Search Documents

Methods of measuring the frictional properties of rock surfaces, both by direct sliding and in triaxial apparatus, are described. It was found that for some rocks the coefficient of friction remains reasonably constant as sliding is continued but for others it increases considerably.The effect of fluid pressure in the surface of sliding was found in all cases to be adequately represented by the effective stress criterion. Some observations on sliding on two conjugate planes showed that the motion on the two planes may be very different, depending on small differences in the constraints.The coefficients of friction of natural open joints in bore core were found to lie in the comparatively narrow range 0.32 to O.68 although surface coatings were very diverse.A set of diagrams on the equal area projection is given which enables a rapid determination to be made of those planes on which sliding is possible in a given three-dimensional stress field. The influence of the intermediate principal stress on this is of considerable importance.

Jan 1, 1969

By O Pasca, B Hogg

Consistent slag blow end point detection remains one of the challenges in the Peirce-Smith converters at Mount Isa MinesÆ Copper Smelter. Under blowing results in foaming on copper blow and carry forward of oxide skims to the anode furnace. Over blowing results in high copper losses to the slag. Both present safety issues and contribute to lower copper production. The end points of the slag making phases are assessed by inspection of a bar sample. A bar sample is a thin accretion layer that adheres to a steel bar when it is inserted into the tuyere while the converter is blowing. This method is biased and subjective, so there is heavy reliance on operator experience. The Semtech Optical Process Control (OPC) system was installed in early 2002 for converter slag blow end point detection. Initial plant trials did not improve all aspects of converter operations, and uptake by operators was poor, so the system was not used. In early 2005, the Semtech OPC system was re-visited and another short trial was conducted to evaluate the permanent use of the system for slag and copper blow end point detection. During this trial, the Semtech OPC method was found to be superior to bar sampling for slag blow end point detection. The implementation and refurbishment of the Semtech OPC system has resulted in plant improvements and given a better insight into converter operation during blowing. Oxide skim generation carried forward to the anode furnace has been shown to decrease with increasing compliance with Semtech OPC. Some of the expected improvements to converter operation were not found to be significant. Semtech OPC is now well received and utilised by converter operators. Individual paper available only. Not included in book or CD ROM Proceedings.

Jan 1, 2005

By Townsend MG, Evans RB

In Northland, New Zealand, localised large deposits of halloysite clay have been produced by in-situ alteration of rhyolite volcanics of Pliocene or Pleistocene age, which were erupted through pre- Pliocene sedimentary strata and locally through Pleistocene basalt; and which were subsequently onlapped by further basalt flows. Alteration to clay has been a result of both hydrothermal and of meteoric processes, and decreases in intensity of alteration with increasing depth.The raw material is crushed and fractionated to produce a product of less than 2 micron particle size, which is of exceptional whiteness and brightness. The unique properties of the clays render them highly desirable for specialised ceramic purposes.

Jan 1, 1990

By Komosa T, Muir D. M

Adequate levels of dissolved oxygen are essential for efficient gold dissolu- tion. The actual levels in plantpuips can be seriously reduced by the presence of oxygen consuming reactive minerals, and reduced oxygen solubility in saline water. The rate of gold dissolution is then limited by oxygen availability rather than cyanide. Ion selective electrode dissolved oxygen meters can give an effective indication of the relative oxygen saturation, but they are not able to give meaningful values of dissolved oxygen in saline water, without custom calibration curves. When the dissolved oxygen concentration is rate limiting, the addition of oxygen or peroxide can improve gold leaching kinetics as well as reduce cyanide consumption.

Jan 1, 1991

By Blackham M

West Wallsend No. 2 Colliery is a new mine that is presently being developed in the New- castle Coalfield by J. & A. Brown & Abermain Seaham Collieries Ltd., a subsidiary of Coal & Allied Industries Ltd. It is situated near Barnsley and is some 15 miles by rail from the port of Newcastle. The mine will produce coal from both Bore- hole and Young Wallsend seams. The Borehole seam has a working seam thickness varying from 7 ft to 5 ft while the Young Wallsend seam presents a choice of two distinct working thick- nesses, i.e. 5 ft. or 8 ft, the upper 3 ft containing much high ash material. The inter- seam interval varies from 10 ft on the western edge of the area to more than 70 ft in the central portion. The Borehole seam lies at a depth varying from 550 ft to 750 ft and the overlying surface terrain is gently undulating bushland with limited surface development.

Jan 1, 1972

Gold occurs at Mt. Charlotte associated with a stockwork of pyritised quartz veins in Unit 8 of the Golden Mile Dolerite. The ore- body is massive, 200m long and 40m wide and has been proved to over 600m below surface. Mining is by sublevel ring drill stoping with the ore recovered by diesel powered equipment. Ore reserves are based on traverses of diamond drill holes oriented to produce an equal intersection width on the two principal sets of quartz veins. Assay and geological boundaries are marked on each drill section and this boundary is transferred to mine plans and cross sections. Ring-drilling patterns are based on the cross sections and the resulting mining outline is transferred back to the drilling sections. The mine ore reserve is calculated from the mining outline.

Jan 1, 1979

While convergence of plates at a subduction zone produces shortening at the toe of the overriding plate, this deformation is localized to the frontal 100 km or so of the plate. There is increasing evidence that the state of strain in back-arcs, volcanic arcs, and possibly the entire forearc is extensional. The most likely cause of this extension is rollback of the subducting plate and trenchward advance of the overriding plate. Arcs are thermally weakened, and are activated repeatedly through time. The primary expression of the extensional state of strain is spreading of the weak arc material, either by splitting the arc or by back-arc spreading behind it. This study presents evidence for extension of volcanic arcs from an analysis of the moment tensors of shallow earthquakes (

Jan 1, 1990

Marketing of mineral products has not yet succumbed to the degree of pre- dictability and exactitude that is fam- iliar to the engineer or metallurgist in pursuing their profession. Whilst the Great Market of the world economy dic- tates circumstances for the sale of min- eral products, there are more than just buyers and sellers in the determination of the revenue received by the producer. For the engineer or metallurgist he will be required to gain an understanding of these participants and of the peculiar languages of the market place. This will be only one of his tasks in learn- ing to communicate with society, as his responsibilities increase as he climbs the ladder of success. There is un- doubtedly a need for better statistical information so that producers and sell- ers can make an appropriate and earlier response to market conditions. There is in addition, a need for more aggressive concern by raw material producers for the development and promotion of better end use of their products. Undoubtedly the marketing of mineral products will be more influenced by the direct involv- ment of government agencies than has been the case in the past. Whilst that 1. Director - Marketing & Finance, North Broken Hill Limited.

Jan 1, 1975

In line with mining operations throughout Australia, Western Mining Corporation Limiter' is striving to increase productivity by intro-ducing mechanized mining techniques wherever possible. Kambalda Nickel Operations' (K.N.O.) largest operating nickel mine, Long Shaft, is currently introducing mechanized cut and fill methods which must provide flexibility to cater for an orebody that variesconsiderably in width, both along the strike and up dip.This has resulted in modifications to the previous approach to primary level develop-ment, and intermediate stope development, and in the type of development and production equipment being employed. Electric-hydraulic diesel jumbos and diesel loaders have now been mated with conventional rail equipment and production airtrack machines are being utilized.The transition to mechanized methods is in its preliminary phase and is being monitored closely to ensure any productivity gains are not offset by a substantial drop in mine grade. The precise method ofmechanized mining has not been finalized and selective methods will be used, according to the ore width and ground conditions, which vary throughout the mine.

Jan 1, 1985

By Baafi EY, Appiah HK

The Prestea Goldfields Ltd of Ghana, West Africa has produced over 170 t of gold with average grade of 11 g/t since 1912. The deposits occur in a wide shear zone which closely follow the Birimian-Tarkwaian contact. Both the Birimian and Tarkwaian systems are of Precambrian age. Underground exploration is carried out to delineate ore bodies by means of AX size diamond drilling at 50 m sampling intervals. After the orebody has been delineated, development work is carried out by exposing the gold reef. Channel sampling is then carried out at about 3 m intervals in both the stope and stope drives. A channel sample length is commonly 0.6 in, but may vary depending on physical characteristics of the reef. The values of channel samples are linearly combined to obtain the average reef or slope values and/or widths of the exposed sections. The sampling practice and methods of improving the efficacy of sampling at the mine are described.

Jan 1, 1976

By Johnston R. F

The factors which influence the reduction of chromite are investigated with special reference to Coobina chromite. This was compared with a South African chromite ore. The reduction characteristics are outlined and the reduction kinetics studied Temperature has the most significant effect, followed by particle size, silica addition and type of coal.Electron microprobe analysis of the products indicates that iron in the chromite is first reduced at temperatures above 1100°C, followed by chromium at around 1200°C. At temperatures greater than 1200°C metallic iron and chromium are formed simultaneously and subsequently give an iron-chromium-carbon alloy. It was observed that the metallic carbide contains a small amount of silicon. The decomposition of the chromite spinel was observed to pass through the FeO.Cr2O3, MgO.Cr2O3 and MgO.AI2O3 forms before slag formation. It is concluded that Coobina chromite is suitable for the production of ferrochrome if direct prereduction followed by intensive bath smelting is used.

Jan 1, 1994

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

Conventional treatment of oxide and oxidised sulphide minerals by flotation involves the use of sodium sulphide for sulphidisation. Sodium sulphide is generally applied in a "slug" dosing fashion with manual regulation. However, it is recognised that "over addition" or "under addition" of sulphidising reagent can result in poor flotation recoveries. Thus, control of sodium sulphide additions is an important aspect of a sulphidisation circuit, both commercially and metallurgically. In any plant where the flotation feed is "constant" it is possible to operate at a constant rate of addition of sodium sulphide. In actual plant practice, however, it is difficult to maintain a truly constant feed for any reasonable duration because this implies not only a constant feed-rate, but also constant mineral composition and particle size range. These factors can vary significantly and ideally require corresponding variations in the additions of sodium sulphide to maintain optimum recoveries. To cope with variations in the feed, it is essential to have automatic rather than manual regulation of the sulphide reagent addition. The CPS process achieves this control by utilising a sulphide ion-selective electrode as a control instrument in sulphidisation. The CPS process which uses a selective electrode, enables the sulphide ion concentration in the flotation pulp to be monitored and controlled continuously throughout the stage of sulphidisation.

Jan 1, 1989

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Yucheng H, Baogui Y, Wenyong L

High-water rapid-solidifying material, called 'high-water material', is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of hackfill body. environmental contamination and so on, have been solved.

Jan 1, 1998

Computer-based block modelling of orebodies is now used at Renison Tin mine for the estimation of ore reserves. It is considered that this has resulted in improved reserve estimation for complex 'stratafault' orebodies. The results for all orebody types are more easily understood by the mine planning section and provide greater scheduling capability than those from the previous manual isoline reserve estimation method. A structural overview of the deposit can be gained by combining geological block models for the various orebodies. It is anticipated that upon completion of block modelling for all the orebodies the time spent on the annual ore reserve estimate will be significantly reduced.

Jan 1, 1990

By Li G, Dean-Jones G. L, She T

Highwall mining is a specialised and largely automated mining method developed in the United States for the extraction of coal left under a shallow overburden cover after cessation of economical open cut mining operations. As the name indicates, coal is extracted from the seam exposed along a highwall by a remotely controlled continuous miner operating in a single unsupported opening and brought to the surface by a string of conveyor segments. The single entries are separated by coal .pillars and driven normal to the highwall, over areas where the thickness of cover and volume of recoverable coal is insufficient to allow or justify conventional underground mining. An additional highwall mining method is augering. The success of high wall mining operations depends significantly on geological features, notably the stability of the working roof, determined by the type and mechanical properties of the immediate roof strata. Stability of the ribs, absence of floor heave, faults and dykes are further important prerequisites for profitable highwall mining. The geometric relationship between the spatial attitudes of existing joint systems, the direction (azimuth) of the single entry opening and its vertical profile determine the unimpeded depth of penetration into the coal and thus its economic success. The mechanical implications of the lithological transition zone from a coal seam to either primary or original roof strata, compared to an interface between the coal seam and overlying strata, characterised by a sharp erosional boundary between coal and a secondary immediate roof stratum, are very significant. The compatibility between the response to mining by the geological system (floor-seam-roof) and the capability of the mining equipment to prevent the development of instability are essential requirements from a mechanical viewpoint. The minimisation of vibrations, very good horizon control, an ability to vary the profile of the opening, and the maintenance of consistently high advance and retreat rates, are also important aspects of profitable highwall mining.

Jan 1, 1995

By Hulton SJ, MacKenzie DH

The Broken Hill orebody within the leases of ZC Mines is still a major lead-silver-zinc resource after over 80 years of mining. It illustrates particular problems encountered in resource and reserve estimation in old mines. The six mined ore lenses are characterised by three features: ò complex external geometry, ò high internal grade variability, ò bimodal grade distribution. The high grade 3, 2 and 1 lenses and B lode have sharp external contacts but contain some low grade internal zones. By contrast A lode is of lower average grade and comprises an extensive but geometrically variable mineralised zone within which are numerous irregular bodies of high and medium grade ore. Geological factors are the main source of variability in reserve estimation, which historically has been conservative. For many years the geological resource tonnage has been maintained at a level sufficient to make up for extraction but at a gradually declining grade. Using a geological block cut off grade of 10% Pb + Zn the present in situ resource is 53.8 Mt grading 8% lead and 13% zinc. Using empirical cut factors a "recoverable reserve" is derived from this large geological tonnage. There is some doubt that the "recoverable reserve" is conservative enough to reflect mining reality. The most sensitive indicator of forthcoming change in total resource or insufficient drilling and development is given by changes in the tonnage and grade of possible ore from which the proved and probable categories are derived. Examples are given to show that where reserves are drill indicated, the delineation required for proved ore reserves must be enhanced to achieve final stope design. The move in recent years to greater emphasis on non entry mining and lower recovery of in situ material poses a dilemma for a mine which has practised 100% recovery for much of its past. The need for a realistic reserve assessment in current terms needs to be balanced against the fullest possible geological knowledge of the resource to cater for future technological developments.

Jan 1, 1987

By A Scott

Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data û especially with semi-automated data acquisition by instrumented mine equipment. However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model. An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc not only have many areas of interest but also have very different conceptual models by which they evaluate performance. It is too ambitious to attempt to bring all of these cultures together û in a single step. However, the success of the Mine to MillTM project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from orebody model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling. However, in both cases the data collected is strongly focused on the technical requirements û not on the business model. This paper considers how to define at least some of the key decision points in terms of some case studies. Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning.

Jan 1, 2002

Gunpowder Copper Limited processes 1,000 tonne/day of Mammoth ore in a conventional flot- ation concentrator. Run of mine ore is prepared for flotation by three stages of crushing and two stages of ball milling. The concentrate, in which the primary copper mineral is chalcocite, is solar dried and exported to Japan. The history of operation is summarised, and plant practice and metallurgical problems are discussed.

Jan 1, 1974