Search Documents

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Bettison, R Wright, N Taylor

The primary mine planning focus during early study phases of future mining projects is Life of Asset ore production and grade quality, this will always be the situation. While waste schedule optimisation is generally considered in the latter study phases nearing execution for a limited number of schedule periods only and not a true optimisation considering all attributes such as waste destination location, design, cycle time and closure. This can be particularly applicable in large multi-pit bulk mining operations where one approach to meet Life of Asset ore tonnes and grade targets has been to maintain pit development flexibility resulting in large open pit areas and substantial expit Overburden Storage Area (OSA). The value opportunity is to develop a Life of Asset waste schedule source-to-destination optimisation prior to mine development considering all applicable attributes and routinely review throughout the Life of Asset taking account of improved ore and waste knowledge.CITATION:Taylor, N, Wright, R and Bettison, M, 2018. Utilising mine planning to deliver closure landforms through productive movement, in Proceedings Life-of-Mine 2018, pp 96–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A J. Morrison, M Yahyaei, J S. Siong, J Wang, K Runge

The flotation cells used to upgrade ultrafine metallurgical coal (-250 µm) are usually poorly controlled leading to unnecessary loss of combustibles from the flotation system. This is mainly because coal flotation cells are typically controlled for process stability rather than optimisation of flotation performance. This is especially true for a flotation device commonly used in coal applications in Australia – the Jameson Cell. This then provides an opportunity to improve the flotation performance by shifting from a stabilising control strategy to a proactive optimising control strategy. For an optimising control strategy, the control system will require a means of relating and then measuring in real-time, the effect of changing operating conditions on the coal flotation performance. Hence, the major aim of this work is to propose a possible model-informed process control strategy that could be used for real-time performance optimisation. In this study, industrial site work was conducted on an industrial-scaled Jameson Cell at a Coal Handling and Preparation Plant (CHPP) in Central Queensland, Australia where superficial gas velocity was controlled to six different levels. At the same time, other process variables such as froth depth and flotation feed properties were measured. The empirical models developed from this study suggested that combustible recovery is a function of superficial gas velocity, froth depth, feed solid content and feed ash content and that a peak in combustible recovery existed as a function of superficial gas velocity. This led to the development of a model-informed control strategy that aimed to maximise the combustible recovery by determining and then operating the cell at the superficial gas velocity at which the peak occurs. This peak superficial gas velocity was found to be only a function of feed solid content. Based on these findings it would seem possible to operate a Jameson cell at peak performance by online measurement of feed solid content, prediction of the optimum superficial gas velocity and stabilising control to maintain operation at that superficial gas velocity set point. The development of this modelinformed control strategy can serve as a basis for the development of a more sophisticated modelpredictive control (MPC) system. However, more work will need to be done to improve the predictivity of the combustible recovery model by measuring and modelling performance over a wider range of operating conditions.

Aug 24, 2022

By Kato T, Eguchi M, Seino T, Itagaki K, Kimura T, Muto T, Shimizu T, Kobayashi T

Behaviour of minor elements in the dust collecting system connected with fluidized bed roaster for zinc concentrate was investigated by use of the bench scale experimental appara- tus. The dust collecting system was consisting of two dust chambers, hot electrostatic precip- itator, washing tower, mist electrostatic pre- cipitator, drying tower, absorption towers and potassium permanganate solution towers. Some volatile elements such as lead, cadmium and arsenic tend to concentrate in the fine calcine obtained in hot electrostatic precipitator especially in the case of the roasting with insufficient air supply. Special attention was paid to behaviour of mercury. In the roasting tests for plain zinc concentrate, it was considered that most mercury volatilizes at first as elemental vapour in the roaster, but with decrease in temperature of gas around a half of mercury forms compound, and both elemen- tal and compound forms of mercury were found in the gas stream. Elemental mercury is of course difficult to be trapped in the dust collecting system. To promote the compound formations, some additives for concentrate, such as selenium and halogens were effective, especially selenium of a few times equivalent to form HgSe repre- sented complete conversion of mercury from elemental to compound. To clarify the behaviour and removal mech- anism of mercury, various small scale laboratory tests were also carried out. It was confirmed that mercury sulfate formation is possible if temperature and flow rate are adjusted adequate- ly for gas stream consisting of 02-SO2-N2. To trap elemental mercury, various substances were tested, and excellent results were obtained with selenium. Satisfactory results were obtained with a selenium disc heated at 100 to 200¦C in a mercury containing gas stream. Also, applica- bility of scrubbing method with SeO2 solution was investigated, and the solution containing a few hundred ppm SeO2, 0.01 per cent additive and 6 per cent H2SO4 proved to be satisfactory.

Jan 1, 1980

By C C. Souza, S C. Amarante, A C. Arauj

All major companies now producing iron ore in Brazil currently employ or are planning to employ some sort of concentration method to upgrade their fine sized products (sinter feed fines and pellet feed fines). The criteria for the selection of the most suitable concentration method for each application include a series of parameters; the most important among them being related to ore mineralogy. This paper reviews the concentration operations currently employed in Brazil and shows how ore mineralogy plays a fundamental role in the selection of a given method. Examples involving gravity concentration (jigs and spirals), magnetic separation (Rare Earth wet drums, ferrous wheel, and Jones type magnetic separators) and flotation (especially column flotation) are discussed. Fundamentally important for the selection of a concentration method is the mineralogy of iron-bearing minerals and gangue minerals presented to the feed to the concentration unit operation. For instance, the presence of liberated quartz as the major gangue mineral for a pellet feed size stream generally indicates that flotation will be the best selection for the concentration of that stream. However, even if magnetite is present only in the form of crystal relicts within hematite grains, it may lead to the selection of either magnetic separation alone or a combination of magnetic separation and flotation for concentrating such material. Presence of gibbsite and/or kaolinite as the major phase containing alumina will also affect the selection of the concentration method in all cases. Again for the case of pellet feed size streams, kaolinite does not interfere with flotation whereas gibbsite tends to contaminate flotation concentrate (pellet feed fines) as it is depressed together with iron oxides and hydroxides during the reverse cationic flotation process.

Jan 1, 2002

By L Abrahamsson

The aim with this paper is to discuss experiences from the ongoing research project ‘Attract: A roadmap to attractive, inclusive, and safe mining workplaces’. The project’s aim is to analyse possibilities, effects, and consequences of the green and digital transformation in the Swedish mining industry from workplace, socio-technical and gender equality perspectives. The research project (2022–2025) at Human Work Science at Luleå University of Technology is financed by the strategic innovation program Swedish Mining Innovation (a joint venture by the national research funds Vinnova, Formas and the Swedish Energy Agency). The project includes a multidisciplinary research group of five senior researchers and five PhDstudents and a broad repertoire of methods, eg literature reviews, qualitative interviews with both managers and workers, workplace observations, workshops, surveys, and project seminars where the researchers and the company representatives together analyse the results. One important part of the project is the applied approach where the researchers work together with two mining companies and one subcontractor company. The project has two parallel main subprojects.

Sep 1, 2024

By M S. Powell

In this paper it is argued that we are entering a new mining era, based on considerably more challenging orebodies as we rapidly expand minerals production by exploiting previously uneconomic deposits. Rapidly increasing production costs cannot be sustained by continually increasing commodity prices, as illustrated by the recent downturn in the industry.Driven by reduction in grade, requiring the processing of 50 to 100 per cent more ore to recover the same amount of metal, often accompanied by finer grain structure - necessitating a finer product size and more challenging recovery - the productivity of the mining industry is dropping in real terms. The author suggests that tweaking current technologies and relying on economies of scale will not turn the industry around, but rather a switch to considerably more efficient processing is required.It is imperative to utilise the properties of the orebody, especially in terms of variability, in revolutionising our processing techniques. Our new mantra may be æselective mass mining with flexible processingÆ. This paper explores how this may be implemented using current technology and equipment in order to change the cost profile of the new mining industry. Orebody knowledge, based on the underlying process drivers, rather than proxies, is required. These properties and their variability will need to be propagated into the orebody through utilising the geological data rather than smoothing block averages, which destroys information on variability.Novel flexible circuit designs are presented that can respond to a wide variability in ore properties and throughput requirements in order to slash processing costs and energy utilisation, while enhancing overall recovery. The success of these circuits will be based on an ability to predict at both design stage and in everyday processing the variable ore properties, which is dependent upon reliable orebody knowledge that caries variability and underlying processing properties.CITATION:Powell, M S, 2013. Utilising orebody knowledge to improve comminution circuit design and energy utilisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 27-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A D. Campbell

The sublevel caving (SLC) mining method is becoming more widely adopted as an underground mining method as mines become deeper and target lower grade mineralisation. SLC has been successfully adopted in increasingly complex and wide-ranging conditions in the past 10–20 years, demonstrating the flexibility of the method. Various challenges encountered at SLC mines around the world have led to significant differences in operating practices, mine performance and mine productivity. Unfortunately, aspects related to productivity, operational performance and best practice are not widely published and remain with individual companies. Limited information is publicly available to compare operational performance of SLC mines in the various conditions where the mining method is now being applied. To overcome this shortcoming, a global review of SLC operations was undertaken over a three-year period as part of the Cave Mining 2040 research consortium. The purpose of the review was to document technical and operational practices, hazard management strategies and key benchmarking metrics at SLC mines around the world. A total of 21 mines spread over four continents and 17 different mining companies were included in the project. The main outcome of the project was a manual of operational and technical practices, benchmarking of key metrics and documentation of the current state-of-the-art for each aspect of SLC mining. This paper describes the main findings from the benchmark in terms of mine productivity, including mine development, production and mining costs. The implications of mine scale, depth and ground conditions on operational performance at each of the benchmarked mines is described and charts are provided comparing key productivity metrics.

Mar 29, 2023

By D Roughsedge, J van der Sandt, L van den Berg

Axial flow fans are commonly used as auxiliary fans in underground mines to supply air to development headings. As diesel dilution requirements increase the fans used in conjunction with ventilation bags are becoming larger in diameter to move greater quantities of air over greater development distances. It is not uncommon for mining operations to sometimes use a number of these larger auxiliary fans with high airflow capacity in parallel as primary fans for the operations. These primary fan stations are often considered temporary installations and the fan selection and fan station design is rarely optimised. These temporary installations may become permanent resulting in an inefficient or unreliable primary ventilation system. A recent study looked at the likely causes of multiple primary fan failures at one operation with axial fans installed as primary units where the fan selection and fan station aerodynamic design was far from optimal. This paper explores some of the typical mechanisms of failure such as high pressure stall, unbalanced airflow, and fan tip speed as well as fabrication material. The paper proposes a number of good practise principles that should be considered during the design of a fan station. A second topic covered is the advantages and disadvantages of using different types of fans such as axial, mixed flow and centrifugal units. Here the concept of fan specific speed and its relevance to fan selection is discussed. Finally the paper quantifies the effect of using a high pressure auxiliary fan as a primary fan in a low pressure circuit, which may increase the mineÆs operation cost.CITATION:van der Sandt, J, van den Berg, L and Roughsedge, D, 2013. Practical considerations when using auxiliary axial flow fans as a primary mine fan, in Proceedings The Australian Mine Ventilation Conference , pp 63-70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By F Phillips, E Deucker, J Kato

It is challenging to determine the optimal mining strategy to maximise value when a mine plan includes mineralised material which does not meet the full cost of mining but has value exceeding the variable cost of mining (‘marginal material’). Mining too much marginal material dilutes the operation’s head grade and undermines profitability. Conversely, leaving too much metal behind fails to achieve the full value of the endowment. Finding the balance between the two will maximise value delivered from the asset. This dilemma has traditionally been approached by calculating a suite of cut-off grades to define the grade of material that meets economic targets for an orebody (or zone within) and should therefore be included in the mine plan. A problem with this approach is that individual mining blocks within the zone have different costs, value and confidence levels, with each having economic co-dependencies between them. Blocks of identical grade but different mining contexts will have distinctly different economic outcomes. For example: • a block may be a low-grade increment or shell around a higher-grade stope; • a block may be available to be mined when there is spare mining capacity; or • a block may defer access to significantly higher cash flow material. Each of these circumstances would result in different value from the blocks if included as part of the mine plan. Cut-off grades calculated as averages over zones of material, or in isolation from schedule-based information, are missing the entire mining context that determines the ultimate economic outcome of making a mining decision. There are tools and techniques available to address this for open pit mining, however underground mining has different nuances. There are more intricate economic and physical dependencies between potential ore blocks, and importantly, the decision to leave material in situ can be made at any time. The case study in this paper explores a new methodology for underground mining, targeted towards strategic planning applications. It examines whether the economic logic usually applied via cut-off calculations can be implemented in the schedule so that optimal economic decisions can be made on a block-by-block basis, taking into account the mining context of the block, with the objective to maximise asset value. The results of the case study scenarios in Table 1 demonstrate the magnitude of the potential improvement in NPV that can be attained by a block by block valuation approach

Mar 15, 2021

By R Ahola, M D. Henschel, M A. McParland

With the introduction in recent years of third-generation interferometric synthetic aperture radar (InSAR) techniques, monitoring of mine slopes, benches and surrounding areas has benefitted from increased accuracy and coverage. Fundamental research into point and distributed scattering techniques has pushed the use of InSAR to provide higher spatial and height resolution. In this paper we discuss the operationalisation of third-generation InSAR techniques and show its application to active mining operations.This paper will discuss the use of multiple independent measurements of ground movement obtained from operationally-derived InSAR products over a wide variety of deformation areas within an active open pit mining operation (ie pit slopes, dewatering depressions, tailings containment and waste dumps). A technique that shortens the time between observations (increased observation frequency) and provides ongoing estimates of measurement accuracy will be described. The methodology exploits available satellite data by using multiple satellites and multiple beams. The paper will also examine factors in the design of a mine survey with third-generation InSAR and illustrate some of the necessary engineering trade-offs to efficiently monitor a mine from space.Overall, this paper aims to demonstrate the capabilities and advantages of operational third-generation InSAR techniques for ground movement monitoring of mining operations and provide a framework for proper design of a mine InSAR survey.CITATION:Henschel, M D, Sato, S, Ahola, R and McParland, M A, 2014. Designing interferometric synthetic aperture radar surveys for mine monitoring with accuracy assessment, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Revell, B Adair, D King, L Keeney

Grade Engineering®, integrated across the mine value chain, has a pivotal role to play in achieving step change reductions in energy and water usage in mine operations. High levels of gangue rejection in the mine can significantly improve mineral head grades and overall productivity. A highly successful example is described at the Minera San Cristóbal (MSC) operation. The nature of the mineralisation in their “intrusive” ore domains in particular has facilitated high rejection rates (75 % of the mass), with significant upgrading of metal to the “accepts” streams (equating to a 2.6 times upgrade in the intrinsic Nett Smelter Return). Results from a series of production trials have confirmed these strong upgrades, resulting in the transformation of mineralised “marginal wastes” to high grade ore feedstocks. If new approaches to more energy and water efficient comminution and separation technologies can also realise gangue rejection at finer sizes in the concentrator, then preconcentration strategies across the value chain also offer the promise of no wet tailings treatment facilities and greatly reduced volumes of waste streams. This “No Tails” strategy is discussed, along with the integrated technologies needed to realise its effect. The work suggests a pathway and insights of a sustainable future for the Minerals Industry, unconstrained by Energy and Water, along with no requirement to produce problematic disposal streams. This strategy has the potential to significantly reposition the social, environmental, financial, and regulatory context of existing and new mining opportunities.

Nov 10, 2020

By C Berglin

Is the Northern Territory different? Certainly it is more remote, has less people and relies more heavily on two or three industries for its survival. On the other hand, its mining industry is governed by Acts not dissimilar to those of the major States - a Mining Act provides the basis for acquisition of tenure, a Mine Management Act provides regulatory control, a Mineral Royally Act collects revenue in return for the right to utilise the land's bounties, an Environmental Assessment Act provides the public face to rehabilitation and environmental safety, and the Aboriginal Land Rights (NT) Act purports to give development criteria for inalienable land use. With the exception of the latter, at least until the advent of Mabo, all these are simply variations on a theme, and are common to most States. This paper will show how the Department of Mines and Energy works in relation to the Northern Territory mining industry.

Jan 1, 1994

By M Monaghan, B S. Gregory

The Geita Gold Mine is located 80 km southwest of the town of Mwanza in the north-west of Tanzania and is 100 per cent owned by AngloGold Ashanti Limited. Open pit mining commenced at Geita in 2000. In 2011, the operation produced 494 000 oz at a cash cost of US$536/oz. This is a significant improvement from 2008, when 264 000 oz were produced at a cash cost of US$742/oz.A period of relatively poor operating performance at Geita was recorded over the period from 2006 to 2009. A period known at Geita as æthe turnaroundÆ commenced in 2009, and has been remarkable to say the least. Over the last couple of years the mine has embarked on a journey, which saw various interventions and initiatives. Among the key initiatives were Project ONE (which focuses on business process framework, systems for people and safety transformation), asset integrity, fatigue management and contract mining of satellite pits.Since the commencement of the turnaround at Geita, gold production has matched market guidance. The mine has returned to positive cash flow on the basis of strong performance on cash management, improved production and increased gold price.This paper explains some of the details of the mine operationsÆ improvements, how they were implemented, their relative contributions to improved mining performance and the path ahead to best practice. Observations will be made about some improvement rules that can be applied generally in open pit mining.CITATION:Gregory, B S and Monaghan, M, 2012. The path to best practice at Geita Gold Mine, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 41-48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

By S S. Kanchibotla, E J. Sellers, L Julian, A Musunuri

Fume events in coalmines are typically associated with wet conditions, soft ground and deep holes. An ACARP research project used laboratory and field testing combined with literature reviews, numerical models and field investigations to characterise the influence of these conditions on the propensity for fume. This paper highlights the results for soft ground and wet conditions and proposes a proactive fume mitigation methodology. A simple numerical model is used to show how fume arises in soft rock that yields more under the loading of high-pressure, water-resistant explosive blends than for ANFO. The blends cool more rapidly after detonation into the lower temperature zone favourable for NO2 production. Low-pressure, high detonation temperature explosives are loaded or charged into soft ground. Water resistance must be considered because soft, faulted and fractured ground can lead to fume from degradation by water flow and non-ideal detonation of product in cracks.A suite of tests were developed to quantify ANFO and emulsion blend performance over time that can be carried out in a mobile laboratory on-site. Index tests such as viscosity measurement and water resistance in beakers are proposed to quantify long-term product performance because small components, such as surfactant, prill impurities and prill fines, contribute to inconsistent product performance. Water ingress experiments and detonation tests aligned with field investigations identified and characterised the role of groundwater in damaging ANFO and causing fume.Fume risk management is achieved using a proposed proactive fume mitigation methodology to characterise influences such as seasonal rain variation, groundwater flow hydrogeology, rock mass strength and structure well ahead of blast design. The design of blasts and selection of explosive products to consider expected conditions will reduce fume, improve efficiency in the mine and offer cost advantages.CITATION:Julian, L, Musunuri, A, Sellers, E J and Kanchibotla, S S, 2015. Mitigation of post-blast fume in soft ground and wet conditions, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 511–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By V Ser, I Smit, C Robertson

Anglo American has been researching the potential benefits of inter-particle comminution techniques for several years. Inter-particle comminution has additional benefits in terms of milling circuit performance such as energy consumption and stability. This paper focuses on the flotation benefits. Inter-particle comminution leads to selective breakage, mineralogical analysis has shown that this leads to improved liberation of the valuable minerals. In addition to selective breakage, the relatively short residence time experienced in typical inter-particle comminution machines allows more efficient classification which contributes to a æsharperÆ product size distribution. The effect of particle size in flotation has been well documented in literature. In general, it is has been shown that there is an optimal particle size range for flotation, and that both above and below this range, flotation recovery is adversely affected. Results show that the narrow size distribution which results from inter-particle comminution improves flotation recovery. Furthermore, the absence of excessive fine gangue material which typically results from conventional fine (-75 ¦m) milling of talcaceous ores, can lead to 100 per cent savings in depressant consumption when such ores are subjected to inter-particle comminution. To-date, this technology has been evaluated on more than ten ores. This paper will focus on one set of results which demonstrates a number of common differences that exist between material that has been milled conventionally and using inter-particle comminution technologies, with emphasis on what the impact of these differences is on flotation performance. A pilot scale (200 kg/h) vertical roller mill (VRM) was used to produce the material, and the results shown will describe conventional laboratory batch, locked cycle and pilot plant flotation testwork.

Jan 1, 2005

The mining industry has expanded significantly in the Pacific Region over the past two decades through a mix of new developments and brownfields expansions of existing operations. Despite this overall success there are also a number of well publicised examples of less than successful minerals ventures. These problem developments highlight the fact that success cannot be taken for granted and that rigorous planning and attention to detail is essential. The dominant growth has come through expansion of existing businesses, notably alumina, iron ore and coal, achieved through both efficiency gains on existing plant and step change capacity additions such as new mines and/or expanded processing plant. This expansion has largely been linked to increased market opportunities. The major issues are the quality and extent of the host resource, achieving the market targets, and the efficiency of the expansion effort. There can be also a range of site specific issues which need to be addressed. The development of new greenfields operations is often more complex as it can bring a wide range of new issues. Depending on the nature of the development, and the companies involved, these can extend from initial financing through to obtaining a market position. Incorporating major new technology and/or establishing infrastructure and attracting staff to remote locations can also add significant challenges. This paper outlines many of the critical factors which need to be considered prior to proceeding with major expansions or greenfields developments. These will be linked to a number of developments in the region over the past decade.

Jan 1, 2004

Avoca Resources LimitedÆs Higginsville Gold Project has a resource base of over 1 300 000 oz of gold. The Trident underground mine, which forms the basis of the project development, has a resource base of 927 000 oz of gold. Avoca is building the Higginsville Gold Project based on a minimum ten year vision, producing over 150 000 oz per annum. The project development has taken less than three years from the Trident discovery hole in October 2004 to the first ore production in June 2007. This paper discusses the background work associated with the development of the Trident underground mine in a difficult period for new project development in Western Australia. The resources boom, led by the iron ore industry in the Western Australian Pilbara region, is creating cost pressures and, combined with a lack of people and equipment, is placing cost and timing stress on a small developing project. Avoca Resources has developed a project execution management strategy aimed at mitigating cost blow outs and schedule delays.

Jan 1, 2008

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Harris, P Kirsch, R LaBouchardiere

æMining + Health in DevelopmentÆ is a project funded by the International Mining for Development Centre (IM4DC, 2012) to develop a centralised database of corporate sustainability initiatives for managing and improving occupational and public health, based on information extracted from social and environmental reports of major mining, oil and gas (MOG) companies. This register of materials has the potential to increase stakeholder awareness of the unique health risks impacting the minerals industry, employees, their families and surrounding communities, as well as to inform stakeholders on global industry approaches to health management.Data and preliminary outcomes from analysis of different MOG corporate sustainability reports on public health and disease management are presented for six African countries (Democratic Republic of Congo, Ghana, Mozambique, Sudan, Tanzania and Zimbabwe) and six Asia-Pacific countries (Indonesia, Mongolia, Pakistan, Papua New Guinea, Philippines and Vietnam).With the minerals industry facing ongoing rapid growth worldwide, including continuous expansion into developing regions, the æMining+Health in DevelopmentÆ project will inform industry, civil society and regulators of current health management practices and programming among the different sectors of the minerals, oil and gas industries and across various regional operations. This baseline information will serve as a resource for minerals industry managers, providing a forum for sharing best practice health management approaches amongst MOG companies.CITATION:LaBouchardiere, R, Harris, J and Kirsch, P, 2012. Mining and health in development - An inventory of global resource industry health initiatives in developing countries, in Proceedings International Mine Management 2012, pp 75-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012