Search Documents

By B P. Banerjee, S Raval

In the recent past there have been dramatic advancements in the development of remote sensing platforms (satellite, aircraft and unmanned aerial vehicles – UAVs) as well as sensor systems (multispectral, hyperspectral, thermal, light detection and ranging (LiDAR) and radar). However, selection of the appropriate remote sensing technique for a mining application is complex and requires scrutiny on multiple scales including spatial, temporal and imaging capabilities. This presentation highlights various conventional and emerging remote sensing approaches over a mine’s life.CITATION:Banerjee, B P and Raval, S, 2016. Applications of advanced remote sensing systems during a mine life, in Proceedings Life-of-Mine 2016 Conference , pp 116–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Smith N. S, Rholl S. A, Otterness R. E

The Bureau of Mines is conducting research to develop blast designs for the control of fragmentation and rock displacement and the reduction of overall mining costs. This Bureau experiment, a program of 25 reduced-scale blasts conducted at the University of Missouri-Rolla's experimental quarry, determined the effects on fragmentation of changes in burden, spacing, explosive diameter, and stemming-explosive length. Combined with previous work at this experimental quarry examining air gap, delay, and decoupling effects, this experiment provided a data base of over 50 shots. The fragmented rock, 1000 to 3000 kg from each 3- to 4-hole blast in the 1 m bench of massive dolomite, was completely screened to assess fragmentation. The explosive used for all the tests was extra dynamite initiated by seismic caps fired from a sequential blasting machine with delays of 5.2- to 13-ms/m of burden. Empirical equations were developed which predicted the effect of shot design parameters on the fragmentation. These formulas predicted the average fragment size of each of the 25-shots to within 13 percent. For spacing to burden ratios of 1, 1.4 and 2, there were optimum burden to explosive diameter ratios (B/de) of 30, 26 and 20, respectively. Decreasing the B/d. ratio beyond these levels resulted in little or no reduction in the average size. For B/de ratios above these levels the average size increased but, at least a 15 percent reduction in the average size results when the shot design parameters are optimized.

Jan 1, 1990

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

As we look back through the Proceedings of our Institute, we find few papers dealing directly with education and recruitment. Apart from papers prepared in the earlier decades of this century, there was little written discussion on the subject until the 1950s, and mostly this was by the professionals, the professors and lecturers who staff the various mining schools of Australia and New Zealand.I use the term "mining school" in its fullest and widest meaning, to cover all aspects from ore to metal, and not in the narrow meaning that the word might imply. At the same time, in restricting the parameters of this address to "ore to metal" I recognize that I am excluding the very important fields of physical metallurgy and materials science; this I do because there is a limit to the quantum of any paper, and in fact these subjects are more closely allied to the use rather than the production of metals.However, the lack of education papers does not mean that education has been regarded lightly by The Institute. Sir Maurice Mawby in his presidential address in 1968, reminded us of the original objectives of The Institute, one 'of which was, "To promote the arts and sciences connected with the economical production of the useful minerals and metals ...". Our present Royal Charter is more specific when it says that one of the objects of The Institute is, ". . . to encourage the study of engineering with special reference to mining and metallurgy ...". If we recognize that in itself membership of our Institute is one means of continuing our education, it is true that education has been a concern of The Institute since it was first founded.Occasionally in recent years, an intrepid president has ventured to tell the academics what the industry needs, and he generally does this in a "no-question" situation! However it is encouraging that those entrusted with mineral education have always accepted this; they keep coming back for more and ask us to tell them what we want, and they will provide it.In 1948 a considerable dialogue on education was initiated when a standing committee was established by the Council of The Institute. In the period 1949 to 1951, three papers were prepared under the chair...

Jan 1, 1974

By G Sparrow

The Murray Basin is being heralded as the next major mineral sands province in Australia. Already exploration programs have delineated extensive commercial deposits and several companies are progressing with plans to produce zircon, rutile and ilmenite in the Basin. As these deposits are developed consideration will need to be given to several key issues of the Murray Darling Basin; the availability of fresh water and management of salinity in the area being two of them. In this paper ideas being developed in CSIRO that link the processing of mineral sands with the salinity problem in the Basin are presented. The proposal presented here is to process saline water to produce industrial minerals with large volume applications and to produce value-added products from the mineral sands in the Basin using reagents produced from the saline waters. Processes to produce titania pigment and zirconia consume chlorine, caustic soda, soda ash and hydrochloric acid, all derivatives of salt (sodium chloride). There may be a good economic incentive if these processing plants were located in the close vicinity of each other.

Jan 1, 2001

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician 'slate belt' greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northernPaparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By S Hawker, M Gibbs, A Craven

Current climate change projections suggest both an increase in the intensity of significant rainfall events and an increase in the variability of rainfall in some regions of Australia. It is necessary for mine site owners and operators to understand the effects that this potential shift in climate may have on their operations. The ability to maintain compliance with discharge regulations and operational security for those sites that rely on surface water run-off harvesting may be negatively impacted if some current climate change projections are realised. Although current regulations require the preparation of water management plans, these are generally developed using historical climate records for the site in question and as such do not give any indication of a siteÆs resilience to the influences of climate change.This study compares design and operational considerations for a case study mine site using historical rainfall records and modified records representing climate change projections. The future climate models are invariably broad scale and are limited in their capacity to be downscaled to a reasonable resolution for developing a site water balance. Instead the local historical data set has been modified to concentrate precipitation to peak periods and propagated through the model. The study looks at the siteÆs response to the potential changes in climate.It is shown that if current climate change projections are realised, this will have a significant effect on both the necessary size of designed surface water infrastructure and operational considerations on-site. A discussion is presented on the potential risks that climate change presents to mine sites and the range of options that could be considered to mitigate these risks. Depending on a number of factors, including location and risk profile of the owner/operator, resilience to climate change can be addressed as either a capital or operational expenditure (CAPEX/OPEX).CITATION:Craven, A, Hawker, S and Gibbs, M, 2013. Site water balance response to variable climatic conditions, in Proceedings Water in Mining 2013 , pp 211-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By P J. Scales, D Boger

Technological advancements in mineral processing have increased the feasibility of refining low-grade ores. Because of this progression and continual depletion of high-grade ore deposits, much larger volumes of waste material are produced. At the same time, increasing environmental legislation and cost competitiveness dictate that these wastes be disposed of in a manner that is both environmentally acceptable and economically viable. To achieve these criteria, many mineral processing industries are dewatering waste streams in order to reduce the volume of tailings and increase water and reagent recovery. The subsequent dry disposal of these highly concentrated mineral tailings requires a thorough understanding of the effects of dewatering on the flow characteristics. Dry disposal represents a paradigm shift in engineering. The tailings are engineered to suit the disposal requirements, as opposed to engineering a facility to accommodate the tailings. It is therefore important to understand how the material properties and operational parameters can be modified to produce the desired tailings flow and deposition characteristics. As concentrated suspensions usually exhibit non-Newtonian behaviour, determination of the disposal plant operating conditions requires a thorough understanding of the rheological characteristics of the material. The implementation and optimisation of dry disposal methods involves three concurrent and interdependent rheological studies to determine:the concentration required to achieve the optimum spreading and drying characteristics of the tailings once deposited; the optimum conditions for pipeline transport; and the feasibility of dewatering the slurry to the required concentration. The paper presents an overview of the issues pertinent to management of the flow properties and processing of dewatered waste streams.

Jan 1, 2002

By M Flis

The Razorback Iron Ore Project is a high tonnage, low-grade magnetite deposit that defines a new iron ore district in South Australia. Known since the 1960s, the deposit has come into its own as the iron hungry world demands not only larger tonnages, but higher grade and cleaner magnetite concentrate ores that counterbalance the increasingly dirty haematite ores that are coming into production.Razorback is hosted by the Neoproterozoic Braemar Iron Formation, a tillitic unit that is part of the Adelaidean Geosyncline sedimentary sequence. At Razorback, this formation forms the southern limb of the Pualco Syncline, dipping at 42° to the north and outcropping along a prominent ridge. The formation consists of a series of alternating bedded tillitic and interbedded magnetite units that represent cycles of glacial advances and retreats. Seven cycles, resulting in seven stratigraphic members, are recognised. Members B, D, and G are the thickest, at 30 - 70 m each, and are the target of current investigations. While the bedded magnetite has the highest iron content, typically 35 per cent Fe, the tillitic unit, at typically 26 per cent Fe, has similar iron content in the ground mass but is diluted by the inclusion of iron-poor granite and metasedimentary dropstones. The mineralisation forms a simple dipping tabular body with only minor faulting, folding and intrusives. Grades, thickness, dip, and outcropping geometry remain very consistent over kilometres of strike, presenting an excellent mining proposition.Razorback differentiates itself from other Australian magnetite projects in a number of important ways. It is not a banded iron formation (BIF); it will have low crushing and grinding costs; and it is located in an infrastructure-rich area close to open-access, high capacity rail, to a selection of ports and to gas, electricity, labour and engineering services. Royal Resources has announced an Inferred resource of 277 Mt @ 25.9 per cent Fe. The company is targeting a resource of 500 - 1000 Mt to support a 10 Mt per year concentrate production. Davis Tube Recovery work shows that the ore is capable of producing a concentrate of over 68 per cent Fe with very low deleterious elements. Metallurgical testing confi rms the ore is soft, and with near-zero initial stripping ratio the project will have a low opex. With access to existing critical infrastructure, capex will also be low, ensuring Razorback will be a highly competitive iron producer in this emergent mining district.

Jul 11, 2011

By D R. Chalmers

Coal dust explosions have occurred in coal mines across the world. The Mitsui Miike Coal Mine disaster in 1963 was an example of how this hazard was not managed effectively, resulting in the loss of 458 lives and hundreds of people sustaining permanent brain injury from carbon monoxide poisoning. Management of the risks for this hazard have been well documented and have been implemented in modern coal mines. A recent trend in some mines has seen the abolition of barriers on roadways on the basis that the risks are being managed by the current controls. These controls include stone dust application, trickle dusters, dust analysis and dust removal. This paper explores the science behind such controls and questions the need for barrier protection on belt roads.CITATION:Chalmers, D R, 2013. Cybulski revisited - Lessons on dust, in Proceedings The Australian Mine Ventilation Conference , pp 165-168 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By S Lowjun, I Verster, C A. Thomas, E Forbes, K Runge, G V. Franks

Fine (<20 µm) valuable mineral particles are difficult to recover in conventional flotation circuits. (Trahar and Warren, 1976; Jameson, Nguyen and Ata, 2007; Kohmuench et al, 2018). This leads to a loss of valuable fine mineral particles to tailings. Recovering these particles would be of economic benefit. Novel reagents, including temperature responsive polymers, for example, are being developed to improve recovery of fine valuable mineral particles by froth flotation (Ng et al, 2018a, 2018b). The approach involves selectively aggregating the valuable fine particles and making these aggregates hydrophobic, resulting in hydrophobic aggregates of appropriate size (in order of 100 microns) being amenable to recovery by froth flotation. The polymers developed have been produced at laboratory scale but not a full scale yet. The exact cost of producing such novel polymers is currently unknown, but they are likely to be more expensive than conventional reagents.

Aug 24, 2022

By Coombes J, Richards W. L

The objective of this paper is to illustrate, in a practical way, how both geologists and mining engineers can use conditional simulation to add value to their decisions. Inherent assumptions, requirements and essential components of condition

Jan 1, 1998

By i, A Shirbazo, S Saydam, S Ata, H L. Ram, B Li

The integration of internet technology into industrial sectors has significantly accelerated the adoption of Internet of Things (IoT) devices, transforming communication, data aggregation, and information distribution. The mining industry has embraced this evolution by deploying IoT devices and advanced technologies like autonomous robots and sensors to enhance operational safety. These sensors enable real-time data transmission and continuous monitoring of key parameters, providing decision-makers with timely insights. However, the interconnected nature of these devices has introduced complexities, resulting in inconsistencies across operations. Addressing these challenges, this research explores the application of modern digital principles to the mining industry through the Reference Architecture Model Industry 4.0 (RAMI 4.0). RAMI 4.0 offers a robust framework that integrates digital and physical systems, promoting data transparency, interoperability, and decentralised decision-making. This study aims to briefly introduced framework designed for the unique challenges of mining operations, leveraging the latest digital technologies. The lack of standardisation in the mining sector highlights the need for a comprehensive approach to tackle issues such as interoperability, scalability, security, safety, and repeatability. Establishing standard procedures can ensure smooth interaction between connected devices, ultimately enhancing operational efficiency in the growing IoT ecosystem within the mining industry. Introducing a well-defined reference architecture like RAMI 4.0 can streamline management processes and improve operational efficiency in mining. By adopting this framework, the mining industry can effectively navigate the challenges of digital transformation, leading to a more connected and resilient future. The study concludes that RAMI 4.0, with its structured approach, can significantly enhance the efficiency and productivity of mineral processing operations, fostering sustainable growth in a digitally driven industrial landscape.

Sep 1, 2024

By S Warden, T Neville, P Leckie

At its simplest, the classification and characterisation of an orebody is a matter of Where, What and When. Where and with what spatial resolution are measurements taken, What properties are measured, and When are the data acquired, processed, and delivered to create the most value. This paper delves into how existing and near-term advances in measurement technologies, field automation, and whole-system-digitisation are combining to open new routes for mine and exploration productivity improvement. Commencing when the initial exploration hole is dug, the advancement in deployment of survey technology—from expert-operated, to driller-operated, to driller-integrated—is used to demonstrate a template for adoption of higher technology measurements. We then introduce and discuss the multi-use measurement as offering outsized returns from a single measurement run, highlighting two new technologies that acquire rock strength while drilling and downhole assay data as examples. For rock strength, we highlight a novel approach to determining Uniaxial Compressive Strength (UCS) while drilling, its relationship to and advantages over Mechanical Specific Energy (MSE), and how it offers utility to multiple downstream processes. For downhole assay, we detail how a back-tophysics approach to Pulsed Fast and Thermal Neutron Activation (PFTNA) analysis offers significant advantages over other measurement methods and earlier implementations of PFTNA, generating a rich data set that can significantly extend and improve the information on which mining decisions are made. Finally, we discuss the possibilities enabled via optimising data delivery, collection, and curation— noting a fundamental limitation of historical systems and exploring the possibilities that will be unlocked by soon-to-market solutions that better enable Orebody Characterisation data to (virtually) move in space and time with rock material post-blasting. Ultimately, the value of optimising the Where, What, and When from point of measurement to the moment it generates maximum value will create greater life-of-asset production for a lower cost and energy input.

Sep 1, 2024

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007

Traditional in situ fan flow test methods under accepted standards require determinations to be made of both static pressures and total pressures during testing. This is to determine the resultant velocity pressures, which are vital in the accurate determination of the final fan airflow. These crucial velocity pressure (Vp) determinations are normally determined using simple manometric instrumentation such as an electronic manometer or an inclined liquid filled manometer. There is relatively little noise or fluctuation in the static pressure determinations and they can be quite easily and accurately recorded. There is almost always considerable fluctuation in the velocity pressure determinations though due to the highly turbulent and irregular velocity profile normally found in such in situ installations. This velocity turbulence means that the recording of such data is subject to random human error as the observer tries to average such fluctuations mentally during the observation period. Worse than this, and in the extreme, the recording of such velocity pressure data could actually easily be misreported if, for some reason, persons chose to do so.The author has devised a field method using highly accurate quartz crystal logging barometers to objectively record these velocity pressures. The method eliminates the ability to either mistakenly or intentionally misreport these crucial velocity pressures and is carried out in parallel with the recognised methodology, so result comparisons can be drawn. As such, a far greater level of confidence can be achieved in the final flow performance results than using the traditional more subjective method. Further to this it is difficult and almost impossible to refute the results using this ancillary substantiation method.The accurate determination of fan flows due to the impost of the carbon tax has taken on much more significance given the financial impacts in Australia at this time. The methodology detailed herein can be applied equally for both fan flow compliance testing and the verification of mine airflow data for greenhouse gas emission evaluations.The paper utilises the results of one 24-point pitot traverse to demonstrate the various findings. These include the very wide range of velocity pressures, which were logged at most of the measuring stations. It also illustrates how the method is utilised and compares the results derived from both this method and the more subjective traditional method along with the benefits of logging the velocity pressure results during the testing process.CITATION:Rowland, J A, 2013. Removing some subjectivity from traditional BS 848 and ISO 5802 in situ fan flow tests, in Proceedings The Australian Mine Ventilation Conference , pp 155-162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Goddard

An alternative stoping method has been adopted for narrow vein stoping at the Tasmania Mine in Northern Tasmania. Colloquially described as ‘Radial-in-Reef’ (RiR) stoping, the method employs the drilling of radial rings in the plane of the Reef from a drill stub located at the geographic centre of the proposed stope panel.Production from the Western Zone of the Tasmania Reef has been undertaken remotely from the Reef since 2007, after a detailed geotechnical engineering analysis indicated that the integrity of the sill drives could not guarantee an acceptable level of confidence should an anticipated seismic event occur within a radius of 10 m. The key tenet of the remote mining approach was the exclusion of personnel from sill drives once stoping had commenced. The remote mining method had to be ‘retrofitted’ to four existing stoping blocks totalling 11 sill drives which totalled 160 m vertically. The remote mining method proved to be complex, cumbersome and very expensive. However, the ore was extracted successfully.By early 2010, previously developed ore had largely been exhausted and the future development with an orebody open at depth presented the opportunity to review the current extraction method. However, the new extraction method needed to maintain the tenet of excluding personnel from sill drives of active stoping blocks, but seek opportunities to reduce the difficult and costly aspects of the previous method. The new ‘Radial-in-Reef’ stoping reduced the development requirement from six to two drives per ore block. Cost implications aside, the significant reduction in prestoping extraction ratio was expected to also reduce the likelihood of seismicity. Transverse production rings were designed to be drilled radially from a drill stub mined from a mid-stope footwall drive. Stopes totalling up to 7000 tonnes were planned be fired in a single electronic blast. Extraction was designed to take place from a basal sill drive under teleremote operation. At the time of writing, the method was under trial.

Mar 21, 2011

By T R. Justice

The Eastern Distributor tunnel is located approximately 24 m beneath the suburbs of Woolloomooloo and Darlinghurst to the east of the central business district of Sydney. The 1.7 km long tunnel will carry three lanes of northbound traffic over three lanes of southbound traffic in a æpiggybackÆ arrangement, with a maximum cross-section 22 m wide by 12 m high.The tunnel is constructed predominantly within horizontally bedded Hawkesbury Sandstone. In the unweathered to slightly weathered state, the rock is typically medium strength (average UCS about 24 MPa), with an average quartz content of 72 per cent.Major geological features that intercept the tunnel route are the Woolloomooloo Fault Zone and two extremely to moderately weathered dolerite dykes. The fault zone intersects the tunnel at about 25¦ to its alignment and comprises a series of discrete faults over a width of approximately 50 m. The overall movement of the fault zone appears to be reverse. The two dykes are the 1 m wide Oxford St Dyke and the 6 m wide Great Sydney Dyke.This paper outlines the site investigations and the interpreted geotechnical model for the tunnel route prior to the commencement of tunnelling. This model is then compared to the encountered conditions. The very good correlation between the expected and the encountered conditions shows the high quality of geotechnical investigation and interpretation.

Jan 1, 1999