Search Documents

By Lownds C. M

Several classes of commercial explosives and blasting agents behave non-ideally, especially in diameters near their critical diameter. A direct and convenient measure of non-ideal behavior is the detonation velocity (VOD); if the VOD is less than the ideal value, usually obtained by calculation, then the explosive is detonating in the non-ideal mode. Such lowering of the VOD is usually due to both lateral loss of energy and post-CJ release of energy. The second of these factors, namely slow release of chemical energy, is of most interest in blasting. While the observation of a low VOD clearly suggests slow reaction of part of the explosive composition, it does not necessarily mean that the energy is lost to the overall rock-breaking process. The partition of the energy of the explosive into various useful and wasteful categories is considered. Simple models of energy partition in blasting, and of explosive reaction kinetics, are presented. The models consider the effect of explosive type and rock type, the explosive being described in terms of the most common phases namely liquid, air bubbles, porous ammonium nitrate, dense or crystalline ammonium nitrate, and aluminum. Over a range of combinations of the above phases, the model predicts reasonable critical diameters and VOD's. Results are presented which show the effects of non-ideal detonation on fragmentation and heave in different rock types. Conclusions are drawn about those blasting conditions in which ideal behavior is beneficial, or Disadvantageous.

Jan 1, 1990

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By J Bower

The JORC Code does not specify a definition for ælevel of confidenceÆ. The common approach in the mining industry is to use a certain drill spacing or number of data samples to classify resources by the confidence categories. Another approach includes application of the quantitative geostatistical criteria for non-subjective and consistent definition of the resource categories. This approach, which has become increasingly popular in the mining industry, provides a quantitative measure of the resource estimation uncertainty. In this study, uncertainties associated with the different drilling grids at the Weipa bauxite deposit (Queensland, Australia) have been modelled using conditional simulation methodology. Criteria used at Weipa for defining resource categories are as follows: mineralisation can be classified as a Measured Resource if tonnage and grade of its volume representing three months of production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability, ie two standard deviations); and mineralisation can be classified as an Indicated Resource if grade and tonnage of its volume representing annual production can be estimated with a precision error not exceeding ¦10 per cent (at 95 per cent probability). Several different grids have been created by subsampling the drill hole database. The studied variables include Al2O3, SiO2, thickness of the bauxite seam and location of the footwall contact. The variables have been modelled by sequential Gaussian simulation. Based on this study the following drill spacings have been recommended: Measured Resources û 150 m by 150 m, Indicated Resources û 300 m by 300 m.

Jan 1, 2009

By P B. Hills

Increasingly over the past couple of decades, the importance of understanding the in situ stress regime in underground hard rock mines has become accepted by all. Providers have responded to this requirement and various techniques for undertaking the measurements have been honed while others have slipped from use. It is a simple, though not inexpensive task to engage a provider to undertake the require measurements, and a comprehensive report will ensue. So, what has actually been obtained? What should the geotechnical engineer do next? What tools are necessary to do so? Regardless of the method of measurement, the report will describe the location of the measurement site and describe the basis of the methodology used in undertaking the measurements and a log of the measurement program. Finally, it will include the results, which should incorporate the normal and shear stress components of the full stress tensor. Ground control management plans (GCMP’s) and stress summary reports and spreadsheets prepared by site geotechnical engineers always include the magnitude, trend and plunge of the principal stresses. Remarkably few site-based summaries include the full stress tensor. This is a significant gap as the full stress tensor is vital for any further data manipulation. However, without the algebraic tools to undertake those manipulations, their value is diminished. This paper seeks to provide a checklist of ideas to be considered. It provides commentary on the options available to dissect the stress measurement report and ensure that the maximum possible value is derived from it. The manipulation and presentation of component stress data is also discussed. The various methods of stress measurement are not the focus of the paper but some of the strengths and weaknesses of them over which the site geotechnical engineer has some control, are highlighted.

Nov 29, 2022

By T C. Hughes, R Hughes

Ausmelt has developed and commercialised high temperature reactor technology that has been applied to waste processing in the form of a catalytic waste converter (CWC). Ausmelt Technology uses a top submerged lance system within a versatile converter containing an oxidised molten siliceous slag. Metals and other valuable products can be extracted from wastes for recycle into the community. Non-valuable components such as toxic organochlorinated compounds are destroyed and prevented from reforming. The slag produced is inert and can be safely used in building and concreting. The CWC can be applied to practically all types of wastes and examples from Ni-Cd batteries to toxic wastes are discussed. Additional benefits can be derived from large-scale operations if the surplus heat generated is exploited to produce steam and electricity.

Jan 1, 2000

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Z Lianbi, Z Yibin, Z Youhong, P Bin

Without adequate soil available, it is difficult to rehabilitate a large area of acid mine waste dump with sustainable plant communities, which has a strong potential acid generation. In the present project, paste tailings capping method has been put forward to reconstruct plant ecosystem on acid mine waste rock dump. This rehabilitation method uses paste tailings as capillary break and plant growth media. The tailings used contained 26.3 per cent of particles of less than 20 ¦m which satisfy the requirement of grain of paste tailings preparation. The tailings are not acid- producing materials. In addition to Cu, total contents of Zn, Pb, Cr, Cd, As and Ni in tailings are lower than those in local soil. Paste tailings concentration 70 per cent ~ 72 per cent was prepared by concentrating ten per cent tailings by using polypropylenecrylic sodium as flocculation. The potential pollution risks are low by using paste tailings as capillary break layer. Plants directly grown in the tailings did not particularly accumulate Cu, Zn, Pb, Cr, Cd, As, Ni in roots, stem and leaves, which were 0.01 ~ 1.6 times of those grown in soil.CITATION:Yibin, Z, Lianbi, Z, Bin, P and Youhong, Z, 2012. Study on paste tailings capping ecology reclamation on acid mine waste rock dump, in Proceedings Life-of-Mine 2012 , pp 243-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Winrove G. S, Herdie G. J, McCarthy C. A

Production of hot metal from the Hlsmelt Research and Development Facility at Kwinana, Western Australia commenced in October 1993. The stand-alone facility is a unique, coal-based, integrated ironworks equipped to process iron ore fines to pig iron and simultaneously undertake a wide range of research tasks. The data generated will be used to verify the commercial potential of the technology and to set the design and operating parameters for a full-scale production plant. The design, construction, commissioning and initial operation of the HRDF has required many innovative and practical solutions to be developed and implemented by the international group of organisations contributing to the Hlsmelt Project. Initial operation has produced results which demonstrate the potential of the unique process technology associated with the core plant smelting unit. The recent achievement of post-combustion levels of 60 per cent with heat transfer efficiencies greater than 85 per cent demonstrates that the performance obtained with the Small Scale Pilot Plant in Maxhutte, Germany can be reproduced at a larger scale. The results presented in this paper support the thrust for further intensification and future commercialisation of the process.

Jan 1, 1995

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

By P A. Montoya

La Colosa is a world-class porphyry Au project located in Colombia, currently undergoing prefeasibility analysis. As part of collaboration between AngloGold Ashanti and the AMIRA P843A GeMIII Project, the application of emerging geometallurgical characterisation testing and modelling tools has been incorporated in early stages of project development. The aim of the geometallurgical study is to map inherent comminution variability across the La Colosa deposit providing information critical for mine/mill design and optimisation. In this study, site-based data incorporating multi-element assays, quantitative analyse X-ray difraction QXRD bulk mineralogy measurements, EQUOtip rebound hardness data, and routine geological logging information from 59 diamond drill holes has been integrated with a range of geometallurgically specific comminution test (ie GeMCi, A × b, BMWi). The work in this paper demonstrates the integration techniques used at La Colosa to link routine data acquisition methods with comminution test results through the development of proxy support models. The integration incorporates a range of statistical techniques including principal component analysis and regression modelling. By creating proxy models, comminution index estimates can be propagated into the geological database enabling comminution processing domains to be defined. These domains provide the first spatial representation of comminution performance and variability at La Colosa and can be compared against traditional geological domains. This study provides the foundation for ongoing comminution characterisation as the La Colosa project evolves through project cycles into an operational mine.

Sep 5, 2011

The paper reviews winder rope inspection procedures at the Non Destructive Testing (NDT) Unit of Western Australian School of Mines (WASM) and outlines measures taken to adopt the world's best practice. The measures include acquisition of a new type of rope tester, adoption of comprehensive rope rejection criteria, adoption of a standard rope inspection procedure and formal training of the wire rope inspectors.

Jan 1, 1995

By A Black, A de Jo, J Cavanagh, J Harding

Acidic and metal-rich waters have been discharging from Sullivan Mine, West Coast, New Zealand since the closure of the mine during the early- 1990s. This has resulted in a decrease in pH from a background of 4.5 to 2.8 and an increase in metallic elements in nearby Rapid Stream. In addition to the chemical effects on Rapid Stream, a study of freshwater macro-invertebrates revealed the absence of most biota downstream from the discharge. An attempt is being made to use the Sullivan Mine as a case study of problem and remediation analysis.

Jan 1, 2003

By C Vejrazka1

The occurrence of airblasts is one of the principal mining hazards in caving operations between the time of cave establishment and breakthrough of the cave to surface. As such, it needs to be managed continuously and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. The likelihood of an airblast occurring is based on a range of geotechnical factors over some of which engineers on-site only have limited control. However, the impact of an airblast to the underground mine, if it does occur, can be managed by following established safety guidelines for the production from the cave.This paper outlines how the Caving Airblast Simulation Tool in Ventsim was used to determine a risk management strategy for a sublevel and a block cave at a mining operation in Australia. The block cave has a footprint of 14 500 m2 with the extraction level located 1250 m below surface while the sublevel cave currently has a footprint of around 18 000 m2 operating between 660 m and 800 m below surface. Both caves are currently in their early operational periods. The risk analysis provided valuable information for the production planning of the caves including confirmation of extraction ratios for the block cave undercut, locations of airblast walls and maximum allowable air gaps for different muck pile heights to ensure safe operation is achieved.

Oct 12, 2022

In spite of the efforts done in the past to implement in Codelco best practice guidelines and standards on several important sampling, assaying and variability issues, many people, particularly top managers and operators, are still not aware of the relevance of the use of the principles and practice of geostatistics, sampling theory, analytical chemistry and the understanding of processes variability from rock to cathodes. As a result, an important challenge for the sampling community is to find out the causes of this lack of awareness and to develop communication skills to influence the organisation, particularly the top management level. This situation is not affecting only Codelco; it is a common characteristic of the copper mining industry. The main cause is cultural. Judeo-Christian and occidental sciences are deterministic. This implies a disregard of process variation and the assumption that homogeneity is omnipresent. Another important aspect of the cultural challenge is education. Education is the most efficient way to transfer a system of ideas, traditions and practices. To implement proper courses of sampling theory and geostatistics and support to multidisciplinary education at universities, mining companies will improve teamwork between geologists, mining engineers, metallurgists and chemists. The improvements will imply a more sustainable and efficient mining business.

Mar 1, 2010

By Finlayson J. F

The advantages of rapid and accurate analyses are becoming appreciated in many industries today and have resulted in a great increase in the number of samples received by their laboratories. This has caused some firms to consider the installation of one or more of the instruments available for analytical chemistry. In this country there are relatively few people with experience of instrumental methods and it is difficult for a firm considering the installation of such equipment to assess the advantages which instruments may give them, and to decide which instruments, if any, will be of most use to them. The object of this paper is to give a brief survey of instrumental methods in the field of inorganic analysis. Instrumental methods of analysis have numerous advantages when used correctly. They enable extremely rapid analyses to be made in many cases, e.g., analysis of refined lead by purely chemical means takes about two days whereas spectographically the analysis can be completed in approximately one and a half hours. The accuracy ofinstrumental methods, generally between 1 and 5%, is higher than most chemical methods for small percentages of impurities. Furthermore, if the instrument can be calibrated against absolute standards the errors are usually random and not biased to one side of the correct result. The sensitivity is high, enabling in many cases the detection and determination of smaller percentages than can be detected chemically. This high sensitivity enables and, in some cases, requires the use of very small samples, and results in considerable savings in reagents, allowing the analysis of considerably more samples without undue loss...

Jan 1, 1951

An automatic control system of a longwall roof support is dis-cussed. Hydraulic automatic control systems for longwall roof support have not met all requirements for such systems. Utilization of standard hydraulic elements to form a system that would-comply with all demands leads to a very complicated structure with a large number of hydraulic hoses within and between adjacent supports. So, only simplified systems have been made. This paper describes the multifunctional valve that per-mits realization of any desired logic functions, while maintaining a com-pact form, and analyses its application as a fully hydraulic automatic control system of a roof support.

Jan 1, 1985

By R J. Everett

The mining industry is beginning to adopt quality systems based on the requirements of International Standards for quality assurance, such as the ISO 9000 series. Indications from similar industries are that considerable benefits are to be had from their adoption. This paper describes the use of the International Standard ISO 9001 for quality assurance within BUKA Minerals Limited. This provided guidance for the development of a clear statement providing agreement on the processes to be followed and the outputs required when dealing with outside service providers. Discussion focuses on the interaction with BUKAÆs consultants and contractors during the specification stage, resulting from the application of quality assurance techniques. Risk analysis was used to identify and manage the risks associated with the companyÆs contract for geotechnical and mine design services and the tender for a mine development program of work during the feasibility stage of the project. Setting acceptance controls for the deliverables from such contracts is traditionally fraught with difficulty. BUKA used Failure Mode and Effect Analysis for exposing underlying risks that were not effectively being countered. The briefs were reviewed and additional controls were developed to manage the risk. These controls have provided clearer instructions to the consultants and contractors, indicated audit points for the company and defined the deliverables. There exists within the company, and among its outside service providers, a clearer understanding of what is to be achieved and how it will be measured. The process has imparted considerable confidence to both parties on how the work will proceed and what outputs are to be provided. Some discussion is provided on how quality principles are being applied throughout industry and commerce, generally, and how they may apply to the mining industry. The paper argues that, far from being an appendix to the tendering process, Risk Management should be a mandatory step integrated into the definitions of the work.

Jan 1, 1998

By S H. Sie, R Seetharam, K Naito, T Takagi

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medicallhigh-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnS2), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

By Mahoney M

For gas content analysis in recent years, it has been standard procedure to report results on a 'dry ash free' (daf) basis, under the assumption that gas only adsorbs onto coaly material. In order to test the relationship between ash and sas content, samples of various rock types were taken from two drillholes in the Newcastle Coalfield. The results of this study confirmed the correlation between gas content and ash, providing an accurate means of relating gas contents for all carbonaceous rock types.

Jan 1, 1995

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016