs that can be achieved for a range of dewatering scenarios.

Jan 1, 2009

By M J. Newton

As part of the AMIRA P843 project Keeney and Walters (2008) describe how the principal components analysis (PCA) method can be used to identify classes of samples with similar metallurgical characteristics. However PCA does not take account of the location of each sample in 3D space. This paper describes a study to analyse the spatial distributions of the classes and determine appropriate modelling methods to control the estimation of the comminution parameters and mill performance indices into a 3D block model. This includes but is not restricted to geostatistical techniques that are used for grade modelling. The starting point for the study is the class definitions and the regression models for estimating the comminution parameters and performance indices. Each sample is assigned a class and the spatial distribution of each class has been analysed using different techniques including the calculation of variograms. This establishes whether the classes can be used as domain control for estimation into the block model – a procedure similar to using geological rock type domains for controlling the estimation of grades for a resource model. However, standard geostatistical estimation methods such as ordinary kriging assume that the variable being estimated is additive or linear. This assumption is valid for variables such as grade but this is not necessarily the case for the comminution parameters or the performance indices. Therefore the estimation procedure must either use variables that are definitely additive or the effect of potential non-additivity must be tested and accounted for where possible.The results of the study show how performance indices such as recovery, throughput and specific power can be estimated into the block model. This model is then combined with the geological model to provide a multi-parametric model that is used to optimise the mine planning and scheduling activities which can lead to significant improvements in NPV.

Sep 5, 2011

By O Dominguez

Mine value chain reconciliation (MVC) is a necessary procedure to evaluate a mine’s performance against the assumptions and models used to plan mining and processing operations. Using nomenclature from Parker (2012), F2 reconciliation is the ratio between material received at the mill, compared with material sent to the mill, commonly reported in terms of tonnes, grade and metal. Measurements of material sent to the mill can be estimated in many ways, including: fleet management system (FMS) records, truck counts, or volume reduction. Most time-based reconciliations (for example, month-end reconciliation) use short-term model depletions of in situ rock measured by periodic topographic scans or surveys.

Mar 22, 2022

By Kelley BC, Filmer AO

The chemical oxidation kinetics of sphalerite by Fe(III) was studied at various temperatures and size fractions in sulphate media. The kinetics of Zn extraction followed a pore diffusion control mechanism with an apparent activation energy of 54-58 kJ mole. This figure, although high for a pore diffusion control process, is consistent with other studies carried out in sulphate media. An empirical statistical model, relating the extraction time to % Zn extraction, average particle size and temperature, is described by log 1 = 12.22 - 0.017% Ext. - 1.76 log D Av t - 2954 T Parallel studies were also carried out investigating the biological oxidation of sphalerite utilizing the acidophilic autotrophic bacterium Thiobacillus Ferroxidans. The effect of such kinetic parameters as pulp density, particle size and Fe(III) on bacterial growth rate and consequently zinc extraction rate, were studied and where appropriate, optimum conditions for bacterial growth were specified. Based on the results of chemical and biological leaching studies, it was apparent that rapid zinc extraction from sphalerite was predominently due to oxidation by Fe(III). The biological oxidation process catalyses the oxidation and regeneration of Fe(III). The proposed combined chemical-biological leach system was simulated in semi continuous fashion. The sphalerite oxidation rates obtained in this system were similar to that predicted by the chemical leach empirical model. 1. Senior Research Metallurgist, CRA Research, Boolaroo, N.S.W. 2. Group Leader-Hydrometallurgy, CRA Research, Boolaroo, N.S.W. 3. Senior Research Scientist, Biotechnology Australia, Roseville, N.S.W. 4. Senior Experimental Officer, Biotechnology Australia, Roseville, N.S.W.

Jan 1, 1986

By McLeod RL

The Mt. Morgan mine, located 36 km SSW of Rockhampton, Qld at Lat. 23¦38' S, Long. 1500 22'E, is hosted by a Middle Devonian sequence of acid volcanic rocks and sediments. The Upper Nine Mile Creek (UNMC) prospect, 14 km SE of the Mt. Morgan mine, is in an ap- parently equivalent sequence of rocks. The Late Devonian Mt. Morgan Tonalite separates the two areas. The Mt. Chalmers mine, located 27 km NE of Rockhampton at Lat. 23¦ 18' S, Long. 150039'E, is hosted by the Early Permian Berserker Beds. These three volcanogenic massive sulphide deposits show pronounced similarities in their host rock lithologies and stratigraphic-struc- tural settings.

Jan 1, 1987

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

By Morland R, Peck R

The Joint Committee of The Australasian Institute of Mining and Metallurgy (AusIMM) and the Australian Mining Industry Council (AMIC) have published a Code for the Reporting of Identified Mineral Resources and Ore Reserves. The Code is the result of an initiative begun in 1971 to achieve industry self regulation of Resources and Ore Reserves reporting which resulted first in guidelines for reporting standards but which have now been incorporated in ASX Listing Rules as a Code with significant sanctions ensuring compliance. This paper describes the background to the Code, its key provisions, and comments on practical aspects of working with the Code and compliance issues.

Jan 1, 1990

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Methane is present in varying degrees in nearly all underground coal mining operations. At mixtures with air near 5-15% it is explosive and consequently since it is not usual for these levels of contamination to be reached in the general body of a mine ventilation system it is not unusual to experience it in specific places. On longwall faces the most used power loader is the shearer machine and because of its general shape, situation and operation it is likely that all the factors which are required to cause a frictional ignition can be present. This paper makes a general appreciation of the causes of these ignitions and methods which are and have been used to control these situations on and around these machines.

Jan 1, 1981

By D Semini, B Newcombe

Base-metal sulfide refractory gold ores often contain a portion of ‘free’ gold that is amenable to recovery using gravity concentration methods, whilst the refractory portion of the gold is better recovered using flotation. The decision as to whether a plant treating a refractory gold ore should utilise gravity concentration or a flash flotation circuit (or a combination of both) within the grinding circuit is usually made at the design stage of flow sheet development. Very limited data is available in the published literature which provides an industrial scale comparison on which to base such a decision and conventional laboratory testing methods are often the only way of obtaining such data. The optimum processing route will also be mineralogy dependent.This paper presents the findings of operating a refractory gold plant with either flash flotation (normal operation) or a combination of flash and gravity recovery methods treating the cyclone underflow stream and will demonstrate the regions of the recovery profile that each contributes to. Size-by-assay analysis has been performed on a number of streams around the operating plant to gain an insight into the changes that occur when the gravity circuit is in operation in addition to the flash flotation circuit. A discussion around the implications to overall plant operation in combining the use of a batch process (gravity concentration) with a continuous process (flotation) is presented.CITATION:Newcombe, B and Semini, D, 2014. Interactions between flash flotation and gravity concentration – an industrial case study of a refractory gold concentrator, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 427–436 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By J Franke, C Gonzalez

One of the regular tasks of geotechnical and mining engineers is the measurement and management of deformation in underground excavations. Although several methods are used to do so, the incumbent methodologies for monitoring deformation and ground support serviceability are limited to the use of visual observations or measurements at discrete points, resulting in a qualitative assessment only. The introduction of LiDAR technology allows a quantitative assessment across the entire excavation volume and its rock surface, by collecting a full three-dimensional image of the entirety of an excavation such as an underground drive, decline, or a tunnel. Comparisons between epochs of complete 3D data coverage allows for change detection over time that doesn’t feature otherwise typical omissions. The implementation of regular scanning has shown to be highly advantageous for mines with swelling or squeezing ground, but also at mines with rapid deformation. Despite the LiDAR potential, its adoption has been slow. A key reason for that is that working with point clouds is foreign to most geotechnical engineers. Point clouds have long been the realm of surveyors, but to fully adopt their use in geomechanics requires retraining, upskilling, and devotion by the individuals and the company. Sites are already stretched, so often there are insufficient resources to be applied to bringing the new technology into use. The solution to this hurdle is to partner with subject matter experts to achieve the desired high-quality outcomes without the commitment of time by geotechnical personnel. This paper presents a new solution of fully automated raw LiDAR point cloud data processing that not only enables geotechnical engineers to avoid having to learn unrelated skills by allowing for deformation monitoring without associated training or expertise, but it also provides instant reporting results as well as a sophisticated database with features otherwise not available. All data processing time and effort is completely replaced by an automated process which at the same time opens up the opportunity to monitor many more excavation volumes at a higher frequency than is possible with conventional tools and methodology.

Nov 29, 2022