Search Documents

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

With the recent increase in the number of underground secondary sulphide dust explosions in Canada, Australia and elsewhere in massive sulphide ore mining industry, establishment of quantitative and realistic methods of analyzing the mine dust is of paramount importance. This paper examines and analyses dust samples from a mine area that has very recently experienced sulphide dust explosions. Also, it attempts to evaluate the physical and chemical characteristics of the dust. Explosibility of the dust samples was determined by quantifying the oxidation reaction of the sulphide dust particles in a 1.2 L, Lindenberg open horizontal tube furnace. Percentage sulphur', % S oxidised during ignition of a dust sample of known assay, % S and dust concentration (g/m3) were determined by the quantitative chemical analysis of SO2 gas produced during the oxidation reaction. A dust sample with high sulphur content, 22.3% S (assayed) and mean particle size 9.82 pm, was found to exhibit a low degree of oxidation compared with a sample of low sulphur content, 15.44% S and mean particle size 21.7 tcm, at the same Temperature.

Jan 1, 1988

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

The Yilgarn Block of Western Australia presents (figure 1) a number of problems for conventional diamond exploration based on heavy indicator mineral sampling. These problems are due to the geology and unique geomorphological development of the Yilgarn Block.Essentially the Yilgarn Block is a pene- plain developed on a craton composed of Archaean intrusive granitoid rocks with meta- morphosed greenstone; which, apart from regional uplift, has not been tectonically disturbed since planation by glaciation in the Permian. Therefore since the early Plesozoic the Yilgarn Block has been subjected to terres- trial weathering conditions. Bettany et al., (1984) identify two phases of particular importance in the development of the present landforms: 1. Periods of lateritization during the Tertiary which result in the ~lassi~al laterite profile (figure 2). Duricrust indurated : Fe and Al oxides Mottled zone : Clay and Fe oxides Saprolite or pallid zone : leached clay grading into fresh rock. 2. Subsequent periods of aridity and semi- aridity during which laterite development was truncated and reworking of laterite Occurred.

Jan 1, 1988

By Brathwaite RL

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bear in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked tug, Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No. 2 level of the Golden Bar Mine. A fau I has downthrown the Golden Bar Mine section by 2 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It i composed of bands of milky "buck" quartz with thin laminae of schist. Scheelite occurs in short strings of grains withi quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.

Jan 1, 1995

By Martins V, Dunne R

A re-evaluation of the Hampton Boulder prospect in the early eighties resulted in a decision to proceed with mine development in December 1985. A 500 000 tpa gold treatment plant was commissioned in December 1986. The treatment facility was expanded to 1 600 000 tpa in July 1988. A tailings treatment plant to improve recoveries from harder gold bearing sulphide ores was built in December 1990. The development of an underground mine in 1991 meant that a source of sand for backfill was required. A sands plant to fulfil this requirement was commissioned during November 1991.As of June 1992 a total of 7 710 487 tonnes of ore have been treated through the New Celebration gold plant. Total gold production from inception of the new mine until June 1992 is 545 470 ounces obtained at an average recovery of 90.1 per cent from an average gold head grade of 2.4 g/t. The combined quoted ore reserves at the end of December 1991 was 14Mt grading 1.8 g/t gold

Jan 1, 1992

By D Craw

Interactions between structure and lithology in the Hyde-Macraes Shear Zone controlled the style of gold mineralisation at the Macraes mine. Large volumes of rock in some mine pits have most gold disseminated in hydrothermally altered schist, rather than in quartz veins. Mineralisation was initiated in the latter stages of metamorphism. Pods of massive schist rich in quartz and feldspar are surrounded by more fissile schist consisting of interlayered micaceous and quartzofeldspathic schist. Later shears have been partly controlled by the micaceous schist, and anastomose around pods of more massive schist. Micaceous schist was replaced by pyrite and arsenopyrite, accompanied by recrystallisation of phengitic muscovite under lower greenschist facies conditions. Gold occurs in sulfides and with microcrystalline quartz formed during minor silicification. Massive schist is locally mineralised along sulfidic microshears which have phengitic muscovite largely illitised under sub-greenschist facies conditions. Mineralised massive and micaceous schists were overprinted by cataclastic shears, with addition of graphite and more sulfides. Mineralisation occurred during a transition from ductile to brittle deformation regimes as the schist was uplifted in the late Jurassic.

Jan 1, 2004

By Liu Y

Mathematical modelling of scrubbers in development and longwall operations in underground mines produces useful results. Mathematical modelling on the mounting of scrubbers on longwall supports shows that the number of scrubbers and the air quantity through the scrubber are the two important parameters. Increase in both these parameters results in decrease in dust levels at the tail gate. The critical factors are scrubber efficiency and the ratio of the air through the scrubber/total air quantity.Results of parametric studies conducted to establish factors which have dominant influence on the effectiveness of the scrubbers on dust levels and high gas build-up in the scrubber show that for use of scrubbers in development headings, the order of importance of parameters in relation to dust concentration in the scrubber area is: scrubber efficiency, rate of production, specific dust make/tonne, leakage factor, intake dust concentration, recirculation factor and air quantity through the scrubber.The equations developed for mathematical analysis and the detailed results of modelling provide useful data on recirculation of emitted gas in the use ofscrubbers for dust control.

Jan 1, 1995

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By Coppock BW

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By A Black, J H. Youngson

At least 85 000 tonnes of mine tailings were discharged into Deepdell Creek, east Otago between 1890s and 1940s. The tailings contained about 1 wt % arsenic, so about 850 tonnes of arsenic in the form of arsenopyrite was discharged. Annual floods have removed nearly all tailings within c. 60 years. Small amounts of arsenic-bearing sediments (<250 ppm) remain in Deepdell Creek. About 7 kg/year dissolved arsenic was discharged in groundwater from mineralised Hyde-Macraes Shear Zone rocks in the vicinity of the historic mine sites. Adsorption of this arsenic on to iron oxyhydroxides in the stream sediments may have contributed to the elevated As content of those sediments. Even less arsenic remains in the main Shag valley below the Deepdell Creek confluence (15 - 25 ppm As). Rare relict arsenopyrite grains are trapped in bedrock crevices 25 km from source. No tailings deposition is detectable in theShag River estuary, and the tailings have presumably been discharged into the sea. Natural rehabilitation of the Shag catchment has been rapid and effective.

Jan 1, 2004

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By Wilson AF

Gold-silver mineralization at Cracow and Ukalunda in Queensland comprise quartz-filled veins, fissures and breccia zones hosted by propylitically altered volcanics and epizonal intrusions which are strongly fractured. The terrestrial volcanic facies, structural setting, type of alteration and complex mineralogy suggest these deposits are of the epithermal type.The 180 depleted character of the wall-rocks is consistent with the involvement of meteoric waters in convective hydrothermal cells associated with the vulcanism. The Cracow quartzes have remarkably low 6180 values from -2.0 to -3.4 per mil typical. of meteoric hydrothermal systems at high latitude, consistent with the inferred position of Australia during the Permian. 6180 values for the Ukalunda quartzes exhibit a wide range from 5.1 to 14.9 per mil which reflect the mixing of magmatic and meteoric waters, and a steep geothermal gradient.Further stable isotope and geochemical studies are in progress to establish the scale and morphology of the zones of anomalous 6180 and mineralogy in the wallrocks which constitute significant exploration targets.

Jan 1, 1984

By Mauk JL, Arehart GB

Quartz veins from the Martha Hill epithermal gold-silver deposit, Waihi, commonly exhibit crustiform banded textures. Visual differences observed between bands are primarily the result of a 1 to 1500 ¦m variation in quartz grain size. Quartz band textures are dominated by anhedral interlocking quartz mosaics, commonly associated with minor adularia and sulfide phases; these textures are interpreted to be products of amorphous silica crystallisation. The occurrence of rhombic adularia suggests that prolonged boiling influenced parent fluids. In contrast, the presence of coarsely crystalline bands, made up of subhedral to euhedral quartz grains, infers primary crystal growth from solution; evidenced by the occurrence of growth-zoned quartz within these bands. There is a narrow range of 3.3%o in 618Oq,,,,,= between maximum and minimum isotopic values for the deposit. Significant overlap in 618Oqu,, values are observed between the Martha and Welcome lodes. However, statistically significant and commonly systematic differences do occur between individual bands analysed in most samples. Temperature fluctuations may be the dominant factor responsible for observed inter-band variation.

Jan 1, 1995

The mIning operations of Bougainville Copper Pty. Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea.C.R.A. Exploration Pty. Limited first established mineralization in the Panguna area in 1964. Exploration work since then has established ore reserves estimated to be 900,000,000 long tons of ore assaying 0·48 per cent copper and 0·36 dwt/ton gold. An economic feasibility study completed in July, 1969 enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons/day. The concentrate will be pnmped as a slurry through a 16 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 MW steam power station, and access roads.

Jan 1, 1971

By Singh JK, Singh R

With a view to producing increased target output every year, Indian coal mining industry is fast moving towards mechanisation but the present approach of mechanisation suffers from lack of standardisation, mainly due to nonavailability of the cutting data for various machine/rock combinations. The coal seams of the country are relatively hard in nature and the coaling machines are reported to be affecting production and productivity of the coal mine and the very trend of niechanisation. This paper presents the result of extensive study performed to visualise the cutting characteristics of coal seams of compressive strength ranging from 20 MPa to 65 NIPa. In a specially designed drag bit type coal plough rig, continuous recording of cutting forces was done with the help of a microprocessor based data logger and the specific energy of cuttability was evaluated at different depth of cut and speed of cutting. The geomechanical properties such as compressive strength, orientation and frequency of cleats etc. and different indices of coal seams were measured in the laboratory and field and relationship was developed for easy determination of specific energy.

Jan 1, 1992

For some time fine coal (-0.5 mm) flot ation has been considered as a bulk flotation problem. Combinations of hydrocarbon oils and frothers have been used as surface active agents in coal flotation. The selectivity of the flotation process has always been poor in such cases. With the increase in fine coal production due to mining methods and coal handling systems, optimisation of fine coal treatment.has become important. Petrographic and mineralogical composit- ions of coal particles have been reported to influence their flotability. The problem becomes more complex due to surface oxidation of coal and the presence of slime forming clay minerals in the run of mine coal. In this paper, the flotation problem is examined on the basis of various constituents of coal and their associated gangue minerals. The selection of reagents has been suggested on the basis of their surface chemical properties. Factors such as surface modific- ation of coal and gangue materials, flotation kinetics and hydrocarbon oil - coal inter- action have been critically evaluated to improve fine coal flotation recovery.

Jan 1, 1978