Search Documents

North Broken Hill Limited came into prominence as a producing mine at· the commencement of the present century, when a great many of the disabilities experienced in earlier mining operations th:rough lack of adequate stope filling had been overcome.The northern or narrower ore-body was first mined in the upper levels and, in the early stages, no great difficulty in mining was experienced. In depth, under the influence of its northerly pitch,. the wide southern ore-body entered the North mine between the 400 and 500-ft. levels. Owing to its flat dip and the relatively weak nature of the hanging wall and footwall, the value of close filling was recognized and this policy has been followed throughout the life of the mine. This feature undoubtedly contributed to the freedomfrom "creep" action to which some of the older mines had been subjected.The Broken Hill lead-zinc-silver ore-bodies occur as well defined replacements of favou:rable horizons, in intensely folded Pre-Cambrian sedimentaries. In the North mine two main replacement zones occur, the Gre being found where the beds are involved in a certain set of minor folds. The resulting ore-bodies are roughly elliptical in cross-section, the long axis of one being north-east of, and somewhat offset from the long axis of the other. The ore-bodies pitch eastwards at 40° and dip northwards at 60° in a fairly regularmanner. The southern Ore-body has an average length of 700 feet and an average width of 90 feet with a maximum width of 230 feet, whilst the nonhern ore-body on the lower levels averages 500 feet long and 40 feet wide.

Jan 1, 1940

By S MacKinnon, J Kok

Potential areas for improvement in flotation performance were identified during JKTech model development surveys in October 2003. Subsequent implementation of the JKTech recommendations in consultation with flotation cell manufacturer Outokumpu have resulted in gold flotation recovery increases of more than four per cent over a two-year period. One of these recommendations was the installation of High Shear Stators in the Cleaner and Recleaner flotation cells. The High Shear Stator installation project was justified based on simulations completed using JKSimFloat. Bubble size measurements completed before and after installation of High Shear Stators showed a reduction in mean bubble size of approximately 50 per cent in the Cleaner cells. Both Cleaner and Recleaner banks showed a significant narrowing of the bubble size distributions following the installation. Plant gold recovery increase resulting from the installation of High Shear Stators was 1.1 per cent, with a 1.9 per cent increase in flotation gold recovery and 5.4 per cent increase in flotation sulfur recovery. Based on the 1.1 per cent recovery increase and total project cost of less than $200 000, the High Shear Stator Project NPV was $8 200 000 with a 0.25 year payback period.

Jan 1, 2006

Based on twenty years of experiences of applying computers in mine water engineering in Hungary, a program package was developed for home utilization and for other users abroad as well. This program package has been adapted to the CAD System of Coal Mining of COMECON countries. The main features of the "mine water subsystem" in the CAD System of Coal Mining and short descriptions of the key programs of the package are presented in this paper. Foreword The serious water problems of Hungarian mining pressed and/or stimulated its professionals to apply computers for supporting their problem-solutions. The first trials of these computer applications in mine water engineering were dated from the sixties. Owing to its twenty years of experiences in computer appli- cations in mine water engineering the Central Institute for the Development of Mining in Hungary was requested to work out the "Subsystem of Mine Water" for the Computer Aided Design System ('CAD) of Coal Mines in COMECON countries. This paper gives a brief presentation on the main features of this "subsystem"with reference to significant components.

Jan 1, 1988

By E Wan, K Stokes

Since 1978, the nickel concentrator at Leinster has been subject to continuous change. In 1971 a significant nickel sulphide deposit was discovered on Leinster Downs Station, within three years the extent of the deposit was determined. In 1978 the Agnew Mining Company began production of nickel concentrate from the Perseverance Mine and continued to do so until production ceased in 1986. In 1988 WMC purchased the mothballed project and began the first phase of many expansion initiatives. Milestones in the life of Leinster have included:open cut mining of the Perseverance orebody and the discovery of the RockyÆs Reward orebody, as well as the metallurgical challenges in treating each of these; underground mining at both Perseverance and RockyÆs Reward; construction and commissioning of the WMC grinding and flotation circuits; variations in the reagent schemes, including the introduction of æliquidÆ reagents; development of mill linings to reduce maintenance; circuit re-configuration and simplification; development of Harmony open cut; strategies for increasing throughput at the drier; and changes to tailings facilities to cope with increased throughput. This paper outlines the steps which have been required to expand the Leinster Nickel Concentrator from 650 000 tpa to 2.5 Mtpa and those steps which will be required in the future.

Jan 1, 2000

By X Zheng, P Manton

Pebble recycle crushing circuit performance at Telfer has historically fallen significantly short of the design product P80 of 12 mm. An investigation was undertaken to evaluate the current pebble crusher circuit performance, quantify the optimum performance achievable with the existing circuit and examine the impact of pebble crusher performance on the overall grinding circuit throughput. The primary objective of this investigation was to develop an operating strategy that could consistently deliver the finest possible pebble crusher product to maximise the overall plant throughput.The pebble crusher specific energy (Wc) was proposed as a key control variable for pebble crusher operation based on the results of plant survey work. Over the range of pebble crusher specific energies encountered at Telfer, a strong linear relationship was found to exist between Wc and the crusher product size. This direct linear relationship between specific energy and crusher product size remained constant regardless of how the change in specific energy was generated, ie through changes to the crusher closed side setting (CSS), feed rate, liner profile or moisture content. Key findings for the Telfer pebble crushing circuit were: each 0.1 kWh/t change in Wc resulted in a 4.9 per cent to 6.0 per cent change in plant throughput, each 1 mm change in pebble crusher CSS resulted in a 2.2 per cent to 2.6 per cent change in plant throughput, and 0.57 tonne of new feed was displaced for each tonne of crushed pebbles recycled to the semi-autogenous grinding (SAG) mill. The presence of an existing 3000 tonne pebble stockpile between the SAG mill and pebble crushers provides an opportunity to manipulate the feed rate to the pebble crushers independently of the SAG mill pebble production rate. This flexibility, along with excess pebble crushing capacity, enables the pebble crusher specific energy to be maximised the majority of the time. Pebble crusher specific energy has subsequently been incorporated as an online crusher control measure to assist in maximising plant throughput.

Jan 1, 2009

By Fourney W. L, Weaver T. A

A large number of single borehole crater-forming shots were analyzed in terms of correlating the crater parameters with explosive weight. The objective was to determine a scaling rule for which the explosive weights varies over many orders of magnitude and covers many different geologic materials. Included in the data base are type and weight of the explosive, geologic medium and degree of saturation, charge depth-of-burial, crater dimensions, and crater rim (lip) measurements. An alternative scheme to the usual plot of scaled depth-of-burial versus scaled volume removed was desired. The proposed technique uses a plot of the logarithm of the explosive weight, Y, versus the logarithm of the slant length, R', calculated from the known depth-of-burial of the explosive and the measured crater radius. A plot of Log Y in kilotons versus Log R' in meters from all the crater tests in this data base resulted in a straight line with a of slope 0.31 and showed good correlation between the variables Log Y and Log R'. Since the crater data includes many geologic materials, different explosives (including nuclear tests), and large differences in charge weight, the straight line fit suggests that the type and strength of the geologic materials play a subordinate role to explosive energy in crater formation.\

Jan 1, 1990

By C X. Zhang, W K. Ru, S C. Hu

To study the creep properties and the energy evolution characteristics of the weakly cemented rock (WCR) in western China, the creep deformation damage law of weakly cemented mudstone (WCM) under graded loading and the energy evolution characteristics of each creep stage were analysed based on the triaxial graded loading creep test of WCR. The results showed that as the confining pressure increased, the creep failure strength of the WCM increased from 9.5 to 24.8 MPa, and the relative displacement of the mineral particles in the mudstone increased gradually, resulting in a reduction in the fracture angle from 79.7° to 58.3°. At the same stress level, the strain energy Ue, the total energy U, and the dissipation energy Ud all increased as the confining pressure increased, but the growth rates of U and Ud decreased gradually, while the growth rate of Ue remained high. At the end of the stable creep stage, Ue increased slowly with the confining pressure, while U and Ud increased rapidly with the confining pressure, and their growth rates were basically the same. At the end of the accelerated creep stage, the growth trends of these three energies were all positively correlated with the confining pressure, Ue was significantly lower than that at the end of the stable creep stage, and Ud and U were further increased. These results revealed the unique creep properties and energy evolution characteristics of the WCR, providing a theoretical basis for long-term stability control of roadways that are built with WCR.

Nov 29, 2022

By K McNabb, M H. Turner, P A. Jenkin

Mining of the Agnew nickel deposit commenced in 1970 using a variety of underground mining methods, though with mixed success due to the difficult ground conditions. WMC Resources Ltd acquired the operation in 1989, and commenced nickel production with an open pit. In 1995 all production reverted to the rejuvenated underground mine, using exclusively SLC (sublevel caving) methods. Currently the mine produces 1.4 Mt per annum, at an average grade of 1.74 per cent Ni. Underground mining of the Perseverance orebody has always presented significant challenges due to the difficult ground conditions in the weak and altered ultramafic rocks. The range of problems include areas of swelling minerals, intense and extremely weak shear zones, relatively high in situ stress, and in other areas very brittle rocks. Under these conditions rock mechanics input has been and remains a critical element of the mining strategy. Severe ground behaviour difficulties down to a depth of 500 m below surface prompted a review of the mining strategy for the large disseminated nickel orebody, including evaluation of alternative mining methods. However, sublevel caving was ultimately selected as the preferred method, and a re-design of the SLC cross-cut layout followed. A selection of rock mechanics investigations of interest are described, including complex virgin stress measurements, detailed ground behaviour monitoring, and the use of non-linear stress analyses to re-design the mine layout. Subsequent ground behaviour, support design and production scheduling are also described.

Jan 1, 2000

The paper describes the design of the dilute medium and medium recovery circuits installed at the coal preparation plants at the Cornwall Coal Company's Fingal Mine, and the BP Coal Australia's Howick Mine. These circuits maximize the use of clarified water for rinsing to improve the mass transfer of adhering medium from the coal surface into the carrying liquid, and have been combined with the use of a two stage magnetic separator. The separator utilizes a conventional concurrent first stage and a counter-rotation second stage. This combination results in high medium recoveries during both normal operation, and start up and shut down phases when large quantities of medium can be lost from a conventional circuit. Overall losses using this circuit have been estimated to be, 200g/t, over a twelve month period. Further advantages in plant operation are also obtained, especially steady operating conditions in the centre-tube pump tank, lower slimes contamination of the product, and lower quantities of non magnetics trapped in the separator concentrates. The techniques are particularly suited to incorporation in circuits treating coals containing high percentages of sticky and difficult clays, as are found in the Walloon coal measures.

Jan 1, 1987

By Prakash AJ, Singh PK, Dhar BB

Safety and stability of underground mine openings, coal pillars and water dams in the near vicinity of operating surface mines are endangered from excessive blast induced vibrations. This paper deals with the investigations carried out in four coal mines. Simultaneous measurements at equal distances from the source indicated higher level of vibration on the surface than those produced in the underground workings. The values of peak particle velocity (PPV) measured on coal pillars, body of water dam were lower than those measured on roof and junctions of the roadways. The parting of coal (3-4.5 m) between two sections vibrated with higher PPV compared to the roof of top section and floor of bottom section. In one case the influence of total charge fired in a round was significant in generation of vibration compared to the maximum charge/delay where monitoring was done vertically below the source.

Jan 1, 1995

By Carlson BL, Overton DD

This paper compares the designs of heap leach facilities for four precious metal mining projects in the southwestern United States. These four proposed projects are of small-to medium-size relative to other operating mines in the United States, and are either permitted or in the final stages of permitting. The differences and similarities in the heap leach facility designs are compared with respect to site conditions, operating conditions and regulatory requirements. This comparison provides a summary of the state-of-practice for heap leach facility design in the southwestern United States and identifies current issues in project development and process material containment.

Jan 1, 1997

In his introductory remarks Mr. MacKellar referred to three types of development which may be considered to compete with mining for land use. 1. Total Development - in which he cited urban development, and intensive agriculture. 2. Partial development - in which he cited pastoral, and in this category would come National Parks. 3. Non development - in which category would fall the primitive or wilderness areas.

Jan 1, 1971

By Manlapig EV, Mackinnon IDR, Laudr DW

Orebodies at Ok Tedi contain a number of different fluorine bearing minerals. Some of these minerals report to concentrate and are responsible for the presence of the penalty element, fluorine, within the concentrate. Previous analytical work has tended to examine geological samples for content, rather than determine the metallurgical behaviour of the different mineralogical species. This investigation utilised X-Ray Diffraction combined with Scanning Electron Microscope / Electron Microprobe to identify the fluorine bearing minerals in flotation test products. Seven fluorine bearing minerals were identified, viz., talc, phlogopite, amphibole (tremolite and actinolite), sphene, apatite, biotite and clay. Talc was found exclusively in the skam ore type. Phlogopite and amphiboles (tremolite and actinolite) were found to occur in both skarn and porphyry ores, while sphene, apatite, biotite and clay were found only in the porphyry ores. Of the fluorine bearing minerals observed, only talc exhibited natural hydrophobicity to any significant degree. Phlogopite and the amphibole minerals were found to be hydrophillic, whilst the remaining minerals occurred in insufficient quantities to determine the flotation behaviour. Ok Tedi copper concentrate fluorine content prior to skarn ore treatment in the mill (typically 350ppm) was previously identified as deriving from phlogopite, while talc was believed to be the source of intermittent high concentrate fluorine contents when skarn ores were treated. This paper provides supporting evidence for this belief, and reports the nature of fluorine bearing mineral flotation behaviour.

Jan 1, 1997

The Inquiry into the 1994 accident at Moura No. 2 Colliery included in it's findings that mine escape and rescue options for persons in underground coal mines were in need of review. The Inquiry recommended the establishment of industry working groups to report to the Queensland Chief Inspector of Coal Mines on matters including escape strategy and life support for escape from mines.One of these task groups examined issues relevant to self-escape from Australian underground coal mines and formulated recommendations and guidelines in response to the terms of reference and scope.

Jan 1, 1998

Portman Mining Pty Ltd very successfully operated the Ferro GullyNorth Mine in the Hamersley Province of Western Australia to satisfy a contract for the delivery of six million tonnes of iron ore in less than two years to the Mount Newman Mining Co Pty Ltd. The high-grade ore extracted from Ferro Gully North Mine was unusual in that, not only was it within the Joffre Member of the Brockman Formation, but it was rich in red ochreous hematite and martite and very low in phosphorus.

Jan 1, 2001

By P Cheluszka, M Jaszczuk, P Sobota

This paper refers to a new idea of stereometry of cutting drums of longwall shearers designed to get medium and hard to mine coals. A new way to place picks on a drum enables to readjust a number of picks being in contact with the body of coal to shearer haulage speed. Owing to this a remarkable increase in depth of a cut within the low range of haulage speed has been obtained. On comparing operating characteristics a considerable reduction in the specific energy consumption has been shown when using the units machined as per the new idea, in comparison with the units produced in series.

Jan 1, 2003

By Bailey DJ

Loader cut and fill stoping was first used at New Broken Hill Consolidated Limited mine in 1966. The equipment used included single boom pneumatic jumbos for drilling up- holes, diesel loaders for ore removal and diesel utility vehicles for rockbolting and servicing. Since 1966, there have been many modifi- cations and changes both in the equipment and stoping method. Twin boom pneumatic or hy- draulic drilling jumbos have replaced single boom pneumatic jumbos, electric loaders have replaced diesel loaders, diesel forklifts have replaced utility vehicles and "'flatbacking" has superseded uphole stoping. Concurrent with this has been the introduction of cable dowels in stope backs which has enabled loader cut and fill stoping to be used more extensiv- ely than in the past. There are now six loader cut and fill stopes at both mines and this paper traces the evolution of this method outlining the reasons for changes in technique and equipment.

Jan 1, 1982

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

In southeastern China, offshore Tertiarybasins are buried underneath the broad continental shelf areas from Taiwan to Hainan Island. These basins bear relatively similar characteristics of structure, stratigraphy and tectonics. Based on age and tectonic framework, these Tertiary basins are divided into two groups of Paleogene basin and Neogene basin (Fig.1 and 2). However, observations of extensional structures indicate that the Paleogene basins are rift basins; and the predominant structural features are NE-SW trending half grabens and fault blocks. In a regional scale, these half grabens and adjacent uplifts represent a horst-and-graben structural style. Neogene basins are downwarp basins lying on the tilting continental shelf. Late Tertiary sequences are relatively undeformed but locally with minor folding and thrusting during the Pliocene-Pleistocene.Seismic stratigraphy and well data indicate that the Early Tertiary strata are commonly tilted and disturbed as nonmarine to marginal marine facies deposited in the wedge-shaped half grabens; the Late Tertiary strata are generally parallel undisturbed marine facies accumulated in the enlarged downwarp basins overlying the infilled half grabens. In general, three major regional unconformities formed during the Late Cretaceous, the Late Eocene and the Middle Miocene. Widespread extrusive basaltic flows are commonly associated with these unconformities.

Jan 1, 1990

By Fuerstenau MC

Zinc cementation and carbon adsorption are both presently used for precious metals recovery from cyanide leach solutions. Each of these techniques exhibits unique processing features which renders them suitable to treat solutions with different properties and in different applications. In this study, the two processes are reviewed and compared. Operating data from a number of Merrill-Crowe precipitation and carbon adsorption plants in North America have been obtained and used in this analysis. The relative capital and operating costs for the two processes have also been considered.

Jan 1, 1993