Search Documents

The Australian mining industry is at an interesting stage in its development. Of the large number of mining companies in Australia, some are still solely domestic in their focus. others have made their first tentative forays offshore, and others are global players of significance in the world industry. It is not long ago that the entire industry was almost exclusively domestic in its focus. Very few companies before the early 1980s had ventured offshore, and those that did so were considered quite risque. The initial moves were made mainly by large companies who could afford to lose the funds expended in getting started in a range of offshore locations.

Jan 1, 1995

By Shiels O. J

The major Permian coal deposits of N.S.W. are in the Sydney-Bowen Basin and associated small deposits occur in structurally isolated areas; a further deposit is present in the Oaklands Basin. - The Sydney-Bowen Basin in New South Wales comprises the sub basins, the Sydney Basin and the Gunnedah Basin. Coal measures in these basins are near the top of the Permian succession and within and below an underlying marine sequence. The coal deposits can be conveniently described in units in which the coal geology is homogeneous. The Clyde Coal Measures and Yarrunga Coal Measures contain no seams of economic significance and occur beneath the marine beds in the south of the Sydney Basin. The Greta Coal Measures are economically significant and represent a brief interlude in the marine sequence in the north of the Sydney Basin and equivalents are present in the east of the Gunnedah Basin. The Tomago Coal Measures crop out above the marine sequence east from the Lochinvar Anticline and dip southeast to uneconomic depths. The Newcastle Coal Measures are historically and economically very important and overlie the Tomago Coal Measures and these measures will continue to be important although future mining will be faced with greater depths. To the west of the Lochinvar Anticline the Singleton Coal Measures, equivalent to the Tomago and Newcastle Coal Measures, crop out. This unit represents the thickest development of coal measures in the State and has a very large potential for both open cut and underground mining. Equivalents of the Singleton Coal Measures, the Black Jack Coal Measures and the Booroomin Group crop out on the east side of the Gunnedah Basin and probably are widespread across the Basin. They have less economic potential than the Singleton Coal Measures. In the southwest of the Gunnedah Basin, Illawarra/Singleton Coal Measures crop out over extensive areas and possibly have a large potential for underground mining under low cover. The Illawarra Coal Measures are exposed along the western margin of the Sydney Basin and thicken as they dip into the Basin across a shelf. The outcrop area is currently mined and the shelf has considerable potential for future mining. The highest rank coals in the State are in the Illawarra Coal Measures in the south of the Sydney Basin. The deepest coal mining is in this area and its continuing success is of great importance to the future exploitation of the resources of the Basin. The Tomago, Newcastle, Singleton and Illawarra Coal Measures extend into and meet in the central area of the Sydney Basin but they are under thick cover and are not considered to be economic at present. Permian coal measures occur in isolated areas in the New England Fold Belt and have limited economic potential. The Oaklands Basin in the south of the State contains a large reserve of low rank coal.

Jan 1, 1975

By Player WP

The legislative operating environment, or the mineral regime, that a country has to offer is one of the key determinants that a company wanting to invest in an area takes into account in formulating its investment decision. The New Zealand Government recognises this and the importance of getting the regime right in order to provide for continuing investment in mineral exploration and mining in New Zealand. In recent years, the Government has given considerable attention to developing legislation which provides for investment to take place; for those making the investments to have a stable, fair and open investment environment with government intervention only when considered absolutely necessary because other approaches are not working; and for the people of New Zealand to know that investment must meet acceptable health and safety standards and have acceptable impact on the environment. Also of key importance is having a clearly defined mining regime which includes rules on how to obtain a permit and rules in respect of ongoing permit compliance, rights to develop a mineral resource and permit conditions (in particular, the royalty regime). In New Zealand, these matters will all be addressed in what are referred to as "minerals programmes".

Jan 1, 1995

By Gutsche O, Kapur PC

Experimental data on the production of fines as a function of specific grinding energy consumption show that in general the energy utilisation in a choke fed high-pressure roll mill is higher than in a ball mill, but lower than in the single-particle mode of comminution under slow compressive loading. There is some evidence to suggest that the presence of water in feeds improves the energy efficiency of pressurised roll milling somewhat. Within a wide range of energy input, the size distributions of the ground product are self-similar, the logarithmic median size decreases linearly with the amount of fines produced and the inverse of the median size increases linearly with the energy spent. The production of fines as a function of energy expended follows essentially the same pattern as the one frequently encountered in media mills. The kinetics of grinding in the high-pressure roll mill can be simulated satisfactorily by modifying the standard particle population balance equation in order to account for energy dissipation in the tightly compressed bed. Common characteristics and important differences in grinding by the media mill and the high-pressure roll mill are highlighted.

Jan 1, 1993

By Brady B. H

Increasingly, consideration is being given to the nominal `outcomes' of degree courses in engineering, including mining engineering. These are concerned not only with knowledge and technical understanding but also with capabilities in the professional application of engineering principles to problem solving, multi-disciplinary teamwork, communication and life-long learning. This paper discusses concepts of education, professional formation and training and the associated development of competencies in applying knowledge, understanding and technical insights and skills to new situations. In developing guidelines on preferred attributes and competencies in graduate mining engineers, a survey was conducted of a range of industry personnel involved in selecting graduate mining engineers. The results not only clarified the spectrum of competencies sought but also provided valuable detailed views to assist in defining a mining engineering curriculum. Considering a greater concern with the development of more `well-rounded' graduates, the implications are discussed with regard to teaching and assessment activities and the time demands on academic staff when a `coaching' role is emphasised. In line with international and Australian moves in engineering education, notions on education of mining engineering graduates in Australia are under review. The results will provide continuing challenges to all involved.

Jan 1, 1997

By Collings P. S, Adair D. L

The Upper Robe (Robe Gorge) deposits occur in Kumina Creek and the Robe River, some 20-40 km upstream from mining operations at Pannawonica. The Gorge Deposits were rec- ognised, mapped and sampled in 1962-3 and re- examined in detail in 1971. Approximately 180 mineralized occurrences were mapped in 1971 on 1:4800 scale and 50 of these were remapped in detail at 1:1200 scale. Eighty cross sections were measured and sampled and 300 geological maps prepared. In addition 88 holes totalling 7388 feet were drilled in three occurrences considered to have the greatest potential. The Gorge Deposits occur in the Robe Pisolite unit which forms thin remnant crusts, bay fillings and occasional cut-off meanders along the edge of the present streams. Less than 50 of the deposits have tonnage potential of one million or more. Consequently exploit- ation of the Gorge reserves must be considered as a very uncertain, long range possibility because the deposits are small and scattered throughout the gorges in the area, thereby necessitating costly railroad spur lines to gain mining access. Grade of the occurrences is extremely variable over short distances both vertically

Jan 1, 1973

By Draper J. J, Lang S. C

Regional geological mapping and facies analysis of the Late Devonian to Early Carboniferous Keelbottom Group of the Burdekin Basin have resulted in a depositional model representing six siliciclastic-carbonate facies. The six facies represent alluvial fan, braidplain delta, siliciclastic shoreline, siliciclastic shallow marine, restricted siliciclastic/carbonate shelf, and carbonate shoal depositional environments. These facies are identified in the Star beds which are equated with and included in the Keelbottom Group in this paper. Facies are repeated throughout the Group, as a result of two transgressive-regressive cycles.The first transgression recognised in the Keelbottom Group began in the mid-Famennian, and followed deposition of the Late Devonian Dotswood Group. It was marked by the deposition of Siliciclastic Shoreline facies in the basal Myrtlevale Formation, which was succeeded by Siliciclastic Shallow Marine facies at the peak of the transgression. The return of Siliciclastic Shoreline facies in the upper part of the Myrtlevale Formation marked the onset of the first regression, which resulted in the progradation of Braidplain Delta facies from the northwest of the basin. During the peak of this regression, deposition in the western part of the basin was dominated by Alluvial Fan facies.

Jan 1, 1990

A number of suggestions have been made to improve the design of cells used for electro winning and electro refining of metals. Most of these designs have been aimed at increasing the current density used in order to improve cell capacity, although the purpose of some has been to produce electro deposited metals in a continuous manner. Improvements in the electrolyte flow pattern in conventional cells have resulted in an increase in the rate of mass transport of metal ions to the electrode surface; giving rise to lower concentrat- ion polarization and an improvement in the nature of the product obtained, Other cell designs are based on a moving electrode, usually a rotating disk, and these may include provision for removal of the product in a continuous manner, The maximum current density which can be used in an electro- lytic deposition process is determined by the limiting diffusion current, the physical nature of the, product, the purity of the product required and by the increase in power costs which result from the higher cell voltages, This paper examines the properties of an agitated bed of particles as an electrode system when used for a metal deposition Process,

Jan 1, 1969

By P K. M Mazzoni, D Frantois-Bong

This paper aims to show alternatives to the estimation methods used for finding the parameters in GyÆs well known model for sampling variance in the case of particulate materials. Many experiments designed for gathering data on the sampling variance for specific mineral deposits allow the experimenter to use approximations in the calculation of the parameters of the mathematical model involved, which sometimes can be very useful. However, there are some instances where approximations lead to biased estimates of the parameters, and consequently, lead to errors in the establishment of the sampling protocol and treatment of quality control data. In the present work, an alternative is presented for computing the parameter values based in any experimental set up, without the need for any simplification. The method was derived using the method of least squares and evaluations are made using the usual tools in this kind of methodology: residual analysis and evaluation of the fit by means of a plot of calculated versus experimental variances. With the aid of these tools, one can better evaluate the structure of the experimental errors in such applications, and the adherence to the proposed model. In addition, it is possible to perform hypothesis testing for the equality of different sampling procedures in terms of sampling variance. The full mathematical details are given, together with an algorithm for applying the method, which can be implemented easily using any computer language. An illustration of the method is shown, considering the international work done in ISO/TC 102. This example is a determination of the minimum sample mass to be collected in iron ore shipments, in order to achieve a specified sampling precision.

Jan 1, 2005

In Australia a social impact assessment (SIA) is generally required prior to the approval of a mineral resource extraction or processing projects as a part of the Environmental Impact Assessment (EIA) process. In recent years there has been increased attention on the adequacy of the SIA process applied in major project assessment. Most applications have focused on the impact identification process with little attempt given to the community negotiating power over how impacts will be addressed. The impact assessment tends to occur at a single point in time, with no subsequent re-evaluation or ongoing social impact management and monitoring process. The assessments rarely specify how responsibilities for impacts on communities may be apportioned between project proponents and government, and have been inadequate in dealing with cumulative project impacts. In Queensland, concern about these shortfalls have led to the release of the Sustainable Resource Communities Policy 2008 and requirements for social impact management plans (SIMP) to be developed for each resource development in the State. In this paper a 'pressure-state-response' approach to impact assessment is used to develop an 'impact-response-monitoring-evaluation' (IRME) framework that can be applied to ongoing evaluation and monitoring of social impacts. The framework is applied to coal resource developments in the northern Bowen Basin in Queensland to identify core requirements in a SIMP. The IRME framework is flexible enough to be implemented at various spatial and time scales, for the wellbeing of the local and regional mining and non-mining communities in Australia. The framework can be further examined in other mine developments and could be integrated with the existing mining or environmental protection acts.

Jun 1, 2010

By A Robertson

Australia has been slow in adopting the use of underground space as a part of our urban planning process. Australia has one of the highest levels of tunnel advance per capita per annum in the world, yet the use of underground space in our cities appears difficult for our planners and politicians to comprehend, not withstanding the general availability of good quality rock and contractor expertise in Australia. However, the lack of space in our urban areas is being highlighted as our major cities expand outwards and people and businesses gravitate towards city centres. Typical potential underground space uses include car parking, self-storage and archiving facilities, water storage, underground quarrying, small industrial facilities and another layer of traffic (electric and fuel cell) and services network. Historically, blasting in high density population areas has resulted in blast vibrations and blast overpressures exceeding the limits, which in some case have been set extremely low in terms of peak particle velocity (PPV). This makes conventional blasting difficult, often requiring low charge weights per delay and associated small blast sizes and slow advance rates. However, the introduction of new technologies, such as computer aided drilling, electronic delays and low-energy explosives has made this task considerably easier. Although more expensive than conventional blasting, excavation by blasting using these products and technologies in relatively good quality ground is believed, in most cases, to be less than the cost of mechanical excavation. In this paper, the authors look at innovative trends in underground quarrying, underground commercial space and tunnelling and put forward their concept of future excavation demand, future product requirements and technical specifications to the drill and blast community.

Jan 1, 2007

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Davies B, Rogers A, Grainger A, Todd J, Brenman R, Jones L, Horton B, Eager L

Research into the control of diesel particulates (DP) has been. conducted by BHP Coal for more than 7 years. Personal monitoring of employee exposures (n = 480 full shift samples) conducted at nine underground coal mines has indicated that the exposure of the workforce ranges from less than 0.1 to 2.2 mg/m3 of DP dependent on job type and mining operation. Approximately 50% of the mass of DP captured is elemental carbon (EC) which is the species currently being considered by some international regulatory authorities as the exposure standard. Five technologies for controlling DP were investigated in a combination of studies conducted in an above ground simulated tunnel, in a special controlled section of underground mine roadway and validated by application in standard coal mining operations at Tower Colliery. Tests conducted under controlled conditions indicate that dependent on the type of fuel in use, the introduction of low sulphur fuels can reduce DP levels in return airways by up to 50% and in actual mining situations a reduction of 20% can be achieved in exposure of the workforce. In addition, subjective responses from the workforce indicate that exhaust emissions from low sulphur fuels provide lower irritation and a more pleasant aroma. The use of water filled scrubber tanks reduces the level of DP emissions by 25%. Chemical decoking of engines resulted in a reduction of 20% in DP in return airways. A commercially available non-flammable disposable dry exhaust filter constructed from synthetic organic fibres with an operational lifetime in excess of 20 hours was found to reduce DP exhaust emissions by 80%. Investigations have indicated that the use of increased ventilation to control DP levels particularly in multiple vehicle situations does not follow a simple dilution factor and in some instances compliance with current regulatory requirements may not produce the required reduced exposure levels. The results from single component control strategies provide considerable reduction in exposure to DP, however the most efficient and cost effective control methodology is the use of a combination of individual systems modelled to operations conducted at each mine.

Jan 1, 1998

By S C. Bhowmik, R Gupta

This paper presents the ventilation problem faced by Jaduguda uranium mine, operated up to a depth of 905 m. The first two stages of the mine workings are up to 555 m, which are nearly exhausted. The third stage of the mine is from 555 m to 905 m and presently most of the stopping and development activities of the mine are carried out in the third stage. The total available intake quantity in the third stage was only 21 m3/s. As a result, the mine was facing a radiation hazard. The different instruments and the methods used for monitoring of radiation levels are also presented in the paper. It was observed that the average individual effective dose (external + internal) of radiation workers in Jaduguda mine increased from 6.93 mSv/y in 1995 to 9.5 mSv/y in 2001 and during this period the average individual effective dose of mine workers of the world was less than 5 mSv/y. Keeping this problem in view, a detailed ventilation investigation has been carried out in this mine. Initially the requirements of intake air quantity have been assessed by carrying out field investigation in different stopes and it was found that the third stage workings require nearly 100 m3/s. A detailed ventilation survey has been carried out in the total ventilation network and a basic ventilation model of the mine has been prepared. Different alternative schemes for effectively ventilating the third stage workings of the mine were simulated and a set of recommendations were made for implementation. The recommendations were partially implemented in 2002. As a result the total intake quantity to third stage workings increased to nearly 70 m3/s and the average individual effective dose (internal + external) of mine workers came down from 9.5 mSv/y in 2001 to 6.65 mSv/y and 6.60 mSv/y in 2002 and 2003 respectively. The implementation of remaining recommendations is in progress. Finally, a mathematical model has been formulated from the first principle for predicting air quantity requirements in cut and fill stopes in uranium mines and this model is being validated for further use.

Jan 1, 2005

By Singleton T

Increasing world competition puts pressure on sales volumes and prices. This in turn reduces potential profit margins. This in turn increases the focus on costs.Increasing demands on quality and service puts pressure on delivery performance - the right product at the right time. This in turn reduces the scope for errors and delays - and this in turn increases focus on equipment reliability. In the mining industry, both costs and equipment reliability have one significant thing in common - they are driven substantially by maintenance.

Jan 1, 1998

By U Dzharlkaganov, B Bekmurzayevand M

The principle conception is presented of timely planning of winning operations in complex-structural blocks and faces in week-24-hourly regime. For adequate description of complex interconnections of open cast operation in space and in time and solving of optimisation problems in timely regime it is necessary using of complex logical and calculation procedures.

Jan 1, 2003

By J G. Webster-Brown

The Tui Mine is located near Te Aroha at the base of the Coromandel Peninsula. It was a lead-zinc mine, which closed in 1973 due to declining concentrate prices, high overheads, and high mercury levels in the ore. The site was abandoned, leaving behind an acid rock drainage generating system, including a sulfide-rich tailings dam which has since caused pollution of Tui Stream, as well as open adits and waste piles which drain predominantly into the neighbouring Tunakohoia Stream. At the AusIMM conference in 2003, Harvey and Webster-Brown presented water quality results from the Tui mine site and lower stream catchments in 2002. In April 2006, Environment Waikato undertook remediation works to stabilise the dam and reduce acid drainage entering Tui Stream. In this study, water quality results from the Tui mine site and lower stream catchments are again being determined, in order to compare with the pre-remediation results. Preliminary data collected for summer indicate a minor but consistent improvement in water quality in the lower stream catchments, although lower Tui Stream continues to exceed ANZECC (2000) aquatic life guidelines for Cd, Cu, Pb and Zn. This slight improvement may be due to a decrease in the flow of ARD into Tui Stream, as there does not appear to have been an improvement in quality of the contributing ARD waters.

Jan 1, 2007

It has become increasingly clear in recent years that human kind has developed the capacity to alter the environment of the Earth on a global scale. The changes are often subtle. This is particularly true in the case of stratospheric ozone. Ozone is produced primarily in the stratosphere, at altitudes in excess of 20 km, initially through the action of ultraviolet sunlight dissociating molecular oxygen. According to theory as it existed up to a few years ago, ozone is removed mainly by reaction with atomic oxygen. In the unperturbed environment, this reaction proceeds both directly, and by paths catalyzed by trace quantities of nitrogen radicals. Molina and Rowland [Nature, 249, 810, 1974] pointed out that decomposition of industrial chloroflurocarbons could in-troduce an additional source of radicals to the strato-sphere. Chlorine radicals are even more efficient than nitrogen in catalyzing recombination of oxygen atoms with ozone; models suggested that we might expect reductions in the vertical column density of ozone of as much as a few per cent over the next several decades. A reduction in ozone of x¦/a, by increasing the flux of ultraviolet sunlight reaching the surface, was predicted to result in an increase of about 2x% in the number of cases of skin cancer, with other less well defined impacts on the non-human environment for life.

Jan 1, 1990

By Ren T. X, Jozefowicz R

In many branches of engineering, there has to be an understanding of the motion of fluids in order to solve problems. Many safety and health problems in the mining industry are typical examples that involve the understanding and analysis of fluid flow, such as explosions, the spread of fires, dispersion of gas and dust, and ventilation patterns. Computational Fluid Dynamics (CFD) is concerned with the use of computers to produce information about the ways in which fluids flow in given situations. Until recently CFD has been widely applied to a variety of industrial sectors and increasingly to problems in the health and safety areas. With the arrival of more powerful computers and CFD packages, CFD techniques are no longer practised solely in a research environment, but can be used by engineers in many industrial fields. This paper introduces the basic concepts and general procedures involved in the use of CFD technology. A comparison is given as a guide to the major features of a number of widely used commercial CFD codes. Areas of potential CFD applications are identified in a range of safety and health problems in mining industry. An example is presented to illustrate the use of this technology. It is believed that the exploitation of these areas using CFD approach will contribute significantly to the solution of today's many mine health and safety problems.

Jan 1, 1995

By Graham J

The successful processing of arsenopyritic ores is difficult and will be facilitated by a better understanding of the mineralogy of gold within arsenopyrite and the type of arsenopyrite in which gold is taken up. Solid solution gold in arsenopyrite is now well documented, and is a significant cause of refractory behaviour in gold processing. Investigations of the crystal structure and stoichiometry of arsenopyrite by X-ray diffraction, electron microprobe analysis and convergent beam electron microscopy have been carried out in order to understand how the gold is incorporated into the structure. Variations in stoichiometry, particularly the As:S ratio, of arsenopyrite leads to variations in structural parameters. These variations result in slight changes in thermal behaviour. The distribution of invisible gold in an arsenopyrite grain is generally non-uniform and synthesised samples contain up to 2 wt per cent gold. A transmission electron microscopy (TEM) technique called ALCHEMI is being used to identify the substitution site. The process of gold agglomeration together with evidence of an ordered breakdown of arsenopyrite to pyrrhotite has been documented with the use of TEM. An arsenopyrite grain containing invisible gold was heated with an electron beam resulting in recrystallisation of arsenopyrite to pyrrhotite with arsenic being expelled. The gold is mostly insoluble in the pyrrhotite lattice and therefore exsolves out and combines with other gold atoms to form droplets at the boundary of the pyrrhotite.

Jan 1, 1992