Search Documents

By Parr JM, Scott SD, Herzig PM, Gemmell JB

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

By Enichlmayr E

Lignin grouts are cheap and easy to get. They have some desirable properties, but they aag less used now because environmental pollution is often caused by Cr from the lignochrome component of the grout. Their usefulness was researched in an earlier paper on lignin as a grout from other viewpoints. A non-toxic grout FUL was made composed of furfural, urea and lignin. After initial tests, including tests by spinning regression design, some response equations in which FUL's properties are described were obtained. Optimum formulations have been established by using optimization methods based on response equations. The engineering quality was assured by formulations whose properties were measured in further tests. The mechanical feature of gelling sand was measured by means of triaxial tests. This provides a basis for using FUL grout in-situ. Finally, an in-situ experiment on FUL was completed successfully. The results were that cracks in stratum were filled or blocked, the gelling of FUL had high strength, and low permeability and consolidation were achieved.

Jan 1, 1988

An understanding of the way that solutes are transported in mining or natural environments is essential to the development of sound strategies for managing waste disposal. Research on miscible pollutant movement in unsaturated porous media is carried out both experimentally and numerically. Results of numerical modelling are obtained by solving the groundwater flow equation and the solute transport equation. The finite element method is employed and comparisons between simulation results and experimental data are found in remarkable agreement.

Jan 1, 1995

The Matakan Unit of New Ireland, Papua New Guinea is a highly fossiliferous lagoonal deposit containing numerous coal pods and lenses. The unit is strati graphically part of the massive reefal Lelet Limestone of Miocence age. These organic-rich sediments have a high hydrocarbon potential as evident from microscopical observations as well as Rock- Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbo as Rock-Eval pyrolysis data. The coal is varied in regard to dominant macerals, vitrinite being predominant in some parts and pollen and spores present in sufficient proportions to constitute a cannel coal elsewhere. The highly fossiliferous carbonaceous sedimentary rocks associated with the coal are rich in pyrite expressed in the sulphur content (19.7 - 22.8%). A high primary productivity and anoxic sediment pore waters or just above sediment - water interface have given rise to sufficient organic matter accumulations to yield a potential hydrocarbon source rock. Atomic H/C ratios of the coals are between kerogen type III and type II mainly, expressing the mixed nature of the coal and that of the associated sediments is type II. Early generated hydrocarbons (exsudatinite) have formed from pollen exines filling the pollen cavities and in places filling micro- fissures in the surrounding vitrinite.

Jan 1, 1987

Christmas Island "C"-grade phosphate consists essentially of the minerals crandallite and millisite. Although containing over 25% P205, this material is not suitable for the manufacture of water-soluble phosphate fertilizers by conventional processes, because of its high iron and aluminium content Cover 25% total R203). In order to produce a water-soluble fertilizer from such material it is necessary to separate the iron and aluminium from the phosphate, which must report in a product acceptable as a fertilizer. Several processes were studied in detail. The first used ion exchange for dissolution and separation and yielded diammonium phosphate; processing costs were high compared with conven- tional processes based on apatite. The latter processes have basically simple flowsheets and cost of processing is low when compared with the costs of the raw materials. The need to separate iron and aluminium from the phosphate introduces additional complexity into the treatment of the C-grade material. The higher processing costs might be justified, however, if alumina could be produced as a byproduct. Two proposed processes have been developed in which: 1. hydrochloric acid is used for dissolution, and solvent extrac- tion for the separation of ferric chloride from phosphoric acid. Aluminium chloride is precipitated and hydrolysed to recover alumina and hydrochloric acid. 2. sulphuric acid is used for dissolution and aluminium is crystallized as ammonium alum. The phosphate is produced as an ammonium phosphate-sulphate fertilizer. High purity alumina can be obtained by treatment of the recrystallized alum. The technology of these processes is described, and their broad economics discussed briefly.\

Jan 1, 1971

By M Simpson, K Brodie, J L. Mauk

Subaqueous water-rock reactions that occur at the pit wall/lake water interface can affect the pH of pit lakes. Many pit lake water chemistry models neglect subaqueous reactions, which may create inaccurate predictions over time. A mineral quantification method is presented that defines the wall rock mineralogy of active open pit mines, using samples collected from the Martha Mine, a low-sulfidation epithermal Au-Ag deposit in Waihi, New Zealand. The mineral quantification method has five components: field observations and sampling, X-ray diffraction analyses, selection of representative samples, geochemical analyses, and mineral accounting. Predicted mineral concentrations closely match observed mineral concentrations visually estimated using petrographic techniques. Results of the method can be incorporated into a geochemical model of long-range pit lake water quality resulting from subaqueous water-rock reactions.

Jan 1, 2003

By Sennitt C. M, Hartley J. S

The Twin Hills Gold Deposit is an example of a preserved, high level, epithermal system, with mineralisation introduced contemporaneous with deposition. The deposit is hosted within sediments of the Late Devonian to Early Carboniferous Saint Anns Formation, of Cycle 1 Drummond Basin stratigraphy, situated in central Queensland. Prior to epithermal activity in the Twin Hills region, a lacustrine fan delta depositional environment existed, together with minor tuffaceous activity. An and palaeo climate, with occasional periods of torrential rainfall, together with a basin with faulted margins, allowed alluvial fan prograda- tion. Cyclical repetitions of the fan indicate repeated faulting and seismic activity took place during deposition. Significant gold mineralisation was first intersected at Twin Hills by Metana Minerals NL in 1988, after drill testing a "blind" target outlined by geological mapping and bedrock geochemistry.

Jan 1, 1991

Some important mineral fields are referred to in discussing the formation of placer deposits in Australia. Testing methods include boring hand, with percussion rigs; with auger and pit digging drills; and l by vibro drilling. Sampling errors are minimized by the use of correct techniques and equipment for boring, sampling, and sample dressing, A hypothetical set of data is used to demonstrate the final process of evaluation, and some relevant taxation provisions are discussed.

Jan 1, 1964

By A I. M Ritchie, G P. Timms

Monitoring of water infiltration into WhiteÆs waste rock dump at the Rum Jungle mine site in the Northern Territory, Australia, started in 1983, and has since produced a unique and long-running data set. Following closure of the uranium mining operations at the site, a soil cover was constructed on the dump in 1984 primarily to reduce water infiltration into, and the quantity of low quality effluent out of, the waste material. The performance of the cover in reducing water infiltration has been monitored using ten lysimeters installed across the dump prior to construction of the cover. Over the past eight years or so, the average infiltration rate as measured by the ten lysimeters appears to have risen compared to the early years of monitoring. The significance of this apparent increase is discussed given the variability observed in the data from individual lysimeters, and the variability in the rainfall. Estimates of the infiltration rate as measured by each of the lysimeters are examined using statistical tools. It is concluded that the infiltration rate has increased with time and with increasing rainfall. The increase with time is a stronger factor than the increase with rainfall. It is further surmised that the cover system at the locations of the lysimeters is less effective now at reducing infiltration into the dump than it was when newly installed.

Jan 1, 2003

By Duncan GR

Having passed through a number of previous phases the best longwall results in Australia have shown a significant increase in the last two years. The results expected from a longwall face can be estimated from the ideal production rate, determined by the capacity of the equipment and the conditions in which it is installed, the utilisation, and the available operating hours. Back analysis of the results achieved suggests that, on average, recent improvements arise from the higher capacity equipment recently installed; the utilisation has in fact reduced slightly. Review of the constraints which limit the longwall results, i.e. shearer speed, AFC capacity, support, advance rate, and man travel speed, shows that little improvement can be expected in the ideal production rate in thinner seams. In thicker seams the AFC often proves the overriding constraint and further increase in equipment size could lead to increased future ideal production rates and is expected. In all cases a concerted effort to increase the utilisation achieved is likely. For deep mines with thin to medium seams this offers the most viable path to improvement; by contrast thick seams with highwall/shallow access may benefit from further increase in equipment size.

Jan 1, 1988

By Georgi H, Farquhar J. W, Lorrigan A. N

The potential for major new lenses of Volcanic Hosted Massive Sulphide (VHMS) beneath the existing Rosebery Deposit is extremely high. Recent deep drill hole intersections of massive sulphides, including 22 in true thickness at 24 per cent Zn, may significantly extend the life of the Rosebery Mine. The Rosebery Ore Deposit is located within Australia's most prospective VHMS mining district, the Mount Read Volcanic (MRV) arc of western Tasmania (Figure 1). The MRVs are a 10 - 15 krn wide arcuate belt of lavas, related intrusives and volcaniclastics. Rosebery is a major Cambrian volcanic hosted Zn-Pb-Cu-Ag-Au rich deposit which has been over-printed by Devonian deformation and granitoid alteration resulting in local rcmobilisation of the ore. The Rosebery Mine Sequence is composed of an east dipping and east facing, predominately felsic sequence of rhyo-dacitic volcaniclastics, epiclastics, sediments and shale lenses more than 500 in thick. This sequence is bounded by two, low angle (35 - 40¦), east dipping thrust faults, the Rosebery Fault to the west and the Mount Black Fault to the cast. The Rosebery Mine lithologies are summarised in the following table: Hangingwall (HW) Polymictic, quartz, feldspar-phyric epiclastics. Black Slates Graphitic, pyritic mudstones. Host Rocks Turbiditic mudstones and sandstones. Footwall (FW) Feldspar-phyric, pumiceous, mass-flow breccias. Cambrian, quartz-feldspar, porphyritic sills intrude this sequence at all levels. Thin, Jurassic, dolerite dykes also occur throughout the mine. Widespread quartz, sericite and chlorite alteration occurs in the FW. This alteration is manifested as quartz-augen schists beneath the orebody. The Host Rocks are pervasively altered with silica, sericite, chlorite and pyrite. Intense carbonate alteration occurs within the orebody, whereas chlorite and pyrite alteration is commonly concentrated directly beneath it. Cambrian volcanogenic alteration is over-printed by three major Devonian, granite-derived, assemblages. These are massive to quartz veined tourmaline, pyrrhotite-pyrite and magnetite-chalcopyrite. Though the Devonian granite has not been intersected in deep drill holes or in mine workings, there is good evidence that it exists within a kilometre of the deposit. The Rosebery orebody is structurally complex when compared to many other VHMS deposits. Evidence for Cambrian growth faulting has been found at the North End of the mine (B lens) where displacement of ore lenses occurs without corresponding displacement of the overlying Black Slates. A well defined cleavage exists throughout the mine, dipping at 28 to 50¦E. East dipping shear zones are also obvious in all parts of the mine workings and reverse movement is evident on many of these.

Jan 1, 1993

WHEN reading reports on reefs and lodes, one often comes across the statements "short shoot," "narrow shoot," "wide shoot," & c.From a number of reports in the writer's possession, some by members of the Geological survey, it is plain that the words "short," "narrow," "wide," "long;" &c., are used somewhat carelessly.In one official report on a certain field, for instance, the reefs are described as having "short, rich shoots"; another report on the same field states that "the reefs were characterized by narrow shoots, rich at the surface." Again, Charters Towers is described as having "wide shoots"; another writer says they are "long shoots. "The writer has read again of "short shoots which went down like pipes," and of "narrow shoots of limited extent." No doubt one can make out what is really meant, but the language is mixed. It is apparent that "narrow" is meaning the same as "short," and that the shoot has not much length in a horizontal direction. Nothing is said about the thickness or width of 'said shoot, or its depth. The "wide" shoot is evidently a "long" one; its thickness 01' width and depth is not specified. When we consider these terms, it is seen that only a few words are needed, and that these few should (as they do) have a definite meaning. In the course of his mining experience, the writer has seen shoots of almost all sizes, and some have been very long (in horizontal measurement), and have been followed down for great depths, these shoots being the best type-Charters Towers, Walhalla, &c., are examples.

Jan 1, 1909

By Grobler H. P, Chitombo G. R

Production blasting of Dc Beers Consolidated Mines Limited, Koffiefontein and Finsch Mines involves both uphole trough rings of 9 to I I holes and near vertical 360 degree compound rings of 42-54 holes. The rate of production from these stages is dependent upon being able to achieve a specified fragmentation size range and this has driven the derivation of blasting practices to consistently achieve this target fragmentation. At the Dutoitspan Mine, in Kimberley, where mining of the kimberlite pipe is by block caving, 100 per cent extraction of the undercut level by ring blasting is essential. If this is not achieved, pillars are formed which not only inhibit the efficient initiation of the caving process, but also concentrates load onto the extraction level, causing damage to draw points and pillars. These two case studies demonstrate the importance of achieving optimum blasting performance for downstream mining efficiency; ie fragmentation for increased productivity at Koffiefontein Mine and 100 per cent undercut extraction for efficient initiation of the caving process at the Dutoitspan Mine. The case studies also serve to highlight the long road towards blast optimisation taken by De Beers Consolidated Mines Ltd (Koffiefontein. Finsch, Premier and Kimberley Mines) since 1989.

Jan 1, 1995

By McOnie A. W, Rutherford PG

A volcanic sequence is described from the Golden Cross Mine, Waihi, New Zealand. The sequence includes seven lithostratigraphic units comprising flow and pyroclastic units of Coromandel Group andesite and dacite and overlying Whitianga Group dacite and rhyolite which is intruded by the Golden Cross dacite porphyry and rhyolite dykes. The sequence is mineralized and is unconformably overlain bv_ two post-mineral units, the lacustnne Waitekauri beds and Omahine Subgroup andesite. Detailed structural analysis of mine data has identified four deformational events (D 1-D4) and related these to the gold-silver mineralizing events. Faulting was coeval with the mineralization and directly controlled the development, localization, style and geometry of the ore shoots. Mineralization developed in competent lithologies where dilation occurred during faulting. The Empire Fault is the master shear which controlled fluid flow. Mineralized veining developed in response to tectonic pulses occurring at slightly different stages as represented by the underground Empire vein complex and the open pit vein array. The mineralizing events culminated with the deposition of barren calcite veins. Post-mineral movement along the Western Boundary fault appears to have offset the ore body.

Jan 1, 1995

The use of black and white and colour infrared film in remote sensing of natural resources, is reviewed. In heavily-forested areas such as New Zealand, the main value of the method is in surveying the vegetation cover to detect the existence of plant communities characteristic of specific geological formations, By contrast, in and areas of Australia where the vegetation cover is sparse and where rocks and soils are well exposed, the method can be used in detecting different rock types or other geological differences.

Jan 1, 1971

The Illawarra Branch of the Australasian Institute of Mining and Metallurgy over recent years has established an enviable reputation for organising and conducting conferences, colloquia and symposia. And this Symposium must surely enhance that reputation. The subject of the Symposium, Seam Gas Drainage has become a matter of great import- ance to the Australian Coal Industry in a comparatively short time. Our short experience being due to our operations, until recent times anyway, not being unduly affected by gas. The Australian Industry, by virtue of its mines getting deeper and higher rates of extraction being required is now encountering the difficulties with gas which have for so long been part of the coal mining scene in many other countries. Because these gas emissions affect our working conditions by way of creating hazards and affect our production by way of bringing about cessation of operations from time to time this Symposium must be regarded as being very timely out here. I must congratulate the Branch Committee on the general set,yp :o.f the programme of papers. The classification of papers into four groups and the sequence in which the papers were presented provided an excellent flow through from introduction to finality. It is not my intention to further discuss individual papers - already they have been well discussed in this forum and as I understand it outside in the early hours of the morning,

Jan 1, 1982

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992

The Ocean Drilling Program is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (Legs) which each last approximately two months. These legs are designed by geoscientists from the 19 countries that subscribe to ODP. Australia and Canada share ODP membership under the banner of the AUSCAN Consortium. The Australian Secretariat of the ODP is housed at the Department of Earth Sciences at James Cook University, along with the AUSCAN Consortium office. The Canadian Secretariat is presently based at the University of Toronto. Both secretariats have major research interests in the ore deposits, both ancient and modem, and so there is currently a major drive by the AUSCAN ODP Consortium to make available data and technological information to the minerals industry. This type of information includes data from drilling hydrothermal sites such as the hydrothermally active TAG black smoker complex on the Mid-Atlantic Ridge, drilled during Leg 158, and the Middle Valley sulphide deposit, on the northern Juan de Fuca Ridge, which was drilled during Leg 139.

Jan 1, 1996

By Melcher G

The challenge to the zinc industry is shifting from maximum metal recoveries to the environmentally safe processing of the ore concentrates. The main source of solid residues from hydrometallurgical zinc processing is the iron content of the concentrates. Unfortunately iron precipitates from leach liquors contain various compounds which cause them to be considered as environmentally unsafe, unless they have been cleaned in subsequent process steps. This calls for separating the iron from hydrometallurgical processing as early as possible. For this purpose a process has been designed to eliminate the iron directly after neutral leaching the calcine. This is being done by direct smelting the neutral leach residue with a cyclone/top blowing unit. The zinc is recovered from the neutral leach residue as a metal oxide to be recycled to the zinc process. The iron is converted to a slag, which is resistant to atmospheric attack. Key data of the integrated hydro-/pyrometallurgical process are presented as derived from pilot plant tests by cyclone smelting and top blowing the slag.

Jan 1, 1993

By Bowden MW

Sintering of lead-zinc concentrates is practised by Sulphide Corporation to provide both desulfurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulfur dioxide gas for sulfuric acid manufacture.Moisture control of feed mixes is of paramount importance in the sintering operation and improvements in this area have realised increases in overall plant performance.

Jan 1, 1985