Search Documents

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

By F Butler, G E. Batley, A C. Hogan, A R. Butler

The ANZECC/ARMCANZ (2000) Water Quality Guidelines (the Guidelines) are the primary reference used in Australia and New Zealand for managing and regulating water quality. For most mining operations in Queensland, the environmental authority (EA – licence) incorporates the national default guideline values (GVs) for ecosystem protection as trigger levels (TLs). Exceedances of TLs ‘trigger’ further investigation and reporting. A review of the surface water compliance history at a metalliferous mine in North West Queensland identified minor exceedances of the cobalt GV as a common trigger for investigation and compliance reporting.The reliability of GVs is dependent on the availability and quality of ecotoxicology data for the relevant contaminant. The current national default GV for cobalt of 1.4 µg/L is classified as a low reliability GV due to the lack of available data at the time it was derived (ANZECC/ARMCANZ, 2000).The Guidelines are presently being revised and the toxicant GVs will be available as a set of web-based values and associated technical briefs. The new platform will enable the timely revision of existing GVs and inclusion of GVs for additional toxicants. Cobalt was considered a priority toxicant for the Guidelines’ revision, but was not included in the revision process.A preliminary review of the international literature indicated that at least 15 additional chronic cobalt toxicity studies had been published since 2000, sufficient to derive a high reliability cobalt GV using the protocols developed for the revision of the Guidelines (Batley et al, 2014; Warne et al, 2015). This presented an opportunity to improve environmental management by increasing the reliability of the performance measure.CITATION:Hogan, A C, Butler, A R, Butler, F and Batley, G E, 2016. Derivation of high reliability water quality guideline values for cobalt in freshwaters – improving water quality guidelines for better water quality compliance management in mining, in Proceedings Life-of-Mine 2016 Conference , pp 205–208 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Holmes RJ, Sowerby BD, Watt JS

Major improvements have taken place in mineral and coal processing in the last decade. The development of nuclear on-line sensors that continuously analyse the material being processed has led to better control of metalliferous mineral processing and increased recovery of valuable minerals. The recent development of on-line techniques for analysis of coal is expected to be of similar Importance. Australian developments in on-line nuclear gauges are reviewed. These include systems for in-stream analysis of mineral slurries with comments on plant operating experience; on-line determination of ash in coal using low energy Y-ray transmission and pair production techniques; in-stream determination of solids weight fraction and ash content of coal in slurries with variable voidage; and on-line determination of moisture in coal, iron in high grade iron ores and sulphur in lead sinter.

Jan 1, 1986

By Q Gong, J Li, J Zhao, Y Zheng

Excavation by tunnel boring machines (TBMs) offers many advantages over conventional excavation methods, in terms of safety level, working environment, advance rate and overall cost. While TBMs have been extensively used in civil tunnel construction, they are also viewed as a competitive alternative to the drill-and-blast method for underground mining, attracting increasing attention from the mining industry. This paper presents an overview and general assessment on applications of TBMs in mines, by reviewing more than 60 TBM applications in underground/open pit coal and hard rock mines around the world. The projects range from the early exploratory trials of TBMs in mines in Germany, England, South Africa and America in the 1960s and 1970s, to the ongoing projects in Australia, China and Chile. The paper focuses on the geological compatibilities, the problems encountered, the solutions undertaken and the lessons learned from those projects. The paper summarises the progress made in the past and highlights the challenges faced by TBMs in mining due to complex ground conditions and geometrical requirements. With the technological advances of TBM and experiences gained in the past, more applications of TBMs are expected in underground coal and hard rock mines.CITATION:Zheng, Y, Gong, Q, Li, J and Zhao, J, 2014. A review of the applications of tunnel boring machines in mines, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 691–704 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By K Saito, M Hasegawa

In steelmaking processes, it is known that P2O5 in dephosphorisation slags often exists in solid solutions between Ca2SiO4 and Ca3P2O8, <C2S-C3P>SS, and thus the solid solutions play an important role in the dephosphorisation reaction. Hence, the knowledge of thermochemical properties, ie phase relations and activities of components, in slags containing <C2S-C3P>SS are necessary for the effective removal of phosphorus from hot metal. In this study, the P2O5 activities in <C2S-C3P>SS were measured through the gas equilibrium method. In the present experiment, oxide samples were equilibrated with Cu-P liquid alloys at 1573 K under a stream of Ar + H2 + H2O or Ar + H2 + CO2 gas mixture in which oxygen potential was fixed and then equilibrium phosphorus concentrations in the Cu-P alloys, [mass%P]Cu, were analysed with ICP-OES.

Aug 21, 2024

By Chapman RL

A new process has been developed to remove the impurities copper, cadmium, cobalt and nickel from a zinc plant electrolyte by cementation on zinc dust. The process has been tested in the laboratory and in a continuously operated pilot plant. It has been found that cadmium, in the presence of small amounts of antimony in solution, assists the removal of cobalt. Cementation is conducted in two stages: the first stage for removal of copper with a small excess of zinc dust to produce a relatively high grade product, the second stage for removal of cadmium, cobalt and nickel by addition of zinc dust in the presence of anti- mony. The excess zinc and the cadmium present in the second stage cementate can be selective- ly recovered by slow leaching in spent electrolyte. Zinc dust processes in use elsewhere are described and compared with the present system for use in the Risdon circuit.

Jan 1, 1984

Currently, mining in Australia underpins the economic vitality of the nation, generating massive revenue from commodity exports and providing substantial infrastructure and employment. In addition, it is predicted that mining related services will in the future develop a global market of their own that could eventually grow to rival, in value, the export trade in mineral commodities. There is however little room for complacency. In the short- to medium-term, escalating, vigorous competition can be expected from many previously underdeveloped countries that are reforming their own mining and mineral export industries. In addition, most mining companies are facing a modem-day renaissance in terms of new expectations, changing social norms, evolving employee relations and statutory obligations. Thus, along with whatever promise the future might hold, the mining industry is currently being subjected to a growing number of largely unprecedented problems and pressures, both economic and social, that are both highly complex and demanding. In particular, it remains a matter of on-going concern that relations between mining companies and their employees still, in spite of recent reforms, continue to constrain productivity, perpetuate inefficiencies, affect quality of work life and retard progress towards mutually beneficial goals and achievements. If mining in Australia is to attain and hold on to a commanding position on the global scene, then further changes will clearly need to be made. Realisation of this appears to be growing, with most mining companies having attempted in recent years to improve workplace culture. Based on a wide ranging study, this paper presents an overview of what has been learned to-date with regard to the `people factor&apos; when it comes to implementing and progressing positive change and reform in mining. From this, a number of practical suggestions, arising from hard won lessons and experiences in the field, are offered. Attention to the nine `key principles&apos; given should help to ensure that many of the common problems encountered to-date with change and reform in the mining industry are in future avoided or at least minimised.

Jan 1, 1997

By Marshall T. E, Finfinger G. L

Gulf Coast domal salt mining operations have had sporadic encounters with methane gas emitted without any warning. In virtually all confirmed cases, the methane was localized in methane enriched zones. In a few cases large quantities of methane were expelled rapidly with salt outbursts, resulting in dangerous methane concentrations. Estimates of methane liberated by face blasts in methane-enriched areas is needed in determining how much air should be supplied to the face for proper dilution. A relationship between the gas content of salt samples collected from the face and the amount of methane liberated would be helpful in estimating how much methane will be produced by a face blast. Little is known about the layering or stratification of methane in large area-low velocity airways. This publication reports on three tests conducted by the Bureau of Mines which monitored the immediate return air of four faces during blasting. The test locations were in a methane gas-enriched section that had previously experienced two large outbursts and many smaller ones. A comparison was made between gas content values of face salt samples from the dissolution test and the gas liberation quantities. The characteristic movements of the methane in a large room with low air velocities were charted. This will help to better understand the factors involved in proper placement of methane sensors as a warning system.

Jan 1, 1988

By J Slade, R Trueman

Unplanned dilution has the potential to seriously undermine the economic viability of a mine, and in some cases results in mine closure. The effect of stress damage on dilution has become increasingly relevant as mining depths increase. In the case of narrow vein mining, the incremental extraction of long-hole rings has the potential to result in a moving high stressed zone at the stope brow. This leads the hanging wall and footwall to experience a spike in the stress to strength ratios as the brow passes. In some cases, the stress to strength ratio may be high enough to result in fracturing or damage to the rock mass. The aim of the study described in this paper was to investigate whether stress damage results in a significant increase in dilution. The study involved analysis of overbreak from 410 case studies from the Kundana Gold mine in Western Australia. Site personnel had already undertaken calibration studies of the stress levels that result in rock mass damage. This calibration, in conjunction with numerical modelling showed that stress damaged stope walls at this mine had on average 50 per cent more overbreak than stope walls where stresses had not exceeded the damage criterion. For a design mining width of 1.5 metres, and with both walls impacted, this represents 36 per cent increase in dilution. After adjustment for possible sources of bias the difference reduced to an average 0.10 metres per stope wall, representing 13 per cent dilution for the mining width under consideration. The potential for stress damage related overbreak should therefore be considered as part of any assessment of narrow vein dilution.

Jan 1, 2005

By T Wettainen, G Shekhar, M Stromsten, B Skawina

The aim of a transportation system in an underground mine is to move the rock masses from one location to another in the most preferable manner by minimising the long and short-term operational costs. A continuous improvement of material transportation systems used in mines generates a need for continuous investigation of the current and new underground transportation systems. In an underground mine, an orepass is a common system used to transfer the material to the lower levels. If this system loses the ability to transport or store the necessary material capacities, it would result in production disturbances. In this paper, discrete event simulation (DES) was utilised to analyse the material inflow and outflow of the orepass systems when subjected to the different conditions. The study presented in this paper is based on the Malmberget mine, the second largest underground sublevel caving (SLC) iron ore operation in the world.

Mar 15, 2021

By W Schauenburg

The increasing problems associated with the disposal of waste and the potential for use of by-products as underground filling material is a subject which is relevant not only to the coal-mining industry. The progressive scarcity of surface disposal facilities for by-products and waste has now become a problem in all sectors - not only for the mining industry. The considerable capacity offered by underground cavities which exists in various mining branches present an extremely promising potential in this context. The backfill process for coal mining developed by DMT in co-operation with Ruhrkohle AG make use of the cavities which are offered by the extraction of coal. It consists of several stages: The fine-grained by-products, such as sludge, filter cakes, fine refuse, ash and flue-gas cleaning residues are processed on the basis of specified formulations in metering, blending and pump facilities on the surface to produce pumpable pastes with precisely defined flow characteristics. On Walsum Colliery of Ruhrkohle AG up to 200 m3/h stowing paste is conveyed into the mine in pipes with diameter of 200 mm (8"). The delivery pressure of the pump operating on surface in conjunction with the hydrostatic pressure of the shaft pipe - amounting in total to as much as 25 MPa - makes it possible to convey the stowing material for a distance 12000 m underground up to the workings without any need for additional booster pumps. Via a pipe installed in the face, the paste is pressurised into the cavities in the specially fragmented rock in the mined-out zone well behind the support. Consistent use of stowage of caved-in goafs makes it possible to reduce surface settlement above the workings. Fires in the stowed rock are either smothered or completely prevented thanks to the exceptional air-tightness in the caved goaf and the cooling effects of the slurry stowage. The reduced danger of fire, the preventation of air-leakage and the positive effects on gas emission from the coal improve safety in the workings.

Jan 1, 1998

By T Higuchi, K Fukada, K Takehara, Y Iwami, S Fujiwara

Following the Paris Agreement adopted in 2015 and the SDGs, reduction of CO2 emissions has been taken up as an issue worldwide, and the steel industry, which has a particularly large emission, is required to significantly reduce it. Most of the CO2 generated in the steel industry is generated from the ironmaking process, due to the use of coke and its raw material coal in the ironmaking process. JFE Steel Corporation has been considering the use of hydrocarbon-based gaseous fuels and liquid fuels as a partial alternative to coke breeze used in the sintering process since 2006, immediately after the Kyoto Protocol came into effect in 2005. In a laboratory study, a pot test was used to investigate the effect of the type of fuel, its amount and its injection method on the heat pattern in sinter bed. As a result, the authors developed a technology, in which a predetermined amount of gas fuel or liquid fuel was injected from the surface of sintering bed to extend the holding time of 1200°C or higher at which liquid phase sintering occurs in the layer, to improve the sinter strength while reducing the amount of coke breeze. The authors succeeded in putting this technology to practical use using hydrocarbon-based gas fuel in 2009 and achieved a maximum annual reduction of 60 000 tons of CO2 per sintering machine. In this report, the authors introduce the results of laboratory studies on the use of various energy sources, the practical application of the technology for injecting hydrocarbon-based gaseous fuel into the sintering machine, and the operational results.

Nov 8, 2021

Depending upon the probability one assigns to project go-ahead, up to $10 billion (1978 figures) could be required for resource based projects in Australia in the next decade. In the past major resource projects were readily financeable against sales contracts. In the future the complexities imposed by such matters as political risk, inflation, currency movements and environmental and other socio- economic considerations on project development costs and returns may require a different approach. This paper addresses itself to the ramifications of providing development finance for resource based projects in the future - and in particular examines such factors as project completion guarantees, sales contracts, protection against exchange rate fluctuations, interest rate structures and debt/equity ratios as each relates to the provision of finance. TABLE OF CONTENTS SECTION 1 : Introduction SECTION 2 Factors Affecting Project Financing in the Next Decade SECTION 3 Some Aspects of Financing New Projects in Australia in the 1980&apos;s Conclusion

Jan 1, 1979

By Jones IO

Although small units have been in use formany years, particularly in opal mining at shallow depths, there has been little effort in the past to explore the potential of the vacuum lift system in other more demanding applications. Recent developments in Western Australia by a small number of mining companies, contractors and manufacturers have seen the design and construction of several larger, more powerful units for use in winzing, shaft sinking, hoisting and spillage removal. Some of these units have proved very successful and suggest that they could be developed for a wider range of applications and duties in future.

Jan 1, 1984

By R Justa Cámara, J María Bertrán Llop

"The need for suitable geotechnical characterisation of the rock mass for underground construction is evident. The enlargement project of Railways of the Generalitat of Catalunya (FGC) in Sabadell is a patent example.In general, it is uncommon to encounter problems in the identification and characterisation of certain relevant weak rock formations, which affect project designs. However, all materials should be properly studied, as mischaracterisation can lead to a suboptimal design, resulting in construction problems during the course of the work.Good quality rock is generally not difficult to characterise, but this is not the case for Quaternary or Tertiary cemented soils. Geotechnical investigations based on boreholes do not provide enough information because samples are often badly damaged during the drilling process, if appropriate techniques are not taken. The samples can be altered and may not be representative of the in situ?material.The design and construction of the extension to the FGC line in Sabadell highlighted the importance of the characterisation of Quaternary and Tertiary cemented soils, in particular their rigidity and its underestimation. The twin tunnel project had a total length of 5.1 km, including five stations with 3.5 km excavated by tunnel boring machine (TBM). The remaining 1.6 km was constructed using cut and cover methods. The TBM portion of the tunnel had a bored diameter of 6.83 m with an internal radius of 3 m and 0.25 m thick precast concrete segments. Much of the tunnel alignment passed through and was affected by the presence of certain stiff layers of Quaternary cohesive materials.In this paper the TBM challenges faced will be discussed in detail. In particular:&nbsp; TBM excavation rate reductions and overheating problems due to the required excessive thrust and torque floating problems in the lining due to nil earth pressure over the rings and the development of an improved, controlled setting time mortar to address this issue block-in and block-out methodology for each station, in some cases with internal blocks to prevent earth pressure drops and soil scouring the relevance of performing simpler solutions, for example, hyperbaric interventions to examine the cutter wheel tools when it has been shown that interventions under atmospheric conditions were equally feasible the implementation of conventional bivalve machines as standard procedure for excavation of diaphragm walls in stations, where in fact, hydrocutter machines or pile boring machines may have been required, given the mechanical characteristics of the materials to be dug out.CITATION:Justa Cámara, R and María Bertrán Llop, J, 2014. Underground extension of the FGC line in Sabadell through cemented soils, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 161–170 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

By J Zhou

Gold in sulfide ores is associated predominantly with sulfide minerals and occurs as both microscopic and submicroscopic particles. In non-refractory sulfide ores, gold occurs mainly as coarse- and medium-grained particles. Minute inclusions and submicroscopic gold usually account for a minor portion. In contrast, gold in refractory sulfide ores occurs mainly as minute particles and submicroscopic gold, and microscopic gold usually accounts for an insignificant portion. In gold ores containing carbonaceous material, the preg-robbing nature of carbonaceous material may impose challenges on gold extraction and cause gold losses. To extract gold from refractory sulfide ores, the ore needs to be finely ground and preoxidation is often required. Sulfide host minerals must first be oxidised to create a porous structure through which the cyanide leach solution can penetrate to reach the colloidal gold particles. The oxidation is traditionally achieved by roasting, autoclaving or bacterial oxidation. In carbonaceous sulfide ores exhibiting a preg-robbing nature, the carbonaceous material needs to be treated by roasting, autoclaving or other means to minimise the preg-robbing effect. As a predictive and troubleshooting tool, the gold deportment study plays an important role in gold metallurgy. It determines the deportment of gold in an ore or mill product and identifies the mineralogical issues that may affect or may have affected gold extraction. The information acquired from a gold deportment study can be used to assist in process selection, flow sheet development, recovery improvement and reagent optimisation.CITATION:Zhou, J, 2013. Deportment of gold in sulfide ores and implications for gold extraction, in Proceedings World Gold 2013 , pp 433-442 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By Y, Li Jianxiong, Hu Hua, Gu Desheng

After having briefed the technical and economical advantages of continuous mass mining in underground metal mines, the authors discuss the four stages of research and development of continuous mass mining in China. The four stages are: vibrating ore drawing in a stope, continuous mass mining in a stope continuous mass mining without rib pillars in an area and continuous mass mining in whole mine. The authors briefly review the research achievements of the first and the second stage; Combining the key national research project of the æNinth Five Year PlanÆ ù æThe experiment and research of continuous mass mining without rib pillarÆ, the authors introduce in detail the technological condition of mining, the design ideas of continuous mass mining, the design scheme of mining, the technology of mining. the equipment of mass mining, the chief research achievements and so on. The success of research of continuous mass mining without rib pillar indicates the arrival of the third stage of research. The introduction of continuous mass mining will promote the technology revolution of mining in China remarkably. The authors also point out that the development direction of continuous mass mining of the 21 century is continuous mass mining in whole mine, which is the fourth stage of research.

Jan 1, 2000

Today, more and more tunnel ventilation systems are based on NO2 (or NO) and visibility measurements. Due to the significant decrease of CO emissions in countries with EU emission standards, which were adopted by Australia in 2004, CO is no longer a key factor for tunnel air quality monitoring and is often only measured for plausibility reasons (eg according to the German guideline RABT2006). Nitrogen dioxide, which is a good indicator for the overall air pollution along roads, is now taking over the leading role not only for ventilation control but also for air quality monitoring and in future probably for checking the function of air filtration plants in tunnels. Due to the lack of equipment for reliable and long-term NO2 measurements in road tunnels in the past, there are only very few standards giving limit values for NO2 in road tunnels. Furthermore there are not many records of NO2 readings over longer periods in different types of tunnels. SICK MAIHAK, a major supplier of measurement devices for controlling tunnel ventilation, has introduced the first monitor in 2006, specifically designed for measuring NO2, NO and visibility simultaneously in road tunnels. There are now experiences and results from the first tunnels equipped with this kind of system. This paper will present and discuss the results and experiences from these tunnels and explain the different levels of NO2 in different tunnel types. Furthermore, the status of air quality standards for road tunnels regarding NO2 limit values and the current status of discussion in various countries about NO2 limits will be presented.

Jan 1, 2008

By E Broers, J Goh, S Davies

With recovery being important in optimising the business performance of a laterite and sulfide plant and with water being a precious resource in Australia, there has been increased pressure for companies to improve their methods of improving liquor recovery and improving water recovery in both laterite and sulfide plants. This has resulted in new control technologies such as the Manta Cube being applied on countercurrent decantation (CCD) and thickening circuits which is necessary to improve stability and optimise the liquor and water recovery in these processing plants. This paper describes the benefit of applying these new control techniques on CCD and thickening circuits in some of the mineral processing plants in Australia.

Jan 1, 2009