Search Documents

Small scale' table concentration tests have many critics. Many metallurgists consider that such tests are of problematical value because of the difficulties involved in conducting and interpreting them.Many kinds of small-scale ore dressing tests are difficult to conduct, and there is, perhaps, good reason for thinking that table concentration tests are amongst the most difficuIt.Interpretation of results from small-scale tests is the responsibility of the metallurgists and engineers in charge, and it is often held that small-scale table concentration tests are particularly difficmlt to interpret.TESTING FOR TABLE CONCENTRATIONOn analysis it appears that the difficulties encountered in conducting small-scale table concentration tests are of three fairly distinct kinds. Firstly, there are difficulties due inherently to the smallscale nature of the operations; for example the smaller width of all mineral bands on the table and the less complete separation due to the shorter length of travel between the feed and discharge points.Secondly, there are the effects of batch operation owing to the fact that the mineral particles behave differently during the initial period when the sample is just beginning to spread over the table, the middle period when feed and discharge are even and continuous, and the final stage, when the last of the sample has been added and the table is beginning to empty itself.

Jan 1, 1954

By C A. Fleming

Gold extraction is largely driven by mineralogical factors, which often cause gold losses to various tailings. Mineralogical factors affecting gold recovery include grain size and shape, surface coating or rimming on gold particles, the presence of cyanide or oxygen-consuming minerals or preg-robbers, the presence of slow-dissolving gold minerals and the refractory nature of submicroscopic gold. Among these factors, locking of fine gold particles in sulfide, silicate and other minerals, either as visible, fine-grained gold inclusions and/or as invisible submicroscopic gold, is by far the most common factor leading to poor gold recovery in gold ore processing. This paper discusses the mineralogical characterisation of gold lost in tailings and its metallurgical implications. The techniques used in characterising the un-recovered gold are also briefly introduced.

Jan 1, 2007

By J G. Petrie, H von Blottnitz

The selection and design of process options to deliver outcomes consistent with sustainable development requires simultaneous consideration of multiple objectives, within a climate of uncertainty û including the environmental and social aspects of technology management in addition to the technical and economic aspects of such. An issue of particular relevance in primary metal production is the deportment of minor and trace components within orebodies, products and wastes and the implications of such deportment for eco-efficiency û in particular, the long-term environmental impact of solid waste management practices. The identification of opportunities to enhance recovery of valuable by-products and simultaneously improve the environmental acceptability of final waste output requires a clear understanding of the distribution of the relevant ore components, which results from the choice of processing route and unit operation efficiency. This is challenging, given that process streams generated during primary metal production are generally poorly characterised and the behaviour and deportment of trace to minor and trace components is not well understood. This paper demonstrates how current data gaps and inconsistencies can be systematically addressed through the meaningful reconciliation of empirical plant data with a fundamental understanding of the mechanisms and parameters influencing element behaviour and deportment during the formation and subsequent beneficiation of mineral ore deposits. On this basis, quantitative distribution data and a comprehensive and comprehensible inventory of unit process inputs and outputs as a function of ore compositions and processing technology options can be generated, which is consistent with early design stage information requirements, both in terms of detail and accuracy, ie is æfirst-orderÆ in nature. This predictive approach to element distribution during primary metal production provides decision-makers with key information in the early design stages of a project (in terms of developing processes within the context of sustainability), whilst simultaneously guiding further data collection and environmental impact prediction studies.

Jan 1, 2006

Oxy-ACETYLENE system of welding and cutting is at present practised in two forms, which may be described as the high and lowpressure systems. In the high-pressure system the two gases, oxygen and acetylene, are delivered. to the blow-pipe under pressure from properly constructed trade cylinders. Oxygen cylinders are in two sizes, each containing 100 and 200 cub. ft. of gas respectively. These cylinders are charged to a pressure of 120 atmospheres, or 1800 lb. per sq. in. approximately. The acetylene cylinders are made in one size as far as the writer knows, and contain 200 cub. ft. of acetylene gas at a pressure of 10 atmospheres. Each cylinder is provided with a valve and connection for attaching a regulator to "break down" the high pressure in the cylinders to the necessary low working pressure of the blow-pipes, and to deliver the two gases at a constant pressure irrespective of the variable pressures in the cylinders. These regulators can be adjusted down to as low as 1 lb. and are provided with two pressure gaugesone reading the contents of the cylinder in atmospheres, and the other the working pressure in lb. per sq. in. The high-pressure, or "two cylinder" system is compact and can readily be transported from place to place in the works. For this purpose the two cylinders are mounted on an easy-running 4-wheeled truck, which the operator and assistant find no difficulty in manipulating. In the low-pressure system the two gases are delivered to the blow-pipe, one from the oxygen cylinder and the other from the acetylene gas generating plant, which consists of the following:Generating cylinder, half filled with water, into which the cathoide is plunged. The generated gas is passed through a filter to the gasometer, then through a water washer on to the hydraullic seal...

Jan 1, 1922

By E Whiteman, L Reyneke, H Horsch

Heavy mineral sand deposits are a source for the economically important element titanium, which is contained in minerals such as ilmenite and rutile. In heavy mineral deposits ilmenite displays various degrees of alteration. Natural weathering of ilmenite involves the removal of Fe and thus results in an increase in the Ti-content. Minerals such as pseudorutile, ferropseudobrookite, anatase and the ill-defined mineral aggregate leucoxene, which consists mainly of various amounts of remnant ilmenite, pseudorutile, ferropseudobrookite and anatase, are typical replacement products of ilmenite. Ferropseudobrookite occurs as a recrystallised, optically and chemically distinct mineral phase. Textural relationships suggest a diversity of physicochemical conditions including weathering and metamorphism that led to the formation of complex mineral assemblages and textures. In the heavy minerals industry the alteration products of ilmenite are generally referred to as æaltered ilmeniteÆ and/or leucoxene. The distinction between æaltered ilmeniteÆ and leucoxene is not consequently defined and is very much dependent on economic factors and specific mining operations (ie determined by deposit specific mineral assemblages). Generally the term leucoxene is used in the heavy minerals industry as a collective description for ilmenite alteration products with TiO2-components ranging from 65 - 95 per cent. A detailed comparative mineralogical investigation including microscopic, SEM and QEMSCAN« techniques show that it is possible to identify and quantify the replacement products of ilmenite on a micron scale. QEMSCAN« generated particle maps were graphically compared with photomicrographs taken by applying reflective light microscopy. The resulting information can be integrated over the entire sample with respect to composition, absolute and relative mineral abundances, grain sizes, volumes, densities, textural relationships and liberation potentials. This provides a powerful tool for a first appraisal of the physicochemical behaviour of bulk samples and individual particles during metallurgical processing.

Jan 1, 2008

By D Kepert, M Absalom, N Nitschke, C Fowers

The discovery of the Nyidinghu Iron Ore Deposit totalling 2.46 Bt of resource continues FortescueÆs highly successful exploration record of discovering multi-billion tonne deposits under cover with little to no surface expression. Since inception in 2003 Fortescue have discovered and delineated the Christmas Creek and Cloudbreak deposits in the Chichester Range totalling 3.38 Bt and 3.25 Bt in the Solomon region. Together with other deposits Fortescues resource portfolio now approximates 10 Bt of hematite - goethite mineralisation.The Nyidinghu deposit is situated on the southern margin of the Fortescue Valley, 35 km south of FortescueÆs Cloudbreak mining operations on the north margin of the valley. Nyidinghu comprises approximately 70 per cent BID martite - goethite mineralisation hosted by the Brockman Iron Formation and 30 per cent CID beneath alluvial outwash of the Weeli Wolli Creek in to the Fortescue Valley. Minor DID mineralisation occurs at the deposit margins.BID mineralisation is strongly controlled by the pre-existing NE/SW trending Weeli Wolli Fault system and bounded to the north by the Poonda Fault. Both fault systems are interpreted to have had a long and complex history commencing pre Ophthalmian Orogeny (ca 2.2 Ga) and remaining intermittently active through the Proterozoic.CID at Nyidinghu is the downstream continuation of the combined Weeli Wolli/Marillana CID palaeochannel system being mined by Rio Tinto and BHP Billiton at Yandicoogina and Yandi, respectively.Exploration commenced in August 2010 with the inaugural resource announcement of 1 Bt being made just six months later. To date over 1700 RC and 85 diamond core holes have been drilled forming the basis for the resource of 2.46 Bt and ongoing feasibility studies. Current exploration activities continue to delineate new mineralisation at Nyidinghu with an ultimate target tonnage of 3 Bt.CITATION:Fowers, C, Kepert, D, Absalom, M and Nitschke, N, 2013. Discovery, geology and structural setting of the Nyidinghu iron ore deposit, Hamersley Province, Western Australia, in Proceedings Iron Ore 2013 , pp 81-90 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By T Higuchi, L Lu

The quality of iron ore fines have been deteriorating, which has affected sinter quality and productivity adversely. New pretreatment and sintering technologies are therefore required to tackle the gradual change in the quality of iron ore fines. In the sintering process, iron ore fines are first granulated with fluxes such as limestone and coke breeze, and are then loaded and fired in a sinter machine. Sinter productivity and quality are heavily influenced by the reactions occurring in the sintering bed. Hence fundamental understanding of these high temperature properties of ores is urgently needed.Formation of initial sinter melt, penetration and assimilation of nucleus particles by the initial melt, and consolidation and final solidification of final sinter melt are believed to be the key sintering reactions. The assimilation and penetration phenomena have been studied separately in the literature with model particles and diffusion couples and are therefore difficult to relate to sinter quality. In addition, the effect of ore mineralogy has not been studied in detail.In this study, tablets consisting of coarse particles from various iron ore fines as nucleus particles and chemical reagents as adhering fines were made and fired under various sintering conditions to investigate the penetration and assimilation behaviour simultaneously. The degree of assimilation, pore structure, compressive strength of the resultant analogue sinters were evaluated and the relationship between sinter strength and ore characteristics was further discussed. The nucleus particles from Ores A and B were found to be more porous and assimilated more readily with sinter melt, resulting in a viscous melt and a macro-porous sinter structure. The nucleus particles from Ores C and D on the other hand, assimilated less readily with sinter melt, resulting in a fluid melt and a denser sinter structure. This is consistent with the results reported in the literature, suggesting that the present evaluation method can be utilised for studying sintering reactions and predicting sinter quality.CITATION:Higuchi, T and Lu, L, 2017. Evaluation of sintering behaviour based on ore characteristics, in Proceedings Iron Ore 2017, pp 303–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Mineral exploration and mining in New Zealand has had almost five years of new legislation. The requirement for different consents is a challenging, time consuming, expensive exercise but in most cases the new procedure is working, although the matter of obtaining access to land is still a major issue. Priority is critical. After lodgment of an application for a minerals permit there are many other matters to address such as identifying land owners, occupiers and administrators, preparation of access applications, consultation and preparation of various resource consent applications.

Jan 1, 1996

CHAPTER 1 - GENERALIn the introduction to this chapter a general account is given of the growth of the mining industry in Western Australia from J88G, when the output of gold for the whole State was only £1148, to 1908, when: the output had risen to £6,999,885. In 1903 the output reached £8,770,719.It is quite evident that the discovery of gold in Western Australia was the means of opening up the road to broader industrial expansion, and it is doubted if any other portion of the British Empire more clearly exemplifies the nation-building forces of metalliferous mining than this State.The chapter includes an account of the following situation and history of the field.CHAPTER 2 - GEOLOGYIn this chapter the classification of the rocks of Kalgoorlie, but particularly those on the Golden Mile, is considered. Each rock is described in detail, and microphotos are shown to indicate the most important features in each type. As far as the Golden Mile is concerned, it is held that, notwithstanding the general chemical and more or less dynamical metamorphism which the rocks have suffered, it is possible to divide them into six groups...

Jan 1, 1912

By W E. Vance, B H. Ashton

The emission of seam gases into underground workings in coal mines is acknowledged as a major hazard, particularly methane due to its possible ignition. Acknowledge of seam gas parameters is important for the prediction of gas emission rates into the ventilating air current. They are also important as the basis for the evaluation of the likely contained gas as a possible energy source.   Gas content determinations for the Kupakupa seam have been made at the Huntly West Mine.  Applying the method of Creedy (1986) to face samples, gas contents of 1.80 and 1.66 have been determined. Using desorbed and residual gas content data a content of 1.92 m3/t has been derived. These are on an ash included basis. Calculations using the adsorption equation of Kim (1977) and coal quality have given a gas content of 2.19 m3 t. Long-hole exploration drilling at Huntly West Mine has provided information on gas pressure. A pressure rise test has given a reading of 500 kPa (absolute); this is low compared with the pressure given for the determined gas content from theoretical adsorption isotherms.

Jan 1, 1991

By J Kleynhans, D Vermeulen, V Cogho

A number of rehabilitated open cast coalmines in SA are already decanting. The paper focuses on the situation at one of these mines where the following information exist: monthly decant rates and rainfall; sulfate concentrations of the decanting water; water level measurements inside the mine prior to decanting; ABA analyses; information about the rehabilitation (drainage slope, vegetation, soil used). A 2D-model was constructed for the mine and calibrated against six years of flow data. About 85 per cent of the decant outflow rate comes from direct recharge on top of the rehabilitated mine while the other 15 per cent is derived from lateral groundwater inflows. The estimated recharge value was 17 per cent of the rainfall. Measured sulfate values showed that the sulfate generation rate for the mine was in the order of 7 kg/ha/d. Conclusions from the study are:most of the water decanting from rehabilitated open cast coal mines is derived from recharge via rainfall; given a specific sulfate generation rate, then: the lower the recharge the less the decant rate but the higher the sulfate concentration of the decanting water and vice versa; future prediction of the decant rate must be stochastic according to expected percentile monthly rainfall values; and as a first assessment of the predicted sulfate concentration of decant water from rehabilitated open case mines, the 7 kg/ha/d sulfate generation rate can be used.

Jan 1, 2003

By P F. Lauricella, D Hendri

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade 'feeder' system flanked by tabular, inward dipping, moderate grade 'ouflow' zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (=10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (<10 microns), disseminated and fracture-controlled arsenical pyrite. The Mesel deposit developed where high angle faults guided ascending, sulphidising fluids into reactive carbonate stratigraphy adjacent to and beneath the andesite intrusion and during subsequent migration of the auriferous fluids along 'outflow' channels. Early decalcification and dolomitisation enhanced porosity and permeability prior to silicification and sulphidation. Gold deposition occurred late in the genesis of the deposit.

Jan 1, 1995

By J L. Mauk

The Gladstone Hill area hosts epithermal veins similar to those at Martha Hill, which is less than one kilometre away. There are several vein types in the Gladstone Hill area including (1) pyrite-marcasite, (2) quartz, (3) base metal sulfide, and (4) calcite. Pyrite veinlets formed first, whereas the quartz and carbonate veins formed later. The base metal sulfide vein occurs at depth and is predominantly comprised of quartz and chlorite intimately intergrown with pyrite, sphalerite, galena, and rare chalcopyrite. Platy calcite and massive calcite veinlets were the last vein types to form. Several vein textures occur in the Gladstone Hill area, including colloform and crustiform banding, lattice-bladed, zonal, comb, massive and feathery textures. Crustiform banded veins are the dominant texture and contain variable gold-silver grades. Colloform banded veins consist of ubiquitous quartz and minor chalcedony with gold grades as high as 60 g/t. The lattice-bladed texture forms from the deposition of calcite, which has been replaced in many samples by quartz, indicating that boiling and later cooling has taken place. Unreplaced platy calcite only occurs at deeper levels (>300 m). Zonal and comb textures are preserved in quartz and late-stage amethyst veins. Feathery textures within quartz are commonly associated with breccias and some colloform banding, and with significant Au-Ag grades.   The homogenisation temperatures (Th) of primary and secondary inclusions in quartz, amethyst and platy calcite range from 166 to 274¦C, with salinities <1.3 wt% NaCI equiv. The presence of vapor-dominated inclusions and primary fluid inclusions in platy calcite suggests that boiling occurred intermittently throughout deposition. The veins formed under a relatively flat lying paleowater table that occurred 280 - 300 m above sea level. The fluids involved in vein formation were alkali chloride in composition and low in CO2.

Jan 1, 2001

By M J. Begbie, K B. Sporle

The Golden Cross low sulfidation epithermal deposit produced approximately 750,000 ounces of Au from two ore zones: the underground Empire Vein System and the open pit stockwork. The Empire Vein System has at least eight stages of vein formation: (1) sulfide veins, (2) black veins, (3) massive veins, (4) banded veins, (5) thin white veins, (6) crumbly veins, (7) massive/platy calcite veins, and (8) flattened rhomb calcite veins. Gold mineralisation occurred relatively early in the lifetime of the system, dominantly during 2 through 4. The late calcite veins (7 and 8) and early sulfide veins (1) are barren. The vein system formed in a dominantly extensional environment, though some compressional faulting may have also existed during vein formation. There is no evidence for significant strike-slip faulting during vein formation, highlighting the fact that explorationists should pursue on-site structural patterns rather than fashionable models.

Jan 1, 1998

By Creelman C. A

The removal of a horizontal piIlar between Nos. 9 and 11 levels (1,116 feet from the collar of main shaft) was successfully carried out by blast hole drilling, and, to the best of the authors' knowledge, this mass blast of 40,000 tons of ore (requiring the use of 7,150 Ibs. of explosive and 5,385 feet of primacord) was the first occasion on which a task of this magnitude has been carried out underground in an Australian mine.Blast hole drilling was introduced by this company approximately fifteen months ago at New Cobar Mine in sub-level stoping.This experimental drilling and blasting gave very valuable information as to the correct technique to be adopted when the final plans were being prepared for the removal of the horizontal pillar at New Occidental Mine.The dimensions of this pillar were approximately 15 feet long, and from 40 to 60 feet wide, and 65 feet in depth.The block of ore extended to 35 feet above the level and 30 feet below, the upper section being partially excavated to form the bell-hole floor and grizzly chambers used for drawing off the broken ore in the shrink stope above the No. 10 level.Description of Ore-bodyThe main ore-body is situated almost vertically in a well-defined shear zone at the junction of sandstone and slate, the sandstone forming the eastern and the slate the western wall.The ore-body consists of highly silicified slate (chert) sparsely impregnated with sulphides, containing a small percentage of copper and bismuth.The total length of the ore-body is approximately 450 feet, with a maximum width of 60 feet in the main section, which is about 200 feet long.This is the section shown in longitudinal and cross-section (Fig. 1).The ore-body is divided by a horse of mullock in the northern end into two legs, the eastern and western, which are approximately 250 feet long and averaging 25 feet in width.This ore-body is strong, hard and abrasive with extremely strong walls, an ideal proposition for open stoping and mass blasting.MiningIn all levels above No. 9 the cut and fill method of ore extraction was adopted. On Nos. 10 and 11 levels the shrinkage method was introduced with economical results, and no difficulty had ever been experienced with shabby or bad walls.Shrink stoping had been carried upwards from No. 11 level to within 10 feet of No. 10 level, when mining hazards developed, and instead of...

Jan 1, 1944

By Peres EC

The flotability of monazite, zircon and rutile in the presence of sodium oleate, potassium octyl hydroxamate and a commercial hydroxamate was investigated through microflotation tests in a modified Hallimond tube. Zeta potential determinations in the absence/presence of collectors were performed in a microelectrophoretical cell. The microflotation testwork showed that, in general, the flotability characteristics of all three minerals are very similar. Commercial hydroxamate is, by far, a stronger collector than the pure potassium octyl hydroxamate. Electrokinetic studies indicated that the adsorption of collectors shifts the isoelectric point (IEP) of the minerals towards lower pH values. These collectors also are capable of changing the zeta potential values to more negative figures in the pH region above the isoelectric point. An increase of the conditioning temperature, generally, enhances the floatability of the three minerals. A depressant is required in order that selective flotation is feasible in the system monazite-zircon-ruffle. Sodium metasilicate is an efficient depressant for zircon and rutile and affects only slightly the flotability of Monazite.

Jan 1, 1993

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

Lignite deposits of Central Otago Miocene Dunstan Formation accumulated on a broad alluvial plain and on deltas that flanked a large freshwater lake. The regional subsurface distribution and configuration of the lignite-bearing strata are identified within the context of depositional systems and placed into a genetically defined stratigraphic framework. The stratigraphic and depositional models constructed, should form an integral part of the geological assessment process to guide future regional or mine based lignite drilling programmes. Further testing and evaluation of the commercialy important lignite deposits in the Blackstone and Roxburgh Coalfields are required to adequately characterise the lignites and their geological setting, particularly to select methods of mining and wise uses of the lignite.

Jan 1, 1992

When a major mineral find has been announced the general perception is that a battle between Aborigines and the mining company involved will inevitably occur.It is a fact that many miners in the past have not had a good relationship with Aborigines because of their indifferent attitudes towards them. They saw no common future and went their particular way. However, attitudes have changed significantly since Noonkanbah and both miners and Aborigines are seeking common ground in order to achieve mutual benefits from the establishment of a mine on or near Aboriginal land. There are many obstacles that both miners and Aborigines need to overcome inordertofindthiscommongroundtoachieveawin/win situation. The obstacles can be found in entrenched ideas and practices which need overhauling, not the least of which emanate from government policy and requirements.Without going into specifics, the Noonkanbah incident during the 1970's where Aborigines and their supporters confronted miners who were ordered by the Western Australian governmentto drill on Aboriginal land, polarized Aborigines and miners. Since this incident, many Aborigines, particularly those in the cities, have had the attitude that mining and Aboriginal culture are in direct conflict. Aboriginal opinion is generally shaped in the larger cities through mass media coverage of the opinions of urban Aborigines and their supporters. Through no fault of their own, these Aborigines were removedfromthe land of their ancestors and have notlived atraditional Aboriginal life-style for a number of generations and most have little knowledge of, nor have had involvement in, traditional Aboriginal lore and culture. For the most part these people live in awestern life-style and few still know their language. They generally have high profiles, often giving viewpoints that are wrongly considered "Aboriginal" and supposedly representing all Aborigines. This group is very different with their thought processes and values from those Aborigines who live on their own traditional lands with a traditional life-style, and practise their age old ceremonies. Their tribal values are based in their relationship with the land, expressed through complex religious ceremonial rites of song, dance and legend. Today this group is very much diminished in numbers but nevertheless in the region of the Gulf of Carpentaria there is a high proportion ofpeople who practise their lore, speak their own languages and pass on traditions to their children. It is well documented in the history of Australia that Aborigines have been decimated in numbers and whole tribes have been wiped out. Certainly in this region the experience has been no different.

Jan 1, 1993

The process of refurbishment is not a precisely defined one. It is under- stood to mean an upgrading of a plant which is normally performed only once. The application of refurbishment in the field of materials hand- ling equipment poses particular problems because complex plants con- sist of individual components having quite different remaining service lives. For this reason, a systematic, proven procedure is proposed for the refurbishment of large materials handling equipment, designed to ensure economic implementation in accordance with the company goals. Rheinbraun2 has been using materials handling equipment since 1900, the largest units today being bucket-wheel excavators with a daily capacity of 240,000 bank cubic metres of overburden and a service weight of up to 13,500 t (metric tons). Since 1975, more than 50 large-scale refurbish- ment projects have been carried out in the company. In the process, refur- bishment has turned out to be the proven alternative to replacement of large materials handling equipment. Rheinbraun Engineering,3 a Rhein- braun subsidiary, carries out planning, consulting, and supervising work in the implementation of refurbishment projects in Germany and abroad. The most recent example is the refurbishment of Dredger 11 of the State Electricity Commission of Victoria in cooperation with Krupp-Australia, Melbourne.

Jan 1, 1989