Search Documents

By Q Zhou, H Nordberg, W Wang-Geissler

Efficiently controlling foam/froth within mineral processing continues to pose a challenge to the mining sector. The foaming characteristics of aqueous solutions for two-phase systems of air/liquid are well-studied with theories and mechanisms proposed to describe and predict foam formation and stability. The types and structures of reagents that either promote or prevent foaming/froth formation and stability are well-defined in these studies and practiced across various applications. Three-phase systems of air/liquid/solid, such as froth from mineral slurries, however, pose a challenge with the presence of a large quantity of relatively fine mineral particles. Theories and mechanisms that rationalise the effects of chemical additives as a defoamer or foaming agent in aqueous can be applied as a general rule, but do not provide the most effective solution for mineral slurry systems. Silicone-based defoamers, particularly their O/W emulsions, have been widely and successfully used at various stages of mineral processing to efficiently control the mineral slurry foaming properties. However, their foaming control ability could be significantly impacted by different processing aids used during the upstream process. In a zinc-rich mineral system, a silicone-based defoamer starts losing the properties necessary to effectively control foaming in the leaching circuit when throughput is increased. In this study, the synergistic defoaming/anti-foaming effects from surfactants and silicone-based defoamers are discussed to effectively control foaming/froth in the zinc leaching circuit, even with lower total defoamer dosage. Improvements during mineral processing can also lead to a cleaner mineral grade by reducing waste.

Aug 24, 2022

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

Good morning and thank you for the opportunity to address this yearÆs New Zealand Minerals Conference.   As you have already heard from the Associate Minister of Energy, the Government believes that the minerals industry is an important part of our economy. In particular, our coal and lignite resources have the potential to play an important role in New ZealandÆs energy sector as both a primary fuel and as a means to produce electricity.   The Government has taken a keen interest in the primary fuel sector given the declining reserves of natural gas sector. The energy sector is a key driver of economic growth and it is therefore critical that we have a reliable supply of primary fuel as part of the energy mix.   In a global sense, New Zealand is like many other countries regarding the need to secure energy for the future. Natural gas will be a key bridging fuel in the transition from an energy market based on fossil fuels to one based on renewables over the next century.   However, natural gas as a solution to this energy transition has some pragmatic limitations for New Zealand. There is uncertainty as to when new domestic reserves of gas can be discovered and developed. And the alternative of imported LNG poses a number of costs and risks to the economy.   New ZealandÆs coal resources are vast-estimated to be enough to last hundreds of years at the current rate of extraction. The main question is can extraction be increased and sustained to meet the demand of domestic power producers and at the same time meet commitments to lucrative international markets?   At this point it is appropriate for me to place coal into context with Governments overarching policy objectives for energy. The Government has stated objectives for the energy sector emphasising energy efficiency and an increased focus of renewable energy, while still ensuring security of supply and certainty as to energy costs and risk. Coal certainly can make a contribution to these objectives going forward.

Jan 1, 2005

Thank you for the opportunity to speak at this important conference attended by aspiring mining professionals, some of whom will become the leaders of the mineral resources industry that forms the solid foundation of AustraliaÆs past and that will fuel the exciting growth of AustraliaÆs future.I want to briefly touch on the history of our business, then look at the opportunities that exist in the contract mining industry and finally comment on what the educators need to consider in their curriculum to meet the needs of our business. Byrnecut started out as an idea in early-1987 developed by a group of four mining people. At the time the industry was on the high end of a mining boom, the era of the Bonds, Connels, Skases and so on. Riding on this wave of euphoria we borrowed $600 000 from the National Australia Bank and, without having enough knowledge to lose sleep over the potential risks, started business in mid-1987. The euphoria quickly evaporated with the 1987 October stock market crash. The bank pulled our overdraft, equipment finance rates increased to over 20 per cent per annum and my house was mortgagedseveral times over. The business learning curve was extreme for a young mining engineer who had developed his trade in the relatively sheltered environment of a large public mining house, namely WMC. We were somewhat bitter that the banks had done a runner. We were a private company, backing the business with personal assets with our shoulders to the wheel, whilst the Bonds of the world had theirnoses in the trough ripping off mum and dad shareholders. All of this had a sobering effect, namely keep your feet on the ground, stick to the knitting, work hard and worship cash flow. Since that stressful but adrenaline pumping beginning the company now employs over 600 people and is now working for major mining houses at over a dozen locations in Australia, east Africa and WesternEurope and the National bank is again our banker. On this basis I consider myself qualified for the subject of this speech.

Jan 1, 2002

It is always difficult to sum up an open forum adequately and instantaneously, so, with the privilege of hindsight, and also with some time to reflect, I am exercising the Chairman's prerogative to put together my view of the overall conclusions. Hopefully, these may provide a focus for each Institute to formulate its own programme with respect to mineral industry education. First, in answer to the question, "Should there be Schools of Mines?", there was a very clear 'yes'. However, I reiterate what I said in the introduction to this forum, specific professional education for the mineral industry exists only because the mineral industry sees a need and wants it. If the mineral industry should decide that it does not need professionals with specific mineral industry training, then such training will cease to exist. As alluded by Dr Hackett, if such training ceases to exist, one must then question the need for Institutes of Mining and Metallurgy. Now, there's some food for thought! Specialist schools of mines (metallurgy and geology) can only exist in an environment of genuine interaction with, and support by, industry. For their part, schools of mines, used here in a generic sense, require leadership that is strong but responsive to industry needs. It is the leader that puts his stamp on a school, and, to a large extent, determines whether that school is 'good' or only 'mediocre'.

Jan 1, 1986

Mining of narrow vein mineralisation, invariably depending on the mining method selected, involves the extraction of both ore and waste rock. The level to which mining of waste rock can be minimised depends on numerous factors, but particularly the thickness and dip of the deposit. Resue mining is a method of mining that allows split face firing within stopes to allow waste and ore to be mined separately, allowing dilution to be minimised. This paper examines the technique of resue firing and its applicability to the mining of narrow vein deposits. Particular emphasis is placed on the conditions in which resue mining presents a suitable option for mining of narrow veins.

Jan 1, 2008

By A Kleinitz, J Halilovic, K Trappitt

Mine operators use grade control to determine the destination of each block of material in the mine. In polymetallic mines, grades are best expressed in dollars: the Net Smelter Return, NSR, per tonne. To estimate NSRs, geologists working on grade control develop models for each geometallurgical domain in the mine. These models may incorporate observations on the mineralogy and grain sizes of the material being examined. The site’s mill operators contribute to the models by providing geologists with statistical analyses that relate assay results and mineralogical compositions to metallurgical parameters, such as the rates of recovery of each economic metal to each of the concentrates produced, and the compositions of those concentrates. The team responsible for sales and marketing of the site’s products contributes to the NSR models by providing details of the costs of shipping concentrates to smelters and refineries; and by providing figures that are specified in the smelter contracts, such as the payability of the metals in each concentrate and the fees charged by the smelter. The mill operators also provide, for the NSR models, equations to estimate the rates of recovery of deleterious materials to each concentrate. Deleterious materials comprise mostly halogens and amphoteric elements, both of which reduce the efficiency of smelters. Furthermore, deleterious materials such as antimony and arsenic may be poisonous to people and to the environment. The sales and marketing team provide specifics of the penalties that smelters impose upon deleterious materials. These penalties may reduce NSRs by tens of percent, possibly to levels below the cut-off grade. Thus, in the blocks that are subject to grade control, mine geologists monitor not only the concentrations of economic metals, but also the presence and abundance of deleterious materials. The preparation and maintenance of models, to estimate NSRs and to assess changes in the levels of potentially toxic materials to be mined, requires close and continuing consultation between corporate departments. There must be strong communication of mine geologists with the mill operators; with the people who market the mine’s concentrates; and, should there be a risk of encountering toxic levels of deleterious materials, with the mine’s health, safety and environmental officers. This co-operation could require radical changes in the structure of many organisations. However, experience suggests that such changes can significantly improve the profitability of a mine.

Mar 22, 2022

By R Mackay, J Brereton

On 30 June 2020, the Mine Land Rehabilitation Authority (the Authority) superseded the Latrobe Valley Mine Rehabilitation Commissioner as the independent overseer of Victoria’s declared mine rehabilitation. Currently, only the Latrobe Valley’s three brown coalmines are declared, with each mine at a different stage of rehabilitation and closure planning: Hazelwood ceased mining in 2017, Yallourn is scheduled to end mining in 2028 and Loy Yang in 2035. The three declared mines are very large, close together (Figure 1) and present significant environmental risks that must be mitigated during rehabilitation and post closure. In addition to fire risks, the brown coalmines are inherently unstable and require continuous monitoring and management of ground movements and groundwater pressures. Since 2007 several damaging events have occurred, highlighting the difficulties of achieving long-term stability, even with good landform design and rigorous ground control management plans

Aug 2, 2023

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By M Robotham

In April 2013, Rio Tinto Kennecott Copper’s (RTKC) Bingham Canyon mine experienced what is arguably the world’s largest ever in-pit slope failure. The failure initiated along a major, continuous, low-strength bedding fault, named the Manefay bed, and comprised approximately 145Mtonnes of rock and waste dump material. Initial East wall slope deformations were detected some months prior to catastrophic slope collapse by RTKC’s slope monitoring systems. However, the failure mechanism was different to that which had historically been experienced in the prior more-than-100 years of open pit mining. Failure occurred as two separate events, the initial one likely consisting of a frictional failure of rock materials along the Manefay bed itself, before a second phase of failure occurred, which included a large mass of old rail dump material. The combination of these events led to a much larger failure run-out than had been anticipated by the RTKC team which led to loss of, and damage to, mining equipment and infrastructure as well as significant interruption to mining activities. Due to the diligent monitoring of the slopes no safety impacts were experienced at the mine, and as such the details and learnings from this failure can readily be shared with the broader mining and geotechnical industries to avoid similar recurrences elsewhere. This is an extended abstract only. CITATION:Robotham, M, 2018. Bingham Canyon Mine – from adversity to excellence, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Prill

Safety First and zero accidents are the targets most mines in Australia are aiming for, but manual processes and procedures limit the capabilities and response time in emergency situations. Even with a high safety focus, accidents and incidents still happen, too often with tragic outcomes. Dangerous areas, narrow roads and winding curves are all daily obstacles that threaten workforce safety. Every unforeseen event, such as traffic collisions and other accidents, puts lives in danger and weakens production. Safety must be guaranteed.

May 5, 2022

By A Gibbs

The mining sector has been a leader in investing in safety improvement initiatives, yet relatively few mining organisations can accurately track the positive effects of these initiatives or identify areas that may require more attention. The consequences of not taking safety seriously are severe, and unfortunately injuries and fatalities are continuing to occur across the mining sector (Brady, 2019). There is a tendency to turn to lag indicators such as All Injury Frequency Rate (AIFR), Total Recordable Injury Frequency Rate (TRIFR), and Lost Time Injury Frequency Rate (LTIFR) to track these outcomes. As outlined below these approaches are inherently flawed and a renewed focus is needed on indicators within the control of leaders, indicators that have high predictive validity for future events and data that is used in a way to enable learning and change.

May 5, 2022

By C Sylvestre

Leaders have invested heavily in traditional safety management to improve safety performance over the years. This primarily involved: • fixing the environment (eliminating the hazard) • improving the system (more/less rules, procedures etc) • making safety more conscious (more/better interactions about the importance of safety). These approaches have helped improve safety performance significantly during the last 50 years and will continue to play a role in the future. Although these approaches may be part of an overall solution, they are not enough to prevent many incidents. Today, these three approaches are used more than before, and are used better than ever before. Yet, workplace fatalities in Australia have stagnated from 2013 to 2019, as have the number of incidents, even serious ones. In the USA, workplace fatalities have increased by 15 per cent in the same period.

May 5, 2022

By H Indirawati, R Ayres, A Nur Kasnanto, S Konopa

As a project moves through the mine life cycle, the quantity of data available increases and the understanding of the orebody matures. Incorporating new information quickly and efficiently in current 3D models, is essential for adding value across the life-of-mine value chain. At the Martabe Gold Mine, the resource development group manages 14 drill rigs on six resource projects, including three operating mines. The Martabe deposits are geologically complex and the volume of new information that becomes available each day is substantial. It is imperative that new geological and assay information is integrated into the 3D models as soon as possible, so that drill planning and targeting can be modified accordingly. Martabe uses Leapfrog<sup>®</sup> 3D software to update and interrogate the 3D models on a dynamic basis as data becomes available. This results in faster and more effective changes to drill planning and schedules. The impact of this is better drill productivity and cost savings due to optimal drill targeting, and availability of up-to-date models incorporating the most current data. CITATION: Konopa, S, Ayres, R, Nur Kasnanto, A and Indirawati, H, 2018. Optimised drill targeting using dynamic 3D modelling, Martabe Gold Mine, Indonesia, in Proceedings Complex Orebodies Conference 2018, pp 99–101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Australia as a leading producer of mineral sands has also occupied a leading position in many areas of research'in the processing and applications of these minerals. Research in upgrading ilmenite to produce synthetic rutile has resulted in the develop- ment of many processes, e.g,., Becher, Murso, Chlorine Technology, and ICI processes. Studies on the reducibility of ilmenites, aqueous leaching of reduced ilmenites, Fe-Ti-O system, leachability of natural and treated ilmenites in hydrochloric acid and selective chlorination of iron from ilmenites have been carried out in order to develop and improve the efficiency of the above processes. While research on the processing of zircon sand to produce high purity (99.99% ZrO2 zirconia powder and zirconium chemicals started only recently, research by CSIRO in the early 1970s led to the discovery of the phenomenon of transformation toughening in partially stabilized zirconia (PSZ) ceramics. Australia, with very significant resources of lanthanide-containing ores, pro- duces substantial quantities of monazite each year but research in processing and appli- cations of rare earths was neglected in recent years in this country. However, research to improve processes for the recovery of rare earths is now under way and studies on the production and testing of Nd-B-Fe magnets which are 1.5-2 times stronger than the strongest magnets (Sm-Co) currently available, have also commenced.' An overview of the research in the pro- cessing and applications of mineral sands during the last two decades in Australia and its implications for the industry are pre- sented in the paper.

Jan 1, 1986

By S D. Fox, P B. Swart

Statistics showing that mine rehabilitation is falling behind rates of disturbance continue to be reported in the media. Unfortunately, most reported statistics do not account for the large growth-cycle that mining in Australia experiences, where there are typically significant new disturbances with large portions of these areas not being available for rehabilitation for a number of years. Many commentators assert that better planning is required to ensure that rehabilitation will be able to achieve a safe, stable, non-polluting landform that meets the agreed post-mining landuse.This paper focusses on the revegetation aspects of mine rehabilitation and in particular the matters that need to be addressed in the planning stage so that revegetation success is ultimately able to be demonstrated to regulators and other stakeholders.CITATION:Fox, S D and Swart, P B, 2018. Planning revegetation for relinquishment, in Proceedings Life-of-Mine 2018, pp 113–115 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By M Liang, C Putzmann, D Gokaydin

The mining industry faces numerous challenges in swiftly evaluating and exploiting new mineral deposits to meet the escalating demand for critical minerals and metals. These challenges necessitate the adoption of innovative techniques and technologies to expedite development cycles and facilitate the efficient exchange of knowledge and expertise. Traditional mineral exploration methods rely heavily on data governance, visualisation tools, and expert interpretation skills, often operating in isolation and limiting the integration of valuable data and knowledge (Lindsay and Perrouty, 2019). To address these integration challenges and bridge the industry’s knowledge gap, the concept of a digital twin offers a holistic solution (Ahn, 2021; Nagovitsyn and Stepacheva, 2021).

Sep 1, 2024

By Boyd GL

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal rCCOvCrCd h\ hi'eh ss-all mining methods.

Jan 1, 1998

By I KylmSkorpi, H Mansikkaviita

The traditional direct-heated drying process has been replaced by the steam drying process in non-ferrous metal smelters, where steam is available from waste heat boilers. Many recent projects have selected Kumera Steam Dryers in equipping a new production line or modifying an old production line. The industrial performance of the steam dryers has shown significant energy saving and emission reduction. The steam dryers have been operated at high availability and long maintenance interval. As the process principle of Kumera Steam Dryer is different from other equipment, the set-up for steam dryer plants is configured to fit the smelter site and operation conditions to achieve optimal performance. This article discusses the equipment involved in the steam drying process and their combination options.

Jan 1, 2008

By N Trabelsi, D Bakun-Mazor, Y Ben-Ari

As part of a comprehensive project to develop a remote sensing tool for evaluating the mechanical properties of rocks, one must obtain a rapid indication of these properties using conventional field methods. A common method for evaluating the mechanical properties of rocks in the field is to use a Schmidt hammer, a portable device that measures the rebound (R) of a spring-loaded mass impacting against the rock surface. Since the 1960s many studies have been made to find empirical correlations between the R value measured by the Schmidt hammer and mechanical and physical properties such as uniaxial compressive strength (UCS), elastic modulus, density, and porosity. Despite the existing correlations in the literature, this work is required to establish detailed empirical relationships for the carbonate rock units in Israel. To do so, 150 rock samples were collected from 38 different outcrops of carbonate rock units. In each outcrop, 20 impacts were made using a Schmidt hammer at different but adjacent points. The impacts were done horizontally perpendicular to the vertical rock walls. In the laboratory, we measured the density, effective porosity, water absorption, UCS, and elastic modulus. The rock samples we selected contained a wide range of UCS: from 7 to 270 MPa. Our empirical correlations indicate an exponential relationship between R and UCS and the elastic modulus, and linear relationships between R and density, porosity, and water absorbance. The most reliable index is the average of the five maximum impacts out of the 20 made in each rock outcrop. The correlation equations obtained from this work will make it possible to effectively evaluate the mechanical properties of the intact rock in the field, thereby aiding development of advanced tools for rock mass characterisation by means of remote sensing.

Nov 29, 2022