Search Documents

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

In setting out to describe the methods and machinery employed at Iron Knob the writer does not attempt to give any information as to the situation, topography or geological features of the locality. This, together with estimates of the quantities of ore still available, has been carried out in a most thorough manner by R. L. Jackr and F. R. Hockey. This essay is intended to deal with working methods as they exist to-day, beginning with drilling, blasting, quarry traction, etc., and touching on such details as the supplyof electricity, water and compressed air.At the present time almost the entire output of ore is won from the hill known as Iron Monarch. The form of the hill, a smooth, rounded dome, rising some 640 ft. above the plain and having a base diameter of n miles, lends itself ideally to the "bench" system of open-cut quarrying.Fig. 1 shows the relationship of the benches "A," "B" and "E" in their order of development. Bench "E" is at present the principal working, but, as the greater part of the ore above this level has now been removed, bench "A," some...

Jan 1, 1936

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By S K. Schwank

Trench cutter systems have been used in civil engineering for the least 30 years for the installation of deep cut-off walls, retaining walls and foundation systems. The systems are constantly advanced to achieve greater depth, penetrate through harder rocks a provide a bigger footprint of the cutter. The state-of-the-art equipment can reach down to 250 m vertical depth and penetrate all different types of soils and rocks up to 150 MPa unconfined compressive strength.In mining, especially in commodities with a high value and where the ore deposit has a small footprint, cutter mining with vertical attack from the existing ground level will be a new, cost-efficient approach where conventional open pit mining is not economically feasible due to a high stripping ratio. The same applies for open pit mines that have reached the end of their conventional mine life and where going underground is also uneconomical. The BAUER Cutter Mining System, which has been adapted to the special needs of mining, is a new technology that will allow mining at depths of up to 250 m.The same system can be also applied to ore dykes, be it vertical or slightly inclined, concentrating the excavation on the actual orebody and minimising the strip ratio and the contamination of ore. The system can be adapted to the dimension of the dykes or veins and to the rock conditions.BAUER’s latest approach is to use the vertical cutter mining technology for the extraction of sea floor massive sulfides from the seabed in deep ocean waters. Due to the compact footprint of the system and the vertical attack for mining, extraction of the ore can be concentrated on the hot spots, minimising the environmental impact on the sea floor both for mining and manoeuvring the remote-controlled mining tool.CITATION:Schwank, S K, 2015. Cutter mining – crossover technology from civil engineering to mining, in Proceedings Third International Future Mining Conference, pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

A brief history of the significant haulage truck feature changes and the factors that influenced those changes during the 60's and 70's provide a basis for forecasting the changes that can be expected in the 1980's. A review of the impact factors and changing requirements that currently exist that will create changes. Define the critical requirements of a successful haulage truck design and discuss the availability of bigger engines and better electric drive componetry to provide deeper pit capability and improve reliability. The Unit Rig Trolley Assist System to provide improved productivity and diesel fuel savings and an economic analysis to evaluate the Trolley System is covered. The Unit Rig Automatic Truck System for a driverless truck is covered in concept and discussed from the point of view of the experience in a test in a New Mexico mine. INTRODUCTION A good basis for trying to forecast what is going to happen in the future is to go back a little bit in history, to see what the influencing elements were in different periods of time as a foundation for the forecast. INFLUENTIAL FACTORS IN THE 1960'S If you look at the truck development that occurred in the 1960's, there were some identifiable factors that give us insight. (See Fig. 1) Several things happened at the beginning of the 1960's. Mechanical drive haulage trucks were introduced that were

Jan 1, 1982

By D E. Tennant

In the fields of geotechnical engineering and slope management, various software packages are used to assess the behaviour or propensity for a slope to fail. Traditional kinematic analysis calculates the probability of failure of design sectors with respect to dominant structural set orientations. A novel methodology is provided here to view potential hazardous slope behaviour in 3D, allowing engineers to make informed decisions regarding various pit slope geometries. Apparent dips are calculated for every point in space with respect to every slope orientation of the entire pit surface/design, specifically in reference to bench and inter-ramp planar failure mechanisms. Implementing a proactive approach to slope design will not only lead to early mitigation of risk but can also add direct value by enhancing or improving upon slope angles for earlier access to ore. From a safety perspective, identification of unfavourably oriented slope geometries can be dealt with before failure occurs. This methodology relies on a strong understanding of the existing rock mass anisotropy, particularly behind the face, thereby removing some of the uncertainty surrounding pit design as well as presenting engineers with an additional means to manage risk.

Nov 29, 2022

By T N. Little

The aim of any rock breaking activity is to achieve success by developing designs that are blasting objective-specific and geology-specific, and then implementing such designs. This paper targets mining geologists with the aim of extending their knowledge of the rock fragmentation processes and providing insights to the significant relationships between geology and blasting. There are two main relationships, and if mining geologists appreciate both these relationships, then they can play a key role in optimising production. The business risk continuum is introduced to support this understanding. The first relationship is between geology and potential blasting hazards, and the operational complexity required to manage those risks. The risks associated with eight different ground types are discussed in terms of ground conditions, hazards and controls. These types are: reactive ground, hot ground, geothermal ground, fibrous ground, cavernous ground, combustible ground, pyritic ground and conductive ground.The second relationship is between the bench geology and blasting results. The blasting results discussed include: muckpile characteristics, remaining rock faces and blasting emissions. In this regard, some detailed insights and graphical examples are given for the influence of geology on blasting emissions, in particular, vibration, airblast and flyrock.A detailed description of the geological materials themselves can convey much useful information for blasting operators provided they are able to utilise this knowledge. Geologists are ideally suited to provide this description more effectively if they are familiar with the blasting process and the rock mass properties that influence blasting hazards and blasting results. It is also important to have clear statements of blasting objectives and associated operational targets, and this will maximise the likelihood of achieving the desired outcomes. The main aim of the paper is to highlight that geology is currently not fully utilised in the blasting process. In this regard, geologists are often not entirely aware of the blasting process and how they can contribute. The two significant relationships discussed above are integral parts of this process, and thus they are discussed as separate issues in the main body of this investigation.

Aug 22, 2011

By J-T Zhu, Q-Y Tu, S-L Kong, L Wang, Y-P Cheng, H-Y Liu, Q-L Yang

China is the largest coal-producing country in the world, while the geological conditions of deep coal mining are extremely complicated with high ground stress, high gas pressure and low permeability, which results in the difficulty of gas drainage and aggravation of gas explosion and coal and gas outburst disasters. Co-extraction of coal and gas is an effective method to eliminate coalmine gas disasters and realise the safe exploitation of coal and efficient gas drainage at the same time. This concept is widely accepted by the main coal-producing countries around the world, while the concrete definition of co-extraction is vague and not unified, and there is little accurate theoretical support for co-extraction of coal and gas, which makes it hard to determine efficient gas drainage methods correspondingly according to the features of coal seams in a comprehensive and systematic way. Based on theoretical analysis, laboratory test and field observations, basic thoughts and specific definition of co-extraction of coal and gas were put forward after analysing the occurrence characteristics of coal seams in China. We obtained the mechanism of mining-enhanced permeability and established the corresponding theoretical model, which is the process of fracture network formation through opening recovery of the original fractures and new fractures produced by unloading damage. Based on the core idea of ‘mining-enhanced permeability’, engineering approaches of ‘unloading by boreholes drilling’ for the single coal seam and ‘unloading by protective seam mining’ for the coal seam group were proposed to realise safe and efficient co-extraction of coal and gas. Meanwhile, combined with engineering practice, we put forward the construction principle of coal exploitation and gas drainage system in different coal seam occurrence conditions. The above methods were applied successfully in the Tunlan coalmine in Shanxi Province and the Panyi coalmine in Anhui Province, which had established the ‘underground-surface united’ spatial gas drainage modes, and could ensure safe and efficient co-extraction of coal and gas in the outburst coalmines.CITATION:Cheng, Y-P, Wang, L, Liu, H-Y, Kong, S-L, Yang, Q-L, Zhu, J-T and Tu, Q-Y, 2015. Theory of safe and efficient co-extraction of coal and gas and its applications, in Proceedings The Australian Mine Ventilation Conference, pp 79–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By Griffin PT, Espinosa-Gomez R, Jameson GJ

Two major issues are to be addressed in the Copper Concentrator of Mount Isa Mines Limited. The first of these is the need to increase concentrator flotation capacity to increase copper recovery, while the second is the need to reduce the iron sulphide dilution to meet future smelting requirements. Extra capacity in the cleaner and retreatment sections of the concentrator have been identified as key target areas, with additional copper recovery of at least one per cent identified from plant trials. Extensive pilot plant tests have been undertaken to evaluate the performance of the Jameson cell compared to conventional mechanical cell and column circuits. This work has shown that Jameson cells present an opportunity to achieve the desired grade and capacity specifications at lower capital cost than available alternatives. This paper outlines metallurgical results of work undertaken in the Copper Concentrator, together with a summary of pertinent Jameson cell operating parameters investigated during the period.

Jan 1, 1993

The development and introduction of a preventive maintenance scheme in the coke ovens department, coal preparation section, of The Broken Hill Proprietary Co. Ltd., Newcastle steelworks, is described together with its operation and the results achieved during the first 12 months.'fhe scheme consists essentially of an engineering analysis of the plant to establish maintenance schedules, and to record the details on reference cards.Items are reviewed progressively and a weekly work schedule is prepared, from which work orders are passed on to the maintenance foremen. These foremen in turn originate action orders and issue inspection sheets as required. Results are then reported back to the maintenance planner and used to revise norms, practices, and cycles.INTRODUCTIONWhat is maintenance? Some people consider maintenance to be the work involved in putting things together again after they have fallen apart. The author regards it as the mechanical care and repair of plant machinery and equipment to keep it operating in sound mechanical condition, without undue interference with production processes.Maintenance may be organized or haphazard, and, too often, what has been fondly imagined to be nicely controlled and organized maintenance proves, under pressure, to be more correctly described as haphazard. Haphazard maintenance deals with breakdowns as they occur, and frequently finds itself confronted with more breakdowns than can be handled. Even organized maintenance, if not based on sound planning, can, at times, be found in a chaotic state, because of unexpected and unanticipated breakdown.Properly planned and scheduled maintenance permits an orderly and controlled approach to the problem of maintain...

Jan 1, 1961

By J R. Taylor, J A. Muchan, S M. Pape, B S. Davis

Acid and metalliferous drainage (AMD) is routinely derived from waste rock, tailings, pit wall rock, underground mine voids, heap leach pads, ore stockpiles, concentrate stockpiles and even slag piles. In many jurisdictions, there is an assumption that tailings materials represent the highest AMD risk. This is likely due to their highly sulfidic and ultra-fine grained nature, and the fact that they occur in large tonnage, partially unsaturated deposits. These characteristics are not unreasonably associated with reactive and therefore highly polluting mine waste materials. Interestingly, however, the high sulfide content and highly reactive nature of tailings achieves the rapid consumption of oxygen in tailings pore spaces. This oxygen depletion can limit or halt sulfide oxidation throughout much of the tailings pile. Oxygen can only be resupplied to the tailings via atmospheric exchange at the air-tailings interface. The grain size of most tailings materials limits this resupply to a diffusion related process that only affects the uppermost 100–2000 mm. Hence sulfide oxidation in tailings can be inherently self-limiting. Unfortunately, the same cannot be concluded for waste rock materials.Using a unique site assessment strategy that focuses on quantifying acidity fluxes from various domains at a mine site, it has become increasingly evident that sulfidic waste rock produces the majority (typically 60–80 per cent) of the soluble acid and metalliferous pollution at most active and decommissioned sulfide-bearing mine sites. Whether sulfidic waste rock is disposed in engineered above ground facilities, backfilled into pits or even underground voids, it remains the primary source of pollutants for decades to centuries.Conventional end-dumping waste rock practices result in angle-of-repose pathways for air and water, and these internal fabrics exacerbate sulfide oxidation (ie pollution generation) and discharge from waste rock materials. The primary aim of many cover systems is to retard the access of air and water to these conduits. Recent thinking is that more emphasis needs to be directed at strategic waste rock pile construction practices, and less reliance placed on thin soil cover systems to prevent AMD.Waste rock pile construction approaches that minimise porosity and permeability but raise the retained moisture content and enhance water residence times have the potential to lower sulfide oxidation rates and thereby improve water quality outcomes. For example, innovative base-up, layered and compacted (BULC) waste rock piles have the potential to avoid or minimise the generation of AMD, supersede the need for treatment and facilitate successful closure and relinquishment across the mining sector (Figure 1).CITATION:Taylor, J R, Pape, S M, Davis, B S and Muchan, J A, 2016. Waste rock pile construction to lower closure and relinquishment costs, in Proceedings Life-of-Mine 2016 Conference, pp 97–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

By T Sprague, D Pateman

"The Gosowong Gold Project is owned and operated by PT Nusa Halmahera Minerals (PT NHM), an Indonesian company 75 per cent owned by Newcrest. It is located on Halmahera Island, in the North Maluku Province of the Republic of Indonesia, approximately 2450 km north-east of the national capital, Jakarta (Newcrest, 2017).Kencana is one of two underground gold and silver mines at the Gosowong Operation where ground conditions vary from competent to very poor. Development headings occurring in poor rock mass conditions require high capacity ground support including long tendon cable bolts. Manual installation of cable bolts in these development headings has been a time consuming process due to borehole collapse, blockages requiring subsequent re-drilling and a minimum eight hour grout curing time interval. The installation of cable bolts including the setting, plating and tensioning can impact the critical path for development heading advance resulting in development cycle delays.A review was conducted by PT NHM on current industry practices for alternatives to manual cable bolting. PT NHM subsequently approached Minova to assist with the development and trialling of self drilling anchors (SDAs) installed using jumbos with a rapid setting pumpable resin, CARBOTHIXTM. A series of system development trials were conducted and a reliable bolting system was developed utilising the existing jumbo drilling fleet with minimal required modifications.The system developed was a ‘one pass’ bolting process to install and grout SDAs using a two component resin with a remote, mechanised system. Improvements achieved from the system include: eliminating hole closure issues and more immediate support in poor rock mass effectively reducing personnel exposure to poor ground conditions by removing the requirement to access the drive backs reducing grout set time with full installation times for 6 m SDAs averaging 25 min.The resin grouting system has now been successfully implemented to effectively manage areas of poor ground conditions and to accelerate advance rates in high priority headings.CITATION:Pateman, D and Sprague, T, 2017. Development and implementation of a long tendon bolting system utilising resin grouting technology, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 79–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By S Farrokhpay, M Zanin

Although it is well understood that in flotation collection zone and froth zone are deeply interconnected, and reagents (and in particular collectors and frothers) cannot be selected without considering their synergistic effect, this concept is rarely applied in plant practice. The feed mineralogy also has an important role in how particles and reagents interact in flotation, which is sometimes overlooked by operators. In this work, a combination of batch flotation tests and froth stability measurements was used to optimise the collector and frother scheme for the flotation of a copper ore. The methodology was applied to an Australian copper plant which was experiencing high variability in froth stability in the roughers when the feed ore mineralogy was changing. It was hypothesised that chalcopyrite in the feed in combination with isobutyl-xanthate had a destabilising effect on the froth phase under the reagents scheme used. Froth stability was restored if a shorter chain length, less hydrophobic, xanthate was employed. It is apparent that the hydrophobicity of adsorbed films at the solid/liquid/air interfaces has a critical role in enhancing or reducing froth stability. Unstable froth causes a reduction in copper recovery in spite of a high collection zone flotation rate. The case study suggests that collection zone and froth zone can rarely be optimised independently of each other. With the laboratory procedure adopted, a more suitable reagents scheme was determined to respond to changes in the feed mineralogy, avoiding fluctuations in plant performance due to unexpected froth instability.CITATION:Farrokhpay, S and Zanin, M, 2012. Synergic effect of collector and frother on froth stability and flotation recovery - An industrial case, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 145-150 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

Mining ventures are essentially risky businesses. Explorers and project developers (plus their investors and financiers) attempt to minimise the risks involved or at least manage them. Core considerations are the obvious technical and commercial risks, but the socio-political system and regulatory environment in which the project will operate can be more important. Successful mineral investments in a country depend upon obtaining realistic and reliable technical results in a country that provides certainty, to gain and maintain investor confidence in a project. Brief commentary is provided on the usefulness of professional accreditation and ethics plus other specific reporting codes (eg JORC/VALMIN Codes) in reducing risks by reinforcing high technical competence and reputable individual professional behaviour (particularly in the context of currently perceived high corruption levels in so many countries). These various risk components are reviewed, especially in a global context, to showcase New ZealandÆs current position. Successful projects are those which provide investors with credible and reliable optimal results in less volatile environments because investors/lenders hate uncertainty and surprises even more.

Jan 1, 2005

By L Tatnell, R Mackay, A Tolooiyan

The multi-reversal direct shear test (MRDS) method is commonly used to measure the residual shear strength of soils. However, when the standard direct shear (DS) apparatus is used, the MRDS method is prone to two major sources of error: load cap tilting and specimen loss. These two sources of error can cause erratic behaviour in the residual shear strength curve, making it difficult or even impossible to determine the correct residual shear strength value of the specimen being tested. This paper presents the results of new modifications to the standard DS apparatus that prevent load cap tilting and specimen loss. Consolidated drained testing was performed on highly-over consolidated cohesive soil samples from a Latrobe Valley open pit mine, with results obtained from the modified DS apparatus showing a great improvement in the residual shear strength profile compared to those obtained using the standard apparatus. Large numbers of reversals (up to 14) conducted on a single specimen in the modified DS apparatus showed no notable load cap tilting and no specimen loss occurred. The modifications are easily applied to the standard DS apparatus, and analysis and correction of the data are simple.CITATION:Tatnell, L, Tolooiyan, A and Mackay, R, 2014. Measurement of residual shear strength using a modified direct shear apparatus, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 425–434 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By S Hapugoda, J R. Manuel, M J. Peterson, A Poliakov, E Donskoi

The occurrence and deportment of manganese in a number of ferromanganese and Mn-bearing iron ore samples from supergene-upgraded deposits, as well as from magnetite banded iron formation (BIF) and magnetite skarn deposits, was characterised in order to provide a basis for improved understanding of the processing characteristics of different ore types and investigate the potential for development of a robust geometallurgical classification for Mn-oxide ores. An understanding of the Mn mineralogy in mixed Fe-Mn deposits is necessary to inform any attempt to separate the Fe and Mn during beneficiation and to understand and predict the behaviour of lump and fine ore products during processing.A suite of analytical techniques was utilised, including hand sorting of lump ore particles, optical microscopy, X-ray fluorescence (XRF)/inductively-coupled plasma mass spectrometry (ICP-MS) chemistry, X-ray diffraction (XRD), scanning electron microscopy (SEM)/electron probe microanalysis (EPMA) and gas and solid phase pycnometry, in order to elucidate manganese mineralogy, mineral chemistry and mineral textures. Manganomelane group minerals (eg cryptomelane, hollandite), pyrolusite and lithiophorite were the most common manganese oxides in the samples examined. From the microprobe work, there was evidence of probable substitution of Mn, as well as Al and Si, into the structures of goethite and hematite. Manganomelane minerals were often intimately associated with goethite, in particular, and a clarification of this association and the associated Si and Al impurities is fundamental for improved understanding of beneficiation and sintering behaviour of Mn-oxide ores. Due to the poor or very fine crystallinity of some supergene manganese deposits and of some Mn oxide minerals, in particular the extent of overlapping peaks and their variable mineral chemistry, XRD was a problematic technique to equivocally determine Mn mineralogy.For lower-grade, earthy, poorly microcrystalline ores the mineralogical and textural association between mixed Mn, Fe and Al (¦ Si) phases was also critical. The deportment and potential separation of these elements in these deposits, especially Al, was complex, as they were characterised by forms of æhydrousÆ cryptomelane with higher levels of Fe-Al-Si substitution, as well as intimate intergrowths of ochreous-earthy goethite (probably aluminous in part) with cryptomelane, lithiophorite and/or kaolinite.Trace amounts of alkali elements in ferromanganese deposits were considered likely to be preferentially structurally associated with Mn oxides, while lateritic deposits with significant amounts of lithiophorite could contain elevated levels of deleterious impurities; Co and Ni in particular.A combination of solid and gas phase pycnometry proved to be a useful technique for broadly discriminating hematitic, goethitic and mixed Mn oxide-goethite lump particles based upon differences in their envelope and apparent densities. Based upon these preliminary results and ongoing Raman spectroscopy work on manganese deposits sensu stricto, Raman spectroscopy is a technique considered to have promise during targeted research to better link the optical and compositional properties of ferromanganese ore particles. CT-scan (computed tomography scan) analysis could also be combined with Raman spectroscopy and pycnometry to link mineral composition, mineral texture, ore particle textures and particle porosity/permeability to the high-temperature processing behaviour of lump and fines products.CITATION:Peterson, M J, Hapugoda, S, Manuel, J R, Donskoi, E and Poliakov, A, 2013. Textural characterisation of manganese minerals to improve the geometallurgical characterisation of ferromanganese and iron ores, in Proceedings Iron Ore 2013 , pp 281-300 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022