Search Documents

Hydraulic mining shovels can be successively used at open-pit mining operation in severe climatic zone with air temperature interval from -700C to +450C typical for some northern region of the world particularly of Russia, Canada and Sweden, if they would be equipped by special preheating facilities for their diesel engine, water, hydraulic oil and lubrication systems. All shovels manufactured by the Komatsu Mining Germany GmbH for operation at ambient air temperatures down to -50¦C have cast and forged structural design elements, bolted connections made of special steel grades, electric cables with special insulation, flexible high-pressure hoses manufactured by ICE-Champion with connectors made of special steel grades.Generally at the temperatures below -25¦C the ordinary machine has to be stopped, the attachment should be placed in the parking position, the generator should be switched on, or the external electrical power supply connected, for the preheating equipment. For rapid start-up in winter after a long shutdown of a hydraulic shovel, there is a procedure for preheating of the main systems. It is applied for the following systems: engine cooling system, engine oil, hydraulic oil, pumps and drive motors of the propel gears, electric cabinets, machinery house, especially near the ventilation inlets and outlets.Start-up of the main drive engine is permitted at a hydraulic oil temperature of -20¦C, when it has a viscosity of 1000 cSt. In this case the rotation speed of the diesel engine crankshaft is lower by two times than the nominal value and this is the most favourable condition of start-up of the engine and hydraulic pumps and motors, which work with half of their rated rotation speed until the hydraulic oil reaches a viscosity from 100 to 10 cSt. After that the hydraulic system and the entire shovel begin to operate under normal conditions.

Dec 6, 2010

By J J. Moreno, J Willis, P Garvey

Many of the tailings storage facilities (TSFs) in Australia are upstream raised facilities for which the consolidation of the hydraulically deposited tailings is essential to the stability of the TSF. While much operational consideration is given to limiting the rate of rise of TSFs through careful management of deposition rates to achieve desired consolidation, the rate of embankment raise construction (RoC) is often not given the same level of consideration. Loading the tailings at too high a rate during construction could lead to upstream and potentially downstream failure of the embankment. The Tailings Retention System (TRS) at the BHP Olympic Dam Mine comprises upstream raised TSFs that are continually raised with a zoned embankment. Improving on 20 years of successful embankment raising, there was a desire to understand the acceptable RoC under varying operating conditions and assess upper construction limits to improve operational risk management. To understand the RoC, trial embankment raise construction pads were constructed at different rates and the pore pressure response of the underlying tailings material was monitored. The pore pressure data were used to calibrate the permeability and consolidation characteristics of the tailings in a finite element model (FEM) that replicated a typical embankment raise. The rate of material placement, location of the phreatic surface and construction load were varied in the FEM until failure was initiated. The results were presented as a period (in days) over which the various zones for the embankment raise could be safely constructed. The results indicate direct sensitivity to the depth to the phreatic surface prior to commencement of an embankment raise, as well as the point of application of the construction traffic load. This paper presents the study approach, challenges experienced in modelling the construction methodology, the study results and their relevance in the improvement of understanding of RoC at the BHP Olympic Dam TRS.

Jul 1, 2021

By R Salmimies

Choosing a ceramic capillary action filter is often favoured in processes where low energy consumption is important, such as the dewatering of iron ore. In addition, the performance of the filter medium is essential, and the possibility to regenerate the medium is an advantage compared to other types of filter media. Although low, roughly 8 - 9 w-per cent for iron ore concentrate, and even cake moisture is the primary goal of dewatering, the introduction of better filtration processes can result in significant improvements of water economy and material efficiency.As industrial beneficiation processes are often complicated in their chemistry due to impurities originating from the ore itself, from the up-stream processing equipment and from the process water used, the characterisation of the filter media after usage might provide relevant information on what actually takes place during long operating periods. The aim of this study was to obtain new information on the fouling of fi lter media in an iron ore process to enhance and develop the regeneration process of the media in the future.X-ray diffraction and scanning electron microscopy were used to characterise ceramic filter media used in the dewatering of magnetite. Principal component analysis and discriminant analysis were introduced to identify trends in the data. Two types of media blockages were found to play an important role in an acidic iron ore dewatering process: fouling by slurry particles and by in situ crystallisation of a calcium compound, of which the latter originated from the combination of process water and process chemistry.

Jul 11, 2011

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By V Louchnikov

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in situ stresses and associated seismicity with potential rock burst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. Its application in Australian underground mining, however, is limited due to the high labour intensity. This paper describes a method of mechanised installation of a chain-link mesh as trialled at Golden Grove, a base metals underground mine in Western Australia. A purpose-built mechanised roll mesh handler, developed in Australia, was used in this trial. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilising the hydraulic circuit normally used for the feed arrangement.A number of operational benefits have been identified during the trial, the main two being:•improved safety of underground personnel due to the reduced amount of manual handling, and•increased productivity due to the decreased cycle time (the trial suggests a 40 - 50 per cent reduction in time over the weld mesh installation method).Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rock burst prone conditions, the operational upsides recognised during the trial imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support.

Mar 21, 2011

By J W. Dong, Y M. Li, J L. Tian, Z H. Jiang

Electroslag remelting is widely used to produce various special steels, mainly because of its ability to provide high cleanliness and excellent homogeneity of ingot. Undoubtedly an optimal slag plays a key role in removing inclusions and enhancing the mechanical properties of a specific special steel. In order to improve the metallurgical performance of the slag in electroslag refining of die steel, a variety of slags have already been developed using traditional trial-and-error methods. Nonetheless, these slags may not be inherently optimal for the specific requirements of actual die steel refining processes. In this work, we have designed a CaF2-CaO-Al2O3-SiO2-MgO quinary slag system using genetic algorithms method aiming to remove the existing large size inclusions (D and Ds type) in high quality die steel. The comprehensive effects of five components (CaF2, CaO, Al2O3, SiO2 and MgO) were studied based on existing fundamental theory. The slag composition was screened considering the parameters such as melting point, electrical conductivity, calcium ion concentration, and appropriate viscosity etc. Furthermore, the candidate optimal slag was applied in the industrial production of die steel by electroslag remelting method. The detection results indicate that majority large inclusions (D and Ds type) have been successfully removed, showing significant advantage to traditional slags. This result has demonstrated the genetic method to be efficient and reliable. In addition, depending on the personalised demand of other steel and alloys, this method allows for the adjustment of the screening frameworks and processes to develop the candidate optimal slags. This method has not been reported previously in the field of electroslag composition design, and compared with the traditional trial-and-error method, the new method will save a lot of time and experimental costs.

Jun 19, 2024

By B Kilgariff

Flotation has been in use at Broken Hill for nearly 100 years, and the process has gone through many different optimisation studies over that time. This paper reviews the current flotation practice at the Perilya Broken Hill Mine, and details one of the recent optimisation studies conducted using mathematical modelling and simulation tools. The optimisation study consisted of surveys of the lead and zinc circuits, mapping of the floatability components of the ore and developing models of the lead and zinc circuits. The models were then used to conduct simulations to simplify the circuit. The study allowed plant personnel to identify optimum operating conditions for their current flotation cells, as well as possible improvements in circuit configuration and cell capacity.

Jan 1, 2005

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

By H Khoshrou, A Siamaki

Blast designs can have productive and non-productive impacts on downstream stages, mine productivity and operating costs. On the other hand, ground vibration, fragmentation, and back break caused by blasting impose damage and financial penalties and which must be controlled by blast design. One of the significant variables in blast design is the burden. In this study, the potentials of artificial neural network are investigated in prediction of burden in the Sungun copper open-pit mine. Input data were assembled through 18 blasting blocks according to different levels and experimental geomechanical investigation. To construct the model blastability index, uniaxial compression strength, hole diameter, specific weight of rock, rock quality designation and cohesion strength are taken as input parameters, whereas, burden is considered as an output parameter. Mean square error was used as the performance function and back propagation algorithm as the training function, containing four hidden layers and 14 data sets. Four sets of data were used to make sure that correct training had been carried out. This produced the coefficient correlation of 0.662.

Sep 26, 2011

By Bodnaras G. E, Sceresini P. A

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentration and high pressure to achieve extremely rapid gold dissolution rates. This is made possible by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device. The outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to-date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of 150 dry tonnes per hour at 40 - 45 per cent solids. Service life at this throughput is at least three months. The process may further be applied to high temperature leaching of refractory gold ores or other metals. Wear resistant metal or ceramic materials would be employed for this duty. Four mines are currently employing the Filblast Process for treating a variety of ore types ranging from highly reactive, almost impossible to treat, pyrrhotite/arsenopyrite to deeply weathered clay ore which forms a highly viscous pulp. The effect of shear thinning has resulted in improved adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately four million. Operating costs which include leasing and maintenance charges for the Filblast and pump power costs are about 16 cents per tonne. This is equivalent to about ten per cent of savings. Laboratory scale units having capacities up to 30 litres/min are available for test work but laboratory testing techniques so far developed do not accurately reflect the oxygen and cyanide savings which have been achieved in the plant.

Jan 1, 1994

By R Lachenicht, J Player, A Thompson, E Villaescusa

Kanowna Belle Gold Mine is a deep, high-stress, sublevel open stoping mine located near Kalgoorlie. Seismic activity during the development cycle presented problems, including concerns regarding the exposure of personnel. A number of seismic management systems were developed and tested to monitor seismicity and control the risk. It was recognised that a dynamically capable reinforcement and support system was required to be installed as part of the development cycle to reduce the risk of exposure of the underground workforce to uncontrolled movement of rock. The performance of a new Garford Dynamically capable bolt was measured in tests performed by the Western Australian School of Mines (WASM) at their Kalgoorlie Dynamic Test Facility. Detailed descriptions of the facility and data processing were reported by Player, Villaescusa and Thompson (2004) and Thompson, Villaescusa and Player (2004). The development of the Garford Dynamic bolt is described and dynamic testing results are presented and evaluated. This bolt was implemented in the mining cycle following the testing program; the observed performance is described and assessed in this paper.  

Jan 1, 2008

By G W. Wilson

Net solar radiation is one of the key factors affecting evaporation from soil covers on waste rock dumps. While net solar radiation is normally taken as a uniform parameter over a site for modelling purposes, there can be significant variation in the radiation actually received on various portions of the dump. These variations are a function of the difference in the cover slope and direction of exposure. A predictive model has been developed to calculate the actual radiation received on the dump surfaces, based on the net radiation data measured at a weather station on a horizontal surface. The model has been designed for application at any mine site in the world, and can be used in conjunction with evaporative flux models to help estimate the effect of three-dimensional variations in the cover surface exposure. The waste rock dump at Equity Silver site (located in British Columbia, Canada) has a barrier-type soil cover system to limit oxygen entry and water infiltration. This cover has been monitored for the past nine years. The new net solar radiation model has been applied to this site and the predicted net radiation was compared to the values of actual net radiation measured on the site. The predicted variations in net radiation over the three-dimensional surface of the waste rock dump have been applied to calculate spatial variations in potential and actual evaporation (or evapotranspiration) from the site. Preliminary analyses indicate actual evaporation from a site at this latitude could vary by a factor of two for exposed versus shaded slopes. The implications of these variations for the site are considered.

Jan 1, 2003

By S Dykes, R J. McCarthy, B Klein

There is growing interest in the mining industry on the application of ore sorting. While many are familiar with particle sorting, including the limitations that technology presents (e.g. throughput), bulk sorting, with its higher throughput potential, is less understood. Despite the potential to sort at higher throughputs, few operations have adopted bulk sorting processes, certainly not at large scale. It is suggested that the inability to reliably predict outcomes from bulk sorting may be limiting its adoption in mining projects. Consequently, an evaluation approach for bulk ore sorting has been developed such that mass pulls and grade upgrades can be predicted in the context of a mining study. The approach allows for evaluation of drill core assays and application of the consequently derived heterogeneity relationships to the block model for estimation of sorting outcomes. These processes were applied to conveyor-based bulk sorting for the CuMo project in Idaho, USA and are described in this paper.

Nov 10, 2020

By N Maistry, C Carelse, A Singh

Banded Iron Formations or more commonly known as BIF are sedimentary rock formations with alternating silica-rich layers and iron-rich layers that are mainly composed of iron oxides (hematite and magnetite), iron-rich carbonates, and/or iron-rich silicates. Considering the depletion of highgrade iron ore reserves in South Africa, there is a need to maximise resource utilisation through the exploitation of low-grade/uneconomic resources particularly BIF material, which makes up more than 65 per cent of current reserves. Previous test work conducted by alternative BIF sources globally indicates the need for fines processing in order to produce a concentrate. South African BIF however is amenable to coarse and fines processing producing an on-grade product or blended feedstock. C-Type material within South Africa’s Northern Cape Province grading at approximately 33 per cent Fe was supplied for research purposes. Top size optimisation via gravity Heavy Liquid Separation (HLS) tests was conducted. The laboratory results being perfect separation (Ep=0) were modelled to predict pilot performance, the results of which were tested on a pilot scale for the finest size fraction (-1 mm). It was observed that a top size of -2 mm provided optimum results in terms of upgrade and recovery, with crushing finer not necessarily producing superior results. At a target grade of 60 per cent Fe, recoveries of 65.6 per cent were achieved on the laboratory scale, whilst recoveries of approximately 58 per cent were achieved on the pilot scale. Targeting higher upgrades of 63 per cent would inevitably result in lower recoveries of 57.2 per cent on a laboratory scale and approximately 54 per cent on a pilot scale. This is in line with grades and recoveries achieved globally for BIF material albeit at finer grind sizes.

Sep 18, 2023

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

The general principles of technical due diligence best practice that are involved in assessing a mineral property in the early stages of its development are described and a bibliography of relevant papers is attached. The issues specific to the evaluation of gold deposits are highlighted. The Australasian Institute of Mining and Metallurgy's (The AusIMM) initiatives in this area, dealing with the proper public reporting of Reserve/Resource information (JORC Code) and property assessment/valuation (VALMIN Code), will be used as a framework against which the illegal tampering with drilling samples to artificially boost their gold content (salting) from the Busang gold deposit (Kalimantan, Indonesia), owned by Bre-X Minerals Limited (Calgary, Canada), will be reviewed. While the Busang saga was based upon fraud, through salting the samples, the general lessons to learn from such a scam are worth documenting. In Australia, most of those working in the mineral industry belong to long established professional institutes and consultant associations (eg The AusIMM or Mineral Industry Consultants Association [MICA]) that require their members to work within their technical limits and to comply with best practice guidelines, or risk being judged and found wanting by their peers in the context of strong Ethics Codes. There is also a strong interface between such representative professional bodies and the corporate and financial market regulators (ASC/ASX), which closes the monitoring loop. Canada has only now seen the wisdom of having this type of early warning system in place. Fraud and deliberate deception will be always possible, but deception on the enormous scale that occurred at Busang is most unlikely with proper surveillance systems in place and the use of accredited technical professionals. There should have been more hard data available about so big and rich a deposit owned by a C$6Bn company.

Jan 1, 1997

By G B. Smith, D Hillier, T Gibbons, D B. Donato, M D. Adams, S Davies, R S. Schulz

Responsible management of cyanide solutions and tailings on gold processing plants worldwide is an important aspect to these operations and is regulated via guidelines provided by the International Cyanide Management Code, an industry initiative designed to minimise cyanide risk to operators and the environment. Here we demonstrate the unprecedented causal relationships surrounding the saline (>14 000 mg/L total dissolved solids - TDS) and hypersaline (>50 000 mg/L TDS) cyanide solutions in gold plant tailings in the Central Goldfields of Western Australia, resulting in zero wildlife mortalities on three sites over the study period of almost one year. Wildlife interaction and ingestion is significantly lower than that experienced at other gold mine sites, with more rapid degradation of weak-acid dissociable (WAD) cyanide within the tailings storage facility (TSF). A rigorous chemical sampling using a novel æminimal accessÆ robotic sampler device and wildlife observation exercise was carried out at two hypersaline mine sites: Barrick Kanowna Belle (BKB) and Gold Fields St Ives (GSI) and one saline site, Barrick Granny Smith (BGS). The data was compared with available reported chemical sampling and wildlife observation data from a previously operational fresh water site (<2000 mg/L TDS) that had experienced wildlife mortalities, Case Study D (CSD). The comprehensive body of work, along with cyanide degradation test work carried out in the laboratory, was analysed via hypothesis development and testing, causation analysis and dynamic chemical modelling. The non-mortality effect on these sites appears to hold over a further four years of routine wildlife and cyanide monitoring by site personnel. This study has helped these three mine sites achieve and maintain full Compliance Cyanide Code status over a significant period while removing the need for operating the detoxification plants they would otherwise have required.CITATION:Adams, M D, Donato, D B, Schulz, R S, Smith, G B, Gibbons, T, Davies, S and Hillier, D, 2013. Hypersaline-induced reduction in cyanide ecotoxicity at gold operations, thereby obviating detoxification plants, in Proceedings World Gold 2013, pp 489-502 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By Swayn G. P, Floyd J. M

BHAS, together with the G.K. Williams Laboratory, and Ausmelt Pty. Ltd., has examined a number of possible alternatives to conventional silver cupellation in gas fired reverberatory furnaces. Of these alternatives, a Sirosmelt furnace was preferred for both technical and economic reasons. Small scale work on Sirosmelt processes was carried out at the G.K. Williams Laboratory at Melbourne University in 1985/86. Pilot scale work was carried out at the Ausmelt plant in Melbourne in July 1987. Board approval for construction of a full size plant was received in October, 1988, and construction of the plant is currently underway. The plant is expected to provide significant savings in operating costs and silver inventory. Hygiene around the furnace should also be greatly improved. An increase in cupellation rate of at least ten times is expected, compared with the conventional reverberatory furnace.

Jan 1, 1989

By Weller KR

Computer programs are described which help the metallurgist to process sample data from a plant survey; to carry out simple mass balance calculations; to present the results of circuit and equipment performance in convenient form; and to simulate the circuit response to changing operating conditions. The uses and limitations of these programs are explained by following through a case study of the sulphide flotation circuit at Cleveland Tin Ltd. The circuit was sampled, the data analysed, and some process inefficiencies established. Simulation calculations were then made to provide information on which to base decisions regarding possible circuit changes aimed at improving performance.

Jan 1, 1983