Search Documents

Increasing demands on quality of metallurgical grade alumina and for lower production costs led to the development of a new fluid bed calcining process. The process, jointly developed in Germany by Vereinigte Aluminium Werke A. G. and Lurgi Gesellschaften m.b.H., takes advantage of modern chemical engineering methods such as counter-current flow of combustion air and solids, direct heat-exchange between combustion air and fine solids, and near stoichiometric combustion of oil in a fluid bed. Using a two-stage Venturi-type suspension preheater for heat-recovery from combustion flue-gases, the circulating fluid bed technique with internal oil combustion at 220°F for the calcining step and a five-stage fluidized bed cooler for heat-recovery from calcines, the process gives an outstanding heat-efficiency. In a first industrial plant for 560 sh. tons/day of alumina heat consumption figures of less than 1·400 B.T.U./lb Al203 g were achieved.

Jan 1, 1972

By Jones S. C

The problem of sealing a fluid serieite zone at a hole depth of 4000 ft was overcome by using a composite non-return valve plug and rod assembly which enabled cement to be forced under pressure into the zoneà

Jan 1, 1966

This paper contends that optimisation of energy resources through active control and predictive simulation modelling is possible, and that such monitoring leads to large savings in the electricity costs of hot mines (where refrigeration has to be employed). In addition, active monitoring and control can positively affect the establishment of a safe, healthy and productive working environment. In the entire optimisation process certain guidelines were set to ensure that the requirements of the Mine Health and Safety Act were met (South Africa). Varying the quantity of air supplied underground by means of variable speed drive (VSD) fans is one of the crucial factors in the interactive approach towards the optimisation of ventilation, as is refrigeration and the pumping requirements associated with refrigeration. This article highlights the interaction between the amount of air supplied and the effect it has on refrigeration requirements underground. This article also considers the effect that this would have on contaminant control. Various tools are available for ventilation and cooling design for mining. A lot of these tools are based on the assumption of steady state conditions and do not take into account instantaneous changes in conditions, day-to-day, or hour-to-hour (such as for temperature and contaminants). They also do not take into account the optimisation of energy resources related to the creation of the acceptable underground conditions. With these tools worst-case and best-case scenarios are identified, and strategic decisions are made accordingly. Currently, the amount of the fresh air, the velocity of the air, and its general temperature in the mine are only changed when one production phase changes into another (or when unacceptable conditions occur as a result of poor design or neglect). This means that during a specific production phase (which can last for several months), there can be an oversupply, or undersupply, of energy resources, which will obviously affect the concentration levels of the various contaminants (through under or oversupply of air).

Jan 1, 2005

The detailed engineering of a coal preparation plant is important from the point of view of optimum constructibility, operational security, ease of maintenance, operating costs, meeting environmental goals, safety, plant housekeeping and reduced corrosion and erosion. This paper reviews the several large coking coal preparation plants engineered by Fluor Australia in the past 10 years, and changes and trends apparent for detailed engineering of future plants. Areas of engineering to be covered are coal feed preparation, conveyor design, plant layout, electrics and instrumentation, noise attenuation, erosion and corrosion protection, magnetite handling, rejects and tailings disposal and coal stockpiling and blending.

Jan 1, 1982

By A B. Christie

Space-based synthetic aperture radar (SAR) data is becoming available over much of the world, includingNew Zealand. Radar imagery has a number of very advantageous features, including all-weather capability; it also has artifacts, such as layover, which require processing before these data may be used to best effect.   This paper gives an outline of SAR, details the image processing required, and discusses the use of the first New Zealand Japan Earth Resources-1 SAR data to aid geological mapping on the Coromandel Peninsula.

Jan 1, 1994

When xanthates or dithiophosphates are used as collectors in sulphide ore flotation, adsorbed species may be identified by gas chromatography of the volatile products formed during low temperature pyrolysis. For collector additions ,as low as 20 g/tonne of ore, pyrolysis of the flotation products usually gives' an olefin directly related to the particular xanthate or Aerofloat reagent used. The method is able to provide valuable qualitative and quantitative data relating to the extent of collector adsorption and the resulting changes in the hydrophilic or hydrophobic nature of the mineral surface.

Jan 1, 1974

Inevitably the 'post-boom' era has changed the emphasis of many mining companies away from new project development and expansion to optimisation of existing operations. However, regardless of the project, high quality ore characterisation will remain of the utmost importance. In the case of new project development the need to understand the breakage characteristics will remain as important as it has always been. In optimisation projects, however, where it will be required to get the very best from existing comminution circuits, accurate geometallurgical modelling will take on an increasingly important role. However, these requirements, in both new development and optimisation projects, are likely to be at odds with budgets as these will be tight. Hence obtaining the best value for money will be essential. This paper discusses the elements that need to be satisfied for ore characterisation programs to be successful. Some of the issues covered will be: ore variability and sample selection, test precision, problems with the use of non-standard testing equipment, and the value of databases.

Jan 1, 2009

By Ward S. C, Gardner J. H

In 1990, Alcoa of Australia Limited was elected to the Global 500 Roll of Honour of the United Nations Environment Program for the environmental management and rehabilitation of the bauxite mines in Western Australia. This award placed Alcoa in the international best practice category. The story of constant improvement spans more than 20 years from a 'trial and error' start to a strategically focussed and research driven program today. The main driving force has come from within the company, against a set of strong corporate values and a well publicised Vision based on 'excellence through quality'. Along the way public opinion, action group protests, increased legislative controls together with the professional competence of internal and external environmental resources have all played a part in arriving at the level of current environmental management and mine rehabilitation performance. There were numerous lessons learned here during the evolution and maintenance of best practice. These included: I . To work diligently in obtaining a vision or strategic intent on mine site rehabilitation and environmental management - don't be easily dissuaded.

Jan 1, 1995

Hindustan Zinc Limited (HZL) is one of the leading base metal producers in India. It operates a two-smelter Complex at Visakhapatnam, Andhra Pradesh. At this zinc-lead smelter zinc is manufactured by the conventional hydrometallurgical route and lead is produced by Blast furnace technology generating residues or wastes which contain substantial quantities of metal values. Disposal of such wastes is a problem in any non-ferrous industry. Both the stringent environmental regulations and the changing industrial scenario emphasise the need for industrial research to find economically viable and environmentally friendly technologies to recover the metal values from these waste materials. The in-house R&D Centre at Vizag Zinc Smelter (VZS) thinking globally re-engineered its activities and major thrust was given for converting waste to valuable metals and metal compounds. Basic analytical chemistry with the hydrometallurgical concepts has been adopted in developing these innovative technologies. In this paper attempts are made to provide a clear history of the different waste raw material, the process developed for each raw material and their superiority of over other parallel work. Most of the processes described here are pilot plant tested and under patenting. The process flowsheet, results obtained and advantages of each process are presented. This paper provides a consolidated approach through which the varied smelter waste materials can be processed with cost effective and eco-friendly innovative technologies. In-house R&D efforts at VZS with its contribution and achievement in converting æwastes into wealthÆ technologies are presented in this paper on the following the major thrust areas:recovery of zinc from liquid effluent; recovery of zinc from effluent treatment plant (ETP) gypsum sludge; production of highly pure electrolytic zinc metal powder from zinc bearing gypsum residue/sludge generated at the effluent treatment plant; hydrometallurgical recovery of copper as copper sulphate solution which can be used for CuSO4.5H2O, copper cathode/copper metal powder from copper-cadmium cement; recovery of manganese, lead and silver from anode mud generated at Zinc Cell House and 4-metal extraction/recovery of manganese, cobalt, copper and nickel from Indian ocean bed manganese nodules; recovery of zinc, lead, silver and sulphur values from silver concentrate residue generated at the froth flotation process; recovery of silver and lead as lead-silver sponge/lead-silver sulphide concentrate from lead bearing residues; recovery of lead, silver and copper from copper matte; recovery of antimony as antimony metal or lead-antimony master alloy from antimony bearing dross; and recovery of nickel and dimethylglyoxime from Ni-DMG complex.

Jan 1, 2000

This modern plant was installed with the object of treating all oxide ore and payable dump material by the cyanide process.The plant is located on a ridge on the eastern side of Linda Gully. The mill -site has a slope to the south of 1 in 4.The new plant is of steel and concrete construction and was specially designed to suit the climatic conditions which exist at Mount Morgan.THE COARSE CRUSHING PLANTThe ore received from the, mine is dumped into a 600-ton steel bin which is commanded by a 3 ft. 6 in. gauge railway,The mine ore is conveyed by steam locomotives in rakes of five self-dumping 7-ton railroad cars. The dump material is mostly loaded by bull-dozers and conveyed to the binsin large motor lorries. Located on the top of the bin is a heavy railroad grizzly having 12-in openings through which all ore must pass.The flow of ore from this steel bin is controlled by a No. 7D 3-speed Ross chain feeder. It should be mentioned here that, although the bottom of the steel bin is inclined at an angle of 45°, it has been found, owing to the clayey nature of the oxide ore, that the live capacity of the bin is only about 50% of the total capacity.

Jan 1, 1939

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

Laboratory scale equipment was developed to recover zinc as oxide fume from granulated lead blast furnace slag. The cyclone furnace process is characterised by high treatment rates combined with continuous and independent operation.Results were sufficiently encouraging to warrant pilot plant scale trials being undertaken.INTRODUCTIONSince granulation of lead blast furnace slag started at Port Pirie in 1921 the stockpile of this material has increased to nearly 5 million tons which averages 17·5 per cent zinc by weight. Although a number of processes for recovering the zinc have been examined, economic considerations indicate that a slag fuming process is likely to be most suitable.In the conventional slag fuming process zinc is extracted by injecting pulverized coal and air into a molten slag bath. By maintaining a suitable air to coal ratio the oxidised zinc contained in the slag is reduced to metal. Volatilization of the zinc is followed by reoxidation in the gaseous phase with the addition of further air above the bath. The zinc oxide fume so produced is collected by normal gas cleaning methods.By examination of the thermodynamics of this process Bell, Turner, and Peters (1955) determined the zinc oxide activity of the slag over the duration of the fuming cycle.A combination of high temperature and high carbon monoxide/carbon dioxide ratio was found necessary for rapid zinc elimination.Since melting of the slag is an essential step in the slag fuming process, only two treatment methods appeared possible at Port Pirie until recently...

Jan 1, 1964

By M F. Lee

In order to make good decisions, as to whether large diameter raise bored shafts can be constructed in blocky rock at a particular location, mine planners, management, geotechnical engineers and contractors must understand and consider a range of geotechnical issues. Firstly, mine management must ensure that adequate time and resources are available to find appropriate shaft sites. Deep weathering, adverse structures, groundwater, etc might mean that the most desirable location, with respect to other mine development, might not be suitable. Special site investigation drilling, etc may be necessary. Even then, alternative construction options might be necessary, other than just reaming through to the surface. A site investigation borehole should then be drilled to investigate specific and general ground conditions along the raise alignment. Often, only small sections of weak blocky rock dictate raise stability. While the empirical McCracken and Stacey method is typically used in Australia to assess raise stability and assess geotechnical risk, until recently it had no published performance data.An Australian database of raise performance now exists and is presented below, courtesy of an industry survey by the Eastern Australian Ground Control Group. Raise diameter and ground conditions (in terms of a lower bound Qr value) is presented for 50 cases versus raise performance.

Jan 1, 2008

By H R. Phillips

The ventilation and refrigeration design of underground mines is an important aspect, when new or existing mines are considered and places a great responsibility on engineers tasked to do so. The current trend for both local and international underground mines is to extend their search for valuable ore reserves deeper below surface. In South Africa, the predictions are that about 40 kt of actual gold still lies in situ, ready for extraction. As mines extend their search for minerals of economic value deeper and deeper into the earthÆs crust, ventilation and refrigeration aspects of such mines become more prominent than before. The planning and design of the required ventilation and refrigeration within these mines, over their expected lifetime is important including the practical implications of such designs. Technology changes and improvements need to be incorporated into ventilation and refrigeration designs, where possible and advances in this specialised field explored. This paper explores ventilation and refrigeration design aspects within the underground mine sphere. Aspects such as mining depth, virgin rock temperature (VRT), mining methods, and different cooling applications available including ventilation supply are reviewed in design applications. Heat generally becomes a significant aspect to counter in these mines and they are not always necessarily deep mines.

Jan 1, 2005

By Mozley R

Contaminated sediments are a multinational problem. A crucial factor in solving an environmental problem is knowledge of, not only the amounts of polluted soil, the contaminants involved and their concentration, but also the historical background of the problem. Processing polluted soil is a tailor made activity based on rational decisions resulting from a detailed treatability study. Lack of information about characteristic properties of a specific sludge/pollution combination is the main obstacle in the route from first ascertaining that a particular harbour subsoil is polluted, to final identification of the full scale treatment plant. In the first instance, information must be generated regarding the distribution of pollutants in relation to the distribution of the original geophysical components. Based on this information rational decisions can be made on separation at a particular cutpoint and what sequential techniques should be involved for a certain fraction. For this purpose a `fingerprint method' is presented especially developed for investigation of polluted soil and sediments. The heart of the fingerprint method is a series of sequential hydrocyclone separations, by which a series of products is generated. The objective of the fingerprint method is to select an optimised treatment procedure in which the pollutants are concentrated in as small a volume of material as possible, leaving the bulk of the material clean. The pollutants can then readily be destroyed or isolated from the environment. The philosophy and advantages of the fingerprint method are demonstrated for a harbour sludge containing heavy metals as main pollutants. Hydrocyclone separation combined with flotation of both the coarse and fine fraction resulted in reusable and dischargeable products. Flotation of the fraction of fines was carried out by means of an experimental flotation cyclone enabling the selective recovery of mineral particles with diameters less than 10 microns. The overall conclusion is that design and engineering of treatment flow schemes for polluted dredged materials is a tailor made activity based on rational decisions resulting from the fingerprint information.

Jan 1, 1993

By K A Plumb

New structural studies in the Walker Fault Zone of eastern Arnhem Land are integrated with basin-wide reconnaissance observations, made to refine models for the structural evolution of the McArthur Basin and provide new insights into the nature of metal logenetical ly important pre-inversion phases of the basin's evolution. At least five principal events may be identified during the Proterozoic: The Tawallah Group and equivalents were deposited throughout the McArthur Basin during an extensional event. Rifting of an incipient Batten Trough occurred at this time, in a terrain characterised by orthogonal, linked extensional faults. Uplift and erosion of the Tawallah Group accompanied continuing extension and was penecontemporaneous with continuing deposition of the overlying Parsons Range Group, within a precursor to the Walker Trough. Dt (of the Walker Fault Zone) relates to a new rifting event, penecontemporaneous with deposition of the McArthur Group and its equivalents in the Walker and Batten Troughs. This rifting accompanied dextral strike-slip faulting along northerly-trending bounding faults, as a result of northwesterly-directed oblique extension, leading to pull-apart basins. D2 inversion of the Batten and Walker Fault Zones pre-dates deposition of the Roper Group. In the proposed model WNW-ESE directed shortening (D2.), accompanied by folding and thrusting, and by local development of cleavage in the Walker Fault Zone, is seen to be followed by northerly-trending sinistral faulting (D2b), about a SE to ESE-directed compression. D3 is basin-wide and post-dates the Roper Group. It is characterised by conjugate faulting and folding about ENE to NE-directed compression. The latest Proterozoic event to be identified (D4) comprises widespread north-trending strike-slip dextral faulting of Roper Group, coupled with N-S directed thrusting across the Urapunga Fault Zone and Murphy Inlier This is accompanied by late dextral reactivation of NNW to NNE-trending faults in the Walker and Batten Fault Zones.

Jan 1, 1994

By C Bellia, A Maldonado, S Strong, H Baxter

This paper discusses the technical and cost benefits of alternative data collection techniques used to collect lithological information, obtain laboratory testing samples and perform in situ testing. A comparison between diamond coring and sonic coring techniques is made using data from a recent geotechnical investigation for a final pit slope cut-back. The impacts of the coring method on laboratory strength testing results, material character testing and, ultimately, the mass strength parameters and subsequent slope design adopted are compared. The sonic coring method was chosen out of necessity and enabled the collection of tube samples of a clay unit of interest as well as bulk samples for material character and geochemical testing. The sonic coring generated unexpected degradation of clastic units, while cohesive clay-dominated units were recovered well. The likelihood that disturbance due to the coring method would result in lower than expected triaxial strength results was recognised ahead of time, with surplus samples collected and single-stage triaxial strength testing undertaken. This testing compared favourably with historic three-stage testing, where sample degradation occurred during the later stages. Material character testing of fine-grained, clay-dominated units was comparable with historic diamond core testing, while grain size estimates for more clastic units tended to be finer than previous results. The use of sonic coring over non-cored methods enabled the collection of material texture data, geotechnical properties and a full suite of geochemical analyses. This provided a comprehensive understanding of the lithological and geotechnical character of the rock and soil mass. A high-confidence geotechnical model was developed. The end result was the development of a slope design that was more aggressive than was previously designed (5° steeper inter-ramp angle), which has proven to be appropriate to the conditions following excavation. Overall, sonic coring was a cost-effective means of obtaining additional geotechnical data for the site.CITATION:Baxter, H, Bellia, C, Maldonado, A and Strong, S, 2015. Case study assessing alternative data collection techniques and analysis methods to assist with geotechnical slope design, in Proceedings Iron Ore 2015, pp 419–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Binks

This paper presents a case study that describes the selection, development, engineering and construction of a process plant for the biological oxidative pre-treatment of a refractory pyrite-arsenopyrite gold ore flotation concentrate. Prefeasibility and feasibility study resource modeling, metallurgical testwork, and environmental and engineering studies are outlined. Options considered for oxidation of the ore, which examine cost, risk, operability, recovery, engineering and environmental aspects are compared, with particular reference to pressure and biological oxidation. The BIOX« biological oxidation process was selected as the preferred oxidation process and the flow sheet for this process is presented. Selection of the BOIX« process resulted in special requirements for the feed preparation circuit, residue treatment and disposal, materials of construction and engineering. Use of a biological process in ore treatment also introduces particular process and engineering risks the management of which are discussed.

Jan 1, 2004

The perennial challenge facing mining and minerals operators is to improve productivity, usually by a combination of cost reduction and performance improvement. In a typical production situation involving mining and processing activities, the standard approach has long been to seek improvements in each activity, effectively in isolation from each other. However, the realisation is growing that there is considerable potential to achieve really substantial productivity gains by much improved integration of mining and processing with the key being to consider what is best in the total sense. Some of the linkages between fragmentation in mining and downstream processing are considered in this paper. These linkages involve technical, operational and economic Considerations.

Jan 1, 1997

Fast Adsorption Phenomena at Air/Liquid Interfaces

Sep 13, 2010