Search Documents

The ERMS Process was developed during four years of testwork by Austpac Gold NL to overcome the severe metallurgical problems of the ilmenite atWestport, in the South Island. These deposits have been known for about one hundred years. They were originally mined for gold, and only later attracted attention as a possible source of titanium minerals.   The resource is of world scale and may exceed 20 million tonnes of contained ilmenite. Similar deposits occur at Barrytown further south and together these areas would constitute an important opportunity for export-oriented mineral development, if a viable beneficiation technology were available. Further processing is essential, as the composition of the ilmenite is well below market specifications.

Jan 1, 1993

By J Khosa, J Manuel

Iron ore sintering is very complex with many interdependent variables. For the same ores, the sinter quality and sintering performance may vary significantly with the scale at which the sintering tests are conducted. Therefore it is important to understand the effect of test scale on sintering performance and sinter quality while interpreting the test results. In this paper, different scales of iron ore sintering research at CSIRO are described and compared. This is followed by the results of two sinter blends tested at different scales. The results are compared and correlated to demonstrate the benefits of iron ore sintering research at the laboratory (4 g), small (5 - 8 kg) and pilot (55 - 140 kg) scales.

Jan 1, 2007

By Parsons AE, Lewis IE

Selenium is a minor constituent of the raw materials processed by the Cockle Creek smelter of Sulphide Corporation Pty. Limited. Certain proposed raw materials contain higher levels of selenium, and these will create a problem with regard to the composition of liquid effluent discharged from the smelter. A method has been developed for removing selenium from the smelter circuit by the sulphation of the fume collected in the Acid Plant electrostatic-precipitators. It is planned that by treating 10-20% of the total dust arisings there will be a substantial reduction in the levels of selenium reporting in effluents when treating selenium-bearing raw materials. The selenium is recovered in elemental form.

Jan 1, 1978

By H El-Shall, R Stana a

An innovative process for the separation of carbonaceous minerals from bulk ores is presented. In this process, the surface of carbonate minerals is reacted with acid used to nucleate CO2 bubbles at the particle solution interface. Entraining the liberated CO2 gas at the surface via coating agent renders the particle more buoyant providing for a selective separation from non-carbonate containing masses. Different surfactants were tested to stabilise the bubbles and float the particles. In this paper, separation of dolomite from apatite using PVA (polyvinyl alcohol) as a coating agent, is discussed. Interestingly, up to 10 mm particle sizes can be floated. Moreover, flotation of a phosphate and dolomite mixture was carried out and MgO content

Jan 1, 2005

By D R. van der Meulen, P Ande, D J. Lunt

Pressure hydrometallurgy is becoming an increasingly common unit operation in the treatment of gold and base metal ores and concentrates. The design of an adequate and appropriate pilot-scale testwork program is, therefore, essential in order to minimise the risks associated with developing a project in which autoclaves form a key part of the operation. This paper identifies the approaches that have been taken in the piloting of oxidative and pressure acid leach operations. Particular emphasis is placed on the determination of scale-up ratios between the pilot and commercial plants and the pilot-plant run durations. The issues, both metallurgical and project-specific, that can impact these key parameters are reviewed.

Jan 1, 2004

By Mould GR

Gas drainage has been practiced for many years mainly for safety reasons in various countries in Europe, in the U.S.A., the U.K. and Japan. Legislation has been developed to control the production, transport- ation and utilisation of methane and associated gases. Gas drainage is now being carried out at some Australian Collieries, but as this is a new venture little specific legislation is available. This paper briefly describes the drainage methods and legislation applied overseas, gives a brief history of gas drainage in N.S.W. and indicates the deficiencies of the present legislation. It outlines the approach to new legislation which will deal comprehensively with gas drainage operations and utilisation in New South Wales.

Jan 1, 1982

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

By Y Wu, F-J Ping

Today, coal production accounts for about 65 per cent of the nationÆs gross energy in China. By the year 2010, the output of coal is planned to increase to 1.65 billion tonnes and by the year 2020 to 1.9 - 2.0 billion tonnes. To meet these energy needs the Chinese coal industry is developing underground coal production on a massive scale. The new drive introduced by using direct torque control (DTC) is now proven technology for mine shaft hoisting. The drive offers unequalled speed and torque control performance as well as a low impact on the supply network by controlling the power factor to unity with a minimum of harmonics distortion.

Jan 1, 2005

Porgera is located in the Central Highlands of Papua New Guinea. Porgera Joint Venture treats a high grade epithennal gold deposit. Most of the gold occurs as submicroscopic particles in a sulphide matrix although there is some quite coarse free gold. Anticipated gold production is 900 000 oz per year for the first six years of operation.Stage I of the treatment plant consisted of a concentrator and leach/CIP Circuit. It was commissioned in August 1990. Design throughput was 1500 tpd with an anticipated gold recovery of 60 per cent. Throughput achieved was actually 1850 tpd with an average gold recovery of 69 per cent. CIP tails were accumulated in a pond awaiting retreatment by pressure oxidation.

Jan 1, 1992

Highwall mining commenced in the Appalachian region 50 years ago. With innovative equipment design introduced in more recent times, penetration distances over 300 m are now commonplace. It is only in the last three years that highwall mining has become part of the Australian coal industry. Geotechnical evaluation is an integral part of the Australian procedures, and although still being refined, has already proven its worth. Statutory guidelines have also been prepared for operations in Queensland. This paper explores trends in equipment design, geotechnical prediction, operating techniques and statutory requirements with regard to highwall mining Australia's coal deposits. A quick assessment guide to assist in the evaluation of potential sites is included.

Jan 1, 1992

By McLeod RL

The Mt. Morgan mine, located 36 km SSW of Rockhampton, Qld at Lat. 23¦38' S, Long. 1500 22'E, is hosted by a Middle Devonian sequence of acid volcanic rocks and sediments. The Upper Nine Mile Creek (UNMC) prospect, 14 km SE of the Mt. Morgan mine, is in an ap- parently equivalent sequence of rocks. The Late Devonian Mt. Morgan Tonalite separates the two areas. The Mt. Chalmers mine, located 27 km NE of Rockhampton at Lat. 23¦ 18' S, Long. 150039'E, is hosted by the Early Permian Berserker Beds. These three volcanogenic massive sulphide deposits show pronounced similarities in their host rock lithologies and stratigraphic-struc- tural settings.

Jan 1, 1987

The only functional underground Coal Mine in Nigeria is located in Enugu in Anambra State. For some years now the mine has been beset with a perenial problem of flooding. This has hampered produc- tion and some time ago the mine was abandoned. Recently money and equipment were made available to reactivate the mine. Attempts are now made to increase production as it is very much below demand. However, there are problems as the mine is below the water table under some major rivers and any advance exposes men and equipment to water surge. The paper traces the different attempts made to dewater the mine and the problems encountered in producing coal in this mine.

Jan 1, 1988

Geomorphology is one of the most basic elements in geographic enviroments. Geomorphological mapping is significant in the spatial distribution of representing land form and understanding various features of geomorphology. Geomorphological mapping began very early in China, as the map, showing conekarst(karst pinnacles) of Juiyishan, Hunan province, it was drawn in 168B.C., which was excavated from Han tomb. Mawangdui, Changsha. Its original idea of map-making is rather similar to that of modern map and could undoutedly be the oldest map of tropical karst discovered in the world.Before liberation, landform mapping was done piecemeally and only a small number of maps were prepared by a few editor as insets.

Jan 1, 1990

By Lye GN

Rock mechanics investigations have shown that some major slopes in the Panguna pit would be stable at angles in excess of 500 providing near-surface instability could be controlled. Excavation of final batters at angles between 55¦ and 60¦ is now being carried out using D10 dozers with berms at 45 to 60 m centres. A trial slope with berms at 90 m centres is planned. Shotcreting of weak zones combined with crest reinforcement, with rock anchors and dowels, is used to provide protection against erosion and toppling of the crests. Overall slopes excavated in this way are of the order of 10¦ steeper than slopes obtained by blast and shovel excavation.

Jan 1, 1986

Three methods of gold analysis are briefly described highlighting some of the problems and advantages of each. The variation of results between samples and splits and due to method preparation are illustrated. The mean percent difference of the fire assay values from the means of sample split values for three cases is 15%. Finally, a comparison of the aqua regia atomic absorption spectroscopy and fire assay fusion AAS techniques is made. This shows that the mean precision, the ability to obtain the same value, of the methods at 98% confidence are +30% and +15% respectively. The fire assay fusion atomic absorption spectroscopy method is relatively more accurate than the aqua regia method.

Jan 1, 1982

By Geoff Baldwin

The use of monitors to assess equipment performance is carried out on a routine basis in many industries. The benefits gained through process control in knowing exactly how the equipment is working far outweigh the initial capital costs of the monitor. In the mining industry several dragline monitors have been developed and installed on equipment through out the world, but to date none has been fully accepted by the industry. This paper describes the use of a sophisticated monitoring system which incorporates an onboard processor to assess both dragline and blast performance. The results of a case study are presented and an indication of the potential of the monitoring system to optimise mine production is given.

Jan 1, 1990

The economics of gold differs from that for base metals mainly because a large component of gold demand is investment or stock demand whereby the metal is purchased and stored for monetary or anxiety motives rather than fabricated into industrial products.The second major component of gold demand is fabrication, principally into jewellery but also, to some extent, into industrial products.Supply to the Western private- gold market comprises non-Communist mine production, Communist sales (chiefly from the USSR), and, finally, net sales by the Western Central Banks, which have total stocks of about 35,000 tonnes and which are sometimes net buyers as well as sellers.The different components of demand and supply fluctuate from year to year.

Jan 1, 1984

By Denholm W. T

The SMELT-2 package is specifically designed to perform on-line simulation of smelting processes. This paper describes its application to the simulation of continuous matte converting followed by reductive slag cleaning in SIROSMELT reactors. The matte, containing 50% Cu is assumed to be produced at the rate of 20 tph in a continuous matte smelting furnace such as an Outokumpu Flash Furnace, Noranda or Sirosmelt reactor. Two alternative fluxing strategies in the converter are examined, namely: ò conventional silicate slags, ò calcium ferrite slags, and the flow sheets associated with each strategy are discussed. A regular solution model is used in the present study to account for the variations in the activity coefficients of components in the slag.

Jan 1, 1989

The first stage in the refining of lead blast furnace bullion is the removal of copper and this is normally done as a batch process in open kettles,A number of attempts have been made in the past to establish fontinuous processes operating in reverberatory type furnaces, but the growth of accretions in the furnace has always presented a serious problem.This has been overcome in the plant of the Broken Hill Associated Smelters Pty Ltd at Port Pirie by the construction of a reverberatory furnace and ancillary cooling system of novel design.Although a number of mechanical and metallurgical problems still remain to be solved, it is claimed that a workable continuous copper drossing process has been established.

Jan 1, 1963

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981