Search Documents

By Ketteridge IB, Mulcahy DE, Quast KB

The long term energy demands in South Australia are such that there is a distinct possibility that one of the lignite deposits in the State will be exploited to feed a pulver- ised-fuel power station. Bowmans lignite deposit is the largest lignite deposit in South Australia and is considered to be a contender. The deposit is ideally situated (100 km north of Adelaide) but the quality of the lignite is poor (see Table 1). TABLE 1

Jan 1, 1984

A useful sampling device can be constructed using three movable flaps. One is moved between its two extreme positions as material is flowing past it; the other two are only moved while no material is flowing past them. Material commences to flow into a sample container as the primary flap is moved from right to left, continues to flow into the sample container as the primary flap is moved from left to right, and the flow is terminated as the primary flap is next moved from right to left. As for several other sampling devices, an argument that there is no delimitation error can be made on the basis that the sampler conceptually divides the stream up into discrete portions and takes a set of equally-spaced portions as a sample.

Jan 1, 2008

THIS instrument, depends on the principle that, over a short period, the surfaee of a porous substance from which a liquid is evaporating receives the same amount of heat by conduction, convection, and radiation as it loses in the latent heat of the evaporating liquid. If, then, the amount of heat being received by a surface can be measured, the rate of evaporation can also be obtained. The Kata thermometer is also based on this principle differently applied.The instrument, as shown in Fig. 1, consists essentially of a thermometer with a sliding which is divided by three pointers into two equal parts which may be spaced so as to cover a distance of, for example, 5° of the thermometer scale. The instrument is calibrated so that the amount of heat required per unit area of the bulb to raise the menissus is known. The method of using the instrument is as follows:The slide is first set so that thc central pointer is at the temperature of the evaporating surface.The thermometer is cooled by any convenient means so that the meniscus is several below the lowest pointer. The thermometer is then placed near the evaporating surface, when the Ineniscus begins to rise and the time taken for it to rise from the lowest to the top pointer is measured. From this and the calibration results the amount of heat retained per unit area of the bulb at the mean temperature...

Jan 1, 1928

A static equilibrium mathematical model of the lead,flotation circuit at The Zinc Corporation Limited is developed to permit the feasibility of applying computer control techniques to be studied. The model is based on the relationship between the cumulative recovery of a mineral species R from n flotation cells or assemblies in a unit given asR = M(1-(1 - p)?)where M is the maximum possible: recovery and p is the probability of flotation for the particular mineral.The verification of this relationship by data from pilot plant cell-to-cell and plant open flow flotation units shows that these systems behave as if the probability p is constant for each cell or assembly of anyone unit. It is also concluded from this study that mineral recovery is independent of the head assay. Two consequences of this probability relationship, are demonstrated.1. The total recovery from an open flow unit is enhanced by increasing the number of flotation assemblies but maintaining a constant flotation time and total air addition.2. The rougher and scavenger capacity required to recover a bulk lead-zinc concentrate is approximately half that used for selective flotation.The static equilibrium model is derived by solving a series, of mass balance equations which incorporate the recovery-probability relationship for each type of flotation unit. It is used to calculate the complete metallurgy of the circuit for any arrangement of cells knowing only the plant feed assays and the probabilities of flotation for the three mineral types, galena, marmatite, and gangue for rougher, scavenger, and cleaner flotation. The high degree of prediction obtained is demonstrated by comparison with plant results.Pulp flowrate is the principal variable affecting the accuracy of the present model. Work is in progress to establish this effect and permit the derivation of a dynamic model. Even so, the static model is valuable in its present form for the analysis and design of circuits, and optimisation studies using computer services have been conducted.

Jan 1, 1964

The society in which we live is one of change, and we professionals are part of that society. The importance of this simple and obvious statement is often overlooked. My Presidential Address examines the question: can professionalism survive in our changing society?There is ample evidence to show that our society is changing, and that the rate of change is exponential. This rapid and accelerating rate of change is what Alvin Tomer refers to as "future shock". Rapid change means that we do not have time to become accustomed to what is happening around us and to feel comfortable with it; the greater the rate of change the greater the discomfort. The effect that this has on people is varied; the change may be either expected or totally unexpected.The rate and extent of change in society is not the same for all countries nor for all industries or occupations. Change is more rapid in Japan, Korea or Taiwan, than in Australia. It is more rapid in our cities than in the bush, more rapid for professional businessmen than for farmers. In our minerals and petroleum industries, we are still adjusting to the great changes that have taken place over the last fifteen years. In the past, products from our industries were sold on a free and open market. Today, mineral development and production in most undeveloped countries and some developed countries is manipulated for political, social and economic reasons. Changes of this nature have had a devastating effect on the operations of established mineral producers in the democracies.Because of the accelerating nature of change, we must recognise that the past is not a reliable guide to the future.Although extrapolation of the past into the future is a basic ingredient of commercial survival, extrapolation is less and less reliable.I borrow from others in quoting the Irish proverb: "The future is not what it was".The future is where our business lies and most of us at this Conference must endeavour to understand it and adjust to it. I believe in the old adage that:You can't know where you're going if you don't know where you've been and where you are at.There are a number of major factors which have created change within our social, economic, and industrial environment in recent years.

Jan 1, 1985

By C Young

The identification of Critical Risks, their associated Critical Controls, and the implementation of processes to ensure their ongoing management can be difficult and resource intensive. Answering the following Critical Risk Management related questions can be challenging: • What is a Critical Risk? • What is a Bow-tie Analysis and when should it be used? • What is Critical Control? • How is the effectiveness of a Critical Control assured, and how is this measured? • Who is responsible for managing Critical Controls? • What are the implications if a Critical Control is not effective? It appears that in the mining industry’s efforts to implement the Critical Control Management Process outlined by the International Council on Mining and Metals (ICMM), instead of embedding an integrated, well understood, value adding process, we have instead created a resource hungry monster that is poorly understood by numerous layers of the organisation.

May 5, 2022

In those days no one worried - there were plenty of other things to do. But in'these days it is different. Everyone worries- and. because there is so much worry, emotion has entered the picture. And, worse than that, capital is being made in political circles. People who were quite unaware, five years ago, that any problem existed, have now become experts on the subject, and shout to high heaven that something should be done - and yet they go on using the leaded high octane petrol they deplore so much. And even scientists, who should know better, adduce only such evidence as fits the argument in hand. And the Press is not without blame - some of its reportings is open to serious question, whatever may be the excellence of its motives. The point is made that one should know what one is talking about. And make sure that the evidence quoted is fact - and make sure too, that all the evidence is used, not only that which suita the argument.

Jan 1, 1971

Workplace Centred Learning, (WCL), is a learning strategy which helps organisations cope with the constant change in skill requirements that is part of business today. WCL focusses on the specific needs of the workplace and provides the structure and sets the standard whereby the required competencies can be transferred between individuals. Learning is considered part of the job and ownership is achieved by involving individuals in all aspects of the learning system. Each individual in a WCL system is considered both a learner and a teacher. A significant advantage of WCL over conventional training systems is that it responds quickly to changing requirements, and once in place, becomes self-sustaining. That is, once implemented, the system provides mechanisms to detect and respond to changes in skill requirements as they arise. WCL is a competency-based system with multiple levels of validation. It provides a flexible approach to skills development that recognises both the needs of the workplace and the needs of the individual. WCL was developed in collaboration with ALCAN Aust Ltd and is currently being implemented by companies within Australia and overseas.

Jan 1, 1995

The Central Extended Orebody is located within the Cracow Goldfield approximately 360 km northwest of Brisbane and approximately 220 km west of Bundaberg. It is an epithermal gold deposit hosted by the Late Carboniferous to Early Permian Camboon Andesite. The lode was mined by open cut methods and produced 170 458 tonnes of ore at 5.62 g/t gold.The geology of the rit is relatively simple, comprising two rock types, trachyandesite and rhyolite which have been sub-divided into several units. The trachyandesite is sub-divided into three rock types: brecciated trachyandesite which is the most widespread, hydraulically fractured trachyandesite hosts the mineralisation and the third sub-unit is chloritised hydraulically fractured trachyandesite and has no associated mineralisation. The mineralisation is confined to quartz veins in hydraulically fractured trachyandesite. Several phases of brecciation and subsequent quartz and quartz/adularia vein injection are evident although not all phases are mineralised. Two rhyolite dykes intrude the trachyandesite one is monolithic, the other is sub-divided into hydraulically fractured rhyolite (barren), silicified rhyolite and auto-brecciated rhyolite.

Jan 1, 1993

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

'Nothing happens until something is sold' This statement is not original - it is a necessary orientation for marketing industrial minerals. The most important single philosophy of marketing is that it recognises the consumer as the starting point. Production orientation is concerned with producing products that the customer might buy. Market orientation is concerned with finding the needs of the customer and how they can be satisfied. The difference between the two approaches can be recognised in company structures but the most tangible difference is in the approach by a company to selling and development. In other words, it is the market that decides what can be done with a mineral. The markets requirements dictate what mineral, what grade and what price will be paid. Therefore it follows that when pricing a product we should avoid taking the basic cost and arriving at a final selling price through a series of standard markups (unless government insists on it). We should start with the price the market can stand and work backwards to find out whether you have a profitable product or one that will fail because it is too dear. Naturally a thorough understanding of production costs is necessary particularly when marginal markets are concerned.

Jan 1, 1978

By R Miller, D Hawcroft

The business environment is never still and there has been enormous change in demand, technology and opportunity during the last decade. In order to succeed it is necessary for organisations to change the way work is planned, scheduled and carried out. This is necessary just to survive over time. The success or failure of the business is strongly influenced by people; the way they work, the way they are guided and their feelings about being part of both a team, as well as an organisation. Our Sustainable Integrated Management System (SIMS) philosophy is built on the belief that people want to be constructive and creative and it is their environment and working relationships that influence how their energies are directed.

Jan 1, 2000

The attachment of a spherical particle to a bubble is theoretically investigated under the condition of a mixed sorption coating of a collector. It is shown that the attachment is determined primarily by the hydrodynamic factor involving the displacement of liquid from the gap between a bubble and a particle. The dependence of the attachment on the state of the surface of particle (sorption coating) is due to a change in the boundary conditions on the interface with water both in the case of surfactant chemical sorption and in that of the physical adsorption of oil. It is demonstrated that at large distances the thinning of a interlayer is facilitated by a physically sorbed collector, while near the bubble this is done by a chemically sorbed one.

Jan 1, 1993

It is well known that in most areas of Central Europe it is not difficult to find water - usually at shallow depths - and to recover and use this water. What is much more difficult, however, is to find water sources that offer both sufficient in quantity and qual- ity. Far too often, there are sources that offer abundant quantities but of poor quality or vice versa, i.e. high quality water but insufficient volumes. In the former case where water quality is not adequate - which is more often than not due to anthropogenic factors and only very rarely a result of geogenic effects - the application of treatment techniques can help to turn such water into potable water that is suitable for human con sumption.

Jan 1, 1988

By C Pypno, P Nowakowski, T Opasiak, C

Belt conveyors are machines for continuous transport with most applications in mining industry in Poland. This is a result of simple construction and cheap operating costs. But conveying materials by belt conveyors are often in the powder state (eg small coal, gypsum, etc) and during the transport there is a possibility of polluting the environment around conveyor route. A good solution for this problem is the pipe conveyor, where a belt is closed on the route in circular shape and flat on unloading point. Another problem which is indicated in the paper is dusting on the belt conveyor boosters. In Poland a new solution of booster has been designed, whereby dustiness of transportation powder materials is reduced by up to about 90 per cent.

Jan 1, 2003

By W Stange

Assessing the risks in a mining project is a key aspect of project evaluation. This is an exacting and demanding task because of the complexity due to the need to deal with uncertainty over long time periods. The way risks are assessed and managed is critical to the long-term success of the projects and the business. Discounted cash flow (DCF) analysis is commonly used for project and risk evaluation. A discount rate is selected that accounts for uncertainties in the cash flows. However, it is difficult to determine an appropriate discount rate due to the large number of factors that need to be considered and the complex relationships between risk sources. Using a proven framework, ævalue at riskÆ (VaR), this paper proposes to rigorously model and quantify ærisk at sourceÆ. The approach was first employed to assess financial market risks and is now widely used in the banking sector for risk assessment. In project evaluation, all risk sources are identified and estimated separately to ensure the overall project risk is quantified accurately. A bottom-up approach has been proposed. Estimates are first carried out for risk factors at the bottom of the project structure. The assessment is then applied at increasingly higher levels until the overall project risk is estimated. Value at risk is a versatile methodology and can be used in a local or integrated manner. The final value is objective and the calculation steps can be easily justified and followed. Four case studies have been included to illustrate how the proposed approach can assist management in decision-making.

Jan 1, 2009

A method is proposed for the analysis of tin in cassiterite ores. Tin is volatilised by heating with ammonium iodide. The tin iodide so formed is extracted with hydrochloric acid and the concentration is measured by atomic absorption spectroscopy using an air-hydrogen flame.It is considered that a more efficient extraction of tin and faster reproducible results are obtained than by any other known method.

Jan 1, 1967

The BLEG (Bulk Leach Extractable Gold) technique is a semiquantitative measure of cyanide extractable gold contained in a sample. A 5kg sample is leached in cyanide solution for 24 hours and gold is precipitated out of the pregnant solution using zinc and assayed by AAS. The detection limit is reported as ppb (parts per billion). Telfer is located 1300km north north-east from Perth in the Great Sandy Desert. The climate is one of hot summers with irregular rainfall and mild winters. A large portion of the area is covered by aeolian sand and seif dunes with poorly developed drainage, rare outcrop; topographic relief is a maximum of 96m. Poor outcrop and poorly developed drainage render conventional stream sediment sampling and soil geochemistry inadequate. Therefore a technique providing a minimum number of samples with maximum accuracy and sensitivity was needed. Consequently BLEG orientation surveys were conducted over the Telfer Mine area in 1983, 1984 and 1985.

Jan 1, 1988

By Kandemir H, Stafford G

The Croydon Gold Mine is located in northwest Queensland and is a joint venture between Central Coast Exploration N.L. and Pancontinental Mining Ltd. The mining operation commenced in 1987 and consists of satellite open pit mines feeding a central Carbon-In-Pulp gold Treatment Plant. The gold mineralisation is hosted by quartz veins within the Croydon Volcanic Group and the Esmeralda Granite, a cogenetic igneous suite of Middle Proterozoic age. The mineralisation comprises gold and silver with associated basemetals. The gold and silver electrum occurs as extremely fine free grains. The gold distribution is heterogenous occuring across the full vein width, or restricted to the footwall or hangingwall. The average mineral resource grade is 3.5 g/t. The deposits are all hard rock and mining is carried out by drill and blast technique. All mining activity is carried out by a mining contractor. Mining is by a selective mining method which entails the drilling, blasting and extraction of the hangingwall waste prior to orebody extraction.

Jan 1, 1989

The mathematical modelling of rock fragmentation by blasting is one of the most difficult and challenging problems of applied mathematics. Not only is complex mathematics required but there is incomplete understanding of the basic physics and chemistry involved. The possibility of getting the physical basis of a model correct by simple mathematical and experimental procedures is demonstrated for the novel process of fragmenting rock by high-pressure arc discharges. While the importance of obtaining the correct physical basis for a model is emphasised, high-pressure arc induced fragmentation of rock is shown to be a powerful laboratory tool for the study of blasting.

Jan 1, 1990