Search Documents

MR JOHN S Foxall wrote: Mr Clayton in his paper on the above subject (Proceedings, N.S. No. 34) made an assertion which should not be allowed to remain unchallenged. On the top of page 10 appears the following statement;- "By viewing the box at adepression angle of 45°, all the dimensions are disclosed and the box may be projected on isometric co-ordinates" and lower down on the same page:- "An isometric plan, being virtually a projection on a plane inclined at 45°, the nearer the dip approaches this figure so is the outline of the stoping more truly shown." Those statements embody an inaccuracy which would be misleading were an isometric plan to be constructed to suit a special case, ie the case of a mine whose lode dipped at 45°, or approximately 45° and it would be found that in such a plan the outline of the stoping would not be truly shown. The reason for this is that the depression angle at which an object is viewed in order to...

Jan 1, 1920

Whilst much has been written in past years by geologists, scientists, mining engineers, etc., regarding the well·known and justly notorious anticlinal, or, as they are more commonly known, " saddle" reefs of Bendigo, comparatively little noticehas been given to the synclinal or "inverted saddle "reefs and their relationship with each other. In taking up the question of the synclinal folds, I recognise that it is a large undertaking to confine within the limits of a short paper, and at the same time convey a comprehensive idea of their characteristics, and the importance of their relationship with the anticlinal folds, in the general question of practical mining. However, from a practical point of view I consider the question of great importance, and if an interest in it can be awakened, more particularly among practical men, the object of this paper will be achieved.Before entering into the subject I must briefly state some facts, and perhaps some theories, in respect to the deposition of the Lower Silurian rocks, and their subsequent buckling up, as now seen on the Bendigo gold-field. At the same time, I do not intend to go very closely into the geological aspect of the question, as I wish the paper to be considered as a practical one.

Jan 1, 1902

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By H Kurth

Geoscan is used for multi-elemental analysis of conveyed bulk materials in real time. It has been used for coal analysis since the 1990s, in the cement industry, and since 2003 for measuring mineral ore quality. Geoscan-M has proven performance and demonstrated paybacks of weeks or months, in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering and dust levels. Increments of two minutes (typically one to five minutes) are accurately measured and provide the plant operators with tonnage weighted results of each element within seconds.A Geoscan installed after crushing is able to measure quality shortly after mining. The analysis results can be used to divert the increments based on composition, such as diverting waste for disposal and diverting marginal material to a stockpile for processing at a later date. The bulk sorting process allows different qualities to be placed into relevant stockpiles for subsequent blending. Material meeting product DSO (Direct Shipping Ore) quality can bypass a beneficiation circuit to prevent unnecessary treatment costs. An analyser in a blending application enables proportioning of different quality feed materials from multiple stockpiles to achieve a desired compositional consistency for process feed. The parameter used for decisions may be; a) primary metal content, e.g. Cu, Fe, P, etc. b) deleterious component content, e.g. Mg as an indicator of talc content, c) process parameter content, or a combination of these. Process parameter content may be the elemental ratio between critical components, e.g. Cu:S ratio, Fe:Si ratio, basicity, Lime Saturation Factor, etc. or the content of an “indicator” element, e.g. Si as an indicator of material hardness or grindability.Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Compositional variability can be critical in the process and advance warning enables appropriate reactions prior to processing. This may include modifying the feed rate, changing the feed blend (through additives), or modifying reagent dosing in anticipation of a change in feed quality. Benefits include, but are not limited to; reducing waste processing, improved feed grade stability, reducing energy, water and grinding media consumption, producing less tailings, increasing process efficiency, higher metal recovery, better plant utilisation, reducing plant downtime, better utilising mined material, all achieved using the same process plant throughput capacity.CITATION:Kurth, H, 2015. Optimising plant feed quality and process performance using Geoscan elemental analysis, in Proceedings MetPlant 2015, pp 373–380 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

IF a straight line should be drawn on the map (See 1, page 96) through the northern half of the South Island of New Zealand, from Mt. Domett in the north to Arthur's Pass in the south, and another line drawn parallel to it and at a distance of ten miles to the west, according to the topographic scale, it will be found that within the belt thus drawn across the country all the most important mines, past and present, of the South Island are situated, with the exception of a few in Otago.The most important product of this tract being gold, and Reefton, the most important southern mining field, being situated at about its central portion, the zone may aptly be termed "The Great Reefton Gold Belt." The occurrence of so many gold mines along this particular strip of country is not at all a matter of chance, but is the outcome of cause and effect. Running along the eastern side of the gold belt are the Brunner and Victoria Ranges, which are chiefly composed of crystalline schists and metamorphic granite of probably Cambrian or Silurian age; between these and the gold-bearing series there are interposed at one or two places some beds of slates, limestones, and...

Jan 1, 1910

By P Lindsay, J B. Hughes

Underground and opencast coal mining has been ongoing since 1896 on the Stockton Plateau, West Coast, New Zealand. Acid Rock Drainage (ARD) from historic and current mine workings has had an adverse environmental impact on the surrounding aquatic environment. The two main catchments affected by ARD are those of the Mangatini and St Patrick streams. These catchments flow into the Lower Ngakawau River, which holds high amenity value for the local community. Water quality targets set by Solid Energy for 2010 in the Ngakawau River include increased pH and clarity and a decrease in certain dissolved metals.   At-source ARD minimisation options are the first stage in mitigating the effects of mining acid forming rocks and reducing acid loads in the Mangatini and St Patrick stream catchments. ARD minimisation techniques reduce the quantity of acidity generated and thus reduces the treatment required. Treatment will be required for many years at Stockton due to current and historical acid formation. This paper looks at the treatment options that Solid Energy has been investigating including limestone leach beds, engineered wetlands, oxic limestone drains, and limestone dosing of catchment drainage. Particular focus is given to fine limestone dosing of the Mangatini stream and subsequent water quality improvements.

Jan 1, 2007

Distillation of the large and growing greenhouse literature indicates that: ò Global warming has occurred over the past century or more; ò Build-up of CO2 (and lesser greenhouse gases) in the atmosphere is a fact; ò This build-up is likely to cause further global warming. It does not appear possible to conclude that the observed C02 build up and observed global warming are linked; nor is it yet possible to forecast global or regional climate variation with conviction. The dominant greenhouse gas is C02 with about half the warming potential of those gases emitted by man's activities; and about 80% of anthropogenic C02 emissions are from the burning of fossil fuels. Fossil-fuel C02 emissions arg divided about equally between the developed countries of OECD and the rest of the world. However C02 output growth over the past decade was about 4% for OECD and some 40% elsewhere. Population growth and pressure for better living standards will ensure continued higher growth outside OECD. Uncertainty about the impact of increasing C02 emissions on climate, and the long lead-times involved in limiting the increase in atmospheric C02 concentrations, are good reasons for taking action now. Australia accounts for about 275 million tonnes a year or just over 1% of the CO2 emitted from the world's consumption of fossil fuels, and the fight to control global emissions will be won or lost elsewhere. Australia's participation will be by wise conselt and by example. In view of the uncertainties involved, it appears premature to take actions that might place an additional financial burden on our hard-pressed country. However, much can be done now that makes good economic sense and has the added benefit of limiting the growth in Australia's CO2 emissions. Natural gas emits less C02 per unit of energy when burned than either coal or oil. Furthermore, new gas-fired power stations utilise energy at considerably higher efficiency than is the case today with coal or oil. Because of much lower capital costs, there is a compelling economic case for permitting natural gas to compete freely with coal in the Australian power generation market.

Jan 1, 1989

By J Johansson

The aim of this paper is to discuss how to form work and organisations in the mines of the future. The Kiruna underground iron ore mine in the far north of Sweden is used as an example on how technical development affects organisational issues like skills, work identity and gender. Over a period of 50 years one can see a transformation of work from manual underground work to automation and remote control from surface level. What characterised the old underground workface was the close relation between man and the hard rock and with arduous physical work under dangerous conditions. Today, the face miners are located on the seventh level of an office building close to the mine. There is also an emerging, and in many aspects already evident, knowledge transformation û from the old and obsolete physical and tacit knowledge and skills (for example the ability to æread the rockÆ) to something new, which can be described as abstract æhigh-techÆ knowledge and skills. The modern technology has created a new type of work û new in terms of competencies and knowledge as well as workload and organisation. At the same time the mining company are recruiting more women and promoting the former pure male work as attractive workplaces for both women and men. All this has effects on how individuals and company create and recreate skills, identity and gender. To some extent the technological development predestines these changes, but there are some choices to be done when forming good work and organisations for the mines of the future. The traditional mining workplace culture and behaviours and the old type of masculinity, the æmachoÆ style, will be challenged by the new æhigh-techÆ work and new competency demands. The changes risk meeting restoring responses, which can have negative impact on the performance of the organisation, for example making it inflexible and perhaps ælaggingÆ behind the technological development. These questions need to be handled when planning future mining.

Jan 1, 2008

By S Graskoski

The allocation of boggers and trucks at Telfer’s sublevel cave mine is currently assigned by manual techniques, with decision-making primarily dependant on the judgement of the operators and mine control. Field observations indicate that allocation decisions could be improved by establishing a systematic approach to dispatch. An investigation into the current state of technology determined that no currently available solution would provide a tool to make optimal decisions for the Telfer dispatch challenge.In an underground sublevel cave (SLC) environment, the destination decision is fixed and the source is variable, so open pit and block cave solutions are not relevant. Newcrest underwent a development venture with an external vendor to develop a novel production dispatch algorithm and user-friendly software program to make allocation decisions in a systematic way with consideration given for the true complexity of the operation.This new production software, nicknamed Dingo (for Dispatch ‘n’ Go), is a smart way to assist forepersons and mine control operators in their day-to-day roles of planning shifts and allocating trucks and loaders to optimal locations during shifts.CITATION:S Graskoski, 2017. Dingo – an optimisation tool to solve complex short interval control at Telfer underground mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 261–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

Python Underground Processing Plant Critical Design The use of continuous gravity recovery in combination with a controlled breakage fine crushing and screening system followed by flash flotation has been incorporated into the Python processing plant. This provides miners with a flexible, robust, low cost, low energy pre-concentration process for the recovery of gold and/or heavy minerals. The Python plant incorporates fine crushing utilizing either High Pressure Grinding Rolls or Vertical Shaft Impactors in combination with the InLine Pressure Jig and Flash Flotation to continuously liberate and recover the valuable minerals. The use of these technologies has enabled a narrow, transportable pre-concentration plant to be produced which can easily be installed and operated in underground drifts and tunnels.

Sep 13, 2010

By R G. Reddy, A Yahya

The sulfur distribution ratio (Ls) is an expression of the amount of sulfur in slag to the amount of sulfur in molten metal. The sulfide capacities calculated from Reddy-Blander (RB) model were used to calculate the sulfur distribution ratio (Ls). A new Reddy model for sulfur distribution ratio (Ls) was developed for modelling Ls for ironmaking, steelmaking, and secondary steelmaking conditions. Besides calcium oxide, the major component in the ladle furnace (LF) slags is alumina. The Ls was calculated for typical LF slags as a function of temperature and composition. The model calculated Ls values are in good agreement with the experimental and industrial slags data. The extremely low oxygen potential in these furnaces after fully-killed steel is favourable for desulfurisation. For any given slag’s composition and temperature, its sulfide capacity can be calculated a priori. The equilibrium sulfur distribution ratio between this slag and liquid metal in a particular vessel can also be calculated a priori. The Ls for ladle furnace (LF) slags is about twice those for blast furnaces (BF) slags and ten times those of basic oxygen furnace (BOF) slags. The desulfurisation of pig iron in BF and desulfurisation of steel in LF during secondary steelmaking are recommended. Steel desulfurisation in steelmaking furnaces is not effective. Since the model used to calculate the sulfur distribution ratio (Ls) is a priori, it is a useful tool for the iron and steel makers in improving the product quality and optimisation of the industrial furnace operations.

Aug 21, 2024

Conventional hand drawn isopach maps of the cover of the Bulli Seam are too eomplex for use in the delineation of large domains of similar cover. Isopach maps prepared from trend surfaces fitted to the cover data are much simpler in form and so provide a convenient method of delineating broad domains of similar cover.

Jan 1, 1968

By A Kuras

Segmental tunnel linings are becoming more common in Australia. One current project employing a segmental lining is the City West Cable Tunnel (CWCT) in Sydney. The project has been commissioned by Energy Australia and is currently being constructed by Thiess Pty Ltd. The project includes 1.6 km of tunnel boring machine (TBM) driven, segmentally lined tunnel. The majority of the CWCT will be excavated through Hawkesbury Sandstone. The tunnel is required to carry a 132 kV electrical circuit under SydneyÆs central business district (CBD), between Haymarket and Energy AustraliaÆs City North Substation on Sussex Street. The segmental lining has been designed as a 3.2 m internal diameter, 200 mm thick universal ring with six trapezoidal segments. The design and detailing of this segmental lining presents some noteworthy challenges, including exposure to saline groundwater, and the exclusive use of steel fibres for flexural and tensile concrete reinforcement. This paper describes some of the key elements of the segmental lining design. These include:the case for choosing segmental linings over other forms of tunnel construction;the major design checks required of a segmental lining including ground loading, hydrostatic loading, joint bearing, joint rotation, ram loading and the early strength lifting case;the benefits of using steel fibres over conventional steel reinforcement;the design approach used for steel fibre reinforced concrete;the application of 3D computer modelling in the design;the provision for components including connector dowels and gaskets;the design for passive fire resistance; andthe design for durability of steel fibre reinforced concrete in a saline environment. Segmental lining design requires the application of specialist design approaches. Input is required by the construction team, as the methods of demoulding, handling, transportation and installation impact on the lining design. As the segmental lining is functioning as immediate ground support and also a permanent lining, high standards of manufacture and construction quality control are required to ensure that the 100-year design life is met. The requirement for a watertight tunnel means that detailing and installation of the EPDM gaskets is of importance.

Jan 1, 2008

A tectonic interpretation of the Coromandel Peninsula which suggests that the basement underwent tensional collapse at its northern and southern ends would permit more ready penetration of late stage magmatic fluids. This hypothesis is consistent with regional trends of the chloride content of low grade geothermal waters and of the yield of gold and silver per unit weight of quartz worked. The consequences of such a model are that mercury should not only be a good pathfinder for Coromandel gold, but that it should be correlative with ratios of base metals high in the zoning or paragenetic sequences to those lower in the sequences. This is demonstrated successfully in an area of mineralisation in the southern Coromandel.

Jan 1, 1987

This paper sets out to examine the possible relationships between three factors, they are, the rate of growth of world production of minerals, the growth of Australian production and the growth of scientific and engineering knowledge.The first two are quantified, in terms of tonnes and value. The third, an abstract concept "knowledge", requires to be quantified, in terms of manpower.A mathematical model, which has general application, was derived to demonstrate certain axiomatic premises and to define, more precisely, basic concepts related to the philosophy of knowledge.Finally a summary is made of education-cum-industry issues.

Jan 1, 1981

By J Missen, P Currie, J Bohan, D Clark

AGL is one of Australia’s leading integrated energy companies and the largest ASX listed owner, operator and developer of renewable energy and thermal generation in the country. AGL owns and operates the 2210 MW Loy Yang A power station and adjacent 30 Mt/a brown coalmine in the Latrobe Valley, Victoria. It also supplies coal to the nearby 1050 MW Loy Yang B power station owned by the GDF Suez (Engie)/Mitsui partnership. The mine is currently nearly 5 km long, more than 2 km wide at the operating face and up to 200 m deep. AGL employs a large workforce at Loy Yang and a substantial amount of services are performed on-site by contractors and consultants.GHD provides mine planning, earth sciences, civil/geotechnical engineering, dam surveillance, plant engineering and environmental services to AGL Loy Yang through an alliance framework. GHD is one of the world’s leading professional services companies operating in the global markets of water; energy and resources; environment; property and buildings; and transportation. In addition to GHD’s global footprint, the company also has a significant Victorian presence, including a permanent, well-resourced regional office in Traralgon, approximately 10 km from Loy Yang, as well as a permanent site office.A joint paper on the Loy Yang mine professional services alliance model was written for the AusIMM International Mine Management Conference in 2006 by Woods and Wood. Now ten years on, this paper provides an overview of the present relationship and arrangements, including the continued transformation of the alliance model and maturing of the relationship contract.These are challenging times, with increasing cost and regulatory pressure driving change in the broader energy and resources industry, and locally including both the mining and power sectors at Loy Yang. Flexible models to achieve a balance between internal personnel and access to key external skills, whilst achieving value for money and transparency, is increasingly critical. The right drivers and performance measures are essential, particularly when confronted with potential major technical and environmental risks (considering significant ground failure and fire events that have occurred elsewhere within the Latrobe Valley over the last decade) within a sector that is reducing costs and optimising production.This case study discusses the alliance status and changes, reasons behind adjustments and what the future is likely to hold. The paper also explores the validity of the original objectives and the extent to which they have been achieved. The philosophy of the alliance is to continue closely aligning the objectives of the two companies in the best interests of the Loy Yang site and immediate surrounds/stakeholders. Quality of service, costs, timeliness, health and safety (H&S) and some operational activities (aquifer depressurisation) remain important aspects and are reflected in key indicators for which performance is measured.CITATION:Clark, D, Bohan, J, Currie, P and Missen, J, 2016. AGL energy, Loy Yang and GHD – a further case study in alliancing: ten years on, in Proceedings International Mine Management Conference, pp 321-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

A broad zone of intra-plate volcanism occurs for some 3000 km along the E. Australian coastal regions, extending from far northern Queensland southwards to Tasmania, westwards to western Victoria, and into southeastern South Australia. The age range, taken over the whole region, extends from Eocene to Holocene. Wellman & McDougall (1974) recognised the occurrence of three distinct types of volcanic occurrences: (a) Lava field provinces, dominantly basaltic and commonly strongly undersaturated, but of variable size. Large lava fields are especially exemplified by the younger provinces in northern Queensland (e.g. Nulla, McBride), and western Victoria. (b) Central volcano provinces, in which a reasonably well defined volcanic edifice is discernable. Such provinces are built of mildly undersaturated to saturated mafic lavas, but are also characterised by felsic volcanism (and often substantial mafic and felsic intrusive phases). Examples are the Springsure-Minerva Hills province, the Tweed and Focal Peak Shields (southeastern Queensland to northeastern N.S.W.), and the Nandewars, Warrumbungles, and Canobolas volcanic centres (N.S.W.). (c) A single leucitite province in N.S.W. Wellman and McDougall (1974) were able to show that the central volcano provinces exhibit a remarkably regular southward age migration pattern, the calculated migration rate being 66 + 5 mm yr , and these authors interpreted this in terms of the northward passage of the Australian plate across a fixed 'hotspot' within the upper mantle. The leucitite province also fits this migration pattern. The lava field provinces apparently exhibit more erratic regional age distribution patterns, but Sutherland (1981) has interpreted the data in terms of a multiple 'hotspot' model. It is noted, however, that the youngest areas of volcanism (Pleistocene 1. Department of Geology and Mineralogy, University of Queensland, St. Lucia, Brisbane, Queensland

Jan 1, 1987

THE following short paper on the Blair Athol coal-field will no doubt have a twofold interest to members from the fact that its main seam, known as the "Big Seam" of a maximum thickness of 91 ft without a band, is unique, being probably the thickestseam of high-grade clean coal yet known, and also because of the interesting problem it presents the colliery engineer-viz., which system of mining is the best to secure the highest economical extraction.Location - Blair Athol is a mining township in Central Queensland, situated at an altitude of about 1100 ft. above sea-level at the end of a branch railway line 74, miles from Emerald, on the Main Central Western line, and 240 miles by rail from Rockhampton.Geology - The coal-measures appear to lie in a shallow basin of about four or five square miles in area, surrounded on all sides by slates and schists, which are overlaid oh three sides by alluvial deposits of up to 150 ft. in thickness, and on the fourth by a thick basalt bed, as yet unproved, some miles beyond which the auriferous slates outcrop. These alluvial deposits have been largely worked in years past and gave high gold returns, the chief diggings being Clermont and Macdonald's Flats in the south, the Springs and Black Ridge in the north-east, and Yankee Creek and others on the west. The surface of the coal-fields may be described as unbroken, but undulating, with gentle southerly dip, the watercourses opening out into wide flats. The absence of creeks or deep gullies accounts for no outcrops being visible on the surface, and the coal-measures...

Jan 1, 1918

Thermodynamic properties of the solutions of hydrogen in metals and carbon in austenite were investigated and it is possible to predict the interstitial solubility in these systems over relatively wide ranges of temperature and solute activity. Monte Carlo methods were used to compute the arrangements of interstitial atoms on the tetrahedral sites in body centred cubic metals and the octahedral sites in face centred cubic metals. It was shown that the non-configurational entropies of solution of hydrogen in metals can be interpreted as being principally vibrational and on this basis the potential value of the isotopic solubility ratio theory in indicating the compositional variation of these non-configurational entropies was discussed. The need for future work along these lines is pointed out.

Jan 1, 1970

Winzes are usually sunk 9 ft. 6 in. long by 6 ft. 0 in. wide and are divided into two compartments, 4 ft. 0 in. by 5 ft. 0 in. inside the timbers. The general practice is to sink the winze to a depth of from 9 to 12 ft., put in bearers and three or four rings of timber, and then erect a sinking headframe before continuing sinking operations.GENERALThe main feature governing the design of the headframe was that all parts could be transported on timber trolleys in No. 2 Shaft. Except for some minor details the structural members consist of steam pipe. Joints are sections of steam pipe welded to one member and into which the other member fits and is held in place by a 1-in. bolt. The headframe consists essentially of two bedpieces to carry the winch and to form a seat for the four legs. The legs support the sheave bearers, the tipping door and the brace.Except during tipping operations the door is in a nearly vertical position. For tipping it is lowered to an inclined position and a hook suspended from one of the bracing members of the headframe is attached to a "D" welded to the bottom of the kibble. This causes the kibble to tip when it is lowered on to the tipping door. The capacity of the kibble is 4 cubic feet.THE HEADFRAMEThe dimensions of the headframe are:Height to top of sheave .. .. 14 ft. 10 in.Distance centre to centre of legs 4 ft. 4 in.Length of bedpieces .. .. .. .. 8 ft. 9 in.The weight is approximately 2,000 lb., the tipping door and bedpieces being the heaviest members. They weigh 240 lb. and 170 lb. respectively.One compartment of the winze is decked over, and the bedpieces, which are 8 ft. 9 in. lengths of 6 in. pipe with three short lengths of plate welded to the underside, are placed over the sinking compartment, either transversely or parallel to the winze. Three 3 inch pipes act as spreaders between them.Welded to the top of each bedpiece is a 6-in. by iHn. plate 3 ft. 0 in. long with four 4-in. by 1.5-in. slots cut longitudinally at 10 in. centres. Two 10 in. by 4-in. timbers are bolted to these plates, the distance between them being adjusted to suit the holes in the winch bedplate, which is bolted to the 10-in. by 4-in. timbers.Two short lengths of 3 in. pipe are welded to each bedpiece at 4 ft. 4 in. centres. These form the seats for the legs of the headframe, which are...

Jan 1, 1941