Search Documents

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By J Rutter, J du Plessis, er, M Scott, D Alex

It is generally acknowledged that bulk ore sorting is an attractive prospect for the mining industry. However, uncertainties relating to the operational performance of sensor technologies, the grade heterogeneity present in analysed material and the physical separation performance of the coupled system complicate the evaluation and deployment of bulk ore sorting strategies at operations. To assist in the quantification of these uncertainties, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and Anglo American have implemented a systematic methodology to evaluate the deployment of sensor technologies for bulk ore sorting. This methodology was implemented at a bulk ore sorting demonstration plant using penetrative prompt gamma neutron activation analysis (PGNAA) and surface x-ray fluorescence (XRF) measurements of base metals, as a proxy for precious metals, at Mogalakwena PGE Mine. The methodology comprises of three phases. The initial phase involves the preliminary investigation of sensor technologies and analysis to reduce identified risks prior to commissioning of the bulk ore sorting plant. The second phase executes a series of experiments to prove the sensing technologies in the operational environment and provide confidence the sensors can drive separation. The final phase demonstrates the production scale bulk ore sorting performance of the plant and validates its performance by campaign of the sorted products at the processing plant. Throughout the operational deployment and evaluation of bulk ore sorting at Mogalakwena, several key lessons were learned. These learnings relate to the calibration requirements of the sensor technologies, the application of surface vs penetrative sensor techniques and the preservation of grade heterogeneity delivered to the sensors. This paper presents the methodology used, and lessons learned, in the operational deployment and evaluation of PGNAA and XRF sensors for bulk ore sorting at Mogalakwena PGE Mine.

Nov 10, 2020

By P A. Grossman, J H. Rubinstein, M Brazil, K G. Sirinanda

To date, the scheduling and access design of an underground mine have only been considered as two separate optimisation problems. First, access to the mine is designed and then the scheduling is completed. One drawback of this approach is that the costs of access construction fail to be reflected in the net present value (NPV) calculation. In this paper, designing the access and scheduling its construction are formulated as a single optimisation problem.The underground mine access construction process can be classified according to the number of faces being developed concurrently. An underground mine with a single decline branching at a junction point into two declines is considered. After construction reaches the junction, the two faces of the decline can be constructed sequentially or concurrently.This paper proposes an efficient algorithm for optimally locating a junction point to maximise the NPV where two faces are being developed concurrently. The NPV is defined by taking the locations of orebodies and their values, decline construction costs, decline development rate and discount rate into account. The variation of the NPV and the optimal locations of the junction point for one and two concurrent development faces for a range of discount rates are discussed and compared. The proposed algorithm is applied in a simulated case study based on hypothetical values for an underground mine.CITATION:Sirinanda, K G, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Strategic underground mine access design to maximise the net present value, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M I. Pownceby, M A. Rhamdhani, D M. Fellicia, S Palanisamy, R Z. Mukhlis

The trend of global copper production has prospectively increased over time. Based on typical mined ore grades, 1 t of copper ore generates approximately 6–10 kg of copper, which requires much energy, usually in the form of metallurgical coke. Copper production using carbon as a fuel and reductant contributes up to 0.3 per cent to global greenhouse gas (GHG) emissions. As a result, research into decarbonisation processes applicable to reducing low-grade copper sulfide ores, copper oxides, electronic wastes and other alternative complex Cu-rich materials has increased. Alternative fuels for reducing carbon-rich emissions in pyrometallurgical copper processing include methane, ammonia, biomass, solar and wind power, but in recent times increased focus has been on hydrogen as a potential fuel and reducing agent for materials such as oxidised copper scrap, Cu2O/CuO and Cu-rich slags/e-wastes. From a thermodynamic perspective, hydrogen exhibits a significantly more negative standard Gibbs free energy (ΔG°) than copper oxide making it a suitable reductant and the exothermic thermal effect from reaction between hydrogen and Cu2O/CuO may be used to control process parameters. These characteristics renders hydrogen an ideal gas for reducing copper oxides and copper-containing slags/e-wastes. This review article assesses previous research on utilising hydrogen for producing and refining copper from primary and secondary feed materials.

Jun 19, 2024

Conditional simulation can be used to determine the probabilities of block iron-grades being above selected cut-offs. However, there are much faster alternatives that can produce acceptable results. In this paper blasthole data from a selected area of Joffre Member hosted ore of the Brockman Iron Formation at the Mt Whaleback orebody is used as the basis of a case study to assess alternatives to simulation. Iron grade, in per cent, is interpolated from a blasthole dataset into a block model using ordinary kriging. Samples are then removed from this blasthole dataset to produce data subsets. A complete distribution of iron grades for points or blocks is obtained utilising the data subsets and the following techniques: conditional simulation, median indicator kriging, the probability from conditional expectation and confidence intervals attached to the estimation of blocks in the framework of the discrete Gaussian model. The complete blasthole dataset is considered to represent the true iron grades at sample point support while the ordinary kriging estimate derived from these samples is considered to represent the true block grades. The distributions obtained from point estimates, block estimates and simulations are compared to each other and to the true estimates of iron grades using graphs and statistics. The conditional expectation technique reproduced the results obtained from conditional simulation extremely well and it is a viable alternative to simulation at point support. At block support the confidence intervals technique reproduced the results of the conditional simulation more closely than the median indicator kriging and in the data subsets tested the confidence intervals technique actually reproduced the true grade distribution more closely than the conditional simulation.

Jan 1, 2005

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

By M Lee, J F. Carswell, G Reitsema

"The increased costs of underground mining have continually challenged engineers to identify opportunities for alternatives to common approaches to underground development. Considerations to the design of horizontal and vertical development at the Dugald River mine targeted inclined raise boring to reduce horizontal development, not only to reduce cost, but to allow development activities to focus on other areas of the mine.The mine plan consists of 50 raise bored ventilation shafts, of which 17 have been mined to date with diameters ranging from 3.1 m to 5 m and lengths from 30 m to 200 m. The expected performance and stability of these shafts has been determined using methodologies proposed by McCracken and Stacey (1989) and further refined by Peck, Coombes and Lee (2011). Actual raise performances have been collated and compared to a database of raise bore performances across Australia as presented by Coombes, Lee and Peck (2011), and form a database of raise bore performance specific to Dugald River.Opportunities to further optimise the mine plan and reduce costs have seen the introduction of large diameter-inclined raise bored ventilation shafts to minimise the required lateral development to connect the ventilation circuits. Large diameter inclined shafts ranging between 3.1 m and 4.5 m in diameter have been successfully mined with dips down to 70°, reducing the cost of lateral development by more than $1 million over the next two years.Both technical and operational challenges were overcome in the mining of large diameter-inclined raise bores, including modification of: existing methodologies of assessing shaft wall stability for inclined raises. These included variations of the McCracken and Stacey method and the utilisation of the modified stability number (N’) previously developed for stope performance (Potvin, 1988). both the collar and toe development profiles, including the general set-up of the raise bore drill rig to reduce the operational risks associated with angled raises.Due to their success, inclined raises have been designed for subsequent stages of the life-of-mine ventilation system at Dugald River. This has resulted in significant capital cost savings for the mine.CITATION:Carswell, J F, Reitsema, G and Lee, M, 2017. Vertical and inclined raise bore performance at Dugald River mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By J Zhou

This paper discusses the implementation of a mixed integer linear programming model for a coal preparation plant. The plant considered consists of primary and secondary heavy media cyclones, hydrocyclones for intermediate fines and froth flotation for the very fine material. The model is designed to optimise the plant settings and product flows to maximise revenues for a given specification for two product outputs. The model can deal with bonus/penalty aspects of the product pricing for products that exceed or fail to meet specification. We report on a model with two separate coal feeds with parallel circuits for the oversize, intermediate and fines streams. The genesis of this model is more than 30 years old but recent improvements in mixed integer programming solvers make a full mixed integer formulation practical. The original model began as an enumeration of cut points with arbitrary rules for product allocation. The product allocation was improved in a linear programming formulation by Gunn (1982) and Sarker (1991 and 1995). Current mixed integer programming capabilities make it possible to replace the enumeration aspects and solve directly as a mixed integer programming problem. The current implementation uses a general purpose modelling language to formulate the model. Open source and commercial mixed integer programming solvers are compared

Sep 26, 2011

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

Mining operations in the Obuasi mine of AngloGold Ashanti Limited began in 1897 using mainly gravity concentration and amalgamation to recover the gold from predominantly high-grade quartz ores. The mine is primarily an underground operation, although some surface mining still takes place. Ore is currently processed by two main treatment plants: the Sulfide Treatment Plant (STP) for underground ore and the tailings treatment plant for tailings reclamation operations. STP was commissioned in February 1994 to treat 180 000 t/m of double refractory gold ore and it hosted the then world's largest commercial scale bacterial oxidation plant which uses Gencor's BIOX« technology. Gold is recovered by gravity and flotation, with the regrinding of the sulfide concentrate before bio-oxidation to liberate locked gold in sulfi de minerals. The BIOX« product is leached using the carbon in leach (CIL) process. Gravity gold recovery is a major component of STP operations and its contribution to overall plant recovery is about ten to 13 per cent. Gravity recovery has undergone series of technological upgrading, since the very first circuit which consisted of a Knelson concentrator and a Gemeni shaking table which was incorporated into the milling circuit at the start of the plant. Presently, each of the gravity circuits which consists of Knelson concentrator(s), cyclones and Gekko InLine Reactors (ILR), are located at the Milling and BIOX« circuits. More recently a new gravity recovery facility comprising of four 48 inch Knelson concentrators and cluster of ten inch cyclones have been incorporated at the tail of the flotation circuit. An additional ILR will be commissioned in 2010 to treat the concentrate generated from the new Semi Autogenous Mill #2 (SAG 2) Knelson: concentrator tower under construction. Since the inception of STP, significant gravity recoverable gold has been recovered via Knelson concentrators and the employed circuits have seen a number of modifications and upgrades, motivated by ore mineralogical changes and recovery concerns. The pioneering adoption of the ILR technology in 2001 and 2003 was a critical factor in enhancing the improved recovery benefit of the gravity circuits. Therefore the objective of this paper is to highlight the mine's experience in the gravity recoverable gold process with emphasis on plant modifications and gravity equipment upgrade. Operational challenges and the contribution of gravity gold to overall plant recovery are also discussed.

Aug 1, 2010

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By N Schofield

For the sampling of particulate materials in mineral exploration and mining, the fundamental sampling error (FSE) introduced by Gy is a measure of the constitutional heterogeneity of the sample lot and is expressed as the relative standard deviation of subsample grades of a particular mass. The FSE is presently regarded as an important indicator of quality for samples used in resource estimation. Constitutional heterogeneity describes an ideal state of heterogeneity with respect to all constituents of the lot such that the fundamental error among subsamples of a particular mass is minimised.In this paper, the term ‘sampling precision’ used in relation to mineral resource sampling usually refers to a statistic based on the assay results drawn from pairs of separate subsample splits of multiple sample lots. The pairs of splits are extracted after the lots have been prepared by crushing and pulverising to meet specified criteria of grain size and subsample mass. There is presently no generally accepted method of calculating the ‘sampling precision’ from such paired data but some form of the relative standard deviation that is consistent with definition of the FSE is preferred here. The work of Thompson and Howarth in the 1970s on geochemical analytical precision, which has been subjected to extensive examination and criticism by Stanley and Lawie (2007), and that of Francois-Bongarçon since the 1990s forms the background to the discussion in the paper.A significant aspect of the application of Gy’s sampling theory to sampling in gold deposits is the requirement that the fundamental error be maintained at less than ±20 per cent. The most important reason for this is to ensure that the effects of other sampling errors such as the grouping and segregation, and increment delimitation which can cause local and global biases in sampling are kept as small as possible. This paper is focused mainly on the quality of sampling in gold deposits and looks at an alternative to the use of a constant sampling precision applied to a collection of lots with varying average grade. A theoretical model for the FSE based on duplicate sampling is presented and the simulated results of the model are compared to practical outcomes of real duplicate pairs drawn from multiple sample lots. The goal of the work is to present a more informative analysis of duplicate sample data from multiple lots which may allow a more informed view of the potential for bias generating errors during sample preparation and processing.

Aug 22, 2011

By P Holtham, J Meng, E Tabosa, W Xie

Turbulence and its distribution are of great importance in flotation, and have received considerable attention recently. However, there is no mature technique to measure turbulence in three-phase (liquid-solid-gas) industrial flotation cells due to the opaque, highly aggressive and abrasive nature of the slurry involved. Previous research has shown that the piezoelectric vibration sensor (PVS) is a promising tool for turbulence measurement in industrial flotation cells. The PVS is a robust device that converts mechanical vibration to electrical signal, from which turbulence information can be extracted. An improved calibration method has allowed development of a frequency model to calculate the force applied to the sensor. Experimental results and comparison with laser doppler anemometry (LDA) have shown that the PVS can measure fluid kinetic energy, which is related to turbulent kinetic energy, a parameter used in the literature to represent turbulence in flotation. Laboratory measurement in a two-phase (water and air) 60 L cell and with slurry in a 3.5 L cell gave good stable results and mostly consistent trends between the measured turbulence profile and cell operation. When applied in a 300 m3 industrial cell filled with water, the addition of air or slurry to the cell resulted in a shift in the turbulence profile. This is expected because a change in fluid density will change the force applied to the sensor. It is therefore concluded that the piezoelectric sensor is an easy-to-use and robust technique that is fully capable of measuring turbulence in industrial flotation environments.CITATION:Meng, J, Tabosa, E, Xie, W, Runge, K C and Holtham, P, 2014. Development and application of a piezoelectric sensor for turbulence measurement in industrial flotation cells, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 457–470 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By L Kormos, V Lawson, G Hill, G Marrs

"In sulfide nickel deposits throughout the world, pentlandite and pyrrhotite are commonly found together along with varying amounts of chalcopyrite and platinum group minerals (PGMs). The mafic or ultramafic host silicates associated with the sulfide mineralisation commonly exhibit a complex assemblage of magnesium bearing silicates, many of which themselves contain significant nickel. Four types of ore are proposed, each presenting their own processing challenges. These are: economic grades of Ni, Cu and PGE (platinum group element) in a pyrrhotite-bearing sulfide deposit, with low pyrrhotite to pentlandite ratios  economic grades of Ni, Cu and PGE in a pyrrhotite-bearing sulfide deposit, with moderate to high pyrrhotite to pentlandite ratios uneconomic high pyrrhotite: low tenor deposits low-grade low sulfide, high MgO ± PGE deposits that can sometimes be economically mined and processed.The grades and recoveries of nickel concentrates produced from sulfide ores can be significantly impacted by the ore mineral texture, the nickel tenor of the sulfides, and the polytype of pyrrhotite which may be either hexagonal (non-magnetic) or monoclinic (magnetic). The mineralogy of the silicates is also of great importance, especially the magnesium silicates and those which tend to produce particles which are asbestiform or which affect slurry viscosity. Other magnesium silicates such as serpentine carry nickel in solid solution, limiting the recovery entitlement of nickel by flotation because serpentine is not amenable to sulfide flotation mechanisms. Differences in plant flow sheets and reagent assemblages are required to effectively separate these minerals.Experience from a variety of plant operations and from extensive flow sheet development programs are discussed. Examples are given of where significant improvements in nickel circuit performance can be made by adjusting plant physical processing conditions or process chemistry to compensate for measurable ore properties and characteristics.CITATION:Lawson, V, Hill, G, Kormos, L and Marrs, G, 2014. The separation of pentlandite from chalcopyrite, pyrrhotite and gangue in nickel projects throughout the world, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 153–162 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By A N. Parry

In May 2018 Kasbah Resources Limited (“Kasbah”) completed an ore sorting test work program which was a precursor to releasing in July 2018 an updated Definitive Feasibility Study (“DFS”) for the Achmmach Tin Project in Morocco, which it is proposing to develop along with its joint venture partners. The testwork program evaluated ore sorting as a pre-concentration option to achieve early elimination of gangue and the low-grade component of ROM feed, thereby potentially:  Significantly upgrading the head grade of tin to the downstream processing plant.  Significantly reducing the required throughput capacity (and projected capital expenditure) of the downstream processing plant.  Reducing total consumables, power and water requirements in downstream processing.  Increasing the recovery of tin in the gravity and flotation circuit due to the higher feed grade achievable with ore sorting.  Reducing tailings tonnage, tailings cost and environmental footprint.  Using sorter rejects for mine backfill or road base applications. Key aspects of the design of the metallurgical testwork program centred around the need to ensure that samples representative of ROM ore feed (including projected mining dilution) were selected for the ore sorting testwork. The design and implementation of the ore sorting bulk testwork program is described, as well as a summary of the test work results and a discussion of the enhancement of the project economics reported by Kasbah, which led the company to adopt ore sorting as part of the proposed processing circuit in the updated 2018 DFS.

Nov 10, 2020

By M Spagnolo, M Ashley, D, L Reemeyer

PasmincoÆs Century Concentrator in North West Queensland commenced operations in November 1999. The nameplate production capacity of 500 000 tpa of zinc metal production in concentrate was achieved in August 2002. Completion of the production ramp up was successful due to the culmination of a number of initiatives throughout 2001 and 2002. Mine to mill interaction to understand and eliminate head grade related bottlenecks affecting Concentrator production and reduce feed variation. Grinding circuit process development û operating and process control strategies to improve stability and reduce grind size to support zinc recovery. Pumping upgrades to control spillage in ultrafine zinc flotation Low density zinc flotation strategy û to improve silica-sphalerite separation to improve zinc recovery while maintaining acceptable silica in final concentrate. Flotation circuit process development û froth crowders, froth cameras and reagent control strategies to improve primary zinc flotation performance. Review and implementation of longer campaigns between planned shutdowns to improve availability. Team reorganisation û to improve setting and implementation of metallurgical strategies. This paper describes these initiatives and their contribution in achieving the production target. It also notes the ball mill motor failures that delayed the successful achievement of the ramp up, and CenturyÆs response to minimise the production impact. The paper also outlines the capital improvement program that was implemented to improve zinc recovery to design 82.5 per cent recovery once the production rate had been achieved.

Jan 1, 2003