Search Documents

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

With the sinking of the new No. 3 Shaft and the increasing depth and northward movement of the mining operations, improved ventilation of the mine workings became necessary and it was decided to sink a new upcast ventilation shaft midway between No. 2 Shaft and No. 3 Shaft.The shaft is finished to 16 ft. internal diameter and connects with the mine workings at the 2,600-ft. level. It is lined with unreinforced Concrete approximately 12 in. thick. The shaft sinking routine was drilling, blasting and mucking by hand using a 27-cub. ft. capacity bucket. The concrete lining was poured in conjunction with the sinking and was normally finished within 30 to 50 ft. of the shaft bottom.

Jan 1, 1957

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

The Sydney Coalfield, Nova Scotia contains extensive undersea longwall mining operations which are expected to continue well into the 21st Century. A long term research program has been initiated by the Cape Breton Coal Research Laboratory to investigate the full spectrum of problems associated with undersea mining and develop specific guidelines for use by the mine operator. At present, research is centred on the detailed evaluation of existing undersea sub- sidence guidelines, the identification and development of instrumentation capable of moni- toring seafloor subsidence profiles and the effective sealing of offshore exploration boreholes. In addition, work is also planned to examine in situ strata permeability changes occurring between the mining horizon and seabed and the feasibility of using artificial islands.

Jan 1, 1986

By Osborn G

The bulk flotation behaviour of an industrial rougher bank has been determined with a view to characterising the size iepend ent behaviour of the identifiable nineral groups present. A relatively simple flotation model, based on first order kinetics and the assumption of perfect mixers in series ias been used to provide a fit to the operation of the cells. The adequacy of the model is discussed in relation to the characteristics of the ore and the size iependancy of the parameters. It is shown that improved fits are possible if the model accounts explicitly for this size dependancy and demonstrated how the model may be of use in prediction of the grade recovery relationships for different operating conditions as an aid to plant optimisation.

Jan 1, 1986

By Lovitt M

Ora Banda Gold Mine is located in the Eastern Goldfields of Western Australia. Mining is carried out underground by sublevel open sloping resulting in large open stopes. A Mass Blast of approximately 250 000 tonnes was carried out in July 1994 to recover a rib pillar between two stopes, and the crown pillar between the underground mine and the abandoned open pit above. Strategic development within 50 m of the blast consisted of two ventilation shafts and the main decline. This development required careful design and prediction of the blast results. This paper describes the design of the blast, the prediction of the likely effects, the measures taken to reduce the risk to important development, and the results of the blast.

Jan 1, 1995

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By Hoskings AD

Bolting forms a prestressed elastic layer of rock which is capable of supporting loads at right angles to the bolted surface. Investigations on rock bolting made with a number of different models give rise to empirical and theoretical prin- ciples for the formation and action of the layer. In the models, flat and arched layers of many materials were used simulating rock conditions ranging from closely interlocked blocks to fragments of various shapes. Results of observations made in the underground works of the Snowy Mountains Scheme are related to the mode of action of bolted surface layers of rock. There is abundant experimental, theoretical and practical explanation for the well-demonstrated capability of bolting as a means of rock support.

Jan 1, 1971

The paper poses certain questions relating to mine design aspects of deep shaft pillars. It then explores these questions in relation to Western Deep Levels (South) where a sub-shaft system is to be sunk to 4 000 metres below surface to exploit two narrow tabular reefs in the down dip extension of the mine workings. After brief discussion of some broad considerations, the findings of a major rock mechanics investigation are reviewed. Some overall conclusions as well as the outcomes of separate studies of the anticipated behaviour of shaft pillars on each of the two reef horizons are outlined. The effect of this behaviour on the barrels of the shafts in the system and on the associated shaft excavations and in-pillar development is Cnnctdarcrl

Jan 1, 1986

Coal washing practice can be improved not only by critical examination of the plant being operated but also by studying plants operated in other areas. The developments at the Australian Iron & Steel Pty. Ltd. plants are discussed in relation to experiences there as well as developments which have taken place in Queensland in recent years. Early A.I.S. problems involved small coal cleaning in heavy medium cyclones and flotation. A proposed future plant flowsheet for A.I.S. is considered in the light of these experiences. Reference is made to plants operated by the Thiess, Peabody, Mitsui Coal Company Pty. Ltd. at Moura and the Utah Development Company's plants at Blackwater and Goonyella in the development of coal washing prac- tice in Australia.

Jan 1, 1975

The law relating to the Treaty of Waitangi is developing rapidly at present. A number of separate, but related, developments can be identified.

Jan 1, 1988

By M H. Randell, J B. Haines

The Honeymoon Uranium Project comprises the Honeymoon Deposit,Goulds Dam Deposit and Yarramba Prospect in the Southern Lake Fromeregion, South Australia. Both the Yarramba Prospect and HoneymoonDeposit (which includes Honeymoon and East Kalkaroo orebodies) arelocated in the Yarramba Palaeovalley. The Goulds Dam Deposit is about75 km north west of Honeymoon, in the Billeroo Palaeovalley. Exploration for sediment-hosted uranium began in the area in the late1960s, culminating in the discovery of Honeymoon and Goulds Dam inthe early 1970s. In 1982, a 25 L/s demonstration plant was built atHoneymoon to confirm suitability for in situ leaching. The project was put on hold in 1983 due to changes in government policy. Southern Cross Resources Australia Pty Ltd acquired the project in mid 1997. Roll-front deposits form from a migrating geochemical cell, anadvancing reduction-oxidation interface between oxygenateduranium-bearing groundwater and its reduced aquifer host. The source of metal is uranium-anomalous granites, which were eroded fromsurrounding ranges. The weathered granites and resultant sediments are stripped of uranium by oxidised groundwaters, to form solutions carrying uranyl carbonate complexes. The solutions percolate down-slope through permeable sand zones until contacting a reduced environment where uranium precipitates. Uranium mineralisation occurs interstitially between and as thin coatings on sand grains, usually in the form of uraninite or coffinite. The palaeovalleys (previously termed palaeochannels) are incised intounderlying Cambrian/Precambrian basement rocks and filled withsemi-consolidated, largely un-cemented, Tertiary sediments of the Eyre Formation. The late Palaeocene to middle Eocene Eyre Formation is the basal unit of the Tertiary succession in the Callabonna Sub-basin of the Lake Eyre Basin. Further to the north, the Lake Eyre Basin overlies the Jurassic-Cretaceous Eromanga Basin, which comprises much of the Great Australian Basin. Eyre Formation sediments are in turn overlain by the late Tertiary Namba Formation and terrestrial Quaternary units. At Honeymoon, the Eyre Formation includes immature, pyritic,carbonaceous sands and gravels interbedded with lignite andkaolinite-illite-montmorillonite clays. It was deposited by braidedstreams during epeirogenic uplift of the Olary Ranges, accompanied bysubsidence of the Lake Eyre Basin. The Eyre Formation comprises aconsistent stratigraphy of interbedded sand and clay units that arecontinuous over the Honeymoon Deposit but with local variationindicating some hydrological connection between aquifers.In the Honeymoon orebody, uranium occurs within coarse-grained,pyritic sands where the basal sand pinches out between overlyingcarbonaceous clay and the southern palaeovalley slope. Its characteristics are typical of the well-developed, planar limb of a roll-front uranium deposit. Zonal changes related to the reduction-oxidation interfaces across the deposit are readily observable. The orebody extends for nearly 1000 m along the valley margin, is 400 m wide at its maximum and averages about 6 m in thickness. The East Kalkaroo orebody also lies near the southern margin of theYarramba Palaeovalley. It extends discontinuously for approximately 3.5 km and averages 200 m width, with significant uranium present in the Middle as well as the Basal Member. The Billeroo Palaeovalley extends northward for 40 km sub-parallel tothe western side of the Benagerie Ridge, is up to 5 km wide and hasgently dipping banks. Eyre Formation within the palaeovalley isconcealed beneath 90 m of Quaternary and Namba cover, isapproximately 40 m thick, and is sub-divided into three upward-finingunits, which are remarkably similar to the Yarramba Palaeovalleysequence.

Jan 1, 2001

By T J. Sprott, Associates

A number of people have expressed concern, understandably, that if mining operations take place in the Coromandel, the flows of mineralised ground water which exist will be intercepted. This water in many cases contains toxic metals including mercury, arsenic and lead and it is thought that if this water is allowed to enter streams or the waters of the Hauraki Gulf, it could endanger natural marine life and possibly established fisheries. This paper seeks to explain in simple terms the geology and the process of deposition of the various mineral deposits in the ground, the chemistry of the reactions between these minerals and the rain water falling on the ground, the hydrology and behaviour of this mineralised groundwater as it moves through the ground until it eventually enters the sea.

Jan 1, 1981

By C Ross

This paper uses the results of research trials by Landcare Research and Forest Research Institute and assessments of reclamation plantings at mines and other drastically disturbed sites to describe methods of enhancing restoration of native forests. The characteristics of mine and forest environments are compared to highlight the difficulties facing restoration and techniques which result in successful restoration are described. Selection of the most appropriate technique is illustrated by describing restoration of lowland beech-podocarp forest at a West Coast coal mine. The key to successful reclamation is to understand the factors controlling and limiting plant establishment and growth, then to design rooting media, surfaces and management regimes to create a favourable environment. This paper concludes with a summary of the planning and technical factors which are critical for successful restoration of native forest.

Jan 1, 1995

Gold mines produce unique water treatment requirements. This paper focuses on case studies of innovative processes used for treatment of water resulting from gold mining and processing. The case studies include treatment of mine dewatering water for beneficial application from an Australian gold mine, Bendigo Mining, as well as treatment for arsenic removal of tailings water from mining and processing at Goldcorp mines in Canada. Gold mining can often require dewatering to prevent groundwater seeping into and flooding the mine workings. Gold mining and processing often accumulate wastewaters in a tailings dam. The mine water can contain contaminants such as dissolved salts, iron, arsenic, manganese, heavy metals and odorous sulfates. Environmental discharge requirements as well as community needs for water drive mine operators to consider the most appropriate water treatment process. Treatment of gold mine water can require processes including oxidation, pH adjustment, coagulation, flocculation, clarification, further oxidation/adsorption of specific metals such as manganese, filtration, salt reduction utilising reverse osmosis, brine minimisation and other innovative technologies. These processes are discussed through the case studies with examination of the specific treatment process that is required. This paper uses real case studies of gold water treatment processes to explain and examine the technology and the reasons for designing specific processes. The focus is toward explaining innovative processes where the water is used for sustainable environmental discharge or treatment to a quality that can be beneficially used by the local community.

Jan 1, 2007

By C Ferron, R Massimi

There is approximately 240 000 tonnes of arsenic trioxide dust stored in underground chambers at the Giant Mine in Yellowknife, Northwest Territories, Canada. To minimise the amount of arsenic released to the environment, a number of closure alternatives are being considered. One alternative is to mine the dust, encapsulate it and dispose the mixture into a secured landfill. The potential leaching behaviour of the encapsulated dust was examined in a laboratory programme. Cylinders of arsenic trioxide dust mixed with cement/aggregate and bitumen were prepared. The dust content varied between zero per cent and 60 per cent of dry weight charge. The cement cylinders were tested for strength, leaching and freeze/thaw durability. The bitumen cylinders were tested for leaching only. The results show that increasing dust content in the cement cylinders negatively impacts the strength and the freeze/thaw durability of the samples. A contributing factor is likely the high water to cement ratio in the samples. Leaching tests show that arsenic release from cement cylinders increase with increasing dust content. Arsenic concentrations in leachates do reach a plateau at a certain point in time. Arsenic release from bitumen cylinders was significantly lower compared to cement cylinders. Arsenic concentrations eventually were less than 0.05 mg/L in samples containing up to 25 per cent arsenic trioxide dust. Arsenic leaching rates were found to decrease by an order of magnitude over the course of three months.

Jan 1, 2003

By G Hayes

Ore from the Browns deposit near Batchelor, in the Northern Territory of Australia, is a fine-grained polymetallic sulfide ore hosted in graphitic black shale. Minerals of economic significance are seigenite (Co,Ni)4S3, Galena (PbS) and Chalcopyrite (CuFeS2) with minor Sphalerite (ZnS). Gangue minerals include quartz, carbon and K-feldspar. The grain size is fine, with a significant amount of the seigenite present as Early flotation work determined that a grind size of around 20 microns was required to achieve clean sulfide concentrates. This work recommended oil agglomeration flotation, in which small sulfide minerals were collected, then loosely agglomerated with oil ahead of flotation into a heavily mineralised froth. In the 400 kg/hr prototype plant this froth proved unmanageable. A conventional flotation circuit after grinding to a P80 of 24 microns and using very low flotation pulp densities resulted in an 86 per cent cobalt recovery.The paper analyses further laboratory work which has increased cobalt recovery to 91 per cent by grinding to û250 microns ahead of flash flotation. The real cobalt recovery breakthrough comes from flash flotation of the whole mill discharge rather than the more usual flash flotation of cyclone underflow. Flash flotation tailings are ground to û38 microns and are floated under normal flotation conditions with only the scavenger concentrates being reground to 20 microns.A one tonne per hour prototyping campaign is scheduled to demonstrate the robustness of this circuit.

Jan 1, 2002

The New Zealand Minerals Industry Association was incorporated as the NZ Mineral Exploration Association in 1982, with a membership that consisted of the gold exploration companies then active in New Zealand . As its membership broadened, it changed its name to the Mining and Exploration Association in 1994, and more recently the Minerals Industry Association. It is a non-profit-making incorporated society relying on voluntary membership, and is not funded by industry levies.   It has employed a full time executive director since 1988 when Robyn Ross was appointed, followed by John Pfahlert (1991 - 1996) and now with Doug Gordon managing the Association.   The Association is one of a number of organisations that represent the mining industry in New Zealand. Others include the Coal Association of NZ (CANZ), the Aggregate and Quarry Association (AQA), The West Coast Commercial Gold Miners Association and Minerals West Coast.   NZMIA membership comprises the main exploration and mining companies that account for over 80 per cent of New Zealand Æs mine output, and nearly all of its exploration investment. Its membership has expanded from gold exploration to encompass exploration and mining companies active in coal, gold, aggregates and industrial minerals.   The Association has developed a National Minerals Strategy that determines its priorities, implemented via a Minerals Industry Advisory Committee. This group was established six years ago to advise the Associate Minister of Energy on issues relating to the long term development of the minerals sector in New Zealand.

Jan 1, 2006

By M E. Taulis, S Hayton, D A. Manhire, J G. Pope

Successful development of coal seam gas (CSG) resources in low-rank coalfields such as the Powder River Basin has raised interest in CSG from low rank coal in New Zealand. Kenham Holdings Limited holds 12 Petroleum Exploration Permits (PEP) covering some of New ZealandÆs low-rank coal and lignite resources and has engaged CRL Energy Limited to assist in the systematic evaluation of the CSG potential of the permits. To date, exploration results from seven New Zealand coalfields reflect differences in coal type, rank, depositional environment and depth of burial between coalfields. Several of the explored coalfields are considered prospective for CSG. One of the most advanced Kenham exploration programmes is in the Hawkdun Coalfield, Central Otago.   The Hawkdun Coalfield contains a single, thick lignite seam with properties that are similar to the Powder River Basin. Preliminary results indicate the Hawkdun Coalfield is prospective for CSG with the potential to contain between 25 and 60 PJ of gas; enough to supply a 30MW power station for ten to 25 years. Further drilling is planned to investigate the economic viability of the Hawkdun Coalfield. The in situ permeability of the lignite, the amount and availability of free gas, gas saturation at depth and market opportunities will determine its economic viability. If initial pumping and production results in the planned exploration programme are promising, the Hawkdun Coalfield will be further developed with additional production drillholes to form a trial production pod.

Jan 1, 2004