Search Documents

By R J. Holmes

The procedures and equipment used for sampling iron ore process streams have generally improved in recent years. However, there are a number of areas where significant issues still commonly occur, including sampling high capacity streams, sample cutter design and operation, division of primary increments at the secondary sampling stage, the performance of crushers installed to reduce the particle size prior to sample division, and the sample mass that is retained at each sampling stage. These issues of non-conformance with correct sampling principles are caused by factors such as increasing the speed and loading of conveyor belts to increase throughput, which changes the trajectory of the ore stream and may result in an inability of the sample cutter to handle the increased flow rate without sample loss. Failure to sample the entire primary increment stream at the secondary sampling stage is also a common issue as well as failure of crushers to provide crushed products of the required particle size due to ongoing maintenance and/or adjustment issues. These common pitfalls can all be addressed through careful attention to detail.CITATION:Holmes, R J, 2017. Common pitfalls in sampling iron ore, in Proceedings Eighth World Conference on Sampling and Blending , pp 261–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

A number of forecasting methods are available to mine management to help predict the most likely outcome of some particular event thus enabling management to make more cost effective decisions. Three general classes of models can be used to predict future events qualitative, structural and time series, the most effective method in most cases being time series. Time series methods can be applied to predict future events from a series of past observations. Various time series techniques are reviewed with a comparison of their relative advantages and disadvantages.

Jan 1, 1980

Over the last five years the :forward momentum in the Australian resources sector has been dominated by gold production and exploration companies. While reporting of exploration results to shareholders and Stock Exchanges has generally been detailed and responsible, the standards of reporting ore reserves still leaves much to be desired in terms of contemporary investor expectations. Australian gold ore reserve reporting practices are critically examined and suggestions are made as to how gold mining companies can enhance stock market recognition by investors through more informative and useful Reporting.

Jan 1, 1987

A system of decline mine entries and ore haulages has been designed for the Mt. Windarra mine. This choice was controlled by the nature of the ore- bodies, the mining method chosen and the capital cost of development re- quired for production. Mine entries are being driven 4 metres high and 5.5 metres wide and decline at 11%, to accommodate diesel haulage vehicles of 35 tonnes capacity. The.Mount Windarra haulage system and the design parameters used in its selection and design are discussed, and general design and selection parameters are proposed.

Jan 1, 1973

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By Quemard D, Troncoso J

The Gordonstone Project with a capital cost in excess of $500 million will become the largest underground coal mine in Australia. The project development decision was taken on 31 July, 1990 and at 31 May, 1991 construction was approximately 35 per cent complete. The first train of processed product coal will be railed to Gladstone during December 1992. The general theme of this paper therefore will address the planning and development processes at Gordonstone particularly the interrelatedness of technical, production, construction and environmental disciplines to ensure success during operations.

Jan 1, 1991

To finalise the arrangement and details of the headframe to be erected over the new No. 3 Shaft, the haulage and winding equipment requirements were first determined, then tentative designs were prepared to cover the needs of general shaft servicing work for men and materials, mullock and ore handling, and the probable requirements of a breaker station to be built adjacent to the headframe, which would provide for the crushing of the run-of-mine ore down to a size which would be suitable for feeding on to the concentrating mill.

Jan 1, 1957

In the 1890s, The Goldfields Water Supply Department in Western Australia commissioned the diamond drilling of two deep artesian exploratory water bores near Coolgardie (Blatchford, 1899). At the time, in spite of strongly-worded advice to the contrary from the Government geologists, there was a wide popular belief that you could obtain artesian groundwater virtually anywhere providing you drilled deep enough. The first Coolgardie hole was drilled to over 900 m, despite the fact that the bore penetrated granite from a depth of 5 m below the surface. Drilling proceeded for more than 16 months, between July 1896 and November 1897. A small quantity of salt water was struck at a depth of 36 m. The second bore was mercifully terminated at a depth of 50 m, also in granite, with again only a small inflow of salt water. Such were the desperate lengths that were pursued to obtain a reliable water supply for the influx of people in the Eastern Goldfields gold rush. The WA Goldfields continued to rely on huge condensers for water supply until that great engineering feat, the construction of a water pipeline from Mundaring Weir to Coolgardie, was completed in 1903. An enormous network of rail tracks penetrated outwards from Kalgoorlie and Coolgardie for the collection of timber, principally to feed the condensers. Remnants of the rail network are still visible today. The acute shortage of fresh water led to great deprivation, disease and death among the early miners. Today, the water problems faced by the mining industry are thankfully not as severe, but they are nevertheless no less challenging. The southern part of the WA Goldfields is a notoriously difficult area for finding potable quality groundwater. Even as recently as the 1990s, there were occasional serious efforts to find potable groundwater in that area, some very imaginative and innovative. One mining company, working south of Southern Cross, spent many months experimenting with recovery of potable quality water from a shallow freshwater lens overlying hypersaline water in a low permeability weathered granite aquifer. They used very low capacity pumps manufactured from car windscreen washer pumps powered by solar panels.

Jan 1, 2000

By Andrews JRG

Chrysotile asbestos is a valuable resource. Used as a reinforcement in asbestos cement, products are obtained which are cheap, are not attacked by vermin, do not rot or support growth of fungi and are unaffected by water or humid conditions. Such products are of great value in the developing countries where inexpensive and durable building materials and pressure pipe are very important to development, housing and water supplies. Concern over the adverse effects of inhaling asbestos has led to the introduction of increasingly stringent controls world wide on the quantities of airborne asbestos per- missible in the occupational situation. Wet processing has the potential for virtually eliminating the environmental concerns with asbestos dust both in fibre production and in the materials handling section of the manufac- ture of asbestos cement products. In addition, high efficiencies associated with wet process- ing mean that better yields are obtained and that the tailings which are dumped have a lower residual asbestos content. Since early 1977, ICI Australia and Woodsreef Mines have been engaged in a programme of research to develop and evaluate a wet mill- ingprocess to produce, from ore and existing tailings, high grade fibre suitable for use in asbestos cement products. The process has been developed through microscopic studies, labora- tory bench scale experiments, work in a small scale semi-continuous plant and product evalua- tion on experimental size Hatschek asbestos cement machines. A prototype mill with a normal feed rate of 1z tonnes per hour and capable of producing pipe grade asbestos from Woodsreef ore has been constructed and was operational from January, 1982 to July, 1983. A range of asbestos cement products have been made successfully on full scale Hatschek machines using fibre from ore and tailings milled in the prototype mill. Economic evaluations indicate that a wet process mill would be cheaper to build, operate and maintain than an equivalent dry process plant. A commercial plant has been designed 1. Manager New Process Development, Woodsreef Mines Limited, Barraba, Australia. 2. Senior Lecturer, Department of Chemical Engineering, Monash University, Vic, Australia. formerly Senior Research Officer, Research Department, ICI Australia Limited

Jan 1, 1986

Transport technology has produced social changes since the invention of the wheel five millenna ago when man was freed from the need to expend large amounts of energy to move goods and people. Further impetus came with the Industrial Revolution when mechanical power producing devices were applied to land and-water transport. This leap, together with the application to air transport has caused enormous social changes in our way of life. The state of technological advancement of transport modes has dictated to a large degree the develop- ment of Australia and Papua New Guinea. It is suggested that we should not make advances for technology's sake but examine the real needs of the users of transport and ensure that the un- necessary costs are not incurred. The transporting techniques for the ore, waste and slurries used by Bougainville Copper in Papua New Guinea are, in general, quite conven- tional but the scale of operations and the location has modified some modes. in particular the soft' overburden and concentrates were slurried for trans- port and the lack of experience in humid climates restricted the choice of the mine haulage truck. The near future of the transport. industry is seen as an expansion in equipment sizes but the suggestion is made that we need to examine more than the economic and technical aspects; it is necessary for the social con- sequences of our actions to bear examination by outside opinion

Jan 1, 1973

Modern technology and the need for published results have created the tendency for exploration to concentrate on drilling and assaying rather than building a broader geological understanding. Though grade is vitally important to a resource estimate, density and volume are also very important aspects that require equal consideration. Wet tropical nickel laterites are developed in humid environments over ultramafic bedrock where the nickel and cobalt are enriched to economic levels by weathering, leaching and supergene processes. These laterites often occur over rugged terrain at higher elevations where there is sufficient rain and stability for the long lateritisation process to occur. For nickel laterite profiles, the variable terrain and significant material type changes within the relatively thin profile make density and particularly volume estimation, just as significant as grade in resource estimation and assessment of resource risk. Drilling alone is generally not a cost-effective way to reduce the risk in laterite volume estimation to acceptable levels. Surface geological mapping, high resolution topographic data and other information such as ground penetrating radar (GPR) can be used very effectively to improve volume estimates. These data types are all differently structured, have different data density and quality and may potentially overlap. Integration of these disparate data types provide the most cost-effective approach to modelling wet tropical nickel laterite volumes and minimising risk. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By J E. Everett, M L. James

When iron ore is crushed and split into lump and fines components, there are systematic differences between the lump and fines grades. Generally the lump product is richer in iron and lower in the other minerals, compared to the fines product. The grade differences between lump and fines, together with the lump percentage, are referred to as the ælump algorithmÆ. Mine estimates of grade, based on exploration or blasthole drilling, relate to head grade. The ælump algorithmÆ predicts lump and fines product grades from the head grade. This knowledge is important when developing mine plans. Different ore types can be expected to have systematically different lump algorithms. Previously, lump algorithms for specific ore types have been estimated by running the crusher with a single ore type over a sample period. This method is costly, interferes with production, and yields results of limited statistical power. It has been found that weighted-least-squares (WLS) multiple regression can be used to ascribe lump algorithms to different ore types, provided sample periods have sufficiently varied ore type mixes. This study discusses the method and its application to the analysis of Mining Area C crusher production records to estimate the separate lump algorithms, which could be applied to the different ore types. The analysis has enabled the set up of lump algorithms in the production system, to improve the grade control of lump and fines product. Some other relevant applications of the WLS multiple regression approach are also considered.

Jan 1, 2005

By M Noppe, I Glacken

There are many critical nodes along the mine value chain, from orebody to mineral product, and inter-disciplinary input is required to analyse the variability and uncertainty at each node in order to identify and mitigate areas of risk. Mining differs from many other industries in that the variability in the product is dictated largely by the inherent nature of the input material (the orebody). The true characteristics, including the variability of the orebody, are never known exactly and are instead based on estimates derived from sample data. A further difference is that bottom-line gains are largely controlled by world commodity prices, which can vary with time, rather than by local supply and demand issues. Methods for identifying, reporting and responding to this inherently variable raw material are discussed. These include analytical and reporting methods, equipment and software, risk analysis and reality checks (eg reconciliation). Sampling results, mineral resource and ore reserve estimates and economic assumptions are a function of the variability of the orebody. Risk quantification should be expressed as a level of confidence, which takes into account the scale or period over which the risk is being assessed (life-of-mine, annual or shorter production periods) and should convey the likelihood, severity and consequence of occurrence of a given event. The future generation of mining specialists needs to understand the entire mine value chain to better manage risks and maximise mine dollar-value.

Jan 1, 2002

The implementation of a process information management system (PIMS) is to provide a single online, real-time information system. This system provides a unique and completely open view for everyone, based on the key business drivers. It is structured around the three key concepts: process, maintenance and stocks. It combines numerous applications and provides accessibility to common tools and reports, through a web-based user interface, for every one from the floor operator to the General Manager. This æunique and commonÆ view displays raw, online process information that provides a quick health check of the operation at a glance, highlighting areas that require further investigation. The system is based on a hierarchical system of views, from the overview of the whole plant flow sheet to the more detailed operational shop view. It provides a synthetic view between continuous and batch operations, enabling the tracking of each batch produced. The batch view displays the critical batch components, and a comparison with each component of an ideal batch. This enables detailed analysis of each batch to identify areas of improvement. The information system will consist of an online reconciliation of stocks and flow data. This enables focus on the recovery of each process unit on a regular basis. This paper discusses the design strategy for the Process Information Management System, to ensure a unique and open view on the key business drivers is achieved and implemented successfully.

Jan 1, 2005

Longhole open stoping was introduced in the zinc-rich 'B' lode at New Broken Hill Consolidated Limited (NBHC) during 1968. Since then one longitud- inal and a series of transverse longhole open stopes have been developed. The longholes are drilled using Gardner Denver airtrac drilling jumbos and the broken ore is loaded from drawpoints and transported to chutes using Wagner ST5 scoop- trams. The holes were drilled from sill stopes 160 ft apart. The width of an emptied transverse longhole stope was successfully widened by blasting rings of blastholes drilled parallel to the stope wall. Proposed stope and pillar designs for a series of transverse longhole open stopes were assessed using a method of finite element analysis, applied to a longitudinal section through the area. Blastholes have been surveyed for dip and bearing using an Eastman borehole survey camera. The data produced has provided the basis of a study of blast- hole deviation. Deviation of boreholes is considered to be the major cause of the formation of benches in longhole stopes.

Jan 1, 1971

By A H. Clemens, T A. Moore

This paper discusses a number of technical issues related to marketing coal. It outlines how the results of research undertaken in New Zealand and overseas can help producers address a range of technical factors that impact on production costs and marketability. The paper also discusses trends in coal utilisation for power generation and how new technologies may require coal with different characteristics. Research and development into options for CO2 sequestration are discussed including carbon storage in forests, and removal of CO2 from flue or fuel gas in power stations, and its disposal.

Jan 1, 1997

Environmental management of minesites in general, and management of water discharges in particular, is receiving ever-increasing attention. One key component in the successful design and operation of water management systems is to address the presence of sediment in the water being conveyed. Sediment erosion in the mining environment is often greatly exacerbated by disturbing the ground surface of vast areas of catchment. If sediment avoidance, transport, deposition or release are not adequately addressed, the impact on water management facilities can include loss of storage and hydraulic capacity, more frequent equipment replacement, increased operational costs and potentially environmentally unacceptable sediment discharges to receiving waters. An overview of sediment management within water facilities is presented here, and design of one particular approach, the use of settling basins for sediment removal, is discussed in detail. Examples are used to illustrate lessons learnt where particular approaches to sediment management have been found to be lacking. The common themes in the lessons learnt include the need to characterise hydrodynamic conditions and sediment properties in the water source, to set performance targets for sediment management, and to develop operating procedures to meet these targets under a realistic range of scenarios. The examples show how analysis of expected performance of sediment management can help with planning of operation and maintenance strategies. For settling basins, use of a simulation model that includes the effects of turbulence on settling can provide considerable benefits in optimising basin design and evaluating performance. Even in the most basic approach to sediment settling, establishing performance targets based on design flow and sediment characteristics is critical.

Jan 1, 2003

Marble deposits of dolomitic variety are available in large quantities in India and for extracting these deposits diamond wire saw cutting machine is mainly used. Cutting performance of the diamond wire saw machine depends on rock parameters, machine parameters and operational parameters. Rock parameters related to physico-mechanical properties, such as, compressive strength, tensile strength, shear strength, modulus of elasticity and abrasion resistance of marble play role in determining cutting rate and beads wear rate. Thus, this study was undertaken to determine the relationship between different physico-mechanical properties and cutting performance. This work also aimed at enhancing the cutting performance of diamond wire saw in dolomitic marble deposit. Study was conducted in the field at three different zones having deposit of soft, medium hard and hard dolomitic marble. During the study, cutting rates and wearing of diamond beads were recorded in the field. Physico-mechanical properties were determined in the laboratory. The results obtained were subsequently evaluated by using statistical analysis. Study revealed that these properties of marble play a significant role in the performance of diamond wire saw machine. Predictive equations for the wearing of diamond beads and cutting rate were developed based on regression models. Results of this study will be of ample use for operators of wire saw to achieve maximum cutting performance and for manufacturers in designing the diamond beads.

Dec 6, 2010