Search Documents

By Roberts T. J, Thomson I. A

Mill scale, which contains a high proportion of magnetite and wustite, was added to the feed to the Whyalla grate kiln pellet plant during the production of acid pellets for domestic consumption. Its addition resulted in increased production -rates together with reduced consumptions of bentonite, fireclay and fuel. Mill scale was particularly beneficial when treating feed containing difficult to process, earthy, high ignition loss iron ores. Test work in the laboratory and subsequent plant experience showed that the magnetite and wustite oxidised in the drying and preheat sections of the travelling grate. The additional heat reduced gas flows through the grate kiln system, aided the drying of green balls containing earthy ores and increased the preheat strength of the balls. These advantages were offset to some extent by higher power consumptions to grind the harder mill scale and process difficulties caused by the contamination of mill scale with oil and coke.

Jan 1, 1974

By N Esmaeili, M Saghaeian, L Hosseini, V Sheikhzadeh, R Hejazi

Ore roasting has long been used for beneficiation and assay upgrading of different ores. In this process, which is mainly used for sulfide ores, the ore is heated to a high temperature. More specifically, it is a metallurgical process involving gas-solid reactions at elevated temperatures. Some types of Iron ore are weak in magnetic properties. Hematite, goethite and limonite are classified in this group. Unlike magnetite, which shows strong magnetic susceptibility, these ores are hard to beneficiate through magnetic separation route. Many researches have focused on gravity separation and flotation routes for upgrading these ores and these methods have also been utilised in the industry. One of the methods to whose industrial application less attention has been paid is magnetising roasting in which the non-magnetic iron ore is transformed to magnetite which is further beneficiated through magnetic separation. In this study, magnetising roasting tests have been performed on one goethite sample in order to check the feasibility of using this method for this specific ore in industrial scale. It is worth mentioning that high intensity magnetic separation have been performed on this sample before but the achieved results were not promising. Results have revealed that through magnetising roasting magnetite content of the ore could be increased from 1.7 per cent up to about 25 per cent. FeO content of the feed sample was increased from 1.03 per cent up to around 9.25 per cent. Also optimum size distribution for achieving the best results in magnetising roasting for this sample has been determined through this study. The best results were achieved when the ore size was 0–10 mm. The effect of coal ratio, time and temperature on the process have also be studied. A coal ratio of 5 per cent, time of 30 min and a temperature of 850°C were determined to be the optimum conditions. Finally, the technical feasibility of utilising magnetising roasting for this specific ore has been confirmed.

Aug 24, 2022

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

By Y Zhuang, S La Brooy

The selection of the optimum process route for a new project has traditionally consisted of investigating existing options and ranking them in terms of cost, technical risk and environmental acceptability. With the current focus on sustainable development other factors now need to be considered. Life Cycle Assessment (LCA) of the process options can be used to extend the assessment in terms of their potential for earning renewable energy credits and in judging their ability to achieve greenhouse gas emission reductions. A rigorous life cycle assessment is demanding in terms of setting the baseline for comparisons and evaluating the elements that make up the emission profiles of the process options. However, a simplified LCA can provide a useful tool for comparing different process options. This approach can be combined with traditional assessment criteria to rank the options available to the project. GRD Minproc has been intimately involved in executing LCA calculations for different municipal waste treatment options. This paper applies a similar LCA methodology to investigate the greenhouse gas implications for different options for copper processing. The process options considered are:concentrator û sale of concentrate to smelter, concentrator û on-site mini smelter, and concentrator û leach SX/EW. The paper then goes on to consider the operating cost implications that could arise with the introduction of carbon taxes or carbon credits and how these might impact on the future choice of flowsheet.

Jan 1, 2002

The Use of Automated Mineralogy to Interpret the Batch Flotation Performance of Merensky Reef Ore

Sep 13, 2010

By A F. Cooper

Otago Schist in the Mount Patriarch, High Burn and Cameron Creek areas of northwest Otago grades from textural grade IIA in the east to textural grade III in the west. The entire region is of the actinolite-pumpellyite metamorphic facies. Lithologies in the area are interbedded turbidite sequences comprising pelite and psammite together with pebble conglomerate, greenschist and metachert horizons. The mineral assemblage of the schist is typically quartz-albite-epidote-actinolite-pumpellyite-chlorite-stilpnomelane-calcite. A good foliation is well defined in the area and is predominantly parallel to bedding, except in hinges of mesoscopic isoclinal folds. The structure of the area appears to be defined by a large southwest plunging isoclinal fold defined by bedding with a steeply dipping axial planar foliation. Kink folding and dextral strike-slip faulting in the area postdates the ductile phase of deformation. Pods of rhodonite, rhodochrosite, spessartine garnet, coombsite, caryopilite, Mnstilpnomelane and Ni-Cu-Zn sulphides were found in concordant metachert layers in the Mount Patriarch area. Metachert was also found in float in the Cameron Creek area. Malachite occurrences relating to copper mineralisation were also noted in a green metachert horizon on the eastern flank of Mount Patriarch. The coombsite, in only the third observation worldwide, is the most Fe-rich variety reported.

Jan 1, 2003

Probabilistic seismic hazard analyses (PSHA) have now gained wide acceptance in the development of design criteria for major projects. When used with regional criteria the procedures have also allowed the preparation of more rational seismic zoning maps. Seismic zoning maps using various levels of results from PSHA studies around the Pacific Rim now include Canada, Indonesia, New Zealand and the United States. Some Pacific Rim countries such as Chile where the seismic exposure is dominated by subduction events have no subdivision into separate zones.Approaches to risk based zoning are being considered in several Pacific Rim countries including Australia. Australian studies must face problems similar to parts of the Eastern United States where seismic activity is low with irregular and infrequent occurrences of moderately large earthquakes. The perception of the seismic exposure by both regulatory agencies and the public at large is different when considering areas of low seismicity. There is therefore a need to make different interpretations of the results of PSHA studies in these areas of low seismicity. The aim of this paper is to explore some of these differences by comparing the results from two site specific studies from areas with widely differing seismic activity rates.

Jan 1, 1990

By R Grogan

Nautilus Minerals (Nautilus) is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.During the environmental impact assessment and project development phase, Nautilus completed a number of hydrodynamic modelling exercises in order to predict the nature, volume and extent of the plumes likely to be generated by the sea floor mining tools and return water discharge at the sea floor.The modelling was conducted using the suspended sediment fate model (SSFATE), developed by the United States Army Corps of Engineers and RPS APASA engineering consultants. The SSFATE model was originally developed in order to predict and manage dredging plumes, and has since been adapted for deep ocean sea floor mining. The model uses a Lagrangian approach to remove the limitations of grid resolution, and simulates far-field effects of sedimentation plumes by assuming that the average transport and turbulence associated with currents are dominant over the initial turbulence at the release point. The random walk procedure utilised in the model tracks particle size classes as they disperse and settle, and also takes into consideration any re-suspension that may occur following settlement (RPS APASA, 2014).CITATION:Grogan, R, 2016. Predicting, assessing and managing sediment plumes generated by sea floor mining, in Proceedings Life-of-Mine 2016 Conference, pp 124–127 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

This paper discusses the significant land use changes that have occurred in the Latrobe Valley during 150 years of white occupation. The developments and changes were haphazard and made with little thought as to their setting or their environmental consequences. As a result many landscape and land management problems have not been addressed.This paper contends that the mistakes will continue unless an overall plan for the landscape of the area is developed and implemented. The concept of 'Greening the Valley' is introduced. It aims to provide focus for a comprehensive co-ordinated plan which caters for the need to restore the landscape and the need to provide for future land use. The plan will seek to draw on three major landscape features of the Latrobe Valley: the natural setting of the hills, rivers, valleys and forests; the agricultural land use including the forestry plantations; and the industrial complexes and urban areas.Rehabilitation of mining areas is a key element of the plan but must be put in a regional context and not be treated as an isolated function of a single organisation. A major challenge will be to integrate the worked out areas into useful and significant landscapes. The paper concludes by explaining the process that will be followed in an attempt to realise the concept.

Jan 1, 1992

By T Rock

This paper looks at recent advances in the United Kingdom (UK) tunnelling industry with particular reference to the A3 Hindhead Project. A 1.8 km long twin bore tunnel is the centrepiece of the A3 Hindhead scheme, which commenced construction in 2007 and is being delivered under a UK Highways Agency early contractor involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe-shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunnelling medium is a æsoft rockÆ sandstone for which there was little previous tunnelling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240 m long section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels. The innovative approach to the design of the following is discussed:the æpermanentÆ primary lining,an observational technique allowing optimisation of the steel pipe umbrella design,a plain concrete secondary lining designed for resistance to a hydrocarbon fire, anda spray-applied membrane.

Jan 1, 2008

By R O’Sullivan, D Taylor, J G. McLellan, B Miller

The Mount Isa copper deposit is located adjacent to the city of Mount Isa, Queensland, and lies within a series of Palaeoproterozoic to Mesoproterozoic Superbasins. The deposit is hosted almost entirely within the Urquhart Shale (US), a unit of the Mount Isa Group sediments and part of the Isa Superbasin. The copper mineralisation is separated into two distinct orebodies: the X41 mine (1100 and 1900 orebodies) and the Enterprise mine (3000 and 3500 orebodies). The orebodies are situated in the hanging wall of the major controlling structures, the Paroo Fault, which has juxtaposed older basement Eastern Creek Volcanics against the younger Mount Isa Group sediments cf 1655 ± 4 Ma. Conjecture remains over the exact timing of this thrust event. However, it is clear that inflections on the Paroo Fault have a close association with the orebodies and are an important structural feature in the mineralisation of the Mount Isa copper deposit.The life-of-mine is reducing steadily and new geomechanical modelling techniques were employed to target structurally controlled mineralised zones in three dimensions. Following a structural review of the mine using underground mapping, structural data and core shed observations, a conceptual 3D mine model was constructed utilising existing data modelled in MineSight®. This conceptual model included all the main lithological units and structures. The conceptual model aimed to test the effects of deformation on the main lithological and structural components of the system and attempted to highlight areas of anomalous stress and strain that may indicate a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE–SW compression) and D4 event (SE–NW compression), which are considered to be responsible for the current location of the mineralisation.The fully coupled 3D finite element analysis models resulted in highlighting anomalous patterns of stress and strain and subsequent fluid flow as a result of the two deformation events. The NE–SW D3 simulation provided the best correlation with the known distribution of mineralisation. This event also indicated several areas on the Paroo Fault and within the US that have potential to host further areas of mineralisation. The SE–NW D4 simulation provided less of a correlation with known mineralised zones. However, this event may have been responsible for post mineralisation re-mobilisation of copper on a relatively small scale. Areas of maximum shear strain, shear stress, volumetric strain and fluid flow correlated well with areas of minimum principal stress and provided the best overall match with known mineralised zones. Furthermore, several additional highlighted areas provide a high potential for further discovery of copper mineralisation. Recent exploration drilling north of the Enterprise mine 3000 orebody, utilising geomechanical modelling as part of the targeting criteria, intersected copper mineralisation, providing further validation of the modelling results.CITATION:McLellan, J G, O’Sullivan, R, Miller, B and Taylor, D, 2014. Geomechanical modelling of the Mount Isa copper deposit – predicting mineralisation, in Proceedings Ninth International Mining Geology Conference 2014 , pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Operational effectiveness is fundamental to any operation, becoming highly topical in those experiencing less than optimal output from their fleets. It is all encompassing aiming to identify those factors that could be improved within production and suggesting solutions in order to optimise the existing fleet and obtain the greatest capital return on expenditure.Argyle Diamond Mine (ADM) is a large open cut diamond mine located in the East Kimberley region of Western Australia, approximately 180 km south of Kununurra. It is owned and operated by Rio Tinto on a two week on/two week off roster fly-in/fly-out from Perth or drive in/drive out from Kununurra. Through benchmarking the operation between January and June 2002, a study was undertaken allowing identification of areas falling below target. Following this, analysis of annualised hours and production downtimes were undertaken to quantify the potential gains of improvements in these areas. Strategies were then identified as stated in the 2002 mine plan, in operational effectiveness meetings, and by staff members. This project aimed to maximise direct working hours through determination of the main issues hindering performance. External and internal factors were considered and a continuous improvement program (CIP) was developed. The CIP aimed at internal site-based improvement teams to identify and implement solutions for improvement on a day-to-day basis.

Jan 1, 2003

Drag pick roadheaders and continuous miners have been applied in the coal mining industry for several decades, having replaced drill-blast methods as the primary means of excavating coal and coal-measures strata. The generally harder rock types associated with metalliferous mining have precluded the use of such machines in the past, however, developments in machine technology and increasing labour costs and environmental constraints suggest that there are now likely to be applications suited to the method. Metalliferous mining engineers are generally unfamiliar with the machines themselves and with the fundamental criteria controlling rock cuttability. This paper gives an introduction to the machines and the controlling factors.

Jan 1, 1987

By M Goers, M Almond

"The use of reverse circulation (RC) drilling for grade control sample collection was selected by the Pueblo Viejo Mine Geology department at the recommencement of the operation in 2010. This method was selected because it allows: for multi-bench drilling (60 m hole depth, four benches of mining) to aid mine planning and provide a detailed close spaced drill data comparison with the reserve model angled drill holes to optimise the drill hole interception of the vertically controlled mineralisation dry sample collection in areas of excessive surface and groundwater mining operations to commence with the long assay return period (due to the need for the samples to be shipped overseas for analysis) until the on-site laboratory is operational.To date, 118 302 m of drilling has been completed throughout the operations of two open pits: Monte Negro and Moore. Two drill rigs (contractor and site-owned and operated) with three generations of sampling systems have been used to date. Throughout the drilling a 20 per cent quality assurance, quality control (QAQC) sample check (blanks, field duplicates and standards) have been used to check the drilling and laboratories performance. In addition, a total of 1104 fines samples were collected to compare the drill chip samples collected and the fines lost with two of the sample systems used.The drilling to date has highlighted the need for a complete and coordinated system to be used before sufficient confidence in the quality of the samples collected is achieved.The complete system must be set-up and coordinated to obtain the best quality sample possible. This complete package includes: drill bit size and shape for the rock being drilled and mineralisation targeted face sampling hammers with the correctly sized hammer shrouds sample hose routing to reduce sample flow turbulence and choking blow-down valves to eliminate drill hole water that has entered the drill string during rod changes correct drilling techniques targeting sample quality a sample system that captures the fines for inclusion into the sample.These improvements can be obtained without reducing the drilling rates.The measurements required to demonstrate the improvement in the sample quality will be the focus of future work within the department.CITATION:Goers, M and Almond, M, 2012. Bit to bag - The importance of a total coordinated system in reverse circulation drilling, in Proceedings Sampling 2012, pp 65-72 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022

Past and present developments in the use of blast furnace slag in the manufacture of glass are outlined. The crude slag from Port Kembla is beneficiated by the Mineral Resources Division of Australian Consolidated Industries Ltd. at Mascot using a dry magnetic separation process which reduces the iron level in the slag to an acceptable value, The chemical and physical properties of both the crude and beneficiated slag are given and compared with those of other slags used in the manufacture of glass. Slag is added to intro- duce alumina into the glass and its addition to the glass batch also results in faster melting and refining. Slag was first used in Australia in 1968 and its use has increased steadily year by year. At present about 16 000 tonnes of slag are used per year, mainly in amber and white glass. Beneficiated slag is used'in three plants to supply all the alumina required in the amber glass and in four plants to supply part of the alumina required in the white glass, the amount added depending on the acceptable iron level in the glass. Slag is also used in limited quantities in the manufacture of both dark and light green glass.

Jan 1, 1979

By S Mitra, D O’Dea, N Barrett, T Honeyands, E Copland

This work describes a novel mapping technique that allows the direct overlay of calculated local phase equilibria on micrographs of the physical system. The technique demonstrated integrates FactSage™, ver 8.2 (by Thermfact Ltd. and GTT-Technologies) phase equilibria calculations with mapped compositions determined by Scanning Electron Microscope – Energy Dispersive X-ray Spectroscopy (SEM-EDS) to visually express calculated properties while preserving the spatial information of the sample. The developed methodology is used to analyse interrupted blast furnace softening and melting tests containing mixed burdens of lump and sinter. Tests are interrupted at 1300C and cooled to room temperature for analysis. Phases present at room temperature are analysed to infer the liquid fraction and phases present at high temperature. Analysis of the interface regions between the dissimilar burdens allows insights to be gained into the interaction mechanism. During the transition from solid to liquid, migration and interaction of liquid oxide across the interfaces of the dissimilar burdens has been observed and demonstrated to impact softening and melting performance. Specifically, interaction of the oxides generated by lump (primarily FeO, SiO2 and Al2O3) and sinter (primarily FeO, CaO, SiO2, Al2O3 and MgO) are analysed, and the occurrence of a range of new mineral phases such as merwinite, melilite, olivine and bredigite observed.

Jun 19, 2024

By G J. Halstead, R C. Steinhaus

The True Pipe® in-line sampler was developed in an attempt to address the need for a mechanically reliable and correctly designed sampler to suit one-dimensional pressurised slurry pipelines, often found in metallurgical process plants but for which no reliable and representative sampling solution as yet exists.The design, whose operation is based on the principle of symmetry, is described by Dominique François-Bongarçon (2005) with the synchronous opening and closing of relevant valves. It representatively isolates portions of the particulate material stream at predetermined intervals for effective extraction of primary increments for subsequent sample compositing.Theory of Sampling applicable solutions have proven elusive in flowing pressurised particulate material streams, with various attempts to date not having formulated a viable, mechanically reliable and acceptable design.Compliance to sampling theory is critical, and a number of tests were conducted where certain operating parameters were altered to determine their influence and sensitivity on sampling representativeness.The results of the initial series of tests performed on a carefully designed rig are presented, with additional work discussed for necessary investigation in the near future.Getting closer to a robust, economic and correct design for this challenging application in the minerals industry may now not be that far away. Plant management staff will see improved metallurgical mineral balances around their process plants and significantly reduced sampling discrepancies, particularly in tailings applications. Improved quality control is now possible where, due to plant head room constraints, classical cross stream sampling methods cannot be employed.CITATION:Steinhaus, R C and Halstead, G J, 2014. True pipe sampler – a correct design utilising the principle of symmetry in pressurised slurry particulate streams, in Proceedings Sampling 2014 , pp 127–134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By J L. Merritt

The mining industry seeks to engage with and respond to stakeholders through open consultation processes during the various phases of a mining project (Department of Industry, Tourism and Resources, 2006). Two Australian Coal Association Research Program (ACARP) funded projects conducted in the Bowen Basin coalfields in Central Queensland investigated the use of a stakeholder panel for the evaluation of mine site rehabilitation. The panel members were drawn from the local and regional area, and represented neighbouring landholders, traditional owners, AgForce, local government, conservation groups and non-governmental organisations (NGOs) such as Greening Australia and the Fitzroy Basin Association. The approach of utilising stakeholders to establish rehabilitation criteria was proposed as an alternative to the established practice of assessing rehabilitated areas against a suite of quantitative completion criteria; eg >70 per cent vegetative ground cover or <5 t/ha/a soil loss. The basis of this approach recognises the reality that the definition of completion criteria has proved problematic over the last 40 years with no broad consensus reached on the suite, let alone the metrics; eg the exact cover level that will benchmark acceptance of the mine site rehabilitation.CITATION:Merritt, J L, 2016. Zooming out – learning to see rehabilitation through stakeholders’ eyes, in Proceedings Life-of-Mine 2016 Conference, pp 163–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940's, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998