Search Documents

By J Samosir, L Snyman

Northparkes was the first mine in Australia to use block cave mining method which relies on gravity and natural rock stresses to fragment and recover the ore. It was also the first hard rock mine to use hydraulic fracturing, in conjunction with CSIRO, to promote caving of E26 Lift 1. The technique was later used on E26 Lift 2 wedge and E48 prior to undercutting.Northparkes production is currently sourced from the E48 Lift 1 block cave mine and E26SLC. The E48 block cave contains economic ore to the north and south of the current cave footprint. To recover this ore the footprint has been extended on the north and south with two extraction drives and one extraction drive, respectively. Modelling of cavability above the additional drives indicated that the cave would not readily propagate to a sufficient height of draw to mobilise the ore and tended to arch over into the existing cave. To address the modelling results and to reduce the risk of the project, rock mass preconditioning was adopted.This fracturing campaign was performed from surface drill holes adjacent the subsidence zone angled to intersect the higher grade and higher elevation ore zones.Optical televiewer surveys, run prior to fracturing, picked intervals and fault zones to be avoided. Holes were resurveyed post-fracturing to detect newly created fractures and as a measure of success of the program.During fracturing operations water and gel fractures were run at varying depths and pumping pressure was logged for each fracture. The mine seismic system monitored significant events and dye in the fluids utilised for tracking water inflow locations during underground inspections.Towards the end of the project, guar fibres from gel were detected within the mill circuit and required treatment to resume optimum processing.CITATION:Webster, S, Snyman, L and Samosir, J, 2016. Preconditioning E48 cave extension adjacent to an active cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 471–478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

THE treatment by chlorination of the Mount Morgan Gold Mining Company's ores was first accomplished, early in 1886, by a works having a capacity of 25,000 tons per annum. Shortly afterwards another works was established, capable of dealing with 50,000 tons per annum. The extraction of gold was originally successful and satisfactory, but running expenses were high, averaging £2 19s. 6d. per ton of ore treated. These works were believed to be the largest chlorination pJants in the world at that time. As might have been expected, the mechanical details and chemical process had not been perfected, and, moreover, both works were hurriedly built, and operating expenses were not then considered of such prime importance, as the ore at that time was of very high grade the large quantities of low grade ore since dealt with not being then considered, since the bulk of it was not even known to be in existence.These two works consisted of lock-breakers, high speed rolls, screens, elevators, &c., for crushing; a large number of small handrabbled reverberatory furnaces for roasting; one-ton chlorination barrels and three-ton leaching vats for chlorination.

Jan 1, 1910

By Clifford C. E

1 eat my peas with honey I've done it all my lifeIt makes them taste rather funny But it keeps them on the knife.Innovation is that elusive characteristic which involves the determination of multiple and unique response to a problem, and then commitment to and action from the best of the alternatives.

Jan 1, 1993

A large body of porphyry-type copper mineralization occurs at Panguna in southern BougainviIle. It is associated with the intrusion of quartz diorite/granodiorite into andesites, particularly with the contact zone. Metasomatism of both intrusives and andesite resulted in the formation of biotite pseudomorphing hornblende and the veining of the resultant biotite diorite and biotitized andesite by quartz-chalcopyrite veins with pink orthoclase and dark biotite selvages, respectively.The orientation of intrusives and veins appears to be controlled by premineralization fault-joint patterns in the intruded andesitic Kieta Volcanics.

Jan 1, 1968

By R J. Merchant

The Hauraki goldfield is located east of Auckland in the North Island of New Zealand. It includes Great Barrier Island, the Coromandel Peninsula and the Coromandel and Kaimai Ranges as far south as the town of Te Aroha and south east to Te Puke. It has a total north-south extent of about 180 km and an area of 3000 km2. The goldfield is the most productive in New Zealand, and while production at present is negligible, the area has undergone continuous exploration over the last seven years.

Jan 1, 1984

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

A Novel Diagnosis and Evaluation Procedure for Flotation Plants

Sep 13, 2010

The Nena high sulphidation-type copper-gold deposit is composed of andesitic pyroclastic units with minor interstratified lava flows. Epiclastic sandstone and conglomerate, and siliciclastic rocks consisting of mudstone, shale, lithic and bioclastic sandstone and conglomerate are locally present. Pre-mineral diorite intruded and domed the volcano-siliciclastic sequence. Economic copper-gold is hosted by vuggy quartz altered lapilli tuff and tuff breccia. The early hydrothermal alteration stage involved deposition of epithermal banded quartz and chalcedonic silica in localised environments. This alteration stage was locally superimposed by a hydrothermal breccia event. Following the breccia event, magmatically-derived volatiles were channelled through a NW striking dilational fault zone and generated the high sulphidation alteration. The high sulphidation alteration is zoned from a vuggy quartz core with local massive replacement silica through a broad pyritic quartz-alunite halo and finally to a thin illite-smectite zone. This is surrounded by regional chlorite-epidote-smectite alteration. A gangue mineral phase consisting of quartz, alunite and baryte overprinted the zoned high sulphidation alteration and preceded the main copper-gold-arsenic mineralisation. Early sulphide deposition is characterised by marcasite, arsenical pyrite and melnicovenite. Main-stage copper-gold mineralisation involved sequential deposition of hypogene bladed covellite+chalcocite, enargite-luzonite and luzonite+stibioluzonite respectively. The copper sulphides are zoned from bladed covellite-chalcocite in the north (cross-sections 5000 - 5600 N) through enargite-luzonite (cross-sections 4700 - 5000 N) and to luzonite????stibioluzonite in the south (cross-sections 4400 - 4700 N). A late phase of minor acicular covellite and enargite+luzonite overprinted the zoned copper sulphides and associated gold mineralisation. Gold mineralisation commenced at the transition from enargite to luzonite, and continued through the deposition of luzonite-stibioluzonite in both stages. Most gold was deposited during the main-stage mineralisation. Yellow native sulphur was deposited in the remaining vugs and defines the waning stage of the hydrothermal system. Post-mineral dioritic intrusives and feldspar porphyries intruded the volcano-siliciclastic sequence. Finally, supergene chemical processes with associated erosion and uplift generated a 40 - 50 m thick oxide-hosted gold cap. The oxide gold cap is underlain by a 35 - 45 m thick blanket of supergene chalcocite+covellite mineralisation which overlies and occurs throughout the main hypogene copper-gold zone. Supergene gold is related to the distribution of primary gold-bearing sulphides. Therefore, remobilisation and redeposition of gold are considered to be insignificant and very localised.

Jan 1, 1999

A study of drilling data at various stages of development of an orebody show that the semi-variogram, used for calculating the accuracy of block estimates can be ill-defined if too few data are available. The consequencesin this case are to have blocks supposedly more accurately known than is possible at the early drilling stage; such a result being potentially dangerous. However, as the amount of data increases the recalculated, semi-variograms approach the underlying semi-variogram of the deposit and the calculations made using them become more reliable and robust.

Jan 1, 1977

During Gepp's lifetime, Australia was in the forefront of science and art in metallurgical practice. This did not come easily for although blessed with a unique mineral deposit at Broken Hill large in size and rich in values much courage and daring was needed in the development of processes whereby they could yield the best results.The resultant development of the flotation processes at Broken Hill is one of the most important inventions of the 20th century.

Jan 1, 1993

The Bulli and Wongawilli Seams, the two principal sources of coking coal for the Port Kembla steelworks of Australian Iron & Steel Pty. Ltd., vary in rank and in type over the Southern and South Western Coalfields.The Bulli Seam, ranging widely in type, produces coke varying from weak to strong. The Wongawilli Seam, more consistent in type, produces coke of more consistent strength, but considerably less strong than that from the best Bulli Seam coal.Plans of seam variation show the regional trends in rank and type for each seam.The strongest coke is derived from coal containing between 45 and 55 per cent vitrinite, m.m.f. This is obtainable from the Bulli Seam in a zone embracing Bulli and Appin collieries.A satisfactory correlation is achieved between vitrinite content and coke stability and hardness, enabling prediction of coke strength for Southern Coalfield coals.The use of vitrinite reflectance, as an indicator of rank, in addition to type to predict coke strengths is at present hampered by lack of data, particularly in the South Western Coalfield. Nevertheless, data available at present allow the use of both variables and give better correlations with coke strengths than type alone.A spread of comprehensive data across both coalfields will enable advance assessment of cokes produced from coals having known rank and type. Blending to a ranktype specification for optimum coke strengths would allow the best use of the coal reserves of the coalfields.

Jan 1, 1969

I The South Platform of the Gippsland Basin is an extensive area of shallow basement covered by a relatively-thin Late Mesozoic-Cainozoic section. Although the sporadic exploration to-date has not resulted in any hydrocarbon discoveries, the area is under-explored and its taste potential has not yet been fully evaluated. The best potential appears to be in areas underlain by the Golden Beach Megasequence where structures are mainly related to basement fault blocks.

Jan 1, 1992

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

Polish coal mines are well equipped with methane monitoring systems,nevertheless the worsening conditions force a continuous impro- vement in the field of environmental monitoring. Application of modern electronic components make it possible to design the new modular telemonitoring system incorporating the best features of the older systems,widely employed in Polish collieries, eliminating their weak points. Several new sensors and portable instru- ments for methane monitoring and early fire detection have been developed and tested in mining conditions.

Jan 1, 1988

By P Taskinen, D Lindberg

The increase in metals demand in the electrifying globe means significant growth in the smelting of copper, nickel, zinc, and lead, produced from primary sulfide sources or using sulfide mattes as the intermediates of the process chains. This means that leaner and complex mineral deposits will be evaluated as ores and are in the future traded in the commodity market for smelting and refining to pure metals. An important issue in the trend is the technology metals, like antimony, tellurium, and gallium, which exist as trace elements in sulfide ores and form no ores of their own. Their recovery becomes important in the coming decades as will be the case with growing slag amounts without use in other industries. The key is to produce environmentally acceptable slags in the smelting operations. It sets new boundary conditions to the treatment of flue dusts. This means that all material streams of smelting and refining must be re-evaluated for the deportments of the main and minority metals. In copper smelting, the recoveries of precious metals are today important for the feasibility of the custom smelters but due to low prices of many minority metals they are discarded in slag landfills. It is one of the emerging issues also in the secondary copper smelting today and once the demand grows, the same question will be faced also in the mining-beneficiation-smelting-refining chain of the primary production of nickel, zinc, and lead. The distributions of many technology metals in the copper and nickel smelting have been recently studied using methods where the chemically bound trace elements in the slag and its phases at the smelting conditions have been studied. Thus, the key data about options for process modifications and additional processing steps are piling up. Short processing routes in the metals smelting and refining are attractive due to their simplicity. At the same time, complexity of many raw materials challenges the fluxing at high oxygen partial pressures in low silica slags with high metal concentrations. The compromise between high primary recovery and safe operation is a demanding task in conditions where slag foaming outside the processing window is evident. The increase in the demand of pure nickel is challenging the raw material basis where low-grade sulfide ores are soon smelted along with nickel laterites to matte. It is a demanding task at high MgO concentrations. The low solubility of MgO in iron silicate slags requires new fluxing strategies and new smelting end points for the operation at reasonable temperatures; the direct nickel matte smelting in one-matte mode may be an option.

Aug 21, 2024

By D La Rosa, K Caron, H Mamani, W Valery, R Diaz

The Gold Fields Cerro Corona copper-gold deposit in Peru has heterogeneous rock characteristics in terms of its mineralogical, geological and geotechnical properties. Blast design variations in these conditions directly impact the run-of-mine (ROM) fragmentation, which in turn influences downstream process efficiencies. In particular, when harder ore is processed, throughput and circuit performance may be limited.To evaluate the potential to increase throughput and improve overall plant performance by optimising blasting practices and comminution circuit operation, Gold Fields La Cima engaged Metso Process Technology and Innovation (PTI) to conduct a full process integration and optimisation project at Cerro Corona. Blasting, crushing and grinding processes were reviewed to identify the potential to achieve substantial improvements in productivity when treating the most competent ore types.Site-specific models of the blasting, crushing and milling processes were developed using SmartTagTM ore tracking technology for calibration and validation. Ore tracking permitted locations in the blast volume to be queried against the geotechnical block model to determine the hardness and structural parameters of the feed to the comminution circuit. They also ensured surveys were conducted when ore from the audit blast was flowing through the crushing and grinding circuits.The predictive models developed enabled PTI to demonstrate how changes in blast design influenced both ROM fragmentation and the performance of downstream comminution processes. Outcomes of the project suggested changes to blast designs and comminution practices, and these were partially implemented for a validation trial. The trial demonstrated a 14.8 per cent increase in mill throughput for the specific ore selected for the study, and an average increase of 5.7 per cent for all ore types. There is potential to further increase throughput and process performance if all recommendations are implemented. This paper describes the methodology used and benefits to the operation from the mine to plant.CITATION:La Rosa, D, Caron, K, Valery, W, Diaz, R and Mamani, H, 2015. Blast fragmentation impacts on downstream processing at Goldfields Cerro Corona, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 333–342 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R L. Brathwaite

The rocks of New Zealand can be grouped into three main elements: the Early to Mid Paleozoic Western Province, Late Paleozoic to Early Cretaceous Eastern Province, and several overlying Late Cretaceous to Cenozoic sedimentary basins. The Western and Eastern provinces were formed on or near the margin of Gondwanaland, whereas the Late Cretaceous to Cenozoic sedimentary basins developed after the separation of New Zealand from Gondwanaland in the Late Cretaceous.   The Early to Mid Paleozoic Western Province rocks are exposed in Nelson, Westland and Fiordland and include metamorphosed sandstone, mudstone, limestone, and volcanic rocks, intruded by granite batholiths and maficultramafic igneous complexes. The main associated mineral deposits are gold-quartz lodes hosted by Paleozoic greywacke and argillite. Other type of deposits present include: volcanogenic massive sulphide lead-zinc; vein and greisen tungsten and tin; and magmatic nickel-copper sulphide, platinum group element, and magnetiteilmenite deposits. Granite stocks and batholiths, intruded during the Cretaceous, have associated porphyry molybdenum deposits.   The Late Paleozoic to Early Cretaceous Eastern Province includes the greywacke rocks forming the axial ranges of the North and South islands, and a belt of schists in Marlborough, the Southern Alps and Otago. The schists host many shear-zone related, gold-quartz lodes and, in the Southern Alps, lenses of serpentinite with talcmagnesite and nephrite jade. Volcanogenic massive sulphide copper deposits and volcanogenic manganesechert deposits, occur in both the schist and greywacke, and a belt of Permian age ultramafic rocks (Dun Mountain Ophiolite) has associated copper, chromite and chrysotile asbestos deposits.   The Late Cretaceous to Cenozoic rocks are found in a number of sedimentary basins onshore and offshore of the North and South Islands. Many of these basins developed during the rifting of New Zealand from Gondwanaland in the Late Cretaceous. They contain New Zealand's economic petroleum, coal and limestone deposits. Uplift and erosion of the mountain ranges shed gold into rich placer deposits in the South Island.   From the Miocene, volcanic rocks feature prominently on the eastern South Island (e.g. Banks Peninsula southeast of Christchurch and the Otago Peninsula northeast of Dunedin) and northern North Island (Northland and Hauraki), and volcanism continues today in the Taupo Volcanic Zone. The North Island volcanic rocks have associated epithermal mineralisation, mainly gold and silver, but also copper, lead, zinc, mercury, and antimony, as well as deposits of sulphur, perlite, pumice and zeolite. Porphyry copper style mineralisation is associated with subvolcanic intrusive rocks. Erosion of the volcanic rocks has shed titanomagnetite onto the west coast of the North Island forming significant coastal placer deposits. Similarly, erosion of the Alpine schists in the South Island has resulted in placer ilmenite deposits on the coast of Westland.

Jan 1, 1997

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011