Search Documents

By D J. Williams, M S. Zbik, A Shokouhi

There is a considerable difference in the particle size distribution (PSD) of clay mineral-rich coarse coal reject with variations in the test moisture state and the chemistry of the water used for testing. The coarse coal reject tested were collected from Jeebropilly Mine, located in the Ipswich Coalfields of south-eastern Queensland. Differences between the results of dry and wet sieving analysis indicate a significant breakdown of the clay mineral-rich coarse coal reject on wetting-up. Wet sieving caused a breakdown of the gravel-sized fraction to silt and clay size without significant breakdown to sand size. There is also a considerable variation in the results of hydrometer analyses of the clay mineral-rich coarse coal reject with variations in the chemistry of the water used, particularly at the fine end of the particle size range. The waters used included tap water, coal processing water and deionised water. In addition, the method of dispersion applied prior to hydrometer analysis can have a significant effect on the PSD of clay mineral-rich coarse coal reject, with boiling and sonic vibration causing the most breakdown of the clay particles. This paper describes the testing methodology used and the test results obtained, and attempts to explain the results in terms of clay mineralogy and water chemistry.CITATION:Shokouhi, A, Williams, D J and Zbik, M S, 2015. Influence of water on particle size distribution of clay mineral-rich coarse coal reject, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 239–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

For decades strip mining with discon tinuously operating 'draglines and shovels has been the most economical operation method in the shallow hard coal opencast mines of Aust- ralia, North-America and some other countries. Continuously operating equipment such as bucket chain excavators and bucket wheel excavators in combination with conveyor belt systems, conveyor bridges and stackers had been deve- loped in Germany; during the last 25 years this type of equipment has been further developed in order to allow a high degree of rationaliza= tion as to opencast mines in unconsolidated overburden in Germany, in many European couh- tries, in India and in Victoria. The differing compactness of the layers to be mined, the increasing mining depth, the adverse over- burden to coal ratio and geotechnical con- ditions account for the combined use of con- tinuously and discontinuously operating equip- ment and systems. This paper is to demonstrate some projects showing the combination of continuously and discontinuously operating equipment which aims at optimizing opencast mine operations. It will be reported on the following combinations: - combined use of bucket wheel excavator/

Jan 1, 1981

By Henley R, Harris L

High resolution airborne magnetic and radiometric data have been shown to optimize exploration for epithermal gold deposits in the vicinity of Charters Towers, northeastern Queensland. The radiometric data allow extrapolation of poorly outcropping geology to provide a cost-effective mapping technique, even at exploration scales (eg. 1:25,000). At a regional scale (eg. 1:100,000) the magnetic data reflect the regional tectonics and divide the area into domains for the application of different genetic models. For example: 1. the Ravenswood Batholith is characterized by multiple intrusions dating from Ordovician to Permian age. The polarity of the magnetic anomalies implies an age for the intrusions and indicates a deposit style for exploration. 2. extensional and wrench tectonics along the northern margin of the Drummond Basin are interpreted from the magnetic data and indicate favourable blocks for detailed exploration. Genetic exploration models may be tested in favourable environments by the recognition of geophysical signatures. These signatures reflect structural, lithological and alteration patterns arising from controls on ore deposits and can be applied at regional or detailed scales.

Jan 1, 1989

By O Aydan, R Ulusay

Blasting is the most commonly used excavation technique in mining and civil engineering applications. Blasting induces strong ground motions and fracturing of rock mass in rock excavations. Particularly, high ground motions may also induce some instability problems of rock mass and structures nearby. Furthermore, it may cause some environmental problems due to noise as well as vibrations of structures near the populated areas. Furthermore, flyrocks is another major issue for the safety of people and damage to machinery and equipments when blasting is employed. In this study, the authors explore the ways how to estimate the ground motions as a function of distance, amount of explosive, number of holes. The ground motions were measured by stand-alone accelerometers developed by the first author and some empirical relations are developed. The effect of ground motions on the instability issues of benches such as sliding, toppling and rockfalls were investigated. Furthermore, the flyrock issue is investigated and some empirical relations to estimate the maximum distance of flyrocks from the blasting relations are compared and discussed. CITATION:Aydan, O and Ulusay, R, 2018. The ground motions induced by blasting in open pit lignite mines and its environmental effects, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 142–151 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Manefield, G Bournival, S Ata

Asteroids contain an abundance of valuable resources such as: nickel, cobalt, gold, platinum and rhodium. Whilst the consumption of mineral resources on Earth continues to deplete, meteoroids have the potential to become a significant source of minerals. Even though the minerals content of asteroids may be relatively high, the valuable minerals are more likely to be only a small portion of the total ore present in the main body. The ores must, therefore, be processed to extract the metals of interest from the waste. Existing terrestrial technologies rely on manipulating the physical and chemical properties of minerals. The application of these techniques to asteroids processing, however, is not straightforward due to the presence of different conditions such as zero gravity and lack of water in space. This paper discusses potential separation and extraction techniques that can be used for processing of asteroids.CITATION:Ata, S, Bournival, G and Manefield, M, 2015. Resource recovery in space, in Proceedings Third International Future Mining Conference, pp 275–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

Management of Mining Wastes in European Union and Developments in Turkey

Sep 13, 2010

By Karlson R, Rispin M

Chemical admixtures are not commonly included in the variety of backfill mixes used in the mining industry. This may be attributed to several reasons including, but not limited to: the perceived high added cost, 2. the lack of awareness about their proper use, and 3. the lack of knowledge about their features and benefits. In the construction industry today, however, chemical admixtures are used in the majority of the concrete produced, enabling concrete to become a more cost-effective building material. They also enable construction crews to meet demands for year-round construction, quicker completion of construction projects, and improved concrete properties. The high demand for chemical admixtures in the construction industry has led to numerous innovations in admixture technology in recent years. Some of these chemical admixtures have been found to enhance the production, transport, placement, and in situ properties of backfill mixes. Others have been found to reduce the cost of such mixes while maintaining, and in some cases improving, their physical properties. In this paper, a few of such innovative admixture technologies are discussed. The benefits, imparted by these technologies to backfill mixes as well as performance data on their use in several backfill applications at various mines, are presented.

Jan 1, 1998

We outline a first version of an ambitious goal: The world's first horizontal (matrix-independent) generic sampling standard. The specific needs and requirements are overwhelming, as all the world's analytical standards follow strict matrix or material type classification pigeonholes, leading to a plethora of analytical standards. One could rightly expect a similar multiplication regarding sampling standards, yet the singular HORIZONTAL is aimed at being truly generic. Also the existing style of standards writing is cumbersome and partly contradictory. The current work is presently being pursued in CEN and European Union standardisation regimens, for which reason full disclosure and publication is not allowed. Respecting this constraint, we unofficially present selected key issues involved in developing HORIZONTAL: The objective and scope of a horizontal sampling standard is to delineate the minimum set of principles and procedures needed to guarantee documented representative sampling for all types of materials. The horizontal standard is designed for two types of use: 1. auditing/assessing/ improving the reliability of an existing sampling procedure, and 2. design and implementation of a new sampling procedure (new lot type). The principles in this standard are all derived from the Theory of Sampling (TOS), but the standard is far from a mere collection of TOS principles. Representativeness is a characteristic of the sampling process, not of samples themselves. For practical purposes, the horizontal standard follows the fundamental distinction between 'stationary lots' (0-D, 2-D, 3-D lots) and 'dynamic lots' (within TOS aka process sampling - including extended, non-moving 1-D lots). TOS' principles of 'correctness' must never be broken at any stage, lest representativeness is irretrievably lost. The horizontal standard is not written in the mandatory fashion for legally binding matrix-specific standards, eg ISO - for the present overarching purpose a different style had to be developed. The standard must be immediately understandable in full, which merits special demands, eg extensive use of didactic illustrations. HORIZONTAL introduces an all-inclusive sampling variability measure, Relative Sampling Variance (RSV) which is for sampling of stationary lots as variographics is for process sampling - RSV is to be used as a quality criterion for any stationary sampling procedure as applied to a specific heterogeneity (lot/material). The target for this standard is all individuals, companies, organisations and regulatory bodies who are responsible for sampling: technicians, process engineers, laboratory personal, academic and industrial scientists as well as project leaders, technical managers/directors and top managers. Based on current R&D we illustrate the principles promulgated by HORIZONTAL with cases from exploration and mining of minerals commodities, a Finnsh 'Autosampler' at work in the mining context (RSV) as well as sampling equipment for use in the cement and mineral commodities industries. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Mar 1, 2010

By K Esmaeili, S Aziznejad

Impact-induced rock fragmentation is a mechanism that is commonly used for rock breakage in drilling and crushing. Additionally, rock fragmentation by blasting is frequently used in rock excavation operations. Experience shows that the presence of discontinuities can significantly influence the impact-induced damage and fragmentation of rock. Quantification of the response of jointed rock masses to impact loads is complicated by the fact that the available laboratory tests are mainly designed for aggregates or intact rocks. It can be argued that neither of these tests adequately represent a jointed rock mass. This paper presents the results of a series of numerical simulations used to investigate the influence of pre-existing discontinuities on the impact-induced fragmentation of rock masses. The methodology includes determination of the static and dynamic mechanical properties of a rock unit by conducting a series of laboratory tests on intact rock samples collected from a quarry in Canada. A 2D distinct element code, Particle Flow Code, was used to generate a bonded particle model in order to simulate both static mechanical properties (uniaxial compressive strength, elastic modulus, Poisson’s ratio and indirect tensile strength) and dynamic mechanical property (drop weight tensile strength) of the intact rock. The calibrated numerical model was then used to construct large-scale synthetic rock mass samples by incorporating discontinuity networks of different intensity into the bonded particle model. Finally, the impact-induced fragmentation inflicted by a rigid projectile particle on the jointed rock mass samples, simulated by a synthetic rock mass model, was determined. More fragmentation was observed for the rock mass samples with higher joint intensity.CITATION:Aziznejad, S and Esmaeili, K, 2015. Effects of joint intensity on rock fragmentation by impact, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 377–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Cotnoir, Q Liu, D Richard, M Ourriban

The difficulty in fine particle flotation has been attributed, among other things, to a low bubble-particle collision efficiency. Many technologies have been developed which aim at increasing bubble-particle collision efficiency, either by generating micro bubbles or by enlarging particle sizes. However, commercial applications of these technologies are limited. Over the last five years COREM has been actively testing fine particle froth flotation technologies with the objective of commercialisation. Several fine particle flotation technologies, such as dissolved air flotation, electro-flotation, floc flotation, selective flocculation-flotation and carrier flotation, were tested on both single minerals and ore samples in order to identify the reasons that prevented these technologies from being used on a commercial scale. It was found that the two most noticeable factors that prevented the successful application of these technologies were: Mechanical entrainment of fine gangue minerals. This was a general problem in fine particle flotation, but was aggravated by these technologies that either generated micro bubbles or enlarged the sizes of hydrophobic particles. Oxidation of (sulfide) minerals that resulted in hydrophilic oxidation product coatings. The oxidised fine particles could not be recovered by these fine particle flotation technologies effectively. Solutions to the two problems, ie gangue entrainment and fine particle oxidation, were proposed and tested. It seems that polymeric depressants with both depression and flocculation functions could significantly reduce gangue entrainment, and hydrophilic surfaces of oxidised fine particles could be modified by high intensity conditioning or controlled sulfidisation, thus increasing the recoveries of fine valuable minerals. The improved fine valuable particle flotation and reduced fine gangue entrainment along with fine particle flotation technologies resulted in much improved flotation separation of fine particles.

Jan 1, 2005

By J O. Watson, V S. Vutukuri

This paper presents results of an investigation on acoustic emission characteristics of granite, sandstone and rock-like material in the unconfined compression and tensile tests. Both the acoustic emission signature and stress-stain curve are analysed in the experiments.The experimental results show that different acoustic emission characteristics are observed at different stress and deformation stages in unconfined compression and tensile testing. Extensive and unstable acoustic emission changes may be interpreted as indicating failure of the rock.

Jan 1, 1999

By S M. Gover

Estimating the probability of failure for embankments is not intuitive. It requires not only an appreciation of the strength of the embankment, but an understanding of the variability and uncertainty in the strength parameters as well. These additional aspects are, in themselves, relatively new to most practicing engineers, and therefore require some discussion.This paper discusses the concepts of probability and uncertainty, and presents a reliability-based numerical experiment, together with a literary study and collation of some of the author’s historical slope stability analyses, to investigate whether a direct relationship between safety factors and probabilities of failure exists for certain levels of uncertainty in strength parameters. In doing so, a useful tool is presented whereby knowing the safety factor of a simple slope or embankment with a consistent level of uncertainty, one can infer an approximate probability of failure.CITATION:Gover, S M, 2018. Linking safety factor to probability of failure, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 384–396 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Mutmansky J. M, Organiscak J, Qin J, Bhaskar R

The results of a two-year research study into the relationship between quartz dust levels in host material and in respirable dust in continuous mining sections are presented in this paper. The experimental design and sampling procedures for underground data collection are outlined. The sample analysis procedures for quartz determination, the analysis results and conclusions of the study are discussed.

Jan 1, 1988

By Davis RA, Wasp EJ, Cowper NT

The transportation of solids by pipeline is not new. In 1891 a United States patent broadly covering a method of pumping coal with water was granted to W. C. Andrews. His pilot plant was constructed on what is now the site of the New- York Public Library in Manhattan. His process was applied to pumping coal mine waste back into the worked out portion of coal mines. On October 26, 1967, the world's first long distance iron ore slurry line was put into service by Savage River Mines. The commissioning of this 5.0 million dollar installation climaxed three years of development, testing, and construction and proved the Company's faith in pioneering' this unique transportation method for iron ore. This paper will discuss some of the more pertinent items in connection with that three-year period. Also to be discussed will be the operation of this line during the past eleven months.

Jan 1, 1969

By C Mroczek, B Mitchell

Perilya Broken Hill, from its inception, has budgeted for more than 2.0 million tonnes per year from the Southern Operations. This tonnage was planned to come from in excess of 100 stopes per year in a remnant mining environment with numerous mined voids and consequent mining challenges. To mine an average of two stopes per week requires patience, flexibility and detailed knowledge to best manage the potential risks and hazards. The evolution of the Perilya Broken Hill Mine Planning Process has necessitated the establishment of a process to identify and manage these risks during the planning stage in a reliable but efficient manner. This process is to ensure that vital steps for each stope are not missed, and that each personÆs work can be tracked by other members of the team. This paper outlines the planning process from resource to stope closure.

Jan 1, 2005

By V S. Mutton, M J. Shearer

"The current economic challenges faced by the mining industry led to a review of options for reducing the cost of ventilation control devices (VCDs). The VCDs at the Mount Isa Mines site operated by Glencore in Queensland typically experienced significant damage on the operating levels and required expensive replacements. Ventilation controls can become damaged by the effects of stope firings. This paper discusses the nature of blast wave effects, giving consideration to distance from the firing and changes in mine geometry. The time taken to adjust the airflow on the operating levels with the current VCDs resulted in the loss of productivity opportunities. The mine site engaged an equipment supplier to collaborate on the development of a high-strength regulator to control the required airflows within its underground workings.The strengthened regulator proved to be cost-effective and provided additional benefits, including ease of use, simplicity of installation and speed of change in the control of available ventilating airflow. An added advantage of the re-engineered regulator compared to contemporary VCDs is its flexibility, which includes the ability to easily move mobile equipment into different ventilation districts where required without the need to remove the VCD from its location. This paper describes both the innovation and environmental sustainability approaches followed when developing the new regulator for its implementation at the site.CITATION:Shearer, M J and Mutton, V S, 2015. Advanced ventilation control – an analysis of innovation and environmental sustainability, in Proceedings The Australian Mine Ventilation Conference, pp 55–62 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

Part of a four-year course in metallurgy, dealing with metallurgical process engineering, was designed for students to acquire knowledge and skill from physical science, metallurgy, process engineering, and social science. Principles of education, and guidelines obtained from a study of professional practice, indicated that students may learn effectively through a planned sequence of problem-solving exercises based on the diverse functions of metallurgists in industry. The more important characteristics of the curriculum and a few illustrations of the problems are included. An outline is given of the current procedures used to develop parts of the curriculum, and of the students' diffic- ulties and achievements.

Jan 1, 1984

By Y Wei, P Soole

This paper gives a brief description of VirtuoBlast technology ù a new, automated and highly interactive stereo vision technology which has been developed in CSIRO Exploration and Mining. VirtuoBlast technology is an integration of three advanced technologies - close-range digital terrestrial photogrammetry, oblique stereo imaging or high-speed stereo imaging, and temporal-spatial image matching technique. VirtuoBlast has been developed for the automated 3D measurement of blasting through rapid collection, processing, analysis and visualisation of 3D data related to blasting. A major field trial has been undertaken in August 1998 at the KCGM super pit. The field trial involved three applications of the technology, namely, pre-blast 3D surface mapping; post-blast 3D performance measurement; and temporal-spatial modelling of dynamic blasting process. This paper presents some results from this trial with emphasis on the application of VirtuoBlast technology to pre-blast 3D surface mapping and post-blast 3D performance measurement. Application to the temporal-spatial 3D modelling of dynamic blasting process will be presented in a separate paper. Pre- and post-blast surface models derived using both VirtuoBlast technology and conventional field survey method are presented. The differences in results using the two mapping methods clearly show that the digital photogrammetric technique has many advantages over conventional survey methods. Results of pre- and post-blast from the field trial have demonstrated the potential of VirtuoBlast technology to efficiently perform pre-blast 3D surface mapping and post-blast 3D performance measurement of production blasts. Demonstrated applications of VirtuoBlast technology to automated 3D measurement of blasting are showing an exciting future in advancing blasting science and modern blast design. The basic technologies are in place, however, continued improvements to the functionality, robustness and outputs are needed. The challenge is to build on the current state-of-the-art, by developing techniques and hardware which can be easily transferred to and implemented by the mining community. Current and future research and development will see improvements in imaging systems, automatic image processing and 3D data analysis.

Jan 1, 1999

By E Villaescusa, C Drover

The stability of access tunnels is one of the main engineering challenges in deep underground mine construction. Many underground hard rock mining operations are now reaching depths where the induced stresses are such that sudden and violent failure of the excavations can occur very soon after construction. The loading conditions on the installed ground support schemes are often underestimated by conventional engineering design methods. Therefore, the actual loading conditions often exceed the installed ground support capacity. This can result in failure of the excavations and, in extreme cases, potentially closure of mining operations amounting to hundreds of millions of dollars in lost production. More frequently, violent excavation instability at great depth causes operational delays, costly and unplanned rehabilitation, as well as risks to worker safety. In order to address this challenge, this paper briefly summarises a modern, innovative approach to the design and construction of mine development at great depth. The process follows seven main steps. The first step is to characterise the rock mass strength, structure and stress. The second step is a stability assessment, which identifies the plausible modes of excavation failure, based on the rock mass characterisation. The third step is the definition of an excavation geometry which is harmonic to the high stress conditions. The fourth step is to prepare a site-specific face destressing drill and blast design which will reduce the potential for rock mass instability during the development construction cycle. The fifth step is to accurately quantify the expected loading conditions on the installed ground support. The method of doing so is uniquely analytical and probabilistic. It is based on the natural mechanical relationships between rock strength, structure, induced stress and the physical characteristics of the instability, including its mass and ejection velocity. The sixth step of the design process is to specify a ground support scheme arrangement with sufficient strength and displacement capacity to exceed the rock mass demand by a safe margin. The final stage is to install the complete ground support scheme using mechanised technologies which minimise the exposure of the equipment operators to unsupported ground at the tunnel face.

Nov 29, 2022