Search Documents

By A R. Gerson

Pyrite, chalcopyrite and mixed sulfide samples, with and without quartz (5 wt per cent S), were subjected to column leaching to mimic natural weathering (cyclic wetting and drying). The pH and SO4 2- concentration of the column effluent was measured over a period of 78 weeks. The pH of the pyrite-only containing column rapidly decreased and remained under pH 4 after 12 weeks of leaching. The pH calculated assuming a 2:1 ratio of H + generation and SO4 2- release was slightly lower than that measured. However, a reduced H + to SO4 2- ratio of 1:1 is predicted if the release of aqueous Fe 2+ is assumed rather than the formation of Fe(OH)3. The pH of all columns containing only chalcopyrite or a 1:1 mole ratio of chalcopyrite and pyrite remained at or above pH 5 for the duration of the leach even though significant SO4 2- was released. One column containing the same initial surface area of pyrite and chalcopyrite but only approximately 0.10 the mole fraction of S as chalcopyrite maintained a pH of greater than five for the first 56 weeks of leaching and showed sporadic acid production thereafter. It is well established that oxidation of chalcopyrite results in a surface layer of polysulfide material. It is the formation of polysulfide that neutralises the acid produced on S oxidation through to SO4 2-. Hence where polysulfide formation occurs extensively on chalcopyrite the resulting solution pH decrease will be less than that based on SO4 2- production. The oxidation rate of sulfide minerals increases with decreasing pH and hence acid formation via sulfide oxidation to SO4 2- causes the subsequent oxidation rate to increase. The addition of calcite (CaCO3)to a pyrite column not only neutralises the acid formed but also decreases the rate of release of sulfate to solution by a factor of approximately 30. This is also the case where chalcopyrite is present mixed with pyrite. The rate of release of sulfate from the mixed sulfide mineral columns (after the initial release of the sulfate already present) was between one-fifth and one-tenth that in the absence of chalcopyrite.

Jan 1, 2003

By W Patton

Investment decisions in the mineral resources sector are made on the basis of an assessment of the economic potential for a mineral deposit. Given the supporting information for the location, scale, and quantity of the commodity of interest, miners and investors aim to make risk-informed decisions when considering further investment. The objective of resource classification is the synthesis of various types and quantities of geologic information used in resource model construction to assign confidence categories to the estimated mineral resources, which can then be used to support informed economic decisions. In this paper a risk-based classification scheme for iron ore mineral resources using conditional simulations is presented. The method involves categorisation of each block according to a confidence level, considering expected recoveries from a kriging model over mining production volumes. The realisations of the simulated model are used to assign risk-based confidence categories to zones of the ore deposit. One motivation for this work is to assess the sensitivity of the scheme to geologic uncertainties. Specifically, that which uncertainty in the layout of mineralising alterations and weathering overprints influence variabilities of associated rock properties and the likelihood of obtaining expected ore recoveries. It is shown these risks have material implications for a project’s economic potential. How the scheme can be extended to the grade control context and the value subsequent grade control activities is also quantified.

May 24, 2023

In process industries, time-dependent random fluctuations of raw material characteristics and mass flow rates in bulk material or pulp flows cannot be always prevented for different reasons, eg because of the geological situation (no uniform formation of the deposit) or/and because of technological reasons (segregation in bunkers or on stockpiles). Since a long time, there has been practical experiences that such fluctuations can have negative consequences, eg: ò fluctuations of the final products characteristics, ò higher expenditure for process control, and ò worsening of technological characteristics (recovery, sharpness of separation etc). In the literature, there can be found a lot of details as to, eg the improvement of the sharpness of separation in a jig in dependence on the raw material blending (Kubitza, 1981; Gathen, 1983) or the decreasing flotation recovery with increasing raw material characteristics fluctuations in iron and potash ore processing plants (Bubnova, 1978). Up to now, however, these consequences of random fluctuations, eg on the separation efficiency were not predictable theoretically. It could be shown by means of the general model for mechanical macroprocesses (Graichen, 1989), that the reduction of input fluctuations passing a blending facility can be calculated in this way. In this example, the steady state of the process is the wanted one, but, in general, the model is able to describe also non-steady states of the process regarded. On the other hand, the general model of mechanical macroprocesses has been used successfully for modelling separation processes, eg cross-flow and air classification (Molerus, 1969; Neesse, 1991; Senden, 1979; Tichonov, 1973). That is why it was tried to model the influence of input fluctuations on the separation efficiency, that means, the impact of non-steady states - as a consequence of random fluctuations - on a separation process. The models discussed in the literature are related nearly exclusive to the steady state of the process. The reasons for that lie in the (relative) simplicity of the models and the fact that the steady state is aimed at by means of blending processes under practical conditions - because of the advantages mentioned above. These models cited have proved to be superior to other models, since the basic general model for mechanical macropocesses makes possible the consideration of turbulence acting in the process unit and influencing the separation process essentially. This is valid also for modelling the turbulent cross flow classification, applied to mechanical classifiers and hydrocyclones, where the correspondence between the separation characteristics (cut size, separation sharpness) calculated and determined experimentally is much better than for other models.

Jan 1, 1993

By Demin SS

Slow seismotectonic movements along the in-clined deep fault zone under the compressional horizontal stresses are supposed to be the prin-cipal mechanism controlling the structure and processes in the active ocean margins. Within the scope of the plane strain problem a simple 2-D geomechanical model for the evolution of an island arc system is investigated. We consider a homogeneous elastic half-plane with a shea-ring surface crack. The key element of the model is viscous interaction between the crack sides, the viscisity varying with depth. The model dif-fers from the classical steady-state mode of subduction by nonstationary creep processes on deep faults and by possibly cyclical development of the transition zone.A numerical modeling of the stress-strain state within the island arc system through time was carried out using a semianalytical approach. The results of simulation are in good agreement with geological, geophysical, and seismological data.

Jan 1, 1990

The Honourable Neil Pickard has been in Parliament for something like sixteen years. He was Minister for Education in 1976, served as Shadow Minister in a number of portfolio areas while his party was in opposition, and since their return to power in 1988, he has been the Minister for Minerals and Energy. Ladies and gentlemen, I ask you to welcome the Minister, the Honourable Neil Pickard.

Jan 1, 1989

By Z Chang, S A. Mrozek, S Windle

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. It is important to understand skarn-porphyry transitions in order to use exposed skarns to look for associated and potentially larger porphyries. For such purposes, a good start is to understand the transition between porphyry and skarn in known deposits. In this contribution, we report the transition at Antamina, Peru, where skarns occur in and around a Miocene complex comprised of more than seven porphyritic intrusions. There are three types of skarn-porphyry relationships. The earliest intrusive phase, P1A, contains both endoskarn and porphyry-style quartz veins with secondary biotite halos. The porphyry quartz veins and endoskarns formed at the same time. Locally, the intrusion contains only endoskarn without porphyry quartz veins and is surrounded by exoskarns in carbonate wall rocks. In the third scenario, later porphyry (P2) intruding into P1A porphyry and skarns related to P1A contains abundant granular quartz veins and secondary biotite alteration but does not have significant endoskarn. The granular quartz veins also extend into earlier P1A skarns. The scarcity of endoskarn associated with P2 is related to the supply of Ca. The earliest P1A intrusion intruded into carbonates that supplied abundant Ca, therefore both endoskarns and exoskarns formed. In contrast, where the wall rocks of the later P2 intrusion are P1A or skarn related to P1A, there was little free Ca, therefore only porphyry-style quartz veins formed.CITATION:Chang, Z, Mrozek, S A, Meinert, L D and Windle, S, 2015. Skarn-porphyry transition – an example from the Antamina skarn, Peru, in Proceedings PACRIM 2015 Congress, pp 409–414 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The long-term production schedule of open pit mines that maximises the net present value (NPV) of a given project relies on the proper design of phases (pushbacks) within the ultimate pit limits. There is not a phase design algorithm applied in the mining industry today that gives yearly production schedules that are optimum.The majority of phase design algorithms currently in use by the mining industry aims at grouping the blocks that fall within the ultimate pit limits into phases such that the average value of the blocks within each phase decrease as the size of the phases increase. Current phase design methods are typically based on a pit limit optimisation algorithm, originally introduced by Lerchs and Grossmann (LG) in 1965. To obtain multiple pit shells to be used for the phase design, the LG pit limit algorithm successively applied to economic block models by changing the price of the commodity or some other factor that properly parameterises the size of the pit. These modified economic block models are developed by predetermining the destination for each block in the model based on a breakeven analysis and highest economic outcome between alternative destinations. Phase designs determined by these existing algorithms may be suboptimal if a given project utilises multiple processing facilities for metal recovery and particularly if these facilities have restrictions (constraints) that require blending of attributes in the feed. To overcome these problems in obtaining phases that optimise overall production schedules, a new algorithm is developed at the Colorado School of Mines. The algorithm determines the phases of an open pit mine by taking into account multiple process options for the blocks and period by period blending requirements. This algorithm has been implemented within a software program (the software) and is being prototyped successfully in the design of improved pushbacks at a copper mine in South America and on a gold mine in Nevada. This presentation will demonstrate the shortcomings of the traditional phase design methodologies based on comparison of results coming from the new approach versus the traditional.

Dec 6, 2010

Australians have always been great travellers but, traditionally Australian companies have been very conservative in contrast to more daring individual Australians. During the 1960s, '1970s and 1980s, the Australian companies spent much of their time exploring in Australia. It was only some of the major companies like CRA and BHP that had explored in places like Bougainville and Chile. However, during the mid-1980s some of the smaller companies started looking beyond their shore towards other opportunities in other countries. Why did they do this? Were they pushed or did they jump? And where did they go?

Jan 1, 1996

The Australian industrial relations system is in a state of constant change. We are undergoing a transformation from a compulsory arbitration and an award based system to one which is fundamentally rooted in the concepts of enterprise bargaining. This is true both at the State and Federal level. The structural changes which facilitate the movement away from the predominance of Awards to enterprise agreements has been fostered by both sides of the political spectrum and is a cornerstone of their respective industrial relations platforms.In determining what form or combination of forms of industrial instrument(s) should apply to the individual enterprise, employers must have regard to the viability and sustainability of each form in the changing industrial climate. In particular employers should have regard to the needs and agendas of their employees and unions which may purport to represent Them.

Jan 1, 1998

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

By Mercer JK

This paper gives a description of the research undertaken by an explosives manufacturer to give better technical advice to the Mineral Industry. Blasting Physics is defined as giving a systematic and coherent account of the initiation and subsequent effects of high explosives upon the surrounding medium. As a result of this work a mathematical model based on the gener- ally accepted mechanism of blasting has been developed. The mechanism and the resulting model are briefly outlined. IFrom'this model the effects of burden, spacing, blasthole diameter, rock and explosive properties upon fragmentation and heave can be calculated. Using these calculations it is then possible to see how variations in frag Imentation and heave can affect the overall production costs of a mine whether it is surface or underground. The overall costs are made up of a number of individual costs - drilling, blasting, loading, hauling and crushing. ach of these operations influences or is influenced by fragmentation and heave s these costs are inter-related, the

Jan 1, 1975

This paper examines some of the fundamental economics of mining - in particular, for optimisation studies, for production rate determination and for reserve estimates.It includes introductory discussion on the principles as to how economics drives mining investment decision-making, applicable to the optimising of pit shapes and production, or truck fleets, or any other part of the mine.The main part of this paper looks at the decision to start-up a mine and why the 'optimum' production rate to start-up a mine is not the point of lowest cost according to traditional discounted cash flow (DCF) analysis. The optimum production rate is usually substantially less than this rate. The paper recognises the difference between typical mining investments and investments in other industries that do not have the unique characteristics of mining and the problem of uncertainty resolution. It examines the marginal revenue effects, the marginal cost of capital and the value of a real option to expand pending uncertainty resolution as determinants of optimum initial production rates.The final part of this paper looks at applying these principles to renewable and non-renewable resources. It examines mine life and reserve estimates from an economic perspective.

Dec 6, 2010

During the middle of this century, exploration and mining reached a low ebb in New Zealand. Tas McKee did his utmost to rejuvenate the mining industry, using the latest technology and an understanding of the environment far ahead of his time. Today, advances in the geosciences enable sophisticated exploration to proceed to the drilling stage before any significant environmental disturbance is created. Thereafter developments are now carried out with integrated management of the environment and rehabilitation so that disturbed land can be used for other purposes once mining is finished. Thus, we now have environmental engineers and scientists taking their place as professionals in our Institute.

Jan 1, 1987

By G P. J Dijkema, M A. Reuter

From a material cycles perspective all processes are interconnected and consequently a process can never be evaluated as an isolated and independent unit. This also holds true for the evaluated co-incineration options. Environmental and sustainability issues for example, such as raw material and energy utilisation or air pollution, are a resultant of the whole system of industrial activities. It is therefore important, not to optimise a single process or industrial activity, but rather the whole system. Although engineering procedures for the design of individual industrial units are well developed, the problem of determining the best arrangement of these interconnected units is often far more difficult. Regulation that manages the arrangement of the units for waste processing is still under construction. In the evaluation of co-incineration, analogous principle from process control can be used: feedforward control. This principle includes the determination of which outlets can be used for all process outputs, hence avoidance of any æunusableÆ products or wastes possibly arising from co-incineration. To establish the extent, to which produced wastes are usable, a system overview is necessary, in addition to in-depth information on the subsystems, which produce and can consume wastes. Material cycles modelling can be used as the basis for a tool that supports the development of a suitable playing field. It should provide overview of the system and in-depth information on its subsystems. This tool then represents an attempt to bridge the gap between æholisticÆ industrial ecology and process engineering.

Jan 1, 2000

By Phillips RN

Semi-confined, trachy-andesite sills which overlie the German Creek Seam, within the critical tensile strain zone, form major groundwater hazards to longwall mining at the German Creek underground mines. The water contained in these aquifers is normally neutral, but highly saline. Techniques used to detect aquifers include routine air-lift pumping in exploratory drill holes, downhole geophysical and geological logging and upstage packer testing. Hydraulic constants are calculated from pump-out and pump-in test results. Hydraulic parameters for the calculation of mine inflow rates are determined from pump-out test results because these tests appear to be more representative of aquifer drainage during goat dewatering than pump- in testing. During mining of the first longwall block at Central Colliery, caving fractures intersected overlying aquifers after the longwall had retreated 40m, and mine water inflow rate rapidly increased from less than one litre/sec to 25 litres/sec. The amount of water pumped out of the mine during first panel extraction was 140 megalitres with drawdown occurring over an area of 168 hectares. In the Southern Colliery area approximately 324 megalitres of highly saline water which is actively stored in the Aquila Sill area will be pre-drained from six well points prior to longwall mining. With effective pre-drainage from surface drill holes, maximum inflow rate into the mine during initial goafing can be reduced from 165 litres/sec to about 45 litres/sec.

Jan 1, 1988

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

By M Watts, P Lindsay

Herbert Stream, a tributary of the Waimangaroa River on the Stockton Plateau, has elevated metal concentrations and low pH characteristic of acid mine drainage (AMD). Dissolved aluminium concentrations average 8.3 ppm, iron 1.4 ppm, manganese 0.69 ppm, and zinc 0.12 ppm and pH ranges from 2.8 to 3.2. Flow rates range from 2.3 to 26.6 L/s with an average of 5.3 L/s. To determine the effectiveness of different treatment strategies, a small amount of the AMD was diverted through three small-scale passive AMD remediation systems over an eight month period. These included a reducing and alkalinity producing system (RAPS), a limestone leaching bed (LLB), and an open limestone channel (OLC). Both the RAPS and the LLB performed well, effectively removing metals and restoring pH. The RAPS lowered aluminium concentrations by up to 99%, iron 97%, manganese 95%, and zinc 80% and the LLB lowered aluminium concentrations by up to 99%, iron 99%, manganese 92%, and zinc 91%. The pH was restored to between 6.4 and 7.4 by the RAPS and to between 7.3 and 7.9 by the LLB. The OLC performed well as long as the residence time was similar to that of the other treatment systems. OLC removal rates for aluminium was up to 99%, iron 94%, and manganese 21%, and the pH was restored up to 5.6. Due to its simplicity and effectiveness, it is proposed the LLB be constructed to fullscale size to treat the entire Herbert Stream.

Jan 1, 2007

By C J. Noack, P B. Ganza

The concept of large trucks underground has been around for some time. While the road train concept is gaining momentum, there are underground mining applications where these trucks have not been suitable. Unfortunately few of the ægreenfieldsÆ projects that are most suited to the road train concept have come æon lineÆ since the underground road train was first introduced to Australia in 2001 so that the trucks have generally been adapted to existing operations. As at December 2004, there were 17 road trains operating underground in Australia, one being rebuilt and one under construction. This paper addresses the necessity for the mining industry to have an integrated ore transport system that starts at the underground load haul dump unit (LHD) in the stope production area and finishes at the crusher feed at the processing plant. Chute and orepass designs are investigated, as well as feeders to determine the best load and haul system for large-scale trucking. The paper also discusses potential developments in the large truck scene. The paper highlights the cost and productivity gains by introducing large trucks and associated integrated ore transport systems underground. While 400 vertical metres was seen as the limit of vertical hauling in the 1970s, one kilometre is a common discussion point for trucking limits today. In real terms the cost of underground trucking (including ownership costs) has decreased from $1.50 - $2.00/t.km in the mid-1990s to $1.00 - $1.20/t.km at present.

Jan 1, 2005

By N F. Glenn, S Thiruchittampalam, B P. Banerjee, S Raval

The determination of shear strength parameters for the spoil material plays a crucial role in the assessment of a dump’s stability; nevertheless, their evaluation necessitates laborious laboratory experiments. In order to address this issue, Simmons and McManus (2004) formulated a framework that serves as a foundation for categorising spoils according to their distinctive shear strength parameters based on observable and tactile characteristics. This framework, previously identified as the ‘BHP Mitsubishi Alliance Coal (BMAC) Spoil Shear Strength Framework’, is now recognised as the ‘CoalSpoil’ framework. The spoil characterisation provided by the CoalSpoil framework offers benefits but is not without limitations. The examination of these attributes in the field is a time-consuming task that demands expertise. Subjectivity arises in the spoil characterisation when attributes straddle the line between two categories, such as delineating matrix-supported and framework-supported fabric structures. To enhance consistency in the spoil characterisation process, minimising human intervention is crucial to mitigate bias, classification errors, and safety risks. This study seeks to achieve this aim by introducing image-assisted and automated methods for spoil characterisation.

Sep 1, 2024