Search Documents

By N J. Grigg

Gekko Systems has developed an underground pre-concentration plant (Python) to reduce mine operating costs. Many ores liberate favourably using either high pressure grinding rolls (HPGR) or vertical shaft impactors (VSI). Using these comminution circuits for mineral liberation; rather than for the final recovery process and by utilising a high mass pull, high recovery process route (gravity/flotation), a narrow, low head, compact processing plant was developed that can sensibly be operated underground. The Python underground processing plant can provide a number of advantages for narrow vein mines including lower haulage costs, improved mine call factor and lower operating costs. The focus on fine crushing reduces the power requirement of the plant to approximately 8 kWh/tonne. The Python underground processing plant has been designed to be towed down the decline or lowered down a shaft, and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a saving in mining costs and a significantly smaller environmental footprint.

Jan 1, 2008

By C Zhang, I Canbulat, S Saydam, H Yu, H Chen

Natural rocks are frequently exposed to groundwater and complex geological conditions. Environments with water presence are more susceptible to chemical corrosion, which notably affects rock’s micro properties. Generally, the pH of acid mine drainage in hard rock mines can be low to 5, and the pH of quarrying waste deposits can be below 3. With the expanding scope of mining engineering in aquifers and salty areas, chemical corrosion can also caused by different types and concentrations of anions. The anions can significantly affect rock’s mechanical properties. Therefore, it is critical to emphasise the impact of anion and acid on the mechanical and micro characteristics of rock. This paper commences with an introduction to representative corrosive environments. Then the UCS tests are conducted on granite samples corroded by chloride ions and sulfate ions. Anion has negative effects on the strength of granite. The reason is that certain minerals can react and be dissolved by anions and hydrogen ions, such as Al2O3. Furthermore, the scanning electron microscope (SEM) shows that the roughness of the fracture surface increases with the anion concentration. The effect of acid is notably more pronounced than anion on the micro properties of granite. The initiated fissures and pores also increase with the concentration of SO42- and Cl- ions, which is the micro explanation for the impact of anion on rock strength and stability. Subsequently, the permeability of the granite specimens is tested. The reason that granite performs insensitivity to acid and anion is attributed to its low permeability and high content of inactive oxides, such as quartz. To summarise, anionic and acidic conditions can slightly deteriorate the mechanical and micro properties of granite. While SO42- demonstrates a higher level of corrosiveness on granite than Cl-.

Sep 1, 2024

By B Hiebl, J Martens, L Petzold

A research team at the Iron and Steelmaking department at Primetals Technologies has established new upgrading measures for improving the efficiency of the beneficiation process in ironmaking plants, relying largely on pre-existing equipment. After the upgrade, the iron content in the final iron ore concentrate was shown to be significantly higher. Remarkably, the costs for employing the respective measures are surprisingly low.This case study is based on a Kazakh iron and steel producer, whose beneficiation process is currently generating a magnetite concentrate with a final iron content of 65.65 per cent. The study shows that the implementation of Primetals Technologies’ intelligent modification measures to the current beneficiation process, the realisation of more effective dewatering, and the utilisation of an innovative binder lead to an increased iron content in the resulting pellets, reaching a concentration of 69.17 per cent (iron ore concentrate) and 66.5 per cent (pellets).The current operation consists of three closed circuit grinding stages, four stages of low intensity magnetic separation, vacuum disc filters and straight-grate pelletising. By dividing the slurry after the second stage of grinding and the third stage of low intensity magnetic separation, it is possible to divert the more iron-rich fines before they would enter the third grinding stage and the fourth stage of magnetic separation. This then reduces the load on the existing third stage ball mill. Afterwards, the ground material is treated in an additional low intensity magnetic separator and mixed with the previously diverted fraction of the fines. An improved filtration procedure, combined with the application of a highly sophisticated binder, further reduces the amount of additives needed, so that a genuine direct reduced (DR)-grade iron concentrate is produced as a result.All laboratory, pilot and pelletising test work was executed at Primetals Technologies’ laboratories in Austria.CITATION:Martens, J, Petzold, L and Hiebl, B, 2017. Enabling iron ore concentrate for the production of direct reduced iron with pre-existing beneficiation lines, in Proceedings Iron Ore 2017, pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Life inside the mining family was regulated by the mine. The whistle shrieked the change of shift to the Cornish, Welsh and German miners digging the alien soil for copper at Burra in the 1840s and the deep quartz gold mines at Bendigo in the 1880s.During the golden years of alluvial mining in the 1850s, and later out on the frontier fields of Kalgoorlie and Jarrahdale in Western Australia, the lure of the mine dominated family life. How could it do anything else? The canvas tent, bark hut or weatherboard cottage in which the mining family lived close by the mine facilitated prompt access. The working man of the family attended to the demands of the mine first, and those of his family afterward. Who then organized and nurtured the mining family? The role of the mining wife was multi-fold. She played the traditional roles of home-maker and comforter, raising her children, tending her house and vegetable garden and supporting those friends and acquaintances who had lost children to disease, or menfolk to the mine. Epidemics of measles, the whooping cough or influenza carried away children in infancy or at too young an age. The death of a husband through accident or disease (pthisis was a likely killer) forced upon the mining wife another role, that of provider. When Elizabeth Vigus' husband died in a Bendigo mine accident in March 1880 Elizabeth set up a grocery business to support her young children.' But in other cases the mining wife supplemented the family earnings by part time work, not in the mines for the Mines Act legislation of 1842 forbade the working of women underground, but in auxilfiary occupations which were in demand.2 Ann Mitchell, a herbalist ,found plenty of work in the goldfield towns of Daylesford and Maldon in the 1860s and 1870s.3 So too did Susan Rule and her daughter Catherine who conducted a sewing and millinery establishment in Beechworth in the 1870s.4 The making of the family's clothes was another task of the mining wife and mother.Until the wonderful invention of the sewing machine, this was a tedious and time-consuming task. James Slater Edmonson bought his wife a Wertheim for the sum of 12 pounds in June 1886, just before leaving her and his chil- dren in the Adelaide suburb of Goodwood whilst he went alone to the goldfields of the West. In October of that year he wrote to Louise telling her how he missed the childrens' wondering "whether Slater wore my old shirt now. I always think of him as he sat on my knee at breakfast in that old shirt; and how pleasant it would be if I could rock both of them and sing as I used to do".5

Jan 1, 1988

By V Lawson

Vale’s Sudbury Clarabelle Mill processes Cu/Ni ores from a number of mines in the Sudbury basin in Ontario, Canada. Bulk sulphide flotation produces a copper-nickel concentrate with pyrrhotite as the major diluent. After successful commissioning of the Voisey’s Bay Cu/Ni Mill (VBN) in Labrador, a miniplant campaign on Clarabelle ore with the VBN flow sheet produced a significant recovery improvement over current performance. In 2001, the Mill Redesign Project moved grinding energy into rock/sulphide and pentlandite/pyrrhotite separation and in 2006 Cu/Ni separation was re-introduced to Clarabelle Mill to produce a saleable Cu concentrate. The projects were a great success. What remained was to simplify the Clarabelle flow sheet by introducing the missing components found in the VBN flow sheet. This project known as CORe has evolved through many stages including the mining boom and surviving the 2008 economic downturn and it is scheduled for completion in mid 2013. This paper outlines some of the challenges faced in this major brownfields project – organizational, technical, financial and operational.

Aug 8, 2011

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

Longhole stope overbreak has always been a source of unwanted cost within the underground mining industry, and efforts to control it using various rock reinforcement systems have long been a rock engineering challenge. At the Pasminco Mining Broken Hill Operations trials have been carried out using an innovative cable bolt reinforcement system known as Rib-Roc. The system, based loosely on the Swedish Rib-in-Roc concept, utilises zones or ribs of heavily reinforced rock in the troublesome hangingwall and back areas of longhole stoping. The trials were carried out under a strict qualitative and quantitative scientific stope measurement program utilising rock mechanics instrumentation. Not only did the trial demonstrate the success of the system but data obtained was useful in implementing the system virtually as standard practice throughout the operation.

Jan 1, 1995

By A J. H Newell

The background and the basis for conducting a Technical Due Diligence are discussed as well as the source information, typical studies and potential limitations. Typical short comings including ‘show-stoppers’ are presented for the metallurgical area, with examples. Issues found in other areas such as geology, mining, infrastructure and financial evaluations are briefly reviewed, highlighting the input and interaction required by metallurgists with these disciplines. A checklist is provided as a guide to maximise the success of a Due Diligence as well as a check on the quality of a Feasibility Study.CITATION:Newell, A J H, 2015. Fatal flaws in technical due diligences, in Proceedings MetPlant 2015, pp 61–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

During a mineral exploration program in an environmentally sensitive area nearMount Painter in South Australia, a helicopter was used to position, construct and service drilling rigs in order to avoid the need to create new access tracks. The drilling program was designed to optimise the advantages of natural landforms in order to minimise the environmental impact of site construction and drilling activities. This minimisation of land disturbance reduced the required amount of rehabilitation measures to the extent where all impacts of the helicopter-supported programme had disappeared within 12 months of completion of work.

Jan 1, 1995

By R J. deMelo, A, V Suckal, R A. Vilela

Massive hematite ore (MHO) is a special high-grade iron ore used as lump ore in the process of obtaining direct reduced iron (DRI). The influence of porosity on the reducibility was investigated using optical and scanning electron microscopes. Hematite is the main component of the samples and occurs as granular crystals (10 ¦m), microplates (1 ¦m) and euhedral martite (10 to 30 ¦m). Quartz, maghemite, kenomagnetite and goethite are minor components. Primary micropores (+ to 1 ¦m) are associated with microplaty crystals that fill cavities between granular hematite. Secondary micropores (+ to 5 ¦m) related to euhedral martite crystals are the most important. The total porosity of weathered samples, measured using nitrogen adsorption and mercury injection, attains values up to 18 per cent, whereas unweathered samples have a porosity less than 2.5 per cent. Varajpo et al, 2002 showed that reducibility is strongly enhanced by porosity and this work shows that reducibility can be indirectly evaluated by bulk density.

Jan 1, 2002

By Wall L, Dobos S. K, Berry-Lyons W

The air we breathe and both plant and animal matter consist largely of nitrogen, oxygen carbon and hydrogen; each of these elements has two or more isotopes, The rocks, soils and waters on which we live and from which we extract minerals and other resources are comprised of elements such as oxygen, silicon, hydrogen, sulphur, iron and magnesium; each of which has two or more isotopes. Since isotopes of an element behave identically in chemical reactions, they cannot be separated or analysed by chemical means. The different isotopes of a particular element, however, vary in mass, reflecting the variation in the number of neutrons in their nuclei, so that physical processes based on the relative atomic masses of the isotopes are used to separate and analyse them (eg, mass spectrometry). Many biologic, atmospheric and geologic processes alter the ratios of the different isotop1ees of many elements. The isotope ratios D/H and O/ O, for example, exhibit significant variations in natural waters because of isotope fractionation during evaporation and condensation. Isotope analyses of both naturally-occurring and synthetic isotopes in the near-surface and biospheric environments can be used to understand natural processes and predict the results of man's interaction with his environment.

Jan 1, 1991

Prior to the 20th century much of our infrastructure was provided by the private sector. This included toll roads, tunnels and bridges, power supply, transport and water.With the depressions of the 1890s and 1930s and the world wars, much of this infrastructure passed into public ownership. This was certainly the case in Australia as well as many other Western countries.In the last quarter of the 20th century we are seeing a swing back to private sector provision of infrastructure,-resulting'from increased needs for investment in infrastructure due to changes in

Jan 1, 1993

By K Guilfoyle, A Robertson

In the mid-1970s, trucking ore from 400 m depth to the surface was perceived to be the practical and economic limit for metalliferous underground mines. Improvements in truck design and decline development resulted in the economic depth of haul exceeding 600 m by the mid-1990s. Today, mine operators and contractors are planning to use trucks for ore haulage from depths in excess of 1000 m. The authors of this paper estimate that there are in excess of 300 diesel-powered trucks operating in mines in Australia, and that by the year 2005 more than five per cent of these trucks will be æroad trainsÆ (ie trucks towing powered trailers or truck-trailer combinations). This paper examines the road train concept, presents cost and performance data and describes the advantages and disadvantages of the road train system as well as proposing the types of applications for use of road trains in Australian metalliferous underground mines. Truck performance is based on payload and average speed (expressed as tonnes x kilometres per engine hour (t km/h)). A road train with a powered trailer has a large payload capacity and two engines to provide a high ratio of power to gross weight. Thus it is possible to exceed 300 t km/h per cycle for an average haulage gradient of 1:9 compared to 250 t km/h for conventional articulated dump trucks (ADTs). It is likely that road trains in excess of 100 t capacity will have application for level ore haulage at large mines in Australia.

Jan 1, 2002

Effects of DA as a Grinding Aid on Selective Grinding of Low-Grade Bauxite Effects of DA (a copolymer of acrylic acid and acrylamide) as a grinding aid on selective grinding of low-grade bauxite were investigated in this study. The addition of DA into the grinding system enhanced the selectivity of grinding and increased the A/S ratio in the coarse fraction of ground product, leading to improved throughput of grinding mills and alumina recovery. The results showed that DA decreased the viscosity of slurry significantly and hence improved grinding efficiency due to low viscosity at a high slurry concentration. Both the hydrogen bond formation and chemical adsorption existed between DA and the surface of bauxite particles. The adsorption of DA on the surface of bauxite could decrease stress needed for crack initiation and extending during grinding, prevent new-born crack surfaces from rejoining, and promote the expansion of the cracks.

Sep 13, 2010

By R Forster

Direct ship iron ore (DSO) operations at Extension Hill in Western Australia’s Midwest region have commenced, with fi rst product railed to the port of Geraldton in July 2011. Reserves are 14.8 million tonnes (Mt) of haematite-goethite ore overlying an Archaean BIF-hosted larger magnetite deposit which Mount Gibson Iron Limited (MGI) sold to other parties in 2006.Some unique geological aspects of the deposit shape DSO mining and processing operations. Owner-operator selective mining, blending, crushing and screening on site will produce three million tonnes per year (Mt/a) of Lump and Fines product to be trucked 86 km to Perenjori, railed 232 km to Geraldton, and loaded aboard Panamax-sized ships through the dedicated iron ore shiploader at the Geraldton Port Authority’s Berth 5 facility.The statutory approvals process for this project formally began in 2004, dominating delays in a predevelopment phase which extended over a longer period than the likely life of DSO operations. The lack of transparency, uncertainties and costs inherent in state government processes have influenced decisions made by MGI while assessing other development opportunities in Western Australia. Potential for additional Reserves exists at Extension Hill, however MGI’s ability to extend the mine life will hinge on statutory approval to explore for and evaluate other DSO resources on surrounding granted mining leases.The nature of the resource and use of existing infrastructure for product transport have enabled MGI to keep operating costs and capital intensity of this project relatively low. A tenacious development approach by MGI and robust project economics have fi nally enabled this site to take its place as a revenue earner beside the company’s other DSO operations at Tallering Peak and Koolan Island.

Jul 11, 2011

World class ore deposits can be defined commercially as deposits which contain metal concentrations in the upper quartile of resources size and/or grade, world wide, from which economic extraction can be undertaken, over a production period exceeding ten years, at a cost below the weighted average cost of cumulative production of the contained principal commodity of mines world wide.

Jan 1, 1993

Active geothermal fields show many of the characteristics seen in hydrothermal ore deposits but there are important differences as well. There are, for example, many differences in geology and chemistry between individual geothermal fields, even some nearby, and these include variations in host rock types (volcanic, sedimentary, plutonic and metamorphic), structures controlling fluid flow (normal, lateral, and, rarely, reverse faulting occur) and hydrological setting (valleys to elevated terrain).

Jan 1, 1986

By Y Potvin

Risk assessment in the mining industry is currently a topic of great interest with risk methodologies being increasingly applied beyond the traditional areas of finance and feasibility to analyses of risks due to various physical hazards including chemical, electrical, mechanical and geotechnical sources. The application of risk analysis and evaluation techniques to the management of personnel safety is being promoted by both industry and regulators but, particularly for geotechnical hazards, often there are inadequate databases for a meaningful quantitative calculation of risk. In Western Australia over the decade 1987 - 1997, the annual fatality rate for underground mining has averaged at approximately 1.3 in 1000 employees with rockfalls/rockbursts accounting for over half of these deaths (Prevention of Mining Fatalities Taskforce, 1997). Recent improvements have been made since this time, perhaps halving the annual fatality rate, mainly due to industry improving ground control measures and implementing various recommendations from the Prevention of Mining Fatalities Taskforce (1997). However there still remain a large number of unknowns when trying to address the complex area of geotechnical risk in mining. Risk calculations require information about the source of the hazard, the people or assets exposed to the hazard (the æelements at riskÆ) and the effects on these vulnerable elements if the hazard actually occurs (the potential consequences). To date, little information has been available on the exposure of mining personnel and equipment to underground hazards other than occupational safety studies on chemicals, heat, dust, etc. This paper concentrates on underground geotechnical risks and presents a data collection and rating system for the exposure of both the underground workforce and equipment to rockfalls and rockbursts. The methodology considers exposure times, personnel protection levels and hazard proximities to give exposure ratings for the major underground mining activities and hence rate different locations within a mine. This exposure methodology is then applied to the workforce and production/ development cycles in an actual WA underground mine, creating a snapshot map of differing levels of personnel exposure across the mine.

Jan 1, 2003

The story of the Penjom gold mine located near Kuala Lipis on the Malay Peninsular demonstrates the valuable role successful exploration companies can play in the development of the gold mining industry. Avocet Mining PLC ('Avocet') began exploration in the area on a limited budget in 1989, securing land tenure around the Penjom alluvial workings in July 1990. The lease granted, known as Block 7, formed part of a land package offered at the time by the Pahang State Government to develop the resources of the area. Until the late-1980s, the Kuala Lipis region, situated approximately 180 km north west of Kuala Lumpur, had restricted accessibility for security reasons precluding serious exploration or mining activity. The situation has changed dramatically in the 1990s, with several foreign explorers active in the Peninsular, targeting old alluvial and underground workings adjacent to the north-south trending Raub-Bentong Suture. Deeper drilling of these prospects has shown there is potential for both small- to medium-scale open pit mining and possibly underground operations, providing companies such as Avocet with an ideal mining investment opportunity.

Jan 1, 1997

Preparing for automated sample preparation has two facets; the need for better procedures as seen by the laboratory Manager and the approach to be adopted as envisaged by the equipment manufacturer. Both have many options and during the 1990s some at least of these options will be tried. As automation of sample preparation is only just beginning, can it be said that there is a real need for better procedures. What does automated sample preparation have to offer? Does it have real advantages or is it just a marketing tool to sell equipment?

Jan 1, 1976