Search Documents

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

By Holla L

There exist several legislative provisions in N.S.W. which work together to control surface subsidence due to extraction of coal by underground methods. The important ones are the Coal Mining Act, Coal Mines Regulation Act, Mine Subsidence Compensation Act and Dams Safety Act. In addition, there are guidelines laid down by the Chief Inspector of Coal Mines for mining under and in the vicinity of tidal waters and the ocean. There are also conditions of coal mining leases and conditions of approvals given to undertake various methods of mining which stipulate further controls. The legislative provisions and relative controls are designed to minimise surface damage, ensure safety , of major public utilities, control- surface land use and compensate damage caused by subsidence as a result of coal mining operations. They aim at balanced and responsible development of our valuable coal resources consistent with adequate safeguards to surface improvements and natural features. The paper discusses in detail these legislative provisions and the mechanics of their operation with a view to emphasising the fact that underground coal mining operations are undertaken responsibly and in a planned and rational manner for the overall benefit of the community. Further, the paper aims to demonstrate the need for legislative measures and conditioning of mining operations to keep abreast of developments in the knowledge and skills of mining and subsidence engineers and continuing improvements in mining technologies. Likewise there is a need on the part of engineers and those associated with introduction of new technologies to appreciate the requirements and existence of legislative and other measures having a direct or indirect association with surface subsidence as a result of coal mining operation.

Jan 1, 1986

This paper describes a mobile laboratory developed specifically for nickel prospecting, and which was designed to be operated by sub-professional staff in remote areas independently of established laboratories. An atomic absorption spectrophotometric procedure was used to determine nickel, cobalt, lead, zinc, and copper ID latentIc and sulphIde samples, with a detection limit better than 25 µg/g for all elements. The procedure was applicable to both soil and drill samples and the accuracy of the procedure, which was ±5 per cent relative at the 1,000 µg/g level was sufficient for the preliminary assessment of mineralized samples and the control of drilling operations. The analytical procedure and the means taken to ensure the necessary reproductibility and accuracy are described. One operator can carry out 400 elemental determinations per 8-hr day at an approximate cdst of 6 cents per elemental determination. The results are returned within a single day, a factor which can contribute materially to the efficiency of drilling operations.

Jan 1, 1970

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

A practical approach has been developed for the design of both grates and pulp lifters. It is based on: an appreciation of the process interaction between grates and pulp lifters, an interpretation of mill charge structure as it relates to discharge through grates, and an analysis of pulp and solids flow in pulp lifter channels. This approach can be used to improve the overall discharge effectiveness of AG and SAG mills.

Jan 1, 2000

The Precambrian Eastern Creek Volcanics comprises spilitic basalts with interbedded sediments and tuffs which were extruded and deposited during Middle Proterozoic time. The rocks have undergone low-grade regional metamorphism.The Eastern Creek Volcanics are approximately 17,000 ft thick and have been divided into four units.The rocks were laid down in a geosynclinal basin elongate to the north. The main structural features are the northerly trending Mount Isa and Gorge Creek-Quilalar fault systems.Major east-west faults cause repetition of the sequence.Copper and uranium mineralization is known within the formation. Copper mineralization is confined to quartz-filled shears anp basalts. Nothing of economic importance has been found in the area though ore deposits have been found elsewhere in this type of environment.

Jan 1, 1968

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

By C Kusi-Manu, E Nyamusika

Geita Gold Mining Limited (GGML) is owned and jointly managed by Ashanti Goldfields Company (Ghana) and Anglogold (South Africa). The mine is currently one of the largest gold producing open pit operations in Africa producing 620 000 ounces of gold and mining in excess of 70 000 000 tonnes of material per annum. The mine currently has 2000 full time employeeÆs and a mine life in excess of 12 years. Geita Gold Mine is comprised of 11 different gold deposits situated in the Lake Victoria Goldfields of North Western Tanzania (Figure 1). The gold deposits are primarily associated with banded ironstone formations within an Archaean greenstone belt. Current global resources, including Inferred, stand at 129.5 million tonnes grading 3.91 g/t (16.2 M oz). Open pit reserves total 70.4 million tonnes grading 4.16 g/t (9.4 M oz). The majority of the gold resource is hosted by the three deposits (Nyankanga, Lone Cone and Geita Hill) within the æGeita TrendÆ a large and continuous (>4 km long) mineralised zone (Adofo, 2002). Geita Gold Mine commenced operations in June 2000, as the second large-scale open pit gold mine in Tanzania. The new workforce of 800 people had no previous experience in open pit gold mining. Since the start of the operation, Geita Gold MineÆs management ambition was to become a world leader in the application of best practice in all technical disciplines and in operational success. Staff development and training was identified as one of the major components in the company achieving its aim. Geita Gold MineÆs management has committed the necessary training staff, resources and the commitment of over $US 1 M a year to staff training and development programs for 2003 and 2004. The process and management of Geita Gold MineÆs mining geology staff training and development program is presented in this paper.

Jan 1, 2003

By Kavetsky A

In surface mining operations, the ease with which a muckpile may be dug is a dominant factor in mining efficiency. Within broad limits, this is largely dependent on muckpile shape and looseness within a muckpile. Moreover, prediction of grade boundary movement and subsequent dilu- tion is of interest to most open cut mines. Such a predictive tool would enable blast design changes to be made to reduce mixing of certain grade regions. At the very least, a good knowledge of post-blast region bound- aries can reduce layout of the grade boundaries and decrease grade dis- crepancies between pit and plant. The model presented in this paper is able to consider various options for a production blast and predict consequent muckpile shapes and grade boundary movements in a three dimensional manner. The overburden geometry, hole patterns, hole inclination and charge distribution are all explicit model inputs. The model divides the rock mass into blocks and calculates a velocity for each block. Three controlling parameters are used in the model, which are related to the explosive energy per unit length of blast hole, energy attenuation of the rock mass and inter-row delay, respectively. The output of the model is a 3 dimensional muckpile shape (contour or any cross section) and a contour map of grade distribution within the muckpile. The model parameters are site specific, since their values depend on the rock condition and explosive-rock interaction which varies from site to site. In order to "tune" the model to a particular site, parameter values must be found which reproduce an observed muckpile profile shape from a given blast design. This calibration of the model requires at least one surveyed muckpile profile shape from a production blast. The model parameters which best reproduce that shape are found by a pattern search technique, and may then be used to predict the effect of changes in blast design on muckpile profile shape and grade boundary movement.

Jan 1, 1989

By L McCarthy, B W. Cuffley, O K. Thomas an

The Central Victorian Goldfield is a world-class field located in Victoria, Australia. It is currently undergoing a revival through activities in the Bendigo, Ballarat, Tarnagulla, Maldon, Castlemaine and other fields. Sediment-hosted auriferous gold-quartz reefs that are structurally and geometrically complex dominate the region. To date, no remote methods have been developed to assist in the targeting of the discrete high-grade oreshoots that characterise the mineralisation. An understanding of the structural setting and controls, and thus likely frequency of repetition of oreshoots remains the main exploration tool. Gold within the reefs is generally characterised by both its coarse nature (>100 up to 10 000 microns) and erratic distribution; as a result, most of the Victorian deposits are classed as high- to extreme-nugget effect systems. This characteristic ensures that mineralisation is very challenging to explore, evaluate and exploit. The key issues facing the explorer and miner are related to effective sampling, and definition of geological and grade continuity, and ultimately grade and tonnage. Tonnage can often be estimated to a reasonable level of confidence, whereas the grade estimate generally carries a medium- to high-level of uncertainty. In these deposits, surface diamond drilling alone is generally only able to define an Inferred Mineral Resource, with underground development, closely spaced in-fill drilling and bulk sampling/trial mining required to define Ore Reserves. The extraction of gold from ores is relatively simple, based on the coarse nature and hence amenability to gravity recovery. Ground conditions and the need for in-stope grade control (eg mapping, sampling etc), generally point toward mechanised cut-and-fill as the primary stoping method in the region. To potential investors this style of mineralisation has been viewed as high risk, because of the associated low confidence in the grade estimate, general paucity of Ore Reserves at mining start-up and need for underground development at the Feasibility Stage.

Jan 1, 2004

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909

This study explores two evolving 3D surveying technologies, photogrammetry and laser scanning, and applies them to deformation monitoring of rock faces and mine highwalls. A quantitative analysis focused on 3D coordinate determination is performed. Furthermore, a qualitative assessment directed at the practicality and viability of each system operating near a rock face or in a mining operation is undertaken to reveal one systemÆs deficiencies over the other. Two photogrammetric and four laser scanning surveys aimed at optimising accuracy and precision within a short period of data acquisition are conducted on the rock face at Organ Pipes National Park, Keilor, Victoria. The accuracy and repeatability of each survey is determined using a combination of iWitness photogrammetric, and Cyclone laser scanning software. The 3D coordinates of targets placed on the rock face are determined by triangulation and resection principles within a bundle adjustment. The coordinates determined by each system are then compared in a 3D transformation. Controlled deformation conditions are established to determine the precision to which each system can detect movement in the rock face. An object of known dimensions is placed on the rock face to simulate deformation. The relative orientation of images taken for the pre- and post-deformation photogrammetric surveys provide an overall 3D point accuracy of 1.255 mm and 1.804 mm respectively. A 3D transformation shows discrepancies of less than ¦22 mm (RMS) between the geometry of the photogrammetric and laser scanning models. Both systems are able to detect the simulated deformation to a precision of 50 mm. This work also identifies how to obtain millimetre accuracy for 3D coordinate determination of rock faces, thereby providing a quality data set for surveyors, geotechnical engineers and mine geologists. Photogrammetry is shown to be a mobile, time and cost-effective technique that is more amenable to mining operations than terrestrial laser scanning. However, both systems demonstrate that they are capable of detecting movements that may lead to failures in the rock face, and possibly endangering human life. The implications are significant for surveyors, geotechnical engineers and mine geologists working in mining operations where enhanced safety conditions, increased productivity and lower operational costs are important considerations.

Jan 1, 2009

By Yucheng H, Baogui Y, Wenyong L

High-water rapid-solidifying material, called 'high-water material', is a new material developed by the authors over many years. The material can solidify nine times its volume of water into solid. The material is a fine kind of binder with special properties. The solidifying body of high-water material with water has quite a high early strength. The compressive strength of the material within three days can reach the same strength as conventional Portland in 28 days. One ton of the material can replace three tons of conventional Portland cement as binder. Some important achievements have been made in application of high-water material. In metal mines, based on the material, a new full-tailing cemented backfill technology has been developed. The characteristic of the new technology is that high-water material is used as binder and full tailing or alluvial sand is used as backfill aggregate. Because of the application of the new technology, major technical problems in backfill technology such as classifying of tailing, dewatering, transportation of pulp, low strength of hackfill body. environmental contamination and so on, have been solved.

Jan 1, 1998

By J Pearce, R Ramanathan

hortly after the World Health Organization declared COVID-19 a pandemic, the words ‘social distancing’ entered the global lexicon. The effects on the public of social distancing, lockdowns and travel bans are well documented. They also present unique challenges to the mining industry. For Hexagon’s Mining division, this posed a significant challenge. We have built our business – our reputation – on regional, customer-focused service and support. True to Hexagon’s values of being professional, engaged and customer-focused, we innovated to overcome the distance dilemma. Making automation a reality for our customers by implementing and supporting technology projects from a distance has helped deepen partnerships by making it easier to tap into our global experts’ knowledge. For example: • Body cameras were at the heart of a successful safety installation at a mine in Ghana. Despite the pandemic lockdown preventing travel by our South Africa staff into Ghana, the project was completed with minimal delays. • Traditionally, implementation and training for our Blast Movement Technology solution is done physically at the mine site. With COVID-19 travel restrictions in place, we have developed and successfully employed a remote deployment methodology. • Using RealWearTM headsets in the field and utilising the knowledge management platform from HINDSITE, Hexagon workshop technicians have been able to support hardware repairs in local offices, which once would have been undertaken in our overseas offices. • The same headset is being utilised to provide clients with remote mentoring sessions by our skilled team members who are based in our regional locations and unable to travel to their site without extensive quarantine commitments. • In instances where our team members have had to travel to site, we have provided consumer technology such as VR headsets to help them cope with long periods of quarantine to and from site. Post-pandemic, Hexagon will continue to refine and improve this method of working. INTRODUCTION Shortly after the World Health Organization (WHO) declared COVID-19 (COVID) a pandemic, the words ‘social distancing’ entered the global lexicon. As governments, healthcare organisations and the public scrambled to respond to the crisis, one thing became abundantly clear: isolation was and, for most of us, still is the key to maintaining our health. Hexagon, a leader in sensor, software and autonomous solutions, was well positioned to pivot and assist in the global response to the crisis. From simulations of the effects of social distancing to mapping the spread of COVID in real time, to drone technology delivering COVID tests, to providing communities with transparent geospatial information, Hexagon solutions continue to help ensure that innovation is readily available to those who need it most during uncertain times. The effects on the public of social distancing, lockdowns and travel bans are well documented. They also present unique challenges to the mining industry.

Jun 22, 2022

By P Kappen, R N. Collins, K M. Spiers

X-ray absorption spectroscopy (XAS) is a synchrotron-only technique used to determine chemical speciation, providing a powerful alternative to most traditional ‘wet chemistry’ and lab-based speciation methods. XAS is an element specific method that can be used to address a variety of systems, ranging from heterogeneous to homogeneous, polycrystalline to amorphous, and solid to liquid. The strength of XAS in identifying and managing chemical species in tailings and mine waste is demonstrated, with the presentation of highly relevant studies into lead, uranium, chromium and arsenic speciation. In each example, waste samples are compared with known standards, allowing an assessment to be made of the quantity of particular chemical species in each.CITATION:Spiers, K M, Collins, R N and Kappen, P, 2015. ‘Forget the wet chemistry’ – how the Australian Synchrotron can help with tailings and mine waste management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 145–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986

The plant and processing site at Porgera has been built on a levelled mudstone ridge about lkm E of the mine. Excavation of 7xl06m3 of soil and rock was necessary to achieve the required area. The exposed mudstone belongs to the Chico Formation and is weak, sheared and readily breaks down by slaking upon exposure. Tectonic uplift and subsequent erosion have produced the present landscape of narrow bedrock ridges, with deep colluvium in the incised valleys. The deep excavation to a maximum of 60m, has rapidly unloaded the mudstone, and subsequent stress relief has caused rebound and dilation of the material. The processes of pore pressure equilibration, softening, progressive failure and loosening, combine to deteriorate the newly exposed rock mass. These processes are commonly associated with pre-existing shear surfaces, fissures and a

Jan 1, 1991

By R Williams, M Baxter, D Zink, R Cunningham

The purpose of this paper is to discuss the efficient operation of a tailings dewatering circuit comprising a thickener and filter press through proper control and automation. It is common to see thickeners and filter press circuits each with their own control systems. This can cause multiple issues when trying to increase efficiency and reliability of the tailings management process. By automating the thickener and filter press controls, you are eliminating any delays and inconsistencies caused by human error and process variations. When done properly the system can maintain a consistent product as the feed characteristics change. Previously, operators would have to monitor the process parameters and adjust the system accordingly. This can now be accomplished using state of the art process control equipment that continuously monitors and adjusts critical variables using Programmable Logic Controllers (PLC) and Proportional Integral Derivative (PID) loops. The paper will detail the control theory used to maintain these systems, highlight other benefits of having a fully integrated plant such as predictive maintenance and remote diagnostics as well as present examples of how these have been implemented in field examples.CITATION:Baxter, M, Cunningham, R, Williams, R and Zink, D, 2018. Tailings process optimisation through automation and controls integration, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 416–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Emerson J

Drilling has always been one of the most important parts of the exploration process with most companies spending around 25% of their budget on drilling. Although superficially there appears to be little difference in drills and drilling practice a number of major refinements have taken place over the last decade that have significantly changed the drilling scene. One of the most important advances has been in hydraulic engineering giving rise to the Dual Purpose top drive drilling rigs. These have led to significant productivity increases with the high rotation speeds and longer fleets. Downhole technology has also advanced with better hammers, stronger drill rods, impregnated coring bits and improved drilling fluids. Although geologists continue to measure drilling performance on a cost per metre basis, greater consideration is at last being paid to the quality of sample produced. This is particularly the case with RC drilling where quite sophisticated automatic and semi automatic splitting devices have been developed. Drill operators are now required to be experienced in both Diamond coring and air drilling and be better qualified to maintain the more sophisticated machinery. Management of drilling companies or drilling divisions has also had to change to accommodate both the high capital cost of equipment and the demands of keeping drilling a cost effective exercise.

Jan 1, 1987

By G Love, S Maher

In Victoria’s onshore Gippsland Basin, geology is driving brown coal developments, and geologists are key decision-makers. Prompted by volatile energy prices and the likelihood of a carbon constrained future, significant work has been carried out on the next generation of technologies to be applied to this giant resource. These include new-generation gasification technologies, coal conversion processes yielding products as diverse as diesel and fertiliser, drying technologies producing thermal and metallurgical coals and in situ conversion processes. However, coals aren’t coals, and brown coal available for new projects will have different quality parameters and mining economics from that currently mined.New projects are likely to be developed on coals with moisture contents averaging 60 per cent and corresponding low energy values. Whilst ash values will be low, averaging just 5 per cent (dry basis), this will at times approach 10 per cent, which is a level that would challenge the installed-generation technologies. Sulfur values will average 0.4 per cent (dry basis), but at times exceed 0.6 per cent, requiring technologies that address the potential for sulfur dioxide emissions. Whilst localised high levels of the fluxes iron (>1 per cent dry basis) and sodium (>0.3 per cent dry basis) would increase fouling of installed technologies, they may be suitable for selected next-generation technologies.Project viability for this next generation of technologies will be strongly influenced by mining cost, and geologists are playing a role in identifying higher-value coal. At its simplest, this is being achieved for open cut mines through regional, vertical strip ratio assessments, which are considered a first-order proxy for mining cost. Follow up assessments are incorporating mining and processing cost, coal quality penalties and product revenues. At a regional scale, it is informing the likely location and relative timing of future mine developments, as well as thinking around rehabilitation strategies, infrastructure and land-use planning.For deeper coal, factors like macro permeability, the ability to isolate seams from aquifers, groundwater chemistry, pressure temperature conditions, connection with groundwater recharge and in situ biota are being used as vectors to in situ coal conversion opportunities.Matching coal to the next generation of technologies has benefited from regional-scale geological studies of coal quality and mining economics, and has benefited from early engagement between geologists, technology developers and project proponents.CITATION:Maher, S and Love, G, 2014. Matching brown coal to the next generation of Latrobe Valley projects, in Proceedings Ninth International Mining Geology Conference 2014 , pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014